Abstract
The inactivation of bioactive ingredients during spray drying is often matrix specific. Therefore, the design of new processes or the optimisation of existing spray drying processes is usually highly product specific and requires numerous experiments. Rapid experimentation methods that facilitate fast data generation are therefore desired. A novel method for drying single droplets to mimic spray drying is proposed. The approach involves droplet deposition on a hydrophobic flat surface followed by controlled drying. A heat and mass transfer model is applied to predict the drying history of the single droplets. The approach is successfully evaluated through studying the inactivation of β-galactosidase during drying. The heat and mass transfer model supplemented with inactivation kinetics provided reasonable prediction of the residual enzyme activity after drying. In addition, the inactivation kinetics could be directly extracted from single droplet experiments rather than using the kinetics from separate heating experiments. Finally, it was demonstrated that the inactivation kinetics found with the single-drop experiments could satisfactorily predict the residual activity of β-galactosidase dried with a laboratory-scale spray dryer.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
Spray drying belongs to the most common drying techniques for liquid food products. The fine atomisation of the product and the subsequent fast evaporation of water make it especially suitable to formulate heat-sensitive products (Xin Huang et al. 2006; Fang and Bhandari 2010). Despite the relative mild conditions during drying, (partial) inactivation of bioactive compounds such as enzymes, antioxidants and vitamins cannot be avoided. Optimisation of the spray drying conditions and addition of stabilizers is often required to retain maximum activity (Ré 1998; Peighambardoust et al. 2011; Sansone et al. 2011). In practice, numerous expensive pilot-scale trials are executed to explore different product formulations and to find optimum drying conditions.
Modelling tools are frequently used to accelerate process development and optimisation in spray drying. The availability of reliable inactivation kinetics—usually highly product specific—is a prerequisite for this. Kinetic models require experimental data from drying experiments for parameter calibration. Pilot-scale experiments are not ideal for this as they are expensive, time-consuming, and involve the evaluation of complex process conditions. A more efficient alternative is the application of small-scale representative drying experiments.
Once reliable inactivation kinetics are obtained, a process model of the dryer can be used to predict the impact of the drying on the remaining ingredient activity. Subsequently, the model can be used to approximate optimal drying conditions and product formulations in a more systematic way (Wijlhuizen et al. 1979; Luyben et al. 1982; Meerdink and van't Riet 1991; Millqvist-Fureby et al. 1999; Coumans 2000).
Small-scale spray drying has been carried out in laboratory-scale spray dryers (Gianfrancesco et al. 2010; Li et al. 2010; Wu et al. 2011). However, major differences between laboratory and industrial spray dryers are the smaller droplet size, caused by the different method of atomisation, and the shorter residence time in the laboratory spray dryer (Goula and Adamopoulos 2004; Filková et al. 2006). Since the laboratory spray dryer can (due to its design and dimensions) only cover a limited range of droplet sizes and drying times and it produces droplets with a size distribution (not monodisperse), it is virtually impossible to extract sufficient representative experimental data to calibrate a kinetic model.
Another approach is the drying of single droplets under well-controlled conditions. In this approach a small droplet is generated, immobilised, and subsequently dried by contacting it with well-defined drying air. Examples are drying of a droplet that is non-intrusively levitated using for example acoustic, aerodynamic or electromagnetic levitation (Adhikari et al. 2000; Sloth et al. 2006; Schiffter and Lee 2007), intrusively levitated that is in pendant or filament (Chuchottaworn et al. 1984; Ali Al Zaitone and Tropea 2011), or that is deposited on a flat surface (Perdana et al. 2011a).
In this study, the latter method is followed (Perdana et al. 2011a). The major advantages of this method are the possibility to vary droplet size and residence time, and to dry multiple droplets at once to obtain higher volume of sample. The minimum droplet diameter can be adjusted to 150 μm which is only slightly bigger than the typical droplet size in industrial spray dryers; a comparable droplet size is critical to accurately mimic the kinetics in spray drying (Adhikari et al. 2000; Vehring et al. 2007). The challenge in using this approach is the presence of the flat surface. This surface for example affects the spherical shape of the droplet. Therefore, a hydrophobic surface is used to minimize the contact between the droplet and the surface and to retain the spherical shape. Other differences introduced by the presence of the surface are the air flow velocity and the air temperature near the droplet, which deviate from the bulk conditions (Schlichting and Gersten 2000). By monitoring the air temperature near the droplet and by modelling the air flow and heat transfer across the drying surface, the influence of the surface on the drying conditions can be quantified.
This study focuses on the drying of the enzyme β-galactosidase suspended in a maltodextrin matrix. The enzyme β-galactosidase is selected as the model enzyme in this study, because it is an industrial relevant enzyme applied for production of lactose-hydrolysed milk and whey. Additionally, its activity can be easily determined and its inactivation kinetics has been studied before, though under steady-state conditions, providing strong basis for this study (Yamamoto and Sano 1992; Yoshioka et al. 1994; Perdana et al. 2011b). The inactivation kinetics of β-galactosidase from the previous studies were combined with the heat and mass transfer model to predict the residual activity of β-galactosidase during the single droplet drying experiments. Finally, the predictive value of the model was also checked by drying of β-galactosidase in a laboratory spray dryer system.
Modelling and Statistical Evaluation
This section consists of four parts: (1) model description for a single droplet drying, (2) modelling temperature and air flow distribution across the flat plate, (3) inactivation kinetics of β-galactosidase, and (4) parameter optimisation and statistical evaluation.
Model Description for Single Droplet Drying
In analogy to several previous studies, a heat and mass transfer model is used to describe the drying of a sessile single droplet (Sloth et al. 2006; Straatsma et al. 2007; Mezhericher et al. 2008). The sessile droplet is approximated as a spherical droplet, and it is thus assumed that the diffusion occurs only in the radial direction. For the small droplet sizes considered, the temperature gradient inside the droplet could be neglected. This assumption is valid if the Biot number (Bi) <0.1. Bi is defined as the ratio of external heat transfer (between air and droplet) and the internal heat transfer (in the droplet, Incropera and De Witt 1985).
In this study, Bi is around 0.02.
The following differential equation is used to describe the droplet mass change in time
where m d is the mass of the droplet, t is the time, k c is the mass transfer coefficient, R d is the droplet radius, M w is the molecular weight of water, R is the ideal gas constant, a w is the water activity, P satw is the saturated vapour of water at T d, T d is the temperature of the droplet, P ∞ is the vapour partial pressure in the bulk air and T ∞ is the bulk air temperature.
The developing moisture gradient inside the droplet is described by Fickian diffusion
Where C w is the water concentration, D w,d is the effective diffusion coefficient of water in the droplet and r is the radial coordinate. The boundary conditions applied here are
The temperature change of the droplet is described by the following enthalpy balance:
where m s is the mass of the solute, c p,w and c p,s the heat capacity of the water and the solute respectively, h d the heat transfer coefficient to the droplet through convection and H lv is the evaporation enthalpy of water.
The coupled heat and mass transfer models were solved numerically using 100 radial layers in the droplet. In each layer the same solute mass (m s) was calculated according to
where C s,0 is the initial solute concentration and V d,0 is the initial volume of the droplet.
Since the initial solute concentration is assumed homogenous, the initial solute mass distribution is approximated with the initial volume distribution. The radial position of the i th layer from the centre of the droplet can be calculated as follows
where n is the total number of layers for numerical integration. The layer thickness Δr is
The volume of each layer V is then
where ρ w and ρ s are the densities of water and solute, respectively. The average water concentration is then defined as
Reorganizing Eq. 9. results in
The droplet shrinks upon drying due to the evaporation of water. This shrinkage influences the heat and mass transfer within the droplet. The model was therefore corrected to describe the decrease of layer thickness due to shrinkage (Farid 2003). This correction was based on the water concentration in every layer at t > 0 that is calculated from Eq. 3 (Crank 1990). From the water concentration, the new volume of the layer was recalculated as
The radial coordinate of every partition was corrected using this new volume. The radius of the ith partition is
The thickness of every partition could be recalculated using Eq. 7. To solve the model, several closure equations like heat and mass transfer coefficient, water activity, moisture diffusion coefficient, and vapour pressure are required, which are tabulated in Table 1.
Modelling Temperature and Air Flow Distribution Across the Flat Plate
In this study, the droplet was deposited on a flat plate. The drawback of this configuration is that in addition to heat transfer from the air to the droplet, also heat is transferred from the air to the flat plate through convection. This heat is further transferred from the plate to the droplet through conduction. It is of major importance to quantify the heat transfer between the flat plate and the droplet and compare this to the convective heat transfer via the drying air. The conductive heat transfer between the flat plate and the droplet is preferably as low as possible, when one wants to mimic the drying of a droplet suspended in air. By using a hydrophobic surface, the contact area for conductive heat transfer has already been reduced. Furthermore, the temperature in the air near the flat plate deviates from the bulk air temperature affecting the drying process. Therefore a model description of the temperature gradients within the plate and in the air near the plate was developed.
To minimize turbulence (eddy formation) near the edge of the depositing plate, a thin flat plate is used rather than a blunt-edged plate. However, the presence of the flat plate still influences the flow pattern of the drying air above the plate, i.e. near the droplet (Fig. 1). A boundary layer model according to Mosaad (1999) is used to describe the air flow and temperature distribution across the flat plate: a hydrodynamic boundary layer is defined for the air flow distribution and a thermal boundary layer for the temperature distribution
where z is the height coordinate from the surface of the flat plate, u is the air velocity at z, u ∞ is the bulk velocity of air, υ is the kinematics viscosity of air, T p,x is the temperature of the surface of the flat plate at distance x (at the front edge of the flat plate, x = 0), T ∞ is the bulk air temperature, δ is the hydrodynamic boundary layer at distance x and δ t is the thermal boundary layer. The hydrodynamic boundary layer for u = 0.99u ∞ is (Schlichting and Gersten 2000)
and δ t is thermal boundary layer at distance x
The heat transfer coefficient between the air and the flat plate h p is approximated by (Thirumaleshwar 2009)
where λ a is the thermal conductivity of air, Pr is the Prandtl number of air, c p,a is the heat capacity of air and μ a is the dynamic viscosity of air. The value of λ a, c p,a and μ a are temperature dependent; in Eq. 17, the value are evaluated at T = (T p + T ∞ )/2.
The heat transfer coefficient decreases as a function of the x coordinate (Eq. 17) and is calculated locally. It was estimated numerically; i.e. assuming a ∆x at distance L from the front side of the plate, the average heat transfer coefficient is obtained by integrating h p along ∆x
where h p,avg is the average local heat transfer coefficient.
The non-uniform heat transfer rate across the plate contributes to the development of a temperature gradient within the plate. The temperature distribution within the plate is described with a one-dimensional partial differential equation (Kakac and Yener 1993). It is assumed that no temperature gradient in the y direction (perpendicular to the air flow direction) and in the z direction (within the plate; because of the small thickness, i.e. 150 μm)
where ρ p is the density of the plate, Z is the thickness of the flat plate and λ p is the thermal conductivity of the flat plate. The boundary layer applied here are that near the droplet the flat plate temperature is equal to the droplet temperature and at the edge of the flat plate (far from the droplet) the temperature gradient of the flat plate is 0.
Equations 14 and 19 were solved numerically to estimate the temperature distribution history within and above the flat plate. The predictions were validated by simple temperature measurements at different heights above the plate.
To estimate the conductive heat transfer between the surface and the droplet and compare it to the convective heat transfer between the air and the droplet, the conductive heat flux Q through the contact surface of the droplet was estimated according to
where ΔT cond/Δx cond is the temperature gradient in the partition layer of the flat plate that is closest the droplet. It was found that the conductive heat flux was smaller than 5% of the total heat transferred to the droplet regardless of its position. Therefore, it can be safely assumed that most heat is transferred via convective heat transfer.
Inactivation Kinetics of β-galactosidase
The inactivation rate of the β-galactosidase is affected by the temperature and moisture content of the droplet, which both change with time. A kinetic inactivation model for β-galactosidase is developed in earlier work and calibrated using constant heating experiments (Perdana et al. 2011b). In the latter experiments, the suspended enzyme is exposed to various temperature–moisture value combinations for a specific time and the remaining enzyme activity is measured. The inactivation kinetics are described by a two-step inactivation process and the observed inactivation coefficient (k obs) is described as
where
where K 1 is the reversible unfolding equilibrium constant, k 2 is the complete denaturation rate constant, ∆∆S ‡1,w is the activation entropy difference between the unfolding and refolding reactions in pure water, ∆∆H ‡1,w is the activation enthalpy difference between the unfolding and refolding reactions in pure water, k B is Boltzmann’s constant, h is the Planck’s constant, ∆S ‡2,w is the activation entropy of complete denaturation in pure water, ∆H ‡2,w is the activation enthalpy in pure water, ∆H ‡2,m is the activation enthalpy in pure solid form (i.e. no moisture), f describes the effect of moisture content on conformational stability of the enzyme, g describes the effect of moisture content on the irreversible inactivation (second step) kinetic constant of the enzyme and T in is the intercept temperature at which k 2,w/k 2,s = 1.
Alternatively, the enzyme inactivation can also be regarded as a one-step inactivation process in which the native enzyme is irreversibly inactivated. Then
An advantage is that this approach involves only five parameters to fit instead of eight in the two-step model. The effect of the temperature is then still described using the transitional state theory as shown in Eq. 23.
Parameter Optimization and Statistical Evaluation
To directly extract the kinetics from single droplet drying experiments the following approach was taken:
-
1.
The temperature and moisture content histories of several droplets were predicted using the drying model (Eqs. 3 and 4).
-
2.
The inactivation kinetic constants were optimised to fit the measured residual enzyme activities after the drying for all droplets simultaneously.
The parameter optimisation was carried out using a non-linear least square method solved using the Levenberg–Marquardt algorithm (Seber and Wild 2005). The confidence interval of the parameters (p = 0.95) were estimated using the Hessian matrix, which was again derived from the Jacobian matrix of the solution (Richard et al. 2005). All calculations were performed with MATLAB version 7.10.
Materials and Methods
Sample Preparation
The enzyme, β-galactosidase from Aspergillus oryzae (Sigma-Aldrich, Germany) was dissolved in a buffer solution. The solution was then filtered with a 0.2-μm Minisart sterile sieve (Sartorius Stedim Biotech SA, Germany) and stored overnight in a refrigerator. The maltodextrin, with DE 4-7 (Sigma-Aldrich, Germany), was dissolved in a buffer. The buffer was prepared from 0.2 M Na2HPO4 (Sigma-Aldrich, Germany) and 0.1 M citric acid (C6H8O7) solutions (Sigma-Aldrich, Germany). The pH of the buffer was adjusted to 6.00 ± 0.01.
The feed for single droplet drying experiments was prepared by mixing 600 μL 2.5% w/w enzyme solution and 2,400 μL 25% maltodextrin solution. The feed for the laboratory-scale spray dryer was prepared by mixing 4 mL 2% w/w enzyme solution and 96 mL 20.8% w/w maltodextrin solution. A lower enzyme concentration is used during the laboratory-scale spray dryer experiments. The major reason was that a larger sample volume could be easily obtained for performing the enzyme activity test. This is allowed, since at low enzyme concentration, the inactivation kinetics of β-galactosidase is not affected by its concentration (Yamamoto and Sano 1992).
Deposited Droplet Drying Experiments
The single droplet drying experiments involved the subsequent steps: droplet generation, droplet drying, rehydration and enzyme activity measurement. A micro-dispenser was used to generate the droplet as described by Perdana et al. (2011a). The droplet was deposited on a polypropylene membrane (Akzo Nobel Faser Ag., The Netherlands) positioned on a platform from stainless steel slab; the thickness of the membrane was 0.15 mm, and the stainless steel slab was 1 mm. The droplet was then positioned in a drying tunnel (Fig. 2). By guiding the drying air through a porous medium, a uniform flow distribution could be achieved within the tunnel. The tunnel was insulated and heated with heating oil to ensure that the air temperature was constant. The temperature and relative humidity of the air bulk air was monitored using SHT75 temperature and humidity sensor (Sensiron AG, Switzerland). The temperature near the droplet was monitored using a thermocouple Type K (NiCr–NiAl; RS Component, United Kingdom) with probe diameter of 250 μm. Furthermore, the setup was equipped with a μEye 1480ME CCD camera with a lens with ×9 magnification ratio (Imaging Development Systems GMBH, Germany) to monitor the droplet geometry evolution during drying.
The single droplet drying experiments were performed using dry air (RH = 0.0%), preheated to a temperature between 80 and 110 °C and a bulk air velocity of 0.20 m/s. After drying, the resulting powder particle was dissolved in 50 μL buffer solution, stored overnight in the refrigerator, and then the enzyme activity was measured.
Laboratory-Scale Spray Drying Experiments
The enzyme solution was dried with a Buchi B-190 spray dryer (Buchi Labortechnik AG, Switzerland). The residence time of the particle inside this small spray dryer can be as short as 1 s. Based on the equipment specification, the particle diameter after drying was between 2 and 25 μm. The inlet air temperature was 180 °C, and the outlet air temperature varied between 80 and 130 °C. Subsequently, around 1 g of powder was taken and dried further in a heating chamber at 105 °C for 72 h to determine the moisture content of the powder after spray drying. Additionally, a 0.200-g powder sample was reconstituted to 3.80 mL buffer solution and analysed for its residual enzyme activity.
Measurement of the Residual Activity of β-galactosidase
The residual activity of β-galactosidase was measured using an o-nitrophenyl-β-d-galactopyranoside (ONPG) assay (Sigma-Aldrich, Germany) according to Perdana et al. (2011b). The absorbance of the samples incubated in ONPG solution was immediately measured after incubation at a wavelength 420 nm using a spectrophotometer (Beckman Coulter, Inc., USA).
Particle Size Measurement
Approximately 1 g of the spray-dried sample was dried further in a heating chamber at 105 °C for 72 h to reduce the moisture content and to avoid particle agglomeration. Afterwards, the particle size distribution of the sample was measured using Mastersizer Scirocco 2000 (Malvern Instrument LTD, England).
Results and Discussion
Droplet Geometry Evolution
Snapshots of a deposited droplet during the drying process are shown in Fig. 3. The droplet shrinks uniformly before 30 s, and then starts to develop wrinkles. The uneven shrinkage after 60 s suggests that a thin non-flowing layer is developed, which cannot accommodate a homogenous shrinkage (Walton and Mumford 1999). Instead, it collapses which leads to an irregular shape of the particle.
Drying Model
In the heat and mass transfer model, the sessile droplet is assumed to be a perfect sphere. This assumption reduces the complexity of the model and is acceptable since the initial sessile droplet has a very high contact angle (>130 °C) and also the final powder particle remains approximately spherical, as shown in Fig. 3. The predicted temperature and moisture profiles are shown in Fig. 4.
The model predicts that the moisture content at the surface decreases faster than in the centre of the droplet and reaches a moisture content close to 0% at around 35 s. This is in line with the visual observations, i.e. the occurrence of wrinkles indicating the presence of a thin dry layer. As shown in Fig. 4 (bottom), at t = 31 s, the moisture content gradient near the surface of the droplet is very steep, indicating that a very thin layer near the droplet surface is very dry. The model also predicts that the droplet radius does not change any more after approximately 60 s of drying. This is also in line with the visual observations.
The droplet temperature at the beginning (t < 40 s) of the drying process is equal to the corresponding wet bulb temperature of the heating air (Fig. 4, top). When the moisture content near the surface of the droplet decreases to less than 100 kg/m3, the droplet temperature starts to increase. At this point the water evaporation rate decreases together with the lower vapour pressure at the droplet surface (a w < 1). While the evaporation rate decreases, the heat transfer into the droplet continues and causes an accumulation of heat, observed as an increase in droplet temperature.
Predicting the Residual Enzyme Activity After Drying
The single droplet drying method is applied to dry β-galactosidase suspended in a maltodextrin matrix. The inactivation kinetics of β-galactosidase determined with independent experimental data was combined with the heat and mass transfer model to predict the residual enzyme activity after drying (Perdana et al. 2011b). Subsequently, the predicted enzyme activity is compared to the drying results. In modelling the inactivation of β-galactosidase, the pH change due to decreasing moisture content was neglected. This is allowed since most of the enzyme activity loss takes place at high moisture content where the presence of the added buffer stabilizes the pH. Furthermore, at lower moisture content, the enzyme activity loss is negligible at the time scale of drying applied. The model predictions and the experimental data are shown in Fig. 5. As shown in Fig. 5, the heat and mass transfer model using the independent kinetic inactivation model for β-galactosidase is in reasonable agreement with the experimental data.
Both the predictions and the experimental data show that the enzyme activity does not decrease during the initial drying period (<40 s) because the temperature of the droplet, which is near the (low) wet bulb temperature. Then, a rapid inactivation rate is observed, which slowly declines to result in a final enzyme activity. The subsequent rapid inactivation can be explained by an increase in particle temperature. At this point the heat transfer is not compensated by sufficient water evaporation. The increase in temperature has especially impact on the enzyme present in the centre of the droplet as the moisture content in the centre is still high as also reported for drying of other heat-sensitive products (Chen and Patel 2007; Langrish 2009). After a while the enzyme inactivation rate decreases and the residual enzyme activity in the particle is obtained. The enzyme inactivation rate decreases because of the decreasing moisture content, especially near the surface of the droplet and finally also in the centre of the droplet. Most of the residual active enzyme is located near the surface of the particle as shown in Fig. 5 (bottom). It can be concluded that the different moisture content history at different locations in the droplet determines the large differences in residual enzyme activity across the droplet radius. A strategy that might be followed to retain maximum enzyme activity is to minimize the presence of enzyme in the centre of the droplet. This can for example be achieved by drying the enzyme in a droplet that forms a hollow sphere upon drying (Etzel et al. 1996) or by applying a coating of a concentrated enzyme solution on pre-dried particles.
The results also show that the initial droplet diameter determines the residual enzyme activity to a large extent. Figure 5 indicates that the residual activity is higher for smaller droplets. Although inactivation starts earlier in a smaller droplet, the critical region is shorter (i.e. the combination of high temperature and high moisture content in the centre of the droplet) compared to that in the larger droplet. This implies that with respect to enzyme inactivation, a smaller droplet size is preferred for spray drying.
Direct Extraction of Inactivation Kinetic Parameters from Drying Experiments
The parameters describing the specific inactivation kinetics of β-galactosidase in maltodextrin may be extracted directly from the single droplet drying results. This is preferred as these experiments are much less labour intensive and can be scaled out to facilitate a high throughput approach. If the method is reliable, the parameters for β-galactosidase inactivation directly obtained from single droplet drying experiments should be similar to the ones obtained from the separate heating experiments (Perdana et al. 2011b).
Both the one-step and the two-step inactivation models were evaluated to describe the experimental drying data. The results of the parameter optimisation are compared to the parameters from the earlier study (Table 2).
It can be observed that the parameters obtained from the drying experiments differ from the parameter values from the heating experiments (Table 2). This can be explained by the fact that the inactivation during single droplet drying experiments occurs primarily during a very short critical period. This critical period is dictated by the drying history and involves temperatures and moisture content values that lead to rapid inactivation. Therefore, the parameter values are optimised such that they specifically describe the inactivation during this critical period. This explanation is further confirmed by implementing the one-step inactivation model, which is also able to describe the inactivation during drying experiments well. The data from the heating experiments were obtained at many different temperature and moisture content combinations and could be varied independently. Therefore, the values are based on a much wider data set, but having less data in the specific range that are relevant for spray drying.
Another reason for the difference between the kinetic parameters is that the parameter optimisation procedure forces the model to describe the residual enzyme activity after the drying. By doing so, any uncertainties in the heat and mass transfer model are neglected. However, from earlier observations, it was concluded that the heat and mass transfer model could predict the droplet shrinkage and the residual enzyme activity using the kinetic parameters from the heating experiments reasonably accurate. Therefore, it is believed that the uncertainties involved are not very large and that the kinetic parameters of the single droplet experiments remain valid. This conclusion is supported by laboratory spray drying experiments.
In Fig. 6 (bottom), the effect of the initial droplet diameter on the residual β-galactosidase activity after drying is shown. The figure shows that the model accurately predicts the experimental data. Therefore, it can be concluded that although the values for the parameters in the model for inactivation kinetics obtained from the drying experiments may be less precise, the inactivation kinetics are accurate enough to predict the effect of drying on the inactivation of the enzyme. This is because the critical drying period dictates the end product properties.
Table 2 shows that the values of the confidence intervals of the parameters are smaller for the one-step inactivation compared to the two-step inactivation model. Therefore, it may be concluded that the one-step inactivation model is more favourable than the two-step inactivation model to describe the effect of drying on enzyme activity loss. From practical point of view, the one-step inactivation model may be sufficient to translate the measured inactivation from single droplet experiments into useful inactivation kinetics.
Laboratory-Scale Spray Drying
The models were also applied to predict the residual enzyme activity after drying on a laboratory-scale spray dryer. The results are shown in Fig. 7. These results indicate that at an outlet air temperature below 100 °C, the enzyme is hardly inactivated upon drying, while with an outlet air temperature higher than 100 °C, the enzyme is increasingly inactivated with higher temperature as also observed by Yamamoto and Sano (1992).
The volume-weighted mean diameter (d 4,3) of the spray-dried particle is 6.94 μm, fed into the drying model to predict the residual enzyme activity. By assuming that the volumetric droplet shrinkage is equal to the amount of water removed, the initial droplet diameter was estimated at 11.8 μm (initial moisture content 80% w/w, Langrish 2009).
The model can predict the drying results reasonably accurate, but at temperatures between 100 and 120 °C, the predicted value of the residual activity of β-galactosidase is slightly lower than the experimental results. This may be due to the lower initial droplet size in reality due to non-ideal shrinkage leading to more rapid drying and thus lower inactivation (see also Fig. 3).
Furthermore, Fig. 7 shows that there is only a small difference between the two inactivation models at temperatures larger than 100 °C. This is probably because the inactivation kinetic constant of the one-step inactivation model increases more quickly with temperature. This may lead to an overestimation of the inactivation kinetic constant at high temperatures.
Conclusions
A newly developed, small-scale experimental setup to mimic spray drying was presented which involves the drying of single droplets deposited on a hydrophobic flat plate. This approach ensures rapid and inexpensive trials while maintaining key parameters similar to the process condition on spray drying. In this study, the setup is used to evaluate the inactivation of β-galactosidase during drying.
To describe the physical and chemical changes during drying, a model based on heat and mass transfer is presented. The model, combined with the inactivation kinetics of β-galactosidase from separate heating experiments, was used to predict the loss in enzyme activity after drying. It is found that the model can provide a reasonably accurate prediction on the residual enzyme activity.
It was also shown that the inactivation kinetics of β-galactosidase can be directly extracted from the single droplets drying experiments rather than using the kinetics from separate heating experiments. The parameters that were obtained in this way were used to predict other experimental results both from other single droplet drying experiments and from a laboratory-scale spray dryer. The new inactivation kinetics provides reasonably accurate prediction on the residual enzyme activity for both procedures.
Nomenclature | ||
---|---|---|
A | Area | m2 |
a w | Water activity | – |
c p | Heat capacity | J kg−1 K−1 |
C | Concentration | kg m–3 |
C g | Constant in GAB sorption model | – |
d | Diameter (2R d) | m |
D | Diffusion coefficient | m2 s−1 |
E a | Arrhenius-type diffusion activation energy | J mol−1 |
f | Parameter to describe the effect of moisture content on conformational stability of the enzyme | – |
g | Parameter to describe the effect of moisture content on the irreversible inactivation (second step) kinetic constant of the enzyme | – |
h | Planck’s constant (6.626 × 10−34) | J s−1 |
h | Convective heat transfer coefficient | J s−1 m−2 K−1 |
∆H lv | Enthalpy of evaporation | J kg−1 |
∆H ‡ | Activation enthalpy | J mol−1 |
∆∆H ‡ | Activation enthalpy difference between unfolding and refolding reaction | J mol−1 |
J | Evaporation rate | kg s−1 |
kB | Boltzmann’s constant (1.380 × 10−23) | J K−1 |
k obs | Observed inactivation kinetic constant of β-galactosidase | s−1 |
k 2 | Irreversible complete denaturation rate constant of β-galactosidase | s−1 |
k c | Mass transfer coefficient | m s−1 |
K g | Constant in GAB sorption model | – |
K 1 | Unfolding equilibrium constant of β-galactosidase | s s−1 |
L | Length | m |
m | Mass | kg |
m u | Parameter to describe the effect of moisture content on unfolding equilibrium of β-galactosidase | – |
M w | Molecular weight of water (18∙10−3) | kg mol−1 |
n | Number of partition | – |
p | Uncertainty of the parameters | – |
p i | Parameter to describe the effect of moisture content on irreversible complete denaturation rate constant of β-galactosidase | – |
P | Pressure | Pa |
Pr | Prandtl number | – |
Q | Heat | J s−1 |
r | Distance in radial coordinate | m |
R | Ideal gas constant (8.314) | J mol−1 K−1 |
Re | Reynolds number | – |
R d | Droplet radius | m |
∆S ‡ | Activation entropy | J mol−1 K−1 |
∆∆S ‡ | Activation entropy difference between unfolding and refolding reaction | J mol−1 K−1 |
Sc | Schmidt number | – |
t | Time | s |
T | Temperature | °C |
u | Velocity | m s−1 |
V | Volume | m3 |
x | Distance in Cartesian coordinate | m |
x w | Mass fraction of water | kg kg−1 |
X w | Moisture content | kg kg−1 dry matter |
X wm | Monolayer moisture content in GAB sorption model | kg kg−1 dry matter |
y | Distance in Cartesian coordinate | m |
z | Distance in Cartesian coordinate | m |
Z | Thickness | m |
Greek symbols | ||
δ | Hydrodynamic boundary layer thickness | m |
δ t | Thermal boundary layer thickness | m |
λ | Thermal conductivity | J s−1 m−1 K−1 |
μ | Dynamic viscosity | Pa s |
ρ | Density | kg m−3 |
υ | Kinematic viscosity | m2 s−1 |
Subscript | ||
a | Air | |
avg | Average | |
cond | Conduction | |
d | Droplet | |
int | Intercept | |
m | Very dry matrix | |
obs | Observed | |
p | Flat plate for droplet deposition | |
ref | Reference | |
s | Solute | |
sat | Saturated | |
w | Water | |
0 | Initial | |
∞ | Bulk air |
References
Adhikari, B., Howes, T., Bhandari, B. R., & Truong, V. (2000). Experimental studies and kinetics of single drop drying and their relevance in drying of sugar-rich foods: A review. International Journal of Food Properties, 3(3), 323–351.
Ali Al Zaitone, B., & Tropea, C. (2011). Evaporation of pure liquid droplets: Comparison of droplet evaporation in an acoustic field versus glass-filament. Chemical Engineering Science, 66(17), 3914–3921.
Bolz, R. E. & Tuve, G. L. (1973). CRC handbook of tables for applied engineering science. CRC Press, Cleveland, Ohio, USA.
Chen, X. D., & Patel, K. C. (2007). Micro-organism inactivation during drying of small droplets or thin-layer slabs—A critical review of existing kinetics models and an appraisal of the drying rate dependent model. Journal of Food Engineering, 82(1), 1–10.
Chuchottaworn, P., Fujinami, A., & Asano, K. (1984). Experimental study of evaporation of a volatile pendant drop under high mass flux conditions. Journal of Chemical Engineering Japan, 17, 7–13.
Coumans, W. J. (2000). Models for drying kinetics based on drying curves of slabs. Chemical Engineering and Processing, 39(1), 53–68.
Crank, J. (1990). The mathematics of diffusion. London, UK: Oxford University Press.
Etzel, M. R., Suen, S. Y., Halverson, S. L., & Budijono, S. (1996). Enzyme inactivation in a droplet forming a bubble during drying. Journal of Food Engineering, 27(1), 17–34.
Fang, Z., & Bhandari, B. (2010). Encapsulation of polyphenols—A review. Trends in Food Science & Technology, 21(10), 510–523.
Farid, M. (2003). A new approach to modelling of single droplet drying. Chemical Engineering Science, 58(13), 2985–2993.
Filková, I., Huang, L.X. & Mujumdar, A. (2006). Industrial spray drying systems. In: Handbook of Industrial Drying, 3rd Ed. Boca Raton: CRC Press.
Gianfrancesco, A., Turchiuli, C., Flick, D., & Dumoulin, E. (2010). CFD modeling and simulation of maltodextrin solutions spray drying to control stickiness. Food and Bioprocess Technology, 3(6), 946–955.
Goff, J. A., & Gratch, S. (1946). Low-pressure properties of water from -160 to 212 F, in Transactions of the American Society of heating and ventilating engineers. The 52nd annual meeting of the American society of heating and ventilating engineers. New York: 95–122.
Goula, A. M., & Adamopoulos, K. G. (2004). Influence of spray drying conditions on residue accumulation-simulation using CFD. Drying Technology, 22(5), 1107–1128.
Incropera, F. P., & De Witt, D. P. (1985). Fundamentals of heat and mass transfer (2nd ed.). New York: Wiley.
Kakac, S., & Yener, Y. (1993). Heat conduction. Washington: Taylor & Francis.
Langrish, T. (2009). Degradation of vitamin C in spray dryers and temperature and moisture content profiles in these dryers. Food and Bioprocess Technology, 2(4), 400–408.
Li, X., Anton, N., Arpagaus, C., Belleteix, F., & Vandamme, T. F. (2010). Nanoparticles by spray drying using innovative new technology: The Büchi Nano Spray Dryer B-90. Journal of Controlled Release, 147(2), 304–310.
Luyben, K. C. A. M., Liou, J. K., & Bruin, S. (1982). Enzyme degradation during drying. Biotechnology and Bioengineering, 24(3), 533–552.
Meerdink, G., & van't Riet, K. (1991). Inactivation of thermostable [alpha]-amylase during drying. Journal of Food Engineering, 14(2), 83–102.
Mezhericher, M., Levy, A., & Borde, I. (2008). Heat and mass transfer of single droplet/wet particle drying. Chemical Engineering Science, 63(1), 12–23.
Millqvist-Fureby, A., Malmsten, M., & Bergenståhl, B. (1999). Spray-drying of trypsin—surface characterisation and activity preservation. International Journal of Pharmaceutics, 188(2), 243–253.
Mosaad, M. (1999). Laminar forced convection conjugate heat transfer over a flat plate. Heat and Mass Transfer, 35(5), 371–375.
Peighambardoust, S. H., Golshan Tafti, A., & Hesari, J. (2011). Application of spray drying for preservation of lactic acid starter cultures: A review. Trends in Food Science & Technology, 22(5), 215–224.
Perdana, J., Fox, M. B., Schutyser, M. A. I., & Boom, R. M. (2011a). Single-droplet experimentation on spray drying: Evaporation of a sessile droplet. Chemical Engineering and Technology, 34(7), 1151–1158.
Perdana, J., Fox, M. B., Schutyser, M. A. I. & Boom, R. M. (2011b). Enzyme inactivation kinetics: Coupled effects of temperature and moisture content. Food Chemistry (in press).
Quirijns, E. J., Boxtel, A. J. B., Loon, W. K. P., & Straten, G. (2005). Sorption isotherms, GAB parameters and isosteric heat of sorption. Journal of the Science of Food and Agriculture, 85(11), 1805–1814.
Ranz, W. E., & Marshall, J. M. (1952). Evaporation from drops, Part II. Chem. Eng. Prog., 48(3), 141–146 (Part I); 48(4), 173–l 80 {Part II).
Räderer, M., Besson, A., & Sommer, K. (2002). A thin film dryer approach for the determination of water diffusion coefficients in viscous products. Chemical Engineering Journal, 86(1–2), 185–191.
Ré, M. I. (1998). Microencapsulation by spray drying. Drying Technology: An International Journal, 16(6), 1195–1236.
Richard, C., Aster, B. B. & Clifford, H. T. (2005). Appendix C. Review of vector calculus. In: International Geophysics, pp. 273–280. New York: Academic Press.
Sansone, F., Mencherini, T., Picerno, P., d'Amore, M., Aquino, R. P., & Lauro, M. R. (2011). Maltodextrin/pectin microparticles by spray drying as carrier for nutraceutical extracts. Journal of Food Engineering, 105(3), 468–476.
Schiffter, H., & Lee, G. (2007). Single-droplet evaporation kinetics and particle formation in an acoustic levitator. Part 1: Evaporation of water microdroplets assessed using boundary-layer and acoustic levitation theories. Journal of Pharmaceutical Sciences, 96(9), 2274–2283.
Schlichting, H., & Gersten, K. (2000). Boundary-layer theory (8th ed.). Berlin: Spinger.
Seber, G. A. F. & Wild, C. J. (2005). Computational methods for nonlinear least squares. In: Nonlinear regression, pp. 619–660. New York: Wiley.
Sloth, J., Kiil, S., Jensen, A. D., Andersen, S. K., Jørgensen, K., Schiffter, H., & Lee, G. (2006). Model based analysis of the drying of a single solution droplet in an ultrasonic levitator. Chemical Engineering Science, 61(8), 2701–2709.
Straatsma, H., Verschueren, M., Gunsing, M., Verdurmen, R. & Jong, P. d. (2007). CFD simulation of spray drying of food products. In: Computational fluid dynamics in food processing, pp. 249–286. New York: CRC Press.
Thirumaleshwar, M. (2009). Fundamentals of heat and mass transfer. New Delhi: Dorling Kindersley.
Vehring, R., Foss, W. R., & Lechuga-Ballesteros, D. (2007). Particle formation in spray drying. Journal of Aerosol Science, 38(7), 728–746.
Walton, D. E., & Mumford, C. J. (1999). The morphology of spray-dried particles: The effect of process variables upon the morphology of spray-dried particles. Chemical Engineering Research and Design, 77(5), 442–460.
Wijlhuizen, A. E., Kerkhof, P. J. A. M., & Bruin, S. (1979). Theoretical study of the inactivation of phosphatase during spray drying of skim-milk. Chemical Engineering Science, 34(5), 651–660.
Wu, W. D., Lin, S. X., & Chen, X. D. (2011). Monodisperse droplet formation through a continuous jet break-up using glass nozzles operated with piezoelectric pulsation. AICHE Journal, 57(6), 1386–1392.
Xin Huang, L., Filkova, I. & Mujumdar, A. (2006). Industrial spray drying systems. In: Handbook of industrial drying, 3rd ed. New York: CRC Press.
Yamamoto, S., & Sano, Y. (1992). Drying of enzymes: enzyme retention during drying of a single droplet. Chemical Engineering Science, 47(1), 177–183.
Yoshioka, S., Aso, Y., Izutsu, K-i, & Kojima, S. (1994). Is stability prediction possible for protein drugs? Denaturation kinetics of β-galactosidase in solution. Pharmaceutical Research, 11(12), 1721–1725.
Acknowledgement
The authors thank Advanced Chemical Technologies for Sustainability (ACTS)–Netherlands Organization for Scientific Research (NWO) for financial aid through Process on a Chip (PoaC) program.
Open Access
This article is distributed under the terms of the Creative Commons Attribution Noncommercial License which permits any noncommercial use, distribution, and reproduction in any medium, provided the original author(s) and source are credited.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This is an open access article distributed under the terms of the Creative Commons Attribution Noncommercial License (https://creativecommons.org/licenses/by-nc/2.0), which permits any noncommercial use, distribution, and reproduction in any medium, provided the original author(s) and source are credited.
About this article
Cite this article
Perdana, J., Fox, M.B., Schutyser, M.A.I. et al. Mimicking Spray Drying by Drying of Single Droplets Deposited on a Flat Surface. Food Bioprocess Technol 6, 964–977 (2013). https://doi.org/10.1007/s11947-011-0767-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11947-011-0767-4