The fatigue life prediction and reliability analysis of dynamic systems under random excitement are important topics in modern engineering design. However, the stress power spectra density of a component in a dynamic system must be known when one predicts its fatigue life and analyzes its reliability. With the rapid development of computer technology and numerical computation theories, it has been possible to simulate stress power spectra density of dynamic systems. Based on this, a method of simulating computation for the fatigue life prediction of a dynamic structure is presented. It depended on some simulating equations of the stress power spectra density of the structure and the fatigue life prediction which was obtained in this paper. By this way, as an example, the virtual design of the fatigue life and reliability analysis for the CW-200k vehicle truck was developed. The method is suitable not only for the running dynamic structure but also for newly designed structures.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction. The fatigue life prediction and reliability analysis of dynamic systems under random excitement are important topics in modern engineering design [1–8]. The vibration characteristics of fatigue damage of beam-type structural components has been researched [9, 10] and a computational and experimental assessment of the sensitivity of structural materials to stress concentration under high-cycle asymmetrical loading has been performed [11]. A numerical calculation of the frequencies of natural vibrations of beams with a cross section varying linearly in height under different conditions of fixing their ends is presented [12]. However, the stress power spectral density of a component in a dynamic system must be known when one predicts its fatigue life and analyzes its reliability. A traditional way is to measure the stress power spectral density, which has played an important role in practice [4]. However, the stress power spectral density of a dynamic system will change with the alteration of the structure and dynamic parameters of a system. So the engineering application in this way is limited. Moreover, one is not able to obtain the stress power spectral density of a new dynamic system before it has been designed. With the rapid development of computer technology and numerical computation theories, it has been possible to simulate stress power spectral density of dynamic systems. Based on this, the method of simulating stress power spectral density is put forward in this paper, and as an example the fatigue life prediction and reliability analysis of CW-200k [4] vehicle truck are made.
Computational Method of Stress Power Spectral Density.
Random Response Spectra of Dynamic System Computation [1, 2]. In general, the vibration equation of a linear system can be written in matrix form as
where M, C, and K are N × N symmetric matrices representing the masses, damping, and stiffness of the system, \( \ddot{z}(t),\dot{z}(t),\;\mathrm{and}\;z(t) \), and z(t ) are column vectors representing acceleration, velocity, and displacement, respectively, and F(t ) is matrix of excitation function.
From Eq. (1), the frequency response matrix is obtained by taking the Fourier transform as follows [3]:
where H(ω) = F (z(t ) F (F(t )).
Therefore, the power spectral density matrix of system can be deduced as
where H* T(ω) is conjugate transpose matrix of H (ω) and G x (ω) is input power spectral density matrix of a system.
If the time difference τ exists in the excitation process, according to the time difference property of the Fourier transform, G x (ω) may be expressed as
Similarly, the acceleration amplitude of the system response is given by
The Unit Load Stress Matrix Computation. In a linear elastic system, the stress state of the structure may be expressed as
where S(x, y, z) is defined as unit load stress matrix. Vector b(t ) is the load state vector. The load state vectors may be expressed as
where F(t) = (F1(t), F2(t), …, F n (t)) is called the forces in the translation sense, M(t) = (M1(t), M2(t), …, M n (t)) is called the moments in rotation, J = (W, V)T is called linear operator or coefficients’ matrix, and z(t ) is vector representing the response of each degree of freedom.
According to the theory of correlation function [3], the correlation function matrix of stress state of stationary random process can be written as
where E represents mathematical expectation.
Therefore, the stress power spectral density matrix can be obtained by taking Fourier transform as
Then the stress square deviation is
If z(t) = [z 1(t), z 2(t), …, z n (t)] represents response vector matrix of a system, then the response spectra will be of the form
Now, the relationship between the response spectra of the system and stress power spectral density of a structure is established. Based on this formulation, one is able to estimate fatigue life and analyze the reliability of the structure.
The Fatigue Life Prediction of the CW-200k type Truck.
The Stress Power Spectral Density Computation of the CW-200k Type Truck of a Passenger Vehicle. The stress power spectral density of the frame of a truck can be researched in the vertical vibration of six-degreeof-freedom system because, in high-speed railways, track is either straight or has a big radius. The dynamic model of vehicle is as shown in Fig. 1.
The equations of motion was obtained as follows:
and Eqs. (12) are written in matrix form as
where {z} is displacement vector, \( \left\{z\right\}={\left[\begin{array}{llllll}{z}_c\hfill & {\upvarphi}_c\hfill & {z}_{b1}\hfill & {\upvarphi}_{b1}\hfill & {z}_{b2}\hfill & {\upvarphi}_{b2}\hfill \end{array}\right]}^T,\kern1em \left\{\upeta \right\} \) is the input vector, \( \left\{\upeta \right\}={\left[\begin{array}{llll}{\upeta}_1\hfill & {\upeta}_2\hfill & {\upeta}_3\hfill & {\upeta}_4\hfill \end{array}\right]}^T,\kern1em \left[M\right],\kern1em \left[C\right],\kern1em \mathrm{and}\kern1em \left[K\right] \) are 6×6 symmetric matrices representing the mass, damping, and stiffness of a vehicle system, respectively, and [C η] and [K η] are matrices of coefficients. They correspond to the CW-200k type truck and 25 type passenger rail vehicle.
The expression for the track spectrum is given by [4]
The track spectrum was provided by the Office for Research and Experiments of the International Union of Railways (ORE B176), the high level ORE parameters are as follows: Ω c = 0.8246 rad/m, Ω r = 0.0206 rad/m, and A v = 1.08∙10-6 m ∙ rad.
As a result of symmetry of the structure and the force, the whole model of the side frame of truck and the loading model are shown in Fig. 2a and b, respectively.
Here P is the vibration force that come from the air rings located between the center of side frame and car body, F is the vibration force that come from spring and damper of axle box, and f 1 and f 2 represent the distribution loads of the inertial force and inertial moments caused by vibration acceleration. In order to know the position of weak link of the frame, a stress chart (Fig. 3) is derived by locating the unit load (1 kN) in the center of side frame. From the chart, we find the weak link of the side frame, as shown in Fig. 2.
According to Eqs. (6), (7) and Fig. 2b, the stress function of the weak link is obtained as
and
where
and W z0 is called the section modulus of the weak link,
where m b is the mass of the truck, J b is the moment of inertia of the truck, C 1 and K 1 are damping and stiffness located on the axle box, respectively. According to Eq. (11), the response spectra of the truck may be written as
substituting Eqs. (16), (18), and (19) into Eq. (9) and substitution of the parameters of the truck then numbering computation, the SPSD Gs(ω) of the weak link can be obtained. As an example of stress power spectral density, exhibited by the train at speed of 180 km per hour is given in Fig. 4.
where
S is random stress when the average value is zero. Generally, the fatigue curve can be described as follows:
where S is reversed stress amplitude, N is number of cycles to failure, and m and C are material constants of the structure.
According to the Miner cumulative damage law [7, 8], the fatigue life computational equation can be obtained as follows:
From statistics, the fatigue life of structure accords with log normal distribution. In the light of this, the fatigue life equation for different reliabilities can be deduced as
where
η(N) = σ N /μ N is called change coefficient, μ N and σ N are average value and standard deviation, and \( \overline{N} \) is the life when the reliability is 50%. Its value is equal to T f .
In this paper, we computed the fatigue life of a side frame for four reliabilities, when the train runs at 60 to 200 km/h, as shown in Fig. 5.
Conclusions. A method for calculating the stress power spectral density of a general linear dynamic system on the basis of the unit load stress matrix is put forward. The relationship between the stress power spectral density of dynamic components and the response spectrum of dynamic system is established, and the corresponding formulas are derived. This is very important for the numerical emulation in dynamic fatigue design and reliability fatigue life prediction by computer. The dynamic response computation and fatigue life prediction of the CW-200k type vehicle truck are performed using the method and the high level ORE track spectrum.
The proposed method is suitable not only for the running dynamic system but also for new design dynamic systems.
References
Vijay K. Garg and Rao V. Dukkipati, Dynamics of Railway Vehicle Systems, Academic Press, New York (1984), pp. 1–102.
Hu JinYa and Zeng SanYuan, Modern Random Vibration [in Chinese], Railway Book Company of China, Beijing (1989), pp. 38–114.
Zhu Weiqiu, Random Vibration [in Chinese], Science Press, Beijing (1998), pp. 21–69.
Running Analyses in ADAMS/Rail (2002), pp. 38–39.
S. H. Crandall and W. D. Mark, Random Vibration in Mechanical Systems, Academic Press, New York (1963).
N. Willems, J. T. Easley, and S. T. Rolfe, Strength of Materials, McGraw-Hill Book Company, New York (1981), pp. 381–422.
V. A. Avakov and R. G. Shomperlen, “Fatigue reliability functions,” J. Vibr. Acoust. Stress Reliab. Des., 111, No. 4, 443–455 (1989).
Lu Pengmin, “A probabilistic model of the fatigue accumulation damage for the welded structure in the long life fatigue,” Chinese J. Appl. Mech., 16, No. 1, 100–103 (1999).
A. P. Bovsunovskii and V. V. Matveev, “Vibration characteristics of fatigue damage of beam-type structural components,” Strength Mater., 34, No. 1, 35–48 (2002).
A. D. Pogrebnyak, M. N. Regul’skii, and A. V. Zheldubovskii, “Assessment of the effect of stress concentration on the fatigue resistance of structural materials under asymmetrical loading,” Strength Mater., 45, No. 1, 82–92 (2013).
V. A. Kruts, A. P. Zinkovskii, and E. A. Sinenko, “Influence of a fatigue crack on the vibrations of the simplest regular elastic system,” Strength Mater., 45, No. 3, 308–315 (2013).
V. G. Piskunov and R. V. Grynevyts’kyi, “Solution of the problem on the vibrations of beams with a variable cross section using the finite-difference method,” Strength Mater., 44, No. 1, 53–58 (2012).
Acknowledgments
The work is supported by National Natural Science foundation of China (No. 50875070).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Problemy Prochnosti, No. 3, pp. 162 – 169, May – June, 2015.
Rights and permissions
About this article
Cite this article
Zhao, W., Zhou, X. & Shen, M. A Method of Virtual Design of the Fatigue Life of a Dynamic Structure. Strength Mater 47, 507–513 (2015). https://doi.org/10.1007/s11223-015-9683-6
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11223-015-9683-6