Abstract
To investigate wear characteristics of tunnel boring machine (TBM) disc cutter rings interacting with types of rock, a range of wear tests were performed on a TBM cutter test rig, and laboratory-scale disc cutters were used in the experiments. The mass loss, vertical load, temperature field, wear mechanism and change rule of cutter tip for the disc cutter rings were obtained during the tests. The results indicate that the rock types and properties of rock exhibit great influences on the cutter wear. The variation of the weight loss testing with different types of rock is partially explained by the discrepancies of vertical load, cutting temperature, and the transition of wear mechanisms. In addition, the test results show that the wear characteristics of cutter rings are mainly affected by uniaxial compressive strength (UCS) rather than equivalent quartz content (EQC) for types of rock. This study will benefit the design of cutter rings with enhanced wear resistance.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Abu Bakar MZ, Majeed Y, Rostami J (2016) Effects of rock water content on CERCHAR Abrasivity Index. Wear 368:132–145, DOI: https://doi.org/10.1016/j.wear.2016.09.007
Alber M (2008) Stress dependency of the cerchar abrasivity index (CAI) and its effects on wear of selected rock cutting tools. Tunnelling and Underground Space Technology 23(4):351–359, DOI: https://doi.org/10.1016/j.tust.2007.05.008
Archard JF, Hirst W (1956) The wear of metals under unlubricated conditions. Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences 236(1206):397–410, DOI: https://doi.org/10.1098/rspa.1956.0144
Balci C, Tumac D (2012) Investigation into the effects of different rocks on rock cuttability by a V-type disc cutter. Tunnelling and Underground Space Technology 30:183–193, DOI: https://doi.org/10.1016/j.tust.2012.02.018
Barzegari G, Uromeihy A, Zhao J (2015) Parametric study of soil abrasivity for predicting wear issue in TBM tunneling projects. Tunnelling and Underground Space Technology 48:43–57, DOI: https://doi.org/10.1016/j.tust.2014.10.010
Capik M, Yilmaz AO (2017) Correlation between Cerchar abrasivity index, rock properties, and drill bit lifetime. Arabian Journal of Geosciences 10:15, DOI: https://doi.org/10.1007/s12517-016-2798-7
Choi SO, Lee SJ (2016) Numerical study to estimate the cutting power on a disc cutter in jointed rock mass. KSCE Journal of Civil Engineering 20(1):440–451, DOI: https://doi.org/10.1007/s12205-015-2265-0
Er S, Tuğrul A (2016) Estimation of Cerchar abrasivity index of granitic rocks in Turkey by geological properties using regression analysis. Bulletin of Engineering Geology and the Environment 75(3):1325–1339, DOI: https://doi.org/10.1007/s10064-016-0853-y
Geng Q, Wei Z, Meng H, Macias FJ, Bruland A (2016) Free-face-assisted rock breaking method based on the multi-stage tunnel boring machine (TBM) cutterhead. Rock Mechanics and Rock Engineering 49(11):4459–4472, DOI: https://doi.org/10.1007/s00603-016-1053-6
Gu DD, Jue JB, Dai DH, Lin KJ, Chen WH (2017) Effects of dry sliding conditions on wear properties of al-matrix composites produced by selective laser melting additive manufacturing. ASME Journal of Tribology 140(2):021605, DOI: https://doi.org/10.1115/1.4037729
Jiang Q, Su G, Feng XT, Chen G, Zhang MZ, Liu C (2019) Excavation optimization and stability analysis for large underground caverns under high geostress: A case study of the Chinese Laxiwa project. Rock Mechanics and Rock Engineering 52(3):895–915, DOI: https://doi.org/10.1007/s00603-018-1605-z
Jiang Q, Yang B, Yan F, Liu C, Shi Y, Li L (2020) New method for characterizing the shear damage of natural rock joint based on 3D engraving and 3D scanning. International Journal of Geomechanics 20(2), DOI: https://doi.org/10.1061/(ASCE)GM.1943-5622.0001575
Ko TY, Kim TK, Son Y, Jeon S (2016) Effect of geomechanical properties on Cerchar Abrasivity Index (CAI) and its application to TBM tunneling. Tunnelling and Underground Space Technology 57:99–111, DOI: https://doi.org/10.1016/j.tust.2016.02.006
Li Y, Di H, Yao Q, Fu L, Zhou S (2020) Prediction model for disc cutter wear of tunnel boring machines in sandy cobble strata. KSCE Journal of Civil Engineering 24(3):1010–1019, DOI: https://doi.org/10.1007/s12205-020-1631-8
Lin LK, Mao QS, Xia YM, Zhu ZM, Yang D, Guo B, Lan H (2017) Experimental study of specific matching characteristics of tunnel boring machine cutter ring properties and rock. Wear 378–379:1–10, DOI: https://doi.org/10.1016/j.wear.2017.01.072
Lislerud A (1997) Principles of mechanical excavation. Possiva report, No. 97-12, Posiva Oy, Helsinki, Finland
Macias FJ, Dahl F, Bruland A (2016) New rock abrasivity test method for tool life assessments on hard rock tunnel boring: The rolling indentation abrasion test (RIAT). Rock Mechanics and Rock Engineering 49(5):1679–1693, DOI: https://doi.org/10.1007/s00603-015-0854-3
Moradizadeh M, Cheshomi A, Ghafoori M, TrighAzali S (2016) Correlation of equivalent quartz content, slake durability index and Is50 with Cerchar abrasiveness index for different types of rock. International Journal of Rock Mechanics and Mining Sciences 86:42–47, DOI: https://doi.org/10.1016/j.ijrmms.2016.04.003
Petrica M, Badisch E, Peinsitt T (2013) Abrasive wear mechanisms and their relation to rock properties. Wear 308:86–94, DOI: https://doi.org/10.1016/j.wear.2013.10.005
Petrica M, Painsi M, Badisch E, Peinsitt T (2014) Wear mechanisms on martensitic steels generated by different rock types in two-body conditions. Tribology Letters 53(3):607–616, DOI: https://doi.org/10.1007/s11249-014-0298-z
Plinninger R, Käsling H, Thuro K, Spaun G (2003) Testing conditions and geomechanical properties influencing the CERCHAR abrasiveness index (CAI) value. International Journal of Rock Mechanics and Mining Sciences 40(2):259–263, DOI: https://doi.org/10.1016/S1365-1609(02)00140-5
Ribacchi R, Fazio AL (2005) Influence of rock mass parameters on the performance of a TBM in a gneissic formation (Varzo Tunnel). Rock Mechanics and Rock Engineering 38(2):105–127, DOI: https://doi.org/10.1007/s00603-004-0032-5
Rostami J (1993) Development of a force estimation model for rock fragmentation with disc cutters through the theoretical modeling and physical measurement of crushed zone pressure. PhD Thesis, Colorado School of Mines, Golden, CO, USA
Rostami J (2013) Study of pressure distribution within the crushed zone in the contact area between rock and disc cutters. International Journal of Rock Mechanics and Mining Sciences 57:172–186, DOI: https://doi.org/10.1016/j.ijrmms.2012.07.031
Rostami J, Ghasemi A, Alavi Gharahbagh E, Dogruoz C, Dahl F (2014) Study of dominant factors affecting cerchar abrasivity index. Rock Mechanics and Rock Engineering 47(5):1905–1919, DOI: https://doi.org/10.1007/s00603-013-0487-3
Thuro K (1997) Drillability prediction-geological influences in hard rock drill and blast tunneling. Geologische Rundschau 86(2):426–437, DOI: https://doi.org/10.1007/s005310050151
Tumac D, Balci C (2015) Investigations into the cutting characteristics of CCS type disc cutters and the comparison between experimental, theoretical and empirical force estimations. Tunnelling and Underground Space Technology 45:84–98, DOI: https://doi.org/10.1016/j.tust.2014.09.009
Wang L, Kang Y, Cai Z, Zhang Q, Zhao Y, Zhao H, Su P (2012) The energy method to predict disc cutter wear extent for hard rock TBMs. Tunnelling and Underground Space Technology 28:183–191, DOI: https://doi.org/10.1016/j.tust.2011.11.001
Wang L, Kang Y, Zhao X, Zhang Q (2015) Disc cutter wear prediction for a hard rock TBM cutterhead based on energy analysis. Tunnelling and Underground Space Technology 50:324–333, DOI: https://doi.org/10.1016/j.tust.2015.08.003
Wang WJ, Liu TF, Wang HY, Liu QY, Zhu MH, Jin XS (2014) Influence of friction modifiers on improving adhesion and surface damage of wheel/rail under low adhesion conditions. Tribology International 75:16–23, DOI: https://doi.org/10.1016/j.triboint.2014.03.008
Wang WJ, Wang H, Wang HY, Guo J, Liu QY, Zhu MH, Jin XS (2013) Sub-scale simulation and measurement of railroad wheel/rail adhesion under dry and wet conditions. Wear 302(1–2):1461–1467, DOI: https://doi.org/10.1016/j.wear.2012.12.014
Wei MX, Chen KM, Wang SQ, Cui XH (2011) Analysis for wear behaviors of oxidative wear. Tribology Letters 42(1):1–7, DOI: https://doi.org/10.1007/s11249-010-9741-y
West G (1989) Rock abrasiveness testing for tunnelling. International Journal of Rock Mechanics and Mining Sciences 26(2):151–160, DOI: https://doi.org/10.1016/0148-9062(89)90003-x
Yang HQ, Li Z, Jie TQ, Zhang ZQ (2018) Effects of joints on the cutting behavior of disc cutter running on the jointed rock mass. Tunnelling and Underground Space Technology 81:112–120, DOI: https://doi.org/10.1016/j.tust.2018.07.023
Yaralı O, Duru H (2016) Investigation into effect of scratch length and surface condition on Cerchar abrasivity index. Tunnelling and Underground Space Technology 60:111–120, DOI: https://doi.org/10.1016/j.tust.2016.08.005
Yaralı O, Yaşar E, Bacak G, Ranjith PG (2008) A study of rock abrasivity and tool wear in coal measures rocks. International Journal of Coal Geology 74(1):53–66, DOI: https://doi.org/10.1016/j.coal.2007.09.007
Zhang HM (2010) Analysis of damages of TBM disc cutters and countermeasures. Modern Tunnelling Technology 47(6):40–45 (in Chinese)
Zhang X, Xia Y, Tan Q, Wu D (2018) Comparison study on the rock cutting characteristics of disc cutter under free-face-assisted and conventional cutting methods. KSCE Journal of Civil Engineering 22(10):4155–4162, DOI: https://doi.org/10.1007/s12205-018-0577-6
Zhang Z, Meng L, Sun F (2014) Wear analysis of disc cutters of full face rock tunnel boring machine. Chinese Journal of Mechanical Engineering 27(6):1294–1300, DOI: https://doi.org/10.3901/CJME.2014.0905.145
Zhou P, Guo J, Sun J, Zou D (2019) Theoretical research and simulation analysis on the cutter spacing of double disc cutters breaking rock. KSCE Journal of Civil Engineering 23(7):3218–3227, DOI: https://doi.org/10.1007/s12205-019-1777-4
Acknowledgements
This research is supported by the National Key R&D Program of China (No. 2018YFB1306700), the National Natural Science Foundation of China (No. 51905550), the China Postdoctoral Science Foundation (No. 2019M652795), and the Major Science and Technology Projects of Hunan Province (No. 2019GK1010).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Lin, L., Xia, Y. & Zhang, X. Wear Characteristics of TBM Disc Cutter Ring Sliding against Different Types of Rock. KSCE J Civ Eng 24, 3145–3155 (2020). https://doi.org/10.1007/s12205-020-2208-2
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12205-020-2208-2