Abstract
Fast-growing metal-accumulating woody plants are considered potential candidates for phytoextraction of metals. Shuikoushan mining, one of the biggest Pb and Zn production bases in China, presents an important source of the pollution of environment during the last 100 years. Over 150 km2 of fertile soil have been contaminated by the dust, slag, and tailings from this mining. The goal of the present work has been to determine the content of Pb, Zn, Cd, and Cu in wild woody plants (18 species) naturally growing in this area. Two hundred five plant and soil samples from 11 contaminated sites were collected and analyzed. In addition, to assess the ability of multi-metal accumulation of these trees, we proposed a predictive comprehensive bio-concentration index (CBCI) based on fuzzy synthetic assessment. Our data suggest some adult trees could also accumulate a large amount of metals. Pb concentrations in leaves of Paulownia fortunei (Seem.) Hemsl. (1,179 mg/kg) exceeded the hyperaccumulation threshold (1,000 mg/kg). Elevated Pb concentrations (973.38 mg/kg) were also found in the leaves of Broussonetia papyrifera (L.) Vent., with a Pb bio-concentration factor of up to 0.701. Endemic species, Zenia insignis Chun exhibited huge potential for Zn and Cd phytoextraction, with the highest concentrations of Zn (1,968 mg/kg) and Cd (44.40 mg/kg), characteristic root nodules, and fast growth rates in poor soils. As for multi-metal accumulation ability, native species B. papyrifera was calculated to have the most exceptional ability to accumulate various metals simultaneously (CBCI 2.93), followed by Amorpha fruticosa L. (CBCI 2.72) and Lagerstroemia indica L. (CBCI 2.53). A trend of increasing metal from trunks to leaves (trunks < branches < leaves) and towards fine roots has been shown by metal partitioning between tissues. The proposed CBCI would allow for the selection of suitable trees for phytoremediation in the future.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
Heavy metal contaminants are ubiquitous in industrialized societies. They are one of the most serious environmental problems currently facing mankind. Metal-polluted soils are receiving increasing attention because of their persistence and hazardous effects on the environment and human health (Bhargava et al. 2012; Khan et al. 2008; Peuke and Rennenberg 2005). Various physical and chemical remediation methods may be useful in the restoration of polluted soils of limited areas, but are usually very expensive (Sarma 2011; Douay et al. 2008; Glass 1999). Most of these methods have adverse effects on the properties of the soils, and render the soil useless for plant growth (Danh et al. 2009). Phytoextraction is an emerging technology that has received significant scientific and commercial attention because of its elegance and the vast extent of contaminated areas (McGrath and Zhao 2003; Pedron et al. 2009). However, continuous phytoextraction requires perennial, easily manageable plants that could accumulate large amounts of metal pollutants in their aerial tissues while producing high biomass (Maric et al. 2013). Very few available hyperaccumulators meet these criteria (Baker et al. 2000). As an alternative to herbaceous hyperaccumulators, fast-growing, metal-accumulating woody plants have been considered as potential candidates for the development of feasible phytoextraction (e.g., Pulford and Watson 2003; Unterbrunner et al. 2007; Puschenreiter et al. 2010).
Numerous studies on this topic are reported in the literature; however, most of them report the use of poplar and willow for the remediation of Cd and Zn polluted soils, and compare either a limited number (<5) of species (Shi et al. 2011; Unterbrunner et al. 2007; Wang and Jia 2010) or a high number of clones from a single species (Di Lonardo et al. 2011; He et al. 2013). These studies were usually conducted in controlled hydroponic, pot or field conditions, using young cuttings of different species with short growth periods. Direct comparisons of metal concentrations between adult woody species are scarce. To better explore the metal accumulation properties of woody species, further field screenings are required.
As trees have varied ability to accumulate different metal pollutants, and most contaminated areas have combined pollution, it is necessary to assess the overall performance of trees in terms of metal accumulation for phytoremediation practice. Fuzzy synthetic assessment is an effective method for overall evaluation when multiple factors need to be considered (Chen et al. 2012). It is used broadly, for example to evaluate urban air quality (Onkal-Engin et al. 2004), for the estimation of methane generation rate constants for landfills (Garg et al. 2006), and for the assessment of the environmental lodging stress for maize planting (Mi et al. 2011). The continuum of values is between 0 (full non-membership) and 1 (full membership) in a fuzzy membership function. The fuzzy evaluation method has the advantage in combining results of several influencing indicators into one relative measurement index. No attempts to date have been made to evaluate the metal accumulation capabilities of plants by this method.
In this study, a field screening program was conducted in the Shuikoushan Pb/Zn mining and smelting area and surrounding areas in Hunan, China. Eleven sites were chosen based on the pollution situation of this area (Sun et al. 2011) and the distribution of the existing adult woody plants. Tissues of these woody species along with soils from their root zone were collected. Eighteen species were investigated, including 12 tree and 6 bush species. The concentrations of Pb, Zn, Cd, and Cu were analyzed in plants and soils. The aims of this screening program were as follows:
-
Identify the accumulation status of the adult trees of the 18 species to determine the metal concentrations in their leaves and their bio-concentration factor.
-
Propose a comprehensive bio-concentration index (CBCI) to assess the overall performance of the woody species in terms of multi-metal accumulation.
-
Compare the comprehensive accumulation ability of these woody species, and assess their feasibility for phytoremediation.
-
Explore the distribution regularities of metals in the different tissues of selected metal accumulator species for optimization of biomass production and phytoextraction.
Materials and methods
Description of sites and sampling procedure
The survey was conducted in the Shuikoushan Pb/Zn mining and smelting area and its surrounding region in Hengyang, Hunan, located between latitudes 26°25′58′′–26°36′11′′ and longitudes 112°22′34′′–112°42′58′′ (Fig. 1). The mine was created in 1896 and is still one of the biggest Pb and Zn production bases in China. It generates a significant quantity of dust, slag, and tailings every year, and contaminates the surrounding areas over several kilometers (Sun et al. 2011; Wei et al. 2009). This area falls in a subtropical zone with a warm, wet climate characterized by an annual average temperature of 17.8 °C and an average precipitation of 1,457.00 mm (Table 1).
Based on the pollution situation (Sun et al. 2011) and the distribution of the adult trees available in this area, 11 sites were chosen for investigation (Fig. 1). Each site had at least one woody species and each species had more than five adult individuals. The species investigated at each site are listed in Table 2. Leaves were collected randomly from the whole tree canopy (about 80 g DW) and mixed to a homogeneous sample in September 2012. Three to five replicates were used for each species at each site. We collected 102 plant samples from 18 woody species in total. The number of plant specimens at each site were 5 (site 1), 13 (site 2), 9 (site 3), 5 (site 4), 8 (site 5), 13 (site 6), 14 (site 7), 10 (site 8), 5 (site 9), 8 (site 10), and 12 (site 11). Soil sampling was conducted according to the S-shaped sampling method (He and Ma 2000). At each site, the sampled trees were circled and the circled area was regarded as sample area. The S-shaped belt transect was arranged according to the distribution of the sampled trees and occupy trees' localities as many as possible. Five points were equally distributed in the belt transect. Three soil samples were taken from 0, 10, and 20-cm depth and homogenized to a composite sample at each point. The five samples from the five points in the belt transect were the five replicate at each site.
Leaves, branches, trunks, and roots were taken from selected specimens of Broussonetia papyrifera (L.) Vent. at site 8 and Paulownia fortunei (Seem.) Hemsl. at site 4 in October 2012. Three samples of about 80 g (DW) from each tissue of each tree species were collected. Trunk samples were taken at a height of between 0.5 and 1.5 m using pruning shears. Branch samples were taken randomly from the whole tree canopy using a tree trimmer. Leaves were distinguished into tender, functional, and older (yellow but still attached), and roots were distinguished into coarse (>2 cm), intermediate (2 mm–2 cm), and fine (<2 mm).
Analysis of plants and soil
Leaves, branches, and wood from the trunks were gently washed three times with deionized water to remove soil particles. Root samples were first washed three times with tap water, followed by deionized water to remove any soil or tailing particles attached to the root surfaces. Finally, roots were exposed to a 0.05 M CaCl2 solution to remove metals from the apparent free space of the root as completely as possible. All plant samples were dried at 65 °C to constant weight before they were ground.
Soil samples were air-dried and ground and then passed through a 2-mm stainless-steel mesh for pH analysis (Sartorius PB-10, Germany). The soil/distilled water was 1:2.5 (v/v). Samples were then passed through a 0.15-mm stainless-steel mesh for organic carbon and total nitrogen analysis (GB 7857-87, GB 7173-87), and for total metal (Pb, Zn, Cd, Cu) analysis.
Plant samples (0.1 g) were digested using a mixture of 6 ml HNO3 and 2 ml H2O2 in a closed microwave system (CEM MARS6, USA), and soil samples (0.15 g) were digested using a mixture of 5 ml HNO3, 4 ml HF, and 2 ml HClO4. Measurement of Pb, Zn, Cd, and Cu concentrations was then performed by ICP-MS (Agilent 7700×, USA). Replicate samples, certified reference materials (GBW 07604, GBW 07405, China) and blanks were included for quality assurance.
Application of fuzzy synthetic evaluation and proposal of comprehensive bio-concentration index
In our study, we applied the membership function of fuzzy synthetic evaluation to assess the trees' comprehensive accumulation ability of multi-metals through several pollution influence factors such as Pb, Zn, Cd, Cu, etc. The CBCI was proposed to stand for comprehensive metal accumulation ability as follows:
-
1.
The fuzzy set or the factor set U: U = (u1, u2, u3 …… ui), here U is the trees' comprehensive accumulation ability level, and ui are those various metal pollution factors.
-
2.
Bio-concentration factors (BCF), also known as accumulation factors or enrichment factors, which are defined as the ratio between total metal concentration in leaves and soil, have been previously used to estimate the ability of plants to accumulate a certain heavy metal (Harada et al. 2011; Liu et al. 2008; Shi et al. 2011). The value of fuzzy membership function for trees' accumulation ability of each metal pollution factor (BCF) can be calculated by the formula as follows:
$$ \mu (x)=\left\{\begin{array}{cc}\hfill 0\hfill & \hfill x=x \min \hfill \\ {}\hfill \frac{x-x \min }{x \max -x \min}\hfill & \hfill x \min <x<x \max \hfill \\ {}\hfill 1\hfill & \hfill x=x \max \hfill \end{array}\right. $$Where x is the BCF of a certain metal pollution factor, x min is the minimum value of the BCF of the metal among the woody species investigated, and x max is the maximum value of the BCF of the metal among the woody species investigated. The maximum μ(x) is denoted as the fuzzy membership value 1, which has contributed most to the trees' comprehensive accumulation ability of various pollution factors. The minimum is denoted as the fuzzy membership value 0, which has contributed the least to the trees' comprehensive accumulation ability of various pollution factors, or low provision level.
-
3.
Calculation of the evaluation index:
$$ \mathrm{CBCI}=\left(1/\mathrm{N}\right){\displaystyle \sum_{i=1}^N}{\mu}_i $$where N is the total number of metal analyzed, and μ i is μ(x) of metal i.
Results
Soil characteristics
The main characteristics of the soil from each site are given in Table 1. The pH ranged from 5.07 to 8.08. Soils collected from sites 5, 6, and 7 had significantly higher pH (p < 0.05) (Table 1). The reason for this difference may be the tailings dam nearby. The higher pH may have been influenced by the disposal of the mill tailings. The mean herbaceous coverage ranged from 49.33 to 79.67 %. Soils from sites 5, 6, and 7 had significantly lower herbaceous coverage, and correspondingly their organic carbon and total N were lower (Table 1).
Soils from each site contained Pb, Zn, Cd, and Cu at levels that far exceeded pollution levels, according to The Environmental Quality Standards for Soils (GB 15618-1995, Table 1). The main metal pollutants were Pb, Zn, and Cd.
Metal concentrations in leaves
Heavy metal concentrations in leaves varied considerably among the species. Values of total Pb, Zn, Cd, and Cu of each species are given in Table 2. The highest Pb concentration (1,179.03 mg/kg) was found in leaves of a P. fortunei specimen at site 4, followed by B. papyrifera at site 8 (973.38 mg/kg). Notably, the Pb BCF of B. papyrifera was much higher (Fig. 2), reaching 0.701 elevated Pb concentration and BCF were also found in Amorpha fruticosa L., Quercus fabri Hance, and Symplocos paniculata (Thunb.) Miq. (Fig. 2).
Zn concentration in leaves was species-dependent. The highest value (1,968 mg/kg) was found in a Zenia insignis Chun specimen at site 3. P. fortunei at site 4, B. papyrifera and Vitex negundo var. heterophylla at site 8 also had significantly higher Zn concentrations in their leaves, ranging from 1,023 to 1,884 mg/kg (Table 2). These species showed relatively higher Zn BCF (Fig. 2) ranging from 0.503 to 0.946, which suggested that they are Zn accumulators. Notably, both the highest leaf Zn concentration and the highest BCF value were found in the same endemic species, Z. insignis. This species is nationally protected and is characterized by its root nodules and its rapid growth in poor-quality soils.
Leaf Cd concentration was highest in Z. insignis at site 3, ranging from 36.12 to 44.40 mg/kg (Table 2). Its mean BCF was 1.74, slightly lower than A. fruticosa at site 1 (12.58–44.16 mg/kg; BCF 2.04), Lagerstroemia indica L. at site 2 (16.21–26.65 mg/kg; BCF 2.05), and Robinia pseudoacacia L. at site 5 (15.84–18.22 mg/kg; BCF 2.02) (Table 2, Fig. 2). This suggested that this endemic species may also be a good Cd accumulator. The concentration of Cu was also analyzed. Compared with Pb and Zn, its concentration was substantially lower in the woody species investigated. The highest value (144 mg/kg) was found in a specimen of B. papyrifera (Table 2).
Comprehensive metal accumulation ability
By applying the CBCI to data for each species investigated, we found that B. papyrifera had the highest CBCI value (2.93), which was calculated as follows:
Where 0.07, 0.08, 0.16, and 0.13 are the minimum mean values of the BCF of Pb, Zn, Cd, and Cu, respectively, among the woody species investigated, and 0.61, 0.95, 2.15, and 0.70 are the maximum values of the BCF of Pb, Zn, Cd, and Cu, respectively. The B. papyrifera' mean BCF of Pb, Zn, Cd, and Cu are 0.61, 0.52, 1.11, and 0.67 (Table 2). Higher CBCI values are also found in the following woody species: A. fruticosa (2.72), L. indica (2.53), Z. insignis (2.44), Q. fabri (2.42), and P. fortunei (2.08). Their CBCI values were all >2.00 compared with other woody species we studied (Fig. 3). By comparison, the CBCI values of V. negundo var. heterophylla (0.27), Camellia oleifera Abel (0.10), and Cunninghamia lanceolata (Lamb.) H. (0.08) were much lower (Fig. 2).
Distribution of Pb, Zn, Cu, and Cd in tissues of B. papyrifera and P. fortunei
Metals have different distribution regularities in the tissues of trees we investigated. The highest concentration of Pb and Zn was found in older leaves of B. papyrifera and P. fortunei. By contrast, the highest concentration of Cu was found in the branches of the P. fortunei, relative to older leaves (Fig. 4). The functional leaves of P. fortunei had higher Cu levels than tender leaves and older leaves. On the contrary, the functional leaves of B. papyrifera had the lowest Cu concentration among the leaves of different ages (Fig. 4).
From Fig. 4, we can also see that the trunks of B. papyrifera and P. fortunei had the lowest metal concentration. A general trend was observed that Pb, Zn, Cd, and Cu concentrations increased from trunks to leaves (trunks < branches < leaves) except for Cu in P. fortunei. This increasing trend can also be found from trunks to fine roots (trunks < coarse roots < intermediate roots < fine roots) except for Cd in P. fortunei. Cd concentration in coarse roots is higher than fine and intermediate roots (trunks < intermediate roots < fine roots < coarse roots).
Discussion
Fast-growing, metal-accumulating tree species could be considered for phytoremediation practice (e.g., Pulford and Watson 2003; Puschenreiter et al. 2010). This is consistent with our results. The high heavy metal concentration in some adult trees presented in our study suggests that adult species such as B. papyrifera, P. fortunei, and Z. insignis accumulate a large amount of metals in their aerial tissues, particularly in leaves. This is an important finding for the long-term phytoremediation and further corroborates the feasibility of phytoremediation by trees, as it suggests that substantial heavy metal accumulation could be expected during a remediation period extending from seedlings to fully grown trees. The highest Pb concentration (1,179.03 mg/kg) was found in leaves of a P. fortunei specimen at site 4, which is more than the 1,000 mg/kg threshold of Pb hyperaccumulation plants (Baker et al. 2000). The highest Pb BCF (0.701) was found in B. papyrifera, a very high Pb BCF value in trees, and exceeds most public reports. The economic value of P. fortunei is high because of its wood and bio-fuel production due to its rapid growth and high biomass production. B. papyrifera is well known for its bark fibers, which are used for making paper, cloth, and rope. It is also notable for its extensive root system and tillers. Z. insignis belongs to a tall arbor tree species. It is characterized by its root nodules and has ecological value because of its fast growth in barren land. All these suggest that these species could be good choices for phytoextraction practice.
The fuzzy set theory was firstly introduced by L.A. Zadeh in 1965 (Zadeh 1996) and has been used in various areas. But even now, no attempts have been made to evaluate the metal accumulation capabilities of plants by this method. Here, we applied it in our study to assess the overall performance of the woody species in terms of multi-metal accumulation and proposed a CBCI. This index could synthesize accumulation results of several metal pollution factors into one relative measurement index. By comparing the CBCI value of each tree, the multi-metal accumulation abilities would be evaluated. The CBCI values in our study show that B. papyrifera and A. fruticosa had the highest multi-metal accumulation ability. This evaluation results are consistent with the findings of Seo (2008) and Shi (2011). When compared with R. pseudoacacia and Pinus densiflora grown in gold/silver abandoned mine soils and Pb/Zn abandoned mine soils, A. fruticosa had the best survival rate (Seo et al. 2008). The amount of heavy metals in the shoots of A. fruticosa was much higher than other species grown in copper and Pb/Zn mine tailings, reported Shi in 2011 (Shi et al. 2011). Higher CBCI values were also found in L. indica, Z. insignis, Q. fabri, and P. fortunei in our study. Paulownia has been introduced into the USA and Europe and is used for phytoremediation in recent years due to its elevated tolerance to high concentrations of metals, strong transpiration rates, rapid growth, and high biomass production (Doumett et al. 2008; Wang et al. 2009; Azzarello et al. 2012). Other woody species with higher CBCI values such as B. papyrifera, Z. insignis etc. should be given serious consideration for phytoremediation. The proposed CBCI would allow for the selection of suitable trees for phytoremediation in the future. To further test and refine the CBCI, and to understand more about heavy metal accumulation by trees, an extensive program of soil and leaf sampling from these and additional tree species is required.
Plant species, heavy metal concentrations in the environment, and other environmental factors could collectively influence the concentration of heavy metals in plants (Xue l et al. 2013). Large variations of metal concentration and BCF within the same species at different sites (Fig. 2) confirm this viewpoint. Although the woody species we investigated grew well at their sites, most had Pb and Zn leaf concentrations higher than 0.6–28 mg/kg (Pb) and 100–300 mg/kg (Zn) (Table 2); the critical toxicity levels for Pb and Zn in plants (Fasani 2012; Krämer 2010). Their Cd and Cu concentrations were also substantially higher than critical toxicity levels (6–10 mg/kg for Cd and 20–30 mg/kg for Cu) (Maestri et al. 2010; Fasani 2012) (Table 2). This may suggest that high metal concentration in the soil might have enhanced their metal tolerance and accumulation ability. Results from previous studies have shown similar trends. Populations from metal contaminated soils had greater tolerance than populations from normal soils, and their accumulation abilities differed (Bert et al. 2002). These variations may relate to genetic status because the frequency of multi-alleles and DNA quantity were significantly higher in populations from contaminated areas (Assunção et al. 2006; Basic et al. 2006). Gene number expansion may be used in the adaptation process for metal-contaminated environments (Puschenreiter et al. 2010), and could offer opportunities for further selection of specimens with high metal accumulation capabilities.
Different metals have different distribution regularities in tissues of trees. Cu concentration in the functional leaves of B. papyrifera was lower than in the tender leaves and older leaves, but larger in the functional leaves of P. fortunei (Fig. 4) compared with the tender and older leaves. The difference between the functional leaves of B. papyrifera and P. fortune confirms that metal accumulation mechanisms are various among tree species (Fernando et al. 2006; Hall 2002). With few exceptions, a general trend was noted in B. papyrifera and P. fortunei, namely that Pb, Zn, Cd, and Cu concentrations increased from trunks to leaves (trunks < branches < leaves) and from trunks to fine roots (trunks < coarse roots < intermediate roots < fine roots). The same trends were also found in Salix caprea and Populus tremula for Cd and Zn concentration (Unterbrunner et al. 2007) and in Holoptelia, Cassia, and Neem for Mn concentration (Raju et al. 2008). The large amount of heavy metal accumulated in the leaves or branches compared with the trunks meets the requirement of phytoextraction practice by trees. The harvesting could mainly target leaves and possibly young branches, especially for those metals that mainly contributed in branches, such as Cu in P. fortunei. The trunks are maintained to produce more branches and leaves, thus creating more biomass.
Conclusion
The results presented here reveal that the native species P. fortunei and B. papyrifera have large Pb accumulation potential and the endemic species Z. insignis has large Zn and Cd accumulation potential. Considering the combined pollution of the most contaminated soils, the CBCI proposed here will be of a certain practical value. It would help us finding more appropriate tree species with higher multi-metal accumulation ability, and increasing the phytoremediation efficiency. Data presented here reveal that B. papyrifera, A. fruticosa, L. indica, Z. insignis, Q. fabri, and P. fortunei have comprehensive higher metal accumulation abilities. The results are consistent with previous studies and provide a valuable source for the improvement of phytoremediation technology. In addition, A. fruticosa and L. indica belong to scrub species, and when grown with tall arbor tree and low herbaceous species, the efficiency of phytoremediation would be improved. Metal concentration higher in the leaves than in branches and trunks suggest that metal pollution might be moved through pulping management and harvesting. And our date also implied that metal accumulation characteristics were quite variable between individuals, which might offer families with high accumulation abilities for phytoremediation.
References
Assunção AG, Pieper B, Vromans J, Lindhout P, Aarts MG, Schat H (2006) Construction of a genetic linkage map of Thlaspi caerulescens and quantitative trait loci analysis of zinc accumulation. New Phytol 170:21–32
Azzarello E, Pandolfi C, Giordano C, Rossi M, Mugnai S, Mancuso S (2012) Ultramorphological and physiological modifications induced by high zinc levels in Paulownia tomentosa. Environ Exp Bot 81:11–17
Baker A, McGrath SP, Reeves RD, Smith J (2000) Metal hyperaccumulator plants: a review of the ecology and physiology of a biological resource for phytoremediation of metal-polluted soils. In: Terry N, Banuelos G (eds) Phytoremediation of contaminated soil and water. Lewis Publishers, Boca Raton, pp 85–107
Basic N, Salamin N, Keller C, Galland N, Besnard G (2006) Genetic differentiation of Thlaspi caerulescens natural populations in relation to their cadmium hyperaccumulation capacity. Biochem Syst Ecol 34:667–677
Bert V, Bonnin I, Saumitou-Laprade P, Laguérie P, Petit D (2002) Do Arabidopsis hallerifrom non-metallicolous populations accumulate zinc and cadmium more effectively than those from metallicolous populations? New Phytol 155:47–57
Bhargava A, Carmona FF, Bhargava M, Srivastava S (2012) Approaches for enhanced phytoextraction of heavy metals. J Environ Manage 105:103–120
Chen QZ, Timo S, John S (2012) Assessment of agri-environmental public goods provision using fuzzy Synthetic evaluation. Discussion papers, University of Helsinki, Department of economics and management. Number 61
Danh LT, Truong P, Mammucar R, Tran T, Foster N (2009) Vetiver grass, Vetiveria zizanioides: a choice plant for phytoremediation of heavy metals and organic wastes. Int J Phytoremediation 11:664–691
Di Lonardo S, Capuana M, Arnetoli M, Gabbrielli R, Gonnelli C (2011) Exploring the metal phytoremediation potential of three Populus alba L. clones using an in vitro screening. Environ Sci Pollut Res Int 18:82–90
Douay F, Roussel H, Pruvot C, Loriette A, Fourrier H (2008) Assessment of a remediation technique using the replacement of contaminated soils in kitchen gardens nearby a former lead smelter in Northern France. Sci Total Environ 401:29–38
Doumett S, Lamperi L, Checchini L, Azzarello E, Mugnai S, Mancuso S, Petruzzelli G, Del Bubba M (2008) Heavy metal distribution between contaminated soil and Paulownia tomentosa, in a pilot scale assisted phytoremediation study: influence of different complexing agents. Chemosphere 72(10):1481–1490
Fasani E (2012) Plants that hyperaccumulate heavy metals. In: Furini A (ed) Plants and heavy metals. Springer, Berlin Heidelberg, pp 55–74
Fernando DR, Bakkaus EJ, Perrier N, Baker AJ, Woodrow IE, Batianoff GN, Collins RN (2006) Manganese accumulation in the leaf mesophyll of four tree species: a PIXE/EDAX localization study. New Phytol 171:751–758
Garg A, Achari G, Joshi RC (2006) A model to estimate the methane generation rate constant in sanitary landfills using fuzzy synthetic evaluation. Waste Manag Res 24:363–375
Glass DJ (1999) U.S. and international markets for phytoremediation, 1999–2000. Industry Report. D. Glass Associates, Inc. Needham, Massachusetts, USA
Hall JL (2002) Cellular mechanisms for heavy metal detoxification and tolerance. J Exp Bot 53(366):1–11
Harada E, Hokura A, Nakai I, Terada Y, Baba K, Yazaki K, Shiono M, Mizuno N, Mizuno T (2011) Assessment of willow (Salix sp.) as a woody heavy metal accumulator: field survey and in vivo X-ray analyses. Metallomics 3(12):1340–1346
He WM, Ma FY (2000) Effects of water gradient on fluorescence characteristics and gas exchange in Sabina vulgaris seedlings. Acta Phytoecologica Sinica 24(5):630–634 (in Chinese)
He J, Ma C, Ma Y, Li H, Kang J, Liu T, Polle A, Peng C, Luo ZB (2013) Cadmium tolerance in six poplar species. Environ Sci Pollut Res 20(1):163–174
Khan S, Cao Q, Zheng YM, Huang YZ, Zhu YG (2008) Health risks of heavy metals in contaminated soils and food crops irrigated with wastewater in Beijing, China. Environ Pollut 152(3):686–692
Krämer U (2010) Metal hyperaccumulation in plants. Annu Rev Plant Bio 61:517–534
Liu XH, Gao YT, Sardar K, Duan G, Chen AK, Ling L (2008) Accumulation of Pb, Cu, and Zn in native plants growing on contaminated sites and their potential accumulation capacity in Heqing
Maestri E, Marmiroli M, Visioli G, Marmiroli N (2010) Metal tolerance and hyperaccumulation: costs and tradeoffs between traits and environment. Environ Exp Bot 68:1–13
Maric M, Antonijevic M, Alagic S (2013) The investigation of the possibility for using some wild and cultivated plants as hyperaccumulators of heavy metals from contaminated soil. Environ Sci Pollut Res 20(2):1181–1188
McGrath SP, Zhao FJ (2003) Phytoextraction of metals and metalloids from contaminated soils. Curr Opin Biotechnol 14:277–282
Mi C, Zhang X, Li S, Yang J, Zhu D, Yang Y (2011) Assessment of environment lodging stress for maize using fuzzy synthetic evaluation. Math Comput Model 54:1053–1060
Onkal-Engin G, Demir I, Hiz H (2004) Assessment of urban air quality in Istanbul using fuzzy synthetic evaluation. Atmos Environ 38:3809–3815
Pedron F, Petruzzelli G, Barbafieri M, Tassi E (2009) Strategies to use phytoextraction in very acidic soil contaminated by heavy metals. Chemosphere 75(6):808–814
Peuke AD, Rennenberg H (2005) Phytoremediation. Embo Rep 6:497
Pulford ID, Watson C (2003) Phytoremediation of heavy metal-contaminated land by trees—a review. Environ Int 29:529–540
Puschenreiter M, Türktaş M, Sommer P, Wieshammer G, Laaha G, Wenzel WW, Hauser MT (2010) Differentiation of metallicolous and non-metallicolous Salix caprea populations based on phenotypic characteristics and nuclear microsatellite (SSR) markers. Plant Cell Environ 33(10):1641–1655
Raju D, Sunil K, Urmil JM, Hazra S (2008) Differential accumulation of manganese in three mature tree species (Holoptelia, Cassia, Neem) growing on a mine dump. Curr Sci (Bangalore) 94:639–643
Sarma H (2011) Metal hyperaccumulation in plants: a review focusing on phytoremediation technology. J Environ Sci Tech 4:118–138
Seo KW, Son Y, Rhoades CC, Noh NJ, Koo JW, Kim JG (2008) Seedling growth and heavy metal accumulation of candidate woody species for revegetating Korean mine spoils. Restor Eco 16(4):702–712
Shi X, Zhang X, Chen G, Chen Y, Wang L, Shan X (2011) Seedling growth and metal accumulation of selected woody species in copper and lead/zinc mine tailings. J Environ Sci 23(2):266–274
Sun R, Shu F, Hao W, Li L, Sun WL (2011) Heavy metal contamination and Pb isotopic composition in natural soils around a Pb/Zn mining and smelting area. Environ Sci 32:1146–1153 (in Chinese)
Unterbrunner R, Puschenreiter M, Sommer P, Wieshammer G, Tlustoš P, Zupan M, Wenzel WW (2007) Heavy metal accumulation in trees growing on contaminated sites in Central Europe. Environ Pollut 148:107–114
Wang X, Jia Y (2010) Study on adsorption and remediation of heavy metals by poplar and larch in contaminated soil. Environ Sci Pollut Res Int 17(7):1331–1338
Wang J, Zhang CB, Jin ZX (2009) The distribution and phytoavailability of heavy metal fractions in rhizosphere soils of Paulownia fortunei (seem) Hems near a Pb/Zn smelter in Guangdong, PR China. Geoderma 148:299–306
Wei C, Wang C, Yang L (2009) Characterizing spatial distribution and sources of heavy metals in the soils from mining-smelting activities in Shuikoushan, Hunan Province, China. J Environ Sci 21:1230–1236
Xue l, Liu JF, Shi SQ, Wei Y, Chang EM, Gao M, Chen LZ, Jiang ZP (2013) Uptake of heavy metals by native herbaceous plants in an antimony mine (Hunan, China). ClEAN-soil, air, water. Accepted Articles
Zadeh LA (1996) Fuzzy sets, fuzzy logic and fuzzy systems: selected papers of Lotfi A. Zadeh. World Scientific Publishing, Singapore
Acknowledgments
This work was supported by the Ministry of Science and Technology, China (2011BAD0103 and 2012BAC09B03). The authors are grateful to Dr. Fang-Ping Tong and Zhen-Hua Liu at the Research Institute of Forestry, Hunan Academy of Forestry, China, for their continuous support during the experiment.
Author information
Authors and Affiliations
Corresponding author
Additional information
Responsible editor: Elena Maestri
Xiulian Zhao and Jianfeng Liu contributed equally to the article.
Rights and permissions
About this article
Cite this article
Zhao, X., Liu, J., Xia, X. et al. The evaluation of heavy metal accumulation and application of a comprehensive bio-concentration index for woody species on contaminated sites in Hunan, China. Environ Sci Pollut Res 21, 5076–5085 (2014). https://doi.org/10.1007/s11356-013-2393-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11356-013-2393-3