Abstract
One of the key components of a microsensor is the Micro electromechanical system (MEMS) microheater. It has a wide range of applications such as gas sensors, pressure sensors, and so on. In this study, a platinum microhotplate based on suspended membrane structure is introduced. A simple microfabrication process is adopted to form the micromachined suspended microheater. Some integrated circuit processes such as E-beam evaporation of Pt and Au, oxidation, wet etching process, and photolithography process are used to fabricate the device. As the usage of deep-reactive ion etching and low-pressure chemical vapor deposition systems are avoided, the microfabrication process of the hotplate is accessible even in laboratories with limited equipment. In order to achieve uniform temperature distribution over the active heater area and to increase the robustness of the membrane, a thin silicon island was placed underneath the dielectric membrane. Thermal and thermomechanical behaviors of this structure obtained by finite element analysis show that the designed microhotplate is relatively strong. Experimental results show that power consumption and time constant are 50mW and 4.23ms, respectively, for the temperature variation from 30°C to 500°C in the fabricated microhotplates.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Reference
Courbat, J., Canonica, M., Teyssieux, D., Briand, D., and De Rooij, N., “Design and Fabrication of Micro-hotplates Made on a Polyimide Foil: Electrothermal Simulation and Characterization to Achieve Power Consumption in the Low mW Range,” Journal of Micromechanics and Microengineering 21: 015014 (2010).
Dai, C.-L., “A Capacitive Humidity Sensor Integrated with Micro Heater and Ring Oscillator Circuit Fabricated by CMOS–MEMS Technique,” Sensors and Actuators B: Chemical 122: 375–380 (2007).
Elmi, I., Zampolli, S., Cozzani, E., Mancarella, F., and Cardinali, G., “Development of ultra-low-power consumption MOX sensors with ppb-level VOC detection capabilities for emerging applications,” Sensors and Actuators B: Chemical 135: 342–351 (2008).
Hwang, W.-J., Shin, K.-S., Roh, J.-H., Lee, D.-S., and Choa, S.-H., “Development of micro-heaters with optimized temperature compensation design for gas sensors,” Sensors 11: 2580–2591 (2011).
Konz, W., Hildenbrand, J., Bauersfeld, M., et al., “Micromachined IR-source with Excellent Blackbody Like Behaviour,” Proceedings of SPIE 5836: 540–548 (2005).
Tao, C., Yin, C., He, M., and Tu, S., “Thermal Analysis and Design of a Micro-hotplate for Si-substrated Micro-structural Gas Sensor,” 3rd IEEE International Conference on Nano/Micro Engineered and Molecular Systems (NEMS 2008), Sanya, Hainan Island, China, pp. 284–287 (2008).
Courbat, J., Briand, D., and De Rooij, N.F., “Reliability Improvement of Suspended Platinum-based Micro-heating Elements,” Sensors and Actuators A: Physical 142: 284–291 (2008).
Chung, G.-S., and Jeong, J.-M., “Fabrication of Micro Heaters on Polycrystalline 3C-SiC Suspended Membranes for Gas Sensors and their Characteristics,” Microelectronic Engineering 87: 2348–2352 (2010).
Laconte, J., Flandre, D., and Raskin, J.-P., Micromachined Thin-film Sensors for SOI-CMOS Co-integration, Volume XIII, Springer, Berlin, Germany, p. 292 (2006ISBN: 0-387-28842-2).
Belmonte, J.C., Puigcorbe, J., Arbiol, J., et al., “High-Temperature Low-power Performing Micromachined Suspended Micro-hotplate for Gas Sensing Applications,” Sensors and Actuators B: Chemical 114: 826–835 (2006).
Guo, B., Bermak, A., Chan, P.C., and Yan, G.-Z., “A Monolithic Integrated 4× 4 Tin Oxide Gas Sensor Array with On-Chip Multiplexing and Differential Readout Circuits,” Solid-State Electronics 51: 69–76 (2007).
Hotovy, I., Rehacek, V., Mika, F., et al., “Gallium Arsenide Suspended Microheater for MEMS Sensor Arrays,” Microsystem Technologies 14: 629–635 (2008).
Lee, D.-S., Shim, C.-H., Lim, J.-W., Huh, J.-S., Lee, D.-D., and Kim, Y.-T., “A Microsensor Array with Porous Tin Oxide Thin Films and Microhotplate Dangled by Wires in Air,” Sensors and Actuators B: Chemical 83: 250–255 (2002).
Lee, K.-N., Lee, D.-S., Jung, S.-W., Jang, Y.-H., Kim, Y.-K., and Seong, W.-K., “A High-temperature MEMS Heater Using Suspended Silicon Structures,” Journal of Micromechanics and Microengineering 19: 115011 (2009).
Ehmann, M., Ruther, P., von Arx, M., and Paul, O., “Operation and Short-term Drift of Polysilicon-heated CMOS Microstructures at Temperatures up to 1200 K,” Journal of Micromechanics and Microengineering 11: 397 (2001).
Aslam, M., Gregory, C., and Hatfield, J., “Polyimide Membrane for Micro-heated Gas Sensor Array,” Sensors and Actuators B: Chemical 103: 153–157 (2004).
Yi, X., Lai, J., Liang, H., and Zhai, X., “Fabrication of a MEMS Micro-hotplate,” Journal of Physics: Conference Series 276: 012098 (2011).
Bauer, D., Heeger, M., Gebhard, M., and Benecke, W., “Design and Fabrication of a Thermal Infrared Emitter,” Sensors and Actuators A: Physical 55: 57–63 (1996).
Kishi, N., and Hara, H., “Lifetime Evaluation of Self-modulated MEMS Infrared Light Source Made of Single Crystalline Silicon,” SICE, 2007 Annual Conference, Kagawa University, Takamatsu City, Kagawa, Japan, pp. 2451–2454 (2007).
Astié, S., Gue, A., Scheid, E., and Guillemet, J., “Design of a Low Power SnO2 Gas Sensor Integrated on Silicon Oxynitride Membrane,” Sensors and Actuators B: Chemical 67: 84–88 (2000).
Briand, D., Gretillat, M., and van der Schoot, B., and De Rooij, N., “Thermal Management of Micro-hotplates Using MEMCAD as Simulation Tool,” Proceedings of the MSM 2000 International Conference On Modeling and Simulation of Microsystems, U.S. Grant hotel, San Diego, March 27–29 (2000).
Ruther, P., Ehmann, M., Lindemann, T., and Paul, O., “Dependence of the Temperature Distribution in Micro Hotplates on Heater Geometry and Heating Mode,” 12th International Conference on Transducers, Solid-State Sensors, Actuators and Microsystems, Boston, MA, pp. 73–76 (2003).
Dennis, J.O., Ahmed, A.Y., and Mohamad, N.M., “Design, Simulation and Modeling of a Micromachined High Temperature Microhotplate for Application in Trace Gas Detection,” International Journal of Engineering and Technology 10: 89–96 (2010).
Sidek, O., Ishak, M., Khalid, M., Abu Bakar, M., and Miskam, M., “Effect of Heater Geometry on the High Temperature Distribution on a MEMS micro-hotplate,” 2011 3rd Asia Symposium on Quality Electronic Design (ASQED), Kuala Lumpur, Malaysia, pp. 100–104 (2011).
Lee, J., Spadaccini, C.M., Mukerjee, E.V., and King, W.P., “Differential Scanning Calorimeter Based on Suspended Membrane Single Crystal Silicon Microhotplate,” Journal of Microelectromechanical Systems 17: 1513–1525 (2008).
Abdollahi H, Hajghassem H, Mohajerzadeh S. Simple Fabrication of an Uncooled Al/SiO2 Microcantilever IR Detector Based on Bulk Micromachining. Microsystem Technologies 20: 387–396 (2014).
Mayadas, A., and Shatzkes, M., “Electrical-resistivity Model for Polycrystalline Films: The Case of Arbitrary Reflection at External Surfaces,” Physical Review B 1: 1382 (1970).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Samaeifar, F., Afifi, A. & Abdollahi, H. Simple Fabrication and Characterization of a Platinum Microhotplate Based on Suspended Membrane Structure. Exp Tech 40, 755–763 (2016). https://doi.org/10.1007/s40799-016-0076-y
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40799-016-0076-y