Abstract
Water resources are essential to the ecosystem and social economy worldwide, especially in the desert and oasis of the Tarim River Basin, whose water originates largely from the Tianshan Mountains characterized by complicated hydrologic processes and scarce meteorological observations. In this study, distributed hydrologic model of SWAT (Soil and Water Assessment Tool) was applied to the Kaidu River Basin, a watershed in the Tianshan Mountains and one of the headwaters of the Tarim River. To quantify the contribution of meteorological input to model output, a sensitivity analysis approach (SDP method, State-Dependent Parameter method) was applied before and after the model was calibrated. The sensitivity analysis shows that meteorological input contributes up to 64 % of model uncertainty due to scarcity of observed meteorological data especially in the alpine region, and the groundwater flow is the most important hydrologic process in this watershed. Model calibration is robust with Nash–Sutcliffe coefficients (“NS”s) and “R 2”s over 0.80 for both the calibration period and the validation period where the length of the validation period is five times longer than the calibration period. The significance is obvious when compared to the simulation without considering the effect of spatial variation in meteorological input (NS = 0.80 and NS = 0.47 for “with lapse rates” and “without lapse rates”, respectively). Accurate meteorological input is of great importance to the distributed hydrological model, especially in the mountainous regions.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
The Tarim River (Fig. 1), the longest inland river in China, is suffering from the ecological degradation, which is caused by over-consumption of water and its special hydrological conditions (Chen et al. 2011; Liu et al. 2011). It mainly originates from the Tianshan Mountains, runs through the oasis and finally disappears in the desert. With critical ecological problems such as the drying of river channel, weak water reproducible ability, deterioration of groundwater quality, degradation of natural vegetation and desertification in recent decades, water is even crucial in the Tarim River Basin (Wu 2012; Li et al. 2014). As one of its headwaters, the Kaidu River, provides 78 % water demand of the artificial oasis around the Bosten Lake with a population of 1.15 million (Chen et al. 2013). Therefore, the Kaidu River is crucial to the eco-environmental and economic development of the lower reaches of the Tarim River.
In spite of the importance of this watershed, there are few studies focusing on hydrological process due to the complicated topographic features and data scarcity (e.g., few meteorological data) in the alpine area and almost no study on the impact of meteorological input. Most studies either focus on flow forecast (e.g., Kalra et al. 2013; de la Paix et al. 2012), conducting a short period of flow simulation (e.g., Huang et al. 2010; Dou et al. 2011), or simulations with lumped models (e.g., Yang et al. 1987). As these studies are limited in understanding the watershed hydrology, distributed hydrologic modeling with a long-term simulation is appealing. Furthermore, as there is a data scarcity in meteorological input, which is very crucial to hydrologic modeling (Bobba et al. 1999; Gourley and Vieux 2005), it is necessary to study the impact of meteorological input. More generally, though it has been proven that meteorological input influences the hydrologic model a lot (e.g., Tavakoli and De Smedt 2013), to our best knowledge, few papers deal with how much this influence is and how much it affects model calibration. This is the major goal of this paper.
To achieve this goal, distributed hydrologic model of SWAT (Arnold et al. 1998) was applied to this watershed. To handle a large number of distributed parameters and understand the impact of meteorological input, a sensitivity analysis approach which combines the Morris method (Morris 1991) and the SDP method (Ratto et al. 2007) was conducted to understand dominant hydrologic processes and quantify the effect of meteorological inputs on model calibration. The remaining is constructed as follows: Sect. 2 introduces the hydrologic model and study area; Sect. 3 describes the sensitivity analysis and calibration approaches; and then Sect. 4 gives results and discussion, followed by conclusions in Sect. 5.
Hydrologic model and study area
SWAT model
SWAT (Arnold et al. 1998), developed at the Agriculture Research Service of the United States Department of Agriculture, has been used for comprehensive modeling of the impacts of management practices and climate change on water and sediment yield and water quality at a watershed scale. It is a distributed hydrological model that runs on a daily step. To represent the spatial variability, a watershed is firstly divided into subbasins and each subbasin is then divided into hydrologic response units based on soil and landuse data. In SWAT, the simulation is based on water balance theory and runoff is predicted separately for each subbasin, which is illustrated in Fig. 2, and routed to obtain total runoff for the basin.
The climatic data required consists of daily precipitation, maximum/minimum air temperature, wind speed, relative humidity and solar radiation. SWAT uses elevation bands to represent the topographic effects on precipitation and temperature. Within each elevation band, the precipitation and temperature are estimated based on their lapse rates and elevation. For more details, refer to SWAT manuals (http://www.brc.tamus.edu/).
Study area and data collection
The Kaidu River Basin, with a drainage area of 18,634 km2 above the Dashankou hydrological station, is located on the south slope of the Tianshan Mountains, Northwest China. The basin extends from 82°58′ to 86°05′E, and from 42°14′ to 43°21′N (Fig. 1). The altitude ranges from 1340 to 4796 m above sea level (asl) with an average elevation of 2995 m and an average slope of 23 %. This watershed has a complex topography including grassland, marsh, and surrounding mountainous alpine areas (Dou et al. 2011).
This watershed is characterized as temperate continental climate with alpine climate characteristic. The average annual temperature at the Bayanbulak meteorological station is −4.16 °C and annual precipitation is 287 mm, and generally precipitation falls as rain from May to September each year and as snow from October to April of the next year. The average daily flow at the Dashankou hydrological station is around 110 m3 s−1 (equivalent to 185 mm runoff), ranging from 15 to 973 m3 s−1. Watershed hydrology is driven by snowmelt in spring and rainfall/snowmelt in summer. Data used in this study include:
Meteorological data and hydrologic data
Daily meteorological data of two stations are from China Meteorological Data Sharing Service System (http://cdc.cma.gov.cn/) from 1980 to 2010. One station is the Bayanbulak Station (2458 m asl), which lies in the valley of mountainous regions in the watershed, and the other is the Baluntai Station (1740 m asl), which is near the study region. Discharge data at the Dashankou hydrologic station are from Xinjiang Tarim River Basin Management Bureau. Available data include daily discharge from 1980 to 2002 and monthly discharge from 2003 to 2010.
Digital elevation model (DEM)
The 90 m DEM is from the Shuttle Radar Topography Mission (NASA, http://www2.jpl.nasa.gov/srtm/). DEM forms the basis for determining the drainage area, flow direction, basin boundary, etc.
Soil data
Soil map, with a scale of 1:1000,000 is from Xinjiang Institute of Ecology and Geography, Chinese Academy of Sciences. The spatial distribution of soil is shown in Fig. 3 (top) and the corresponding proportions are listed in Table 1 (left). Soil texture, soil depth and other information of each soil type were from Agricultural bureau and soil survey office of Xinjiang (1996).
Landuse data
Landuse map with a scale of 1:100,000 is from the Environmental and Ecological Science Data Center for West China. Spatial distribution of landuse type is shown in Fig. 3 (bottom) and relevant proportions are listed in Table 1 (right).
Model setup and initial parameter selection
After pre-processing these data in ArcSWAT (swat.tamu.edu/software/arcswat/), the SWAT model (version 2009) was set up with the following options: (1) Elevation band and lapse rate were used to represent the topographic effects on precipitation and temperature in the mountainous region; (2) Penman–Monteith method (Monteith 1965) was utilized to calculate potential evapotranspiration; (3) The degree-day approach, which is generally deemed as an effective method to handle snow pack and snowmelt in data scarce mountains (Li and Williams 2008), was used to model snowmelt; (4) Variable storage routing method (Williams 1969) was used for river routing.
Model parameters related to flow simulation were initially selected based on literature review and SWAT user manual (Arnold et al. 2011). When calibrating distributed model parameters, a factor which denotes a way to change a group of parameters was used to avoid confusion with model parameters (e.g., factor r__CN2 is to relatively change all distributed parameters CN2, and v__Tlaps is to replace all parameters Tlaps), as proposed in Yang et al. (2007). Table 2 lists these factors along with their meanings of their underlying parameters and ranges, among which v__Tlaps and v__Plaps, the values of the lapse rates of temperature and precipitation, are two factors to measure the topographical variation of meteorological input. This work studied the contribution of meteorological input through these two factors. To investigate the impact of spatial variation of meteorological input, another simulation was set up without these two lapse rates (i.e., excluding v__Tlaps and v__Plaps), and refer this to “without lapse rates” and the previous to “with lapse rates”, respectively.
A warm-up period is normally used to eliminate the influence of initial state variables (e.g., soil moisture, groundwater storage, etc.) on simulation, and the longer the warm-up period, the less effect initial state variables will have on the simulation (Yang et al. 2012). In this study, a seven-year period (1979–1985) was used for model warm-up after some tests. To calibrate the model, the split sample procedure was used: daily data from 1986 to 1989 were used for model calibration, and daily data from 1990 to 2002 (first validation period) and monthly data from 2003 to 2010 (second validation period) were used to test the model performance. Both calibration and validation contain dry and wet years, and longer validation period was used to show the robustness of the calibrated model.
Methodology
Sensitivity analysis
Sensitivity analyses are valuable tools for identifying important model parameters (in this case is “factors”). In this study, a sensitivity analysis approach combining the Morris method (Morris 1991) and the SDP method (Ratto et al. 2007) was applied to screen out unimportant factors and identify the most important ones. Its applications range from simple conceptual model (e.g., HYMOD in Yang 2011) to physical and distributed models (e.g. TOPMODEL in Ratto et al. 2007; Wetspa in Yang et al. 2012; MOBIDIC in Yang et al. 2014), and it has been proven to be effective and efficient. Firstly the Morris method was used to screen out insensitive hydrological factors and thus to reduce the number of factors for next sensitivity analysis. In the second step, the SDP was implemented to quantitatively compute the main effect and first-order interactions between these reduced factors.
Morris method
The Morris method is a qualitative method to measure factor sensitivity and factor interaction or nonlinearity. For a n-dimensional random variable \(X = (x_{1} , \ldots ,x_{i} , \ldots ,x_{n} )\) at its jth sample\((x_{1j} , \ldots ,x_{ij} , \ldots ,x_{nj} )\), the local sensitivity measure (elementary effect) d ij for x i at jth sample is computed based on OAT (One-At-a-Time) as follows:
where f(.) is the model output (or relevant objective function), X are model factors with x i normalized to [0,1] to eliminate the scale effect, and \(\Delta = \frac{p}{2(p - 1)}\) is the predefined increment and normally p takes the value within the range of [4,10] (Saltelli 1999) and in this study p was set to 10 meaning ∆ = 5/9. Local sensitivity measures of each input factor are estimated by randomly sampling in the factor space, by which a finite distribution of the local sensitivity measures obtained. For example, for basic sample size m, one can obtain a group of elementary effects d ij (i = 1,…, m) for factor x i . From these values, two statistics are obtained: one is the mean of absolute values of the elementary effects (\(\mu^{*}\)), which measures the factor sensitivity (e.g., for x i , \(\mu_{i}^{*} = \mathop \sum \nolimits_{j = 1}^{m} {{\left| {d_{ij} } \right|} \mathord{\left/ {\vphantom {{\left| {d_{ij} } \right|} m}} \right. \kern-0pt} m}\)), and the other is the standard deviation of the elementary effects (\(\sigma\)), which measures the degree of factor interaction or nonlinearity (e.g., for x i , \(\sigma_{i} = \sqrt {{{\mathop \sum \nolimits_{j = 1}^{m} \left( {d_{ij} - \frac{{\mathop \sum \nolimits_{j = 1}^{m} d_{ij} }}{m}} \right)^{2} } \mathord{\left/ {\vphantom {{\mathop \sum \nolimits_{j = 1}^{m} \left( {d_{ij} - \frac{{\mathop \sum \nolimits_{j = 1}^{m} d_{ij} }}{m}} \right)^{2} } {(m - 1)}}} \right. \kern-0pt} {(m - 1)}}}\). The higher \(\mu^{*}\) is, the more important the factor is to model output, and the higher (\(\sigma\)), the more interactions are with other factors or more nonlinear to the model output. Totally, the Morris method needs m*(n + 1) model runs to estimate these two sensitivity indices for each factor, and normally m = 50 is sufficient (Yang et al. 2012).
State-dependent parameter method (SDP)
For independent input factors, SDP method is based on the idea of the decomposition of variance of model output Y to factors X:
where,
and so on. Herein, V(.) and E(.) denote variance and expectation operators, V is the total variance, and V i and V ij are total variance and partial variances of the ith factor. Normalize these variances with V, the following sensitivity indices can be obtained:
where S i is the main effect, which represents the average achieved reduction of output variance when factor X i is fixed, S ij is the second-order interaction between X i and X j , and S Ti is the total effect representing the average output variance when X i stays unfixed. In practice, S i is used to measure the average variance in the output that can be reduced when X i is fixed and S Ti is used to measure the average variance in the output remains when X i stays unfixed (Tarantola et al. 2002).
The SDP method is based on recursive filtering and smoothing estimation and can estimate these main effects (S i ) and first-order interactions (S ij ) based on its approximation to second-order ANOVA regression model. And “quasi-total effect”, \(S_{Di} = S_{i} + \varSigma_{j} S_{ij}\), is used to approximate S Ti when R 2 of second-order ANOVA is high enough (e.g., larger than 0.80).
Model calibration and evaluation
To calibrate the distributed hydrological model, SCE-UA method (Duan et al. 1992) was used. This algorithm has been proven to be consistent, effective, and efficient in locating the globally optimal model parameters of a hydrologic model (Gupta et al. 1999).
The objective function for calibration is Nash–Sutcliffe coefficient (NS) (Nash and Sutcliffe 1970):
where \(Y_{i}^{\text{obs}}\) and \(Y_{i}^{\text{sim}}\) are the ith observed and simulated flows, \(Y^{\text{mean}}\) is the mean of observed data, and n is the number of observations. NS donates how well the simulation matches the observation. NS ranges between −∞ and 1.0, with NS = 1 meaning a perfect fit. The higher this value, the more reliable the model is.
To evaluate model performance, in addition to NS, percent bias (PBIAS) and coefficient of determination (R 2) were also used. PBIAS is computed as:
PBIAS measures the average deviation of the simulated data from their observed counterparts. Positive values indicate an overestimation of the observation, while negative values indicate an underestimation. The smaller of \(\left| {PBIAS} \right|\), the smaller deviation of the simulation. Generally, \(\left| {\text{PBIAS}} \right|\) < 10 % shows good modeling. R2 describes the degree of collinearity between simulated and measured data. Normally NS > 0.50, \(\left| {\text{PBIAS}} \right|\) < 25 % and R 2 > 0.6 are taken as the criteria of satisfactory modeling of the river discharge, and model performance can be evaluated as excellent if NS > 0.75 and \(\left| {PBIAS} \right|\) < 10 % (Moriasi et al. 2007).
In this study, the simulation “with lapse rates” and simulation “without lapse rates” were analyzed separately following the same procedure. Firstly, the Morris method was applied to initially selected factors (Table 2) to screen out the unimportant factors, and then the sensitivities of the sensitive ones were quantified by the SDP method. Secondly, the calibration was applied to the important factors, followed by another sensitivity analysis with the SDP method. The contribution of the meteorological input was analyzed based on the sensitivity and calibration results, and the comparison between the simulation “with lapse rates” and simulation “without lapse rates”.
Results and discussion
In this section, we mainly presented and discussed the result of the simulation “with lapse rates”, and the result of simulation “without lapse rates” was only for the comparison purpose. Hereafter, results and discussion are based on the simulation “with lapse rates” unless otherwise specified.
Sensitivity analysis
With m = 50, the Morris method took 1300 model runs. Figure 4 shows the sensitivity result for each factor based on the Morris method, where \(\mu^{*}\) represents its sensitivity and \(\sigma\) its interaction with other factors or nonlinearity of the factor. These twenty-five factors were grouped into three classes visually based on their “\(\mu^{*}\)”s: extremely sensitive, medially sensitive and insensitive. v__Tlaps, v__Alpha_bf and v__Plaps are the extremely sensitive factors with strong nonlinearity in the meanwhile. v__Tlaps and v__Plaps influence the temperature and precipitation input in each elevation band, and have intense impact on water yield and water balance. v__Alpha_bf, representing the baseflow recession constant, describes the response of groundwater to recharge change and is an important factor that influences groundwater flow. The medium sensitivity class includes 7 factors: v__Gwqmn and v__Gw_delay are factors related to groundwater flow and groundwater–stream water interactions; v__Ch_k2, r__Sol_k and r__Sol_awc dominate the infiltration of surface water into groundwater; v__Esco, with its underlying parameter Esco being the compensation factor of soil evaporation, controls the actual evapotranspiration; r__Slsubbsn is factor indicating the changes of average slope length. Factors at the bottom left of Fig. 4 including r__CN2 and v__Smfmx are insensitive. Note that r__CN2 is not sensitive in this study while it was extremely sensitive in many previous studies (e.g., Van Griensven et al. 2006; Saha et al. 2014). This might be attributed to the hydrological characteristics of the Kaidu River Basin: it has a large area of wetland (1137 km2) and flatland (37 % of the study area with a slope under 8.7 %). The high proportion of wetland and flatland resulted in the low sensitivity of r__CN2 as identified by Schmalz et al. (2009). All snowmelt-related factors, e.g., v__Smfmx, v__Sftmp, v__Smtmp, are not sensitive, which indicates that snow process is not so important in the Kaidu River Basin. This is corroborated with an analysis of average monthly precipitation allocation: the precipitation from October to March (winter season) only consists of 9 and 4 % of the yearly precipitation at Bayanbulak and Balutai, respectively.
After excluding insensitive factors identified by the Morris method, the SDP method was applied to estimate the main effect (S i ) and first-order interaction (S ij ) of the sensitive factors. To ensure that all potential sensitive factors are quantified, another two factors, i.e., r__CN2 and v__Smfmx, the most sensitive ones in the insensitive group, were also included. Therefore, 12 factors were analyzed using SDP method. It took 600 model runs and the R2 of the second-order ANOVA model is 93.0 %, which means it explains over 90 % of the model uncertainty (i.e., variation of NS). The result is shown in Table 3. The most sensitive factor is v__Tlaps, followed by v__Plaps and v__Alpha_bf. Other factors are not so sensitive for both S i and S Di . v__Tlaps and v__Plaps control the driving force (i.e., precipitation and temperature), and the main effect of these two factors is 64.0 % (i.e. sum of main effects of v__Tlaps and v__Plaps, and their first-order interaction), contributing to over half of the model uncertainty. v__Alpha_bf influences the groundwater flow and its main effect is 13 %. This suggests that fixing of these three factors (e.g. through calibration) leads to over 77 % reduction of model uncertainty. This result is the same as that based on the Morris method. It is worth noting that the low sensitivity indices of other factors do not mean that they are not sensitive but that their contribution to the model output is not as significant as these three factors.
Model calibration and evaluation
Calibration was then carried out on these twelve factors using SCE-UA method. With daily NS = 0.80 during the calibration period, the optimal values are given in Table 2. The calibrated v__Plaps is 165 mm km−1, which is very close to other studies in this region (e.g., 162 mm km−1 in Lin 1985; 156.4 mm km−1 in Zhao et al. 2011). v__Tlaps is −9.23 °C km−1, within the range of the study of Chen (2012) (i.e., from −11.8 to −7.3 °C km−1) based on temperature data from several stations in the south slope of Tianshan Mountains. This temperature lapse rate, which is close to the dry adiabatic lapse rate (−9.8 °C km−1), is related to the characteristics of our study region, i.e., a mountainous watershed located in the arid area with low pressure, low humidity and high wind speed (e.g., Blandford et al. 2008). The mean pressure and relative humidity are 0.828 × 105 Pa and 42 % at Baluntai Station, and 0.758 × 105 Pa and 69 % at Bayanbulak Station. Besides, there are over 12 % of days with wind speed higher than 5 m s−1 (strong wind) and 38 % of days higher than 3 m s−1 (moderate to strong wind) at Bayanbulak Station.
As discussed above, the hydrologic response is dominated by the meteorological input. By fixing two factors v__Tlaps and v__Plaps to their optimal values, another SDP application was performed to the remaining ten factors to study the important hydrologic processes without the influence of meteorological input. As it turns out, the most sensitive factors are v__Alpha_bf (S i = 0.57) and v__Gw_delay (S i = 0.29), less sensitive factors are r__Sol_k (S i = 0.02) and v__Smfmx (S i = 0.02) and other factors are only sensitive through the interaction with these factors. Factors related to groundwater process (i.e. v__Alpha_bf, v__Gw_delay) account for more than 80 % of the model uncertainty (sum of main effects of these two factors and first-order interactions between them). Although by the Morris method, v__Smfmx is an insensitive factor, it is a relatively sensitive one by the SDP method when fixing v__Tlaps and v__Plaps. It is indicative that the dominant hydrological process is the groundwater flow, and then the snowmelt flow and evapotranspiration. To verify the importance of groundwater, a baseflow separation was done to the observed discharge using the digital filter technique (Arnold et al. 1995), which shows that groundwater contributes to 72–86 % of the total flow (or runoff). The high percentage of groundwater might be due to the large flat valley area between steep mountains, i.e., large area of wetland and flatland as is indicated in Sect. 4.1.
Table 4 and Fig. 5 show agreement between the simulated and observed flow series. As indicated by the statistics in Table 4, the model performs well for both the calibration period (1986–1989) and validation periods (first validation period 1990–2002 and second validation period 2003–2010), in spite of the length of the validation period is five times longer than the calibration period. The “NS”s, “PBIAS”s, “R 2”s are 0.80, 0.01 %, 0.80 for the calibration period, 0.81, 2.94 %, 0.81 for the first validation period, and 0.86, 1.31 %, 0.87 for the second validation period. These “NS”s, “PBIAS”s, and “R 2”s are within the excellent range proposed by Moriasi et al. (2007).
The statistics above are corroborated by Fig. 5. In Fig. 5, the simulated flow matches the observation very well except for some peaks in summer seasons in 1987, 1999 and 2002. This might be due to the glacier melt in summer which is not accounted for in this model. Generally, the model can simulate the flow response to the rainfall and snowmelt. Notice there is a fluctuation in the baseflow since 1992 when the Dashankou hydropower station (4 km above the Dashankou hydrological station) started to operate. However, this hydropower station does not seem to have too much effect on the daily outflow.
To demonstrate the effect of the meteorological input, the results of the simulation “without lapse rates” are also shown in Table 4 and Fig. 5a. Compared to simulation “with lapse rates”, simulation “without lapse rates” was unable to capture most of the discharges in the Kaidu River Basin, with NS equals to 0.47 for the calibration period, 0.49 for the first validation period and 0.35 for the second validation period. Snowmelts in spring (e.g., in 1986, 1987 and 1989) were underestimated, peaks in summer (e.g., in 1988) were not captured, and baseflow was extremely underestimated. For “without lapse rates”, the underestimation of the baseflow is mainly related to over-simplification of spatial distribution of precipitation and temperature. As a result, this leads to less average annual precipitation (252 mm) and higher average temperature (5.1 °C) than these of “with lapse rate” whose average annual precipitation is 378 mm and average temperature is −1.9 °C. When driving the hydrologic model, it will cause less precipitation input and higher evapotranspiration, and this leads to less groundwater recharge, and eventually less groundwater discharge. Figure 6 shows how different the spatial variation of annual average precipitation using precipitation lapse rate (Fig. 6a) from the one without precipitation lapse rate (Fig. 6b). This shows the importance of spatial variation of meteorological input in calibrating a distributed hydrological model and confirms the conclusion that high quality of distributed rainfall data contributes to good hydrological model performance (Tavakoli and De Smedt 2013; Lee et al. 2013).
Conclusions
This paper implemented a combined sensitivity analysis approach to the application of SWAT in the Kaidu River Basin to investigate the contribution of meteorological input in calibrating distributed hydrologic model. The following conclusions can be drawn:
-
1.
Our model is an effective tool to simulate the hydrologic processes. Simulated daily flow series are in agreement with the observed ones, with “NS”s and “R 2”s over 0.80 and |PBIAS| < 3 % for both calibration period and validation period. This calibration is robust and tested by the validation period whose length is five times longer than the calibration period.
-
2.
Sensitivity analysis shows v__Tlaps and v__Plaps are the two most important factors with main effects of 64.0 %. This indicates the model uncertainty largely results from the meteorological inputs due to the scarcity of observed meteorological data, especially in the alpine regions.
-
3.
Groundwater flow is the most important hydrologic process in this watershed. Fixing v__Tlaps and v__Plaps to their optimal values, factors related to groundwater process account for over 80 % of the model uncertainty, which is consistent with the result of baseflow separation using digital filter technique.
-
4.
Compared to the simulation “without lapse rates”, the simulation “with lapse rates” shows significant improvement on daily flows, especially in baseflow simulation (groundwater discharge), which suggests high spatial resolution meteorological data (e.g., satellite data) should be used for hydrologic modeling in this region.
References
Agricultural bureau and soil survey office of Xinjiang (1996) Xinjiang soil. Science Press, Beijing
Arnold JG, Allen P, Muttiah R, Bernhardt G (1995) Automated base flow separation and recession analysis techniques. Ground Water 33:1010–1018
Arnold JG, Srinivasan R, Muttiah RS, Williams J (1998) Large area hydrologic modeling and assessment part I: model development. J Am Water Resour As 34:73–89
Arnold JG, Kiniry J, Srinivasan R, Williams J, Haney E, Neitsch S (2011) Soil and Water Assessment Tool input/output file documentation, version 2009
Blandford TR, Humes KS, Harshburger BJ, Moore BC, Walden VP, Ye H (2008) Seasonal and synoptic variations in near-surface air temperature lapse rates in a mountainous basin. J Appl Meteorol Clim 47:249–261
Bobba AG, Jeffries DS, Singh VP (1999) Sensitivity of hydrological variables in the Northeast Pond River watershed, Newfoundland, Canada, due to atmospheric change. Water Resour Manag 3:171–188
Chen X (2012) Hydrological model of inland river basin in arid land. China Environmental Science Press, Beijing
Chen Z, Chen Y, Li W, Chen Y (2011) Changes of runoff consumption and its human influence intensity in the mainstream of Tarim river. Acta Geogr Sin 66:89–98
Chen Y, Du Q, Chen Y (2013) Sustainable water use in the Bosten Lake Basin. Science Press, Beijing
De la Paix MJ, Li LH, Ge JW, de Dieu HJ, Theoneste N (2012) Analysis of snowmelt model for flood forecast for water in arid zone: case of Tarim River in northwest China. Environ Earth Sci 66:1423–1429
Dou Y, Chen X, Bao A, Li L (2011) The simulation of snowmelt runoff in the ungauged Kaidu River Basin of TianShan Mountains, China. Environ Earth Sci 62:1039–1045
Duan Q, Sorooshian S, Gupta V (1992) Effective and efficient global optimization for conceptual rainfall-runoff models. Water Resour Res 28:1015–1031
Gourley JJ, Vieux BE (2005) A method for evaluating the accuracy of quantitative precipitation estimates from a hydrologic modeling perspective. J Hydrometeorol 6:115–133
Gupta HV, Sorooshian S, Yapo PO (1999) Status of automatic calibration for hydrologic models: comparison with multilevel expert calibration. J Hydroaul Eng 4:135–143
Huang Y, Chen X, Li Y, Willems P, Liu T (2010) Integrated modeling system for water resources management of Tarim River Basin. Environ Eng Sci 27:255–269
Kalra A, Li L, Li X, Ahmad S (2013) Improving streamflow forecast lead time using oceanic-atmospheric oscillations for Kaidu River Basin, Xinjiang, China. J Hydrol Eng 18:1031–1040
Lee G, Yu W, Jung K (2013) Catchment-scale soil erosion and sediment yield simulation using a spatially distributed erosion model. Environ Earth Sci 70:33–47
Li X, Williams MW (2008) Snowmelt runoff modelling in an arid mountain watershed, Tarim Basin, China. Hydrol Process 22:3931–3940
Li Q, Zhou JL, Zhou YZ, Bai CY, Tao HF, Jia RL, Ji YY, Yang GY (2014) Variation of groundwater hydrochemical characteristics in the plain area of the Tarim Basin, Xinjiang Region, China. Environ Earth Sci 72:4249–4263
Lin R (1985) Characteristics on the vertical distribution of precipitation and runoff in the south slope of the Tianshan Mountain. Hydrology 2:28–33
Liu T, Willems P, Pan XL, Bao AM, Chen X, Veroustraete F, Dong QH (2011) Climate change impact on water resource extremes in a headwater region of the Tarim basin in China. Hydrol Earth Syst Sci 15:3511–3527
Monteith JL (1965) Evaporation and environment. Symp Soc Exp Biol 19:205–234
Moriasi DN, Arnold JG, Van Liew MW, Bingner RL, Harmel RD, Veith TL (2007) Model evaluation guidelines for systematic quantification of accuracy in watershed simulations. T Asabe 50:885–900
Morris MD (1991) Factorial sampling plans for preliminary computational experiments. Technometrics 33:161–174
Nash JE, Sutcliffe J (1970) River flow forecasting through conceptual models part I—A discussion of principles. J Hydrol 10:282–290
Ratto M, Young PC, Romanowicz R, Pappenberger F, Saltelli A, Pagano A (2007) Uncertainty, sensitivity analysis and the role of data based mechanistic modeling in hydrology. Hydrol Earth Syst Sci 11:1249–1266
Saha P, Zeleke K, Hafeez M (2014) Streamflow modeling in a fluctuant climate using SWAT: Yass River catchment in south eastern Australia. Environ Earth Sci 71:5241–5254
Saltelli A (1999) Sensitivity analysis: could better methods be used? J Geophys Res 104:3789–3793
Schmalz B, Fohrer N (2009) Comparing model sensitivities of different landscapes using the ecohydrological SWAT model. Adv Geosci 21:91–98
Tarantola S, Giglioli N, Jesinghaus J, Saltelli A (2002) Can global sensitivity analysis steer the implementation of models for environmental assessments and decision-making? Stoch Environ Res Risk Assess 16:63–76
Tavakoli M, De Smedt F (2013) Validation of soil moisture simulation with a distributed hydrologic model (WetSpa). Environ Earth Sci 69:739–747
Van Griensven A, Meixner T, Grunwald S, Bishop T, Diluzio M, Srinivasan R (2006) A global sensitivity analysis tool for the parameters of multi-variable catchment models. J Hydrol 324:10–23
Williams J (1969) Flood routing with variable travel time or variable storage coefficients. Trans ASAE 12:100–103
Wu J (2012) Evaluation of the water resource reproducible ability on Tarim River Basin in south of Xinjiang, northwest China. Environ Earth Sci 66:1731–1737
Yang J (2011) Convergence and uncertainty analyses in Monte-Carlo based sensitivity analysis. Environ Modell Softw 26:444–457
Yang X, Jiang H, Huang C (1987) An applied study on the snowmelt type of Xinanjiang Watershed Model at the Kaidu River Baisn. J August 1st Agri Collage 4:82–90
Yang J, Reichert P, Abbaspour KC (2007) Bayesian uncertainty analysis in distributed hydrologic modeling: a case study in the Thur River basin (Switzerland). Water Resour Res 43:W10401
Yang J, Liu Y, Yang W, Chen Y (2012) Multi-objective sensitivity analysis of a fully distributed hydrologic model WetSpa. Water Resour Manag 26:109–128
Yang J, Castelli F, Chen Y (2014) Multiobjective sensitivity analysis and optimization of distributed hydrologic model MOBIDIC. Hydrol Earth Syst Sci 18:4101–4112
Zhao C, Shi F, Sheng Y, Li J, Zhao Z, Han M, Yilibula Y (2011) Regional differentiation characteristics of precipitation changing with altitude in Xinjiang region in recent 50 years. J Glaciol Geocryol 6:1203–1213
Zhou Y (1999) Xinjiang river hydrology and water resources. Xinjiang Science and Technology Press, Urumqi
Acknowledgments
The research was supported by the “Thousand Youth Talents” Plan (Xinjiang Project: Y371051), the National Natural Science Foundation of China (41471030) and the Foundation of State Key Laboratory of Desert and Oasis Ecology (Y371163).
Conflict of interest
The authors declare that they have no conflict of interest.
Ethical approval
This article does not contain any studies with human participants or animals performed by any of the authors.
Informed consent
Informed consent was obtained from all individual participants included in the study.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Fang, G., Yang, J., Chen, Y. et al. Contribution of meteorological input in calibrating a distributed hydrologic model in a watershed in the Tianshan Mountains, China. Environ Earth Sci 74, 2413–2424 (2015). https://doi.org/10.1007/s12665-015-4244-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12665-015-4244-7