Abstract
The automatic width control of the strip that is used in vertical rolling is a key issue in the hot strip rolling process. It is the first time that the internal deformation power and the friction power are obtained by using angular bisector yield criterion and Pavlov projection principle in the vertical rolling. At the same time, the shear power is determined by use of the integral mean value theorem. Then the vertical rolling force and shape parameters are obtained by minimizing the total power functional. The relative error of rolling forces is less than 8.29 % compared with those measured on-line in a hot strip rolling plant. Moreover, the formula forms of the three powers mentioned above are greatly simplified and improved.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Xiong S, Rodrigues JMC, Martins PAF (2003) Three-dimensional modelling of the vertical–horizontal rolling process. Finite Elem Anal Des 39(11):1023–1037
Du XZ, Yang Q, Lu C, Wang AL, Kiet TA (2010) Optimization of short stroke control preset for automatic width control of hot rolling mill. J Iron Steel Res Int 17(6):16–20
Ginzburg VB (1989) Steel-rolling technology: theory and practice. Marcel Dekker, Inc., New York
Huisman HJ, Huetink J (1985) A combined Eulerian-Lagrangian three-dimensional finite-element analysis of edge-rolling. J Mech Working Technol 3(11):333–353
Xiong S, Liu X, Wang G, Zhang Q (1997) Simulation of slab edging by the 3-D rigid-plastic FEM. J Mater Process Technol 69(1-3):37–44
Xiong S, Liu X, Wang G, Martins PAF, Jiao S, Yuan J (2001) Three-dimensional thermo-mechanical finite element simulation of the vertical–horizontal rolling process. J Mater Process Technol 110(1):89–97
Xiong S, Liu X, Wang G, Zhang Q (2000) A three-dimensional finite element simulation of the vertical–horizontal rolling process in the width reduction of slab. J Mater Process Technol 101(1-3):146–151
Xiong S, Zheng G, Xianghua L, Wang G (2002) Analysis of the non-steady state vertical–horizontal rolling process in roughing trains by the three-dimensional finite element method. J Mater Process Technol 120(1-3):53–61
Xiong S, Liu X, Wang G, Zhang W (1997) Simulation of vertical horizontal rolling process during width reduction by full three dimensional rigid plastic finite element method. J Mater Eng Perform 6(6):757–76
Yun D, Lee D, Kim J, Hwang S (2012) A new model for the prediction of the dog-bone shape in steel mills. ISIJ Int 52(6):1109–1117
Luis CJ, Le´on J, Luri R (2005) Comparison between finite element method and analytical methods for studying wire drawing processes. J Mater Process Technol 164:1218–1225
Liu Y-M, Zhang D-H, Zhao D-W, Sun J (2015) Analysis of vertical rolling using double parabolic model and stream function velocity field. Int J Adv Manuf Technol. In press. doi: 10.1007/s00170-015-7393-7
Yu M, He L, Liu C (1992) Generalized twin-shear stress yield criterion and its generalization. Chin Sci Bull 37(24):2085–2089
Tresca H (1983) On the flow of solid bodies subjected to high pressures. Int J Mech Sci 25:71–74
Yu M (1983) Twin shear stress yield criterion. Int J Mech Sci 25(1):71–74
Zhao D (2012) The principle and application of integrating linearization for deformation power. Metallurgical Industry Press, Beijing (in Chinese)
Zhao D, Zhang S, Li C, Song H, Wang G (2012) Rolling with simplified stream function velocity and strain rate vector inner product. J Iron Steel Res 19(3):20–24
Павлов И. М (1950) Теория прокаткн. Металлургиэцат
Zhang SH, Zhao DW, Gao CR (2012) The calculation of roll torque and roll separating force for broadside rolling by stream function method. Int J Mech Sci 57(1):74–78
Klarin K, Mouton JP, Lundberg SE (1993) Application of computerized slip-linefield analysis for the calculation of the lever-arm coefficient in hot-rolling mills. J Mater Process Technol 36(4):427–446
Li H-j, Shi L-j, Xu J-z, Wang G-d (2009) Temperature model of hot strip finishing mills in tandem and its self-learning strategy. J Northeastern Univ (Natural science) 30(3):369–372
Moshitami (1969). Empirical formula of deformation resistance of carbon steel. Plastic Processing 10(97): 103-107
Zhang D-h, Cao J-z, Xu J-j, Peng W, Zhao D-w (2014) Simplified weighted velocity field for prediction of hot strip rolling force by taking into account flattening of rolls. J Iron Steel Res Int 21(7):637–634
Zhang D-H, Liu Y-M, Sun J, Zhao D-W (2015) A novel analytical approach to predict rolling force in hot strip finish rolling based on cosine velocity field and equal area criterion. Int J Adv Manuf Technol. In press. doi: 10.1007/s00170-015-7692-z
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Cao, J., Liu, Y., Luan, F. et al. The calculation of vertical rolling force by using angular bisector yield criterion and Pavlov principle. Int J Adv Manuf Technol 86, 2701–2710 (2016). https://doi.org/10.1007/s00170-016-8373-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-8373-2