Abstract
To improve the excavation efficiency of Tunnel Boring Machines (TBMs), the free-face-assisted rock cutting method induced by TBM disc cutter (FM) was explored and the differences between the FM and the conventional Cutting Method (CM) were also compared based on a series of rock cutting tests. The results show that when the free face distance is less than a critical value, the FM can promote the tensile failure of the rock and the formation of big rock debris effectively. Moreover, the cutting efficiency and the cutting forces including normal force, rolling force and side force of the disc cutter under the FM are also significantly reduced and improved, respectively, compared to that under the CM. The FM can be applied in multi-stage cutterhead TBMs to improve the cutting efficiency and reduce the failure of the disc cutter, the research results indicate that the free face distance should be controlled within 80 mm to use the free face effectively.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Balci, C. and Tumac, D. (2012). “Investigation into the effects of different rocks on rock cuttability by a V-type disc cutter.” Tunnelling and Underground Space Technology, Vol. 30, No. 4, pp. 183–193, DOI: 10.1016/j.tust.2012.02.018.
Bejari, H. and Khademi Hamidi, J. (2013). “Simultaneous effects of joint spacing and orientation on TBM cutting efficiency in jointed rock masses.” Rock Mechanics and Rock Engineering, Vol. 46, No. 4, pp. 897–907, DOI: 10.1007/s00603-012-0314-2.
Bilgin, N., Copur, H., and Balci, C. (2012). “Effect of replacing disc cutters with chisel tools on performance of a TBM in difficult ground conditions.” Tunnelling and Underground Space Technology, Vol. 27, No. 1, pp. 41–51, DOI: 10.1016/j.tust.2011.06.006.
Cho, J. W., Jeon, S., Jeong, H. Y., and Chang, S. H. (2013). “Evaluation of cutting efficiency during TBM disc cutter excavation within a Korean granitic rock using linear-cutting-machine testing and photogrammetric measurement.” Tunnelling and Underground Space Technology, Vol. 35, No. 4, pp. 37–54, DOI: 10.1016/j.tust.2012.08.006.
Cho, J., Jeon, S., Yu, S., and Chang, S. (2010). “Optimum spacing of TBM disc cutters: A numerical simulation using the three-dimensional dynamic fracturing method.” Tunnelling and Underground Space Technology, Vol. 25, No. 3, pp. 230–244, DOI: 10.1016/j.tust.2009.11.007.
Choi, S. and Lee, S. (2015). “Three-dimensional numerical analysis of the rock-cutting behavior of a disc cutter using particle flow code.” KSCE Journal of Civil Engineering, Vol. 19, No. 4, pp. 1129–1138, DOI: 10.1007/s12205-013-0622-4.
Choi, S. and Lee, S. (2016). “Numerical study to estimate the cutting power on a disc cutter in jointed rock mass.” KSCE Journal of Civil Engineering, Vol. 20, No. 1, pp. 440–451, DOI: 10.1007/s12205-015-2265-0.
Ciccu, R. and Grosso, B. (2014). “Improvement of disc cutter performance by water jet assistance.” Rock Mechanics and Rock Engineering, Vol. 47, No. 2, pp. 733–744, DOI: 10.1007/s00603-013-0433-4.
Geng, Q., Wei, Z., and Meng, H. (2014). “Numerical and experimental method to determine the boring diameters of a two-stage TBM cutterhead to prevent rock burst.” Journal of Mechanical Science and Technology, Vol. 28, No. 11, pp. 4613–4620, DOI: 10.1007/s12206-014-1029-y.
Geng, Q., Wei, Z., and Meng, H. (2016b). “An experimental research on the rock cutting process of the gage cutters for rock Tunnel Boring Machine (TBM).” Tunnelling and Underground Space Technology, Vol. 52, No. 2016, pp. 182–191, DOI: 10.1016/j.tust.2015.12.008.
Geng, Q., Wei, Z., He, F., and Meng, H. (2015). “Comparison of the mechanical performance between two-stage and flat-face cutter head for the rock Tunnel Boring Machine (TBM).” Journal of Mechanical Science and Technology, Vol. 29, No. 5, pp. 2047–2058, DOI: 10.1007/s12206-015-0425-2.
Geng, Q., Wei, Z., Meng, H., and Chen, Q. (2016a). “Numerical and experimental research on the rock-breaking process of tunnel boring machine normal disc cutters.” Journal of Mechanical Science and Technology, Vol. 30, No. 4, pp. 1733–1745, DOI: 10.1007/s12206-016-0329-9.
Gertsch, R., Gertsch, L., and Rostami, J. (2007). “Disc cutting tests in Colorado Red Granite: Implications for TBM performance prediction.” Int. J. Rock Mech. Min. Sci., Vol. 44, No. 2, pp. 238–246, DOI: 10.1016/j.ijrmms.2006.07.007.
Gong, Q. M., Jiao, Y. Y., and Zhao, J. (2006). “Numerical modeling of the effects of joint spacing on rock fragmentation by TBM cutters.” Tunnelling and Underground Space Technology, Vol. 21, No. 1, pp. 46–55, DOI: 10.1016/j.tust.2005.06.004.
Hassani, F., Nekoovaght, P. M., and Gharib, N. (2016). “The influence of microwave irradiation on rocks for microwave-assisted underground excavation.” Journal of Rock Mechanics and Geotechnical Engineering, Vol. 8, No. 1, pp. 1–15, DOI: 10.1016/j.jrmge.2015.10.004.
Hood, M. and Alehossein, H. (2000). “A development in rock cutting technology.” International Journal of Rock Mechanics and Mining Sciences, Vol. 37, Nos. 1–2, pp. 297–305, DOI: 10.1016/S1365-1609(99)00107-0.
Liu, J., Cao, P., and Han, D. (2016). “Sequential indentation tests to investigate the influence of confining stress on rock breakage by tunnel boring machine cutter in a biaxial state.” Rock Mechanics and Rock Engineering, Vol. 49, No. 4, pp. 1–17, DOI: 10.1007/s00603-015-0843-6.
Liu, J., Cao, P., Du, C., Jiang, Z., and Liu, J. (2015a). “Effects of discontinuities on penetration of TBM cutters.” Journal of Central South University, Vol. 22, No. 9, pp. 3624–3632,DOI: 10.1007/s11771-015-2903-1.
Liu, J., Cao, P., Liu, J., and Jiang, Z. (2015b). “Influence of confining stress on fracture characteristics and cutting efficiency of TBM cutters conducted on soft and hard rock.” Journal of Central South University, Vol. 22, No. 5, pp. 1947–1955, DOI: 10.1007/s11771-015-2714-4.
Ma, H., Gong, Q., Wang, J., Yin, L., and Zhao, X. (2016). “Study on the influence of confining stress on TBM performance in granite rock by linear cutting test.” Tunnelling and Underground Space Technology, Vol. 57, pp. 145–150, DOI: 10.1016/j.tust.2016.02.020.
Ramezanzadeh, A. and Hood, M. (2010). “A state-of-the-art review of mechanical rock excavation technologies.” Journal of Mining and Environment, Vol. 1, No. 1, pp. 29–39.
Rostami, J. (1997). Development of a force estimation model for rock fragmentation with disc cutters through theoretical modeling and physical measurement of crushed zone pressure, Ph.D. Thesis, Colorado School of Mines, Golden, Colorado, USA.
Rostami, J. (2013). “Study of pressure distribution within the crushed zone in the contact area between rock and disc cutters.” International Journal of Rock Mechanics and Mining Sciences, Vol. 57, No. 1, pp. 172–186, DOI: 10.1016/j.ijrmms.2012.07.031.
Tiryaki, B. and Dikmen, A. C. (2006). “Effects of rock properties on specific cutting energy in linear cutting of sandstones by picks.” Rock Mechanics and Rock Engineering, Vol. 39, No. 2, pp. 89–120, DOI: 10.1007/s00603-005-0062-7.
Tumac, D. and Balci, C. (2015). “Investigations into the cutting characteristics of CCS type disc cutters and the comparison between experimental, theoretical and empirical force estimations.” Tunnelling and Underground Space Technology, Vol. 45, No. 45, pp. 84–98, DOI: 10.1016/j.tust.2014.09.009.
Yin, L. J., Gong, Q. M., and Zhao, J. (2014a). “Study on rock mass boreability by TBM penetration test under different in situ stress conditions.” Tunnelling and Underground Space Technology, Vol. 43, No. 45, pp. 413–425, DOI: 10.1016/j.tust.2014.06.002.
Yin, L. J., Gong, Q. M., Ma, H. S., Zhao, J., and Zhao, X. B. (2014b). “Use of indentation tests to study the influence of confining stress on rock fragmentation by a TBM cutter.” International Journal of Rock Mechanics and Mining Sciences, Vol. 72, No. 72, pp. 261–276, DOI: 10.1016/j.ijrmms.2014.07.022.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zhang, X., Xia, Y., Tan, Q. et al. Comparison Study on the Rock Cutting Characteristics of Disc Cutter under Free-face-assisted and Conventional Cutting Methods. KSCE J Civ Eng 22, 4155–4162 (2018). https://doi.org/10.1007/s12205-018-0577-6
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12205-018-0577-6