Abstract
Analogizing with the definition of thermal efficiency of a heat exchanger, the entransy dissipation efficiency of a heat exchanger is defined as the ratio of dimensionless entransy dissipation rate to dimensionless pumping power of the heat exchanger. For the constraints of the total tube volume and total tube surface area of the heat exchanger, the constructal optimization of an H-shaped multi-scale heat exchanger is carried out by taking entransy dissipation efficiency maximization as optimization objective, and the optimal construct of the H-shaped multi-scale heat exchanger with maximum entransy dissipation efficiency is obtained. The results show that for the specified total tube volume of the heat exchanger, the optimal constructs of the first order T-shaped heat exchanger based on the maximizations of the thermal efficiency and entransy dissipation efficiency are obviously different with the lower mass flow rates of the cold and hot fluids. For the H-shaped multi-scale heat exchanger, the entransy dissipation efficiency decreases with the increase in mass flow rate when the heat exchanger order is fixed; for the specified dimensionless mass flow rate M (M<32.9), the entransy dissipation efficiency decreases with the increase in the heat exchanger order. The performance of the multi-scale heat exchanger is obviously improved compared with that of the single-scale heat exchanger. Moreover, the heat exchanger subjected to the total tube surface area constraint is also discussed in the paper. The optimization results obtained in this paper can provide a great compromise between the heat transfer and flow performances of the heat exchanger, provide some guidelines for the optimal designs of heat exchangers, and also enrich the connotation of entransy theory.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Bejan A. The concept of irreversibility in heat exchanger design: counterflow heat exchangers for gas-to-gas applications. Tran ASME J Heat Trans, 1977, 99(3): 374–380
Bejan A. Second law analysis in heat transfer. Energy, 1980, 5(8-9): 720–732
Bejan A. Entropy Generation through Heat and Fluid Flow. New York: Wiley, 1982
Bejan A. Entropy Generation Minimization. Boca Raton FL: CRC Press, 1996
Shah R K, Sekulic D P. Fundamentals of Heat Exchanger Design. Hoboken: Wiley, 2003
Xu Z, Yang S, Chen Z. Variational solution of optimum parameter distributions in heat exchanger (in Chinese). J Chem Indust Eng, 1995, 46(1): 75–80
Xiong D, Li Z, Guo Z. Analysis on effectiveness and entropy generation in heat exchangers (in Chinese). J Eng Thermophys, 1997, 18(1): 90–94
Hesselgreaves J E. Rationalisation of second law analysis of heat exchanger. Int J Heat Mass Trans, 2000, 43(22): 4189–4204
Shah R K, Skiepko T. Entropy generation extremum and their relationship with heat exchanger effectiveness-number of transfer unit behavior for complex flow arrangements. Trans ASME J Heat Trans, 2004, 126(6): 994–1002
Guo J, Cheng L, Xu M. Optimization design of shell-and-tube heat exchanger by entropy generation minimization and genetic algorithm. Appl Therm Eng, 2009, 29(14-15): 2954–2960
Guo J, Cheng L, Xu M. Multi-objective optimization of heat exchanger design by entropy generation minimization. Trans ASME J Heat Trans, 2010, 132(8): 081801
Guo Z, Zhu H, Liang X. Entransy-A physical quantity describing heat transfer ability. Int J Heat Mass Trans, 2007, 50(13/14): 2545–2556
Li Z, Guo Z. Field Synergy Principle of Heat Convection Optimization. Beijing: Science Press, 2010
Guo Z, Cheng X, Xia Z. Least dissipation principle of heat transport potential capacity and its application in heat conduction optimization. Chin Sci Bull, 2003, 48(4): 406–410
Han G, Zhu H, Cheng X, et al. Transfer similarity among heat conduction, elastic motion and electric conduction (in Chinese). J Eng Thermophys, 2005, 26(6): 1022–1024
Han G, Guo Z. Physical mechanism of heat conduction ability dissipation and its analytical expression (in Chinese). Proc CSEE, 2007, 27(17): 98–102
Zhu H, Chen J, Guo Z. Electricity and thermal analogous experimental study for entransy dissipation extreme principle (in Chinese). Prog Natural Sci, 2007, 17(12): 1692–1698
Chen L. Progress in entransy theory and its applications. Chin Sci Bull, 2012, 57(34): 4404–4426
Liu H, Guo Z, Meng J. Analyses for entransy dissipation and heat resistance in heat exchangers (in Chinese). Prog Natural Sci, 2008, 18(10): 1186–1190
Liu X, Guo Z. A novel method for heat exchanger analysis (in Chinese). Acta Phys Sin, 2009, 58(7): 4766–4771
Guo Z, Liu X, Tao W, Shah R K. Effectiveness-thermal resistance method for heat exchanger design and analysis. Int J Heat Mass Trans, 2010, 53(13–14): 2877–2884
Song W, Meng J, Liang X, et al. Demonstration of uniformity principle of temperature difference field for one-dimensional heat exchangers (in Chinese). J Chem Indus Eng, 2008, 59(10): 2460–2464
Xia S, Chen L, Sun F. Optimization for entransy dissipation minimization in heat exchanger. Chin Sci Bull, 2009, 54(19): 3587–3595
Guo J, Xu M, Cheng L. Principle of equipartition of entransy dissipation for heat exchanger design. Sci China Tech Sci, 2010, 53(5): 1309–1314
Guo J, Xu M, Cheng L. The entransy dissipation minimization principle under given heat duty and heat transfer area conditions. Chin Sci Bull, 2011, 56(19): 2071–2076
Liu X, Meng J, Guo Z. Entropy generation extremum and entransy dissipation extremum for heat exchanger optimization. Chin Sci Bull, 2009, 54(6): 943–947
Qian X, Li Z. Analysis of entransy dissipation in heat exchangers. Int J Therm Sci, 2011, 50(4): 608–614
Cheng X, Zhang Q, Liang X. Analyses of entransy dissipation, entropy generation and entransy-dissipation-based thermal resistance on heat exchanger optimization. Appl Therm Eng, 2012, 38: 31–39
Guo J, Cheng L, Xu M. Entransy dissipation number and its application to heat exchanger performance evaluation. Chin Sci Bull, 2009, 54(15): 2708–2713
Guo J, Xu M, Cheng L. Optimization design of plate-fin heat exchanger based on entransy dissipation number minimization (in Chinese). J Eng Thermophys, 2011, 32(5): 827–831
Li M, Chen L, Xu M. Application of entransy dissipation theory in optimization design of shell-and-tube heat exchanger (in Chinese). J Eng Thermophys, 2010, 31(7): 1189–1192
Chen L, Chen Q, Li Z, Guo Z. Optimization for a heat exchanger couple based on the minimum thermal resistance principle. Int J Heat Mass Trans, 2009, 52(21-22): 4778–4784
Chen Q, Wu J, Wang M, et al. A comparison of optimization theories for energy conservation in heat exchanger groups. Chin Sci Bull, 2011, 56(4–5): 449–454
Qian X, Li Z, Li Z. Entransy-dissipation-based thermal resistance analysis of heat exchanger networks. Chin Sci Bull, 2011, 56(31): 3289–3295
Cheng X, Liang X. Computation of effectiveness of two-stream heat exchanger networks based on concepts of entropy generation, entransy dissipation and entransy-dissipation-based thermal resistance. Energy Convers Mgmt, 2012, 58: 163–170
Xu Y, Chen Q. Minimization of mass for heat exchanger networks in spacecrafts based on the entransy dissipation theory. Int J Heat Mass Transfer, 2012, 55(19–20): 5148–5156
Xu M, Cheng L, Guo J. An application of entransy dissipation theory to heat exchanger design (in Chinese). J Eng Thermophys, 2009, 30(12): 2090–2092
Li X, Guo J, Xu M, et al. Entransy dissipation minimization for optimization of heat exchanger design. Chin Sci Bull, 2011, 56(20): 2174–2178
Guo J, Xu M, Cheng L. The influence of viscous heating on the entransy in two-fluid heat exchangers. Sci China Tech Sci, 2011, 54(5): 1267–1274
Guo J, Xu M, Cheng L. Effect of temperature-dependent viscosity on the entransy of both fluids in heat exchangers (in Chinese). Chin Sci Bull, 2011, 56: 1934–1939
Guo J, Xu M. The application of entransy dissipation theory in optimization design of heat exchanger. Appl Therm Eng, 2012, 36: 227–235
Wei S, Chen L, Sun F. “Volume-point” heat conduction constructal optimization with entransy dissipation minimization objective based on rectangular element. Sci China Ser E-Tech Sci, 2008, 51(8): 1283–1295
Wei S, Chen L, Sun F. Constructal multidisciplinary optimization of electromagnet based on entransy dissipation minimization. Sci China Ser E-Tech Sci, 2009, 52(10): 2981–2989
Xie Z, Chen L, Sun F. Constructal optimization for geometry of cavity by taking entransy dissipation minimization as objective. Sci China Ser E-Tech Sci, 2009, 52(12): 3504–3513
Xie Z, Chen L, Sun F. Constructal optimization on T-shaped cavity based on entransy dissipation minimization. Chin Sci Bull, 2009, 54(23): 4418–4427
Wei S, Chen L, Sun F. Constructal optimization of discrete and continuous-variable cross-section conducting path based on entransy dissipation rate minimization. Sci China-Tech Sci, 2010, 53(6): 1666–1677
Xiao Q, Chen L, Sun F. Constructal entransy dissipation rate minimization for “disc-to-point” heat conduction. Chin Sci Bull, 2011, 56(1): 102–112
Xiao Q, Chen L, Sun F. Constructal entransy dissipation rate minimization for umbrella-shaped assembly of cylindrical fins. Sci China Tech Sci, 2011, 54(1): 211–219
Xiao Q, Chen L, Sun F. Constructal entransy dissipation rate and flow-resistance minimizations for cooling channels. Sci China Tech Sci, 2010, 53(9): 2458–2468
Chen L, Wei S, Sun F. Constructal entransy dissipation rate minimization of a disc. Int J Heat Mass Trans, 2011, 54(1–3): 210–216
Wei S, Chen L, Sun F. Constructal entransy dissipation rate minimization of round tube heat exchanger cross-section. Int J Therm Sci, 2011, 50(7): 1285–1292
Xie Z, Chen L, Sun F. Comparative study on constructal optimizations of T-shaped fin based on entransy dissipation rate minimization and maximum thermal resistance minimization. Sci China Tech Sci, 2011, 41(7): 962–970
Xiao Q, Chen L, Sun F. Constructal design for a steam generator based on entransy dissipation extremum principle. Sci China Tech Sci, 2011, 54(6): 1462–1468
Xiao Q, Chen L, Sun F. Constructal entransy dissipation rate minimization for a heat generating volume cooled by forced convection. Chin Sci Bull, 2011, 56(27): 2966–2973
Feng H, Chen L, Sun F. “Volume-point” heat conduction constructal optimization based on entransy dissipation rate minimization with three-dimensional cylindrical element and rectangular and triangular elements at micro and nanoscales. Sci China Tech Sci, 2012, 55(3): 779–794
Feng H, Chen L, Sun F. Constructal entransy dissipation rate minimization for leaf-like fins. Sci China Tech Sci, 2012, 55(2): 515–526
Bejan A. Shape and Structure, from Engineering to Nature. Cambridge, UK: Cambridge University Press, 2000
Bejan A, Lorente S. Thermodynamic optimization of flow geometry in mechanical and civil engineering. J Non-Eq Thermodyn, 2001, 26(4): 305–354
Bejan A, Lorente S. Constructal theory of generation of configuration in nature and engineering. J Appl Phys, 2006, 100(4): 041301
Bejan A, Merkx G, Eds. Constructal Theory of Social Dynamics. 1st ed. New York: Springer, 2007
Bejan A, Lorente S. Design with Constructal Theory. New Jersey: Wiley, 2008
Bejan A, Lorente S, Miguel A, et al. Constructal Human Dynamics, Security & Sustainability. Amsterdam: IOS Press, 2009
Bejan A, Zane P J. Design in Nature. New York: Doubleday, 2012
Chen L. Progress in study on constructal theory and its application. Sci China Tech Sci, 2012, 55(3): 802–820
da Silva A K, Lorente S, Bejan A. Constructal multi-scale tree-shaped heat exchanger. J Appl Phys, 2004, 96(3): 1709–1718
Zimparov V D, da Silva A K, Bejan A. Constructal tree-shaped parallel flow heat exchangers. Int J Heat Mass Trans, 2006, 49(23-24): 4558–4566
da Silva A K, Bejan A. Dendritic counterflow heat exchanger experiments. Int J Therm Sci, 2006, 45(9): 860–869
Chen Y, Cheng P. An experimental investigation on the thermal efficiency of fractal tree-like microchannel nets. Int Comm Heat Mass Trans, 2005, 32(7): 931–938
Zhang C, Chen Y, Yang Y, et al. Thermal analysis of constructal tree-shaped minichannel heat sink (in Chinese). J Eng Thermophys, 2010, 31(5): 824–826
Chen Y, Zhang C, Shi M, Yang Y. Thermal and hydrodynamic characteristics of constructal tree-shaped minichannel heat sink. AIChE J, 2010, 56(8): 2018–2029
Zhang C, Chen Y, Wu R, Shi M. Flow boiling in constructal tree-shaped minichannel network. Int J Heat Mass Trans, 2011, 54(1-3): 202–209
Yang S, Tao W. Heat Tansfer. 4th ed. Beijing: Higher Education Press, 2006
Bejan A, Rocha L A O, Lorente S. Thermodynamic optimization of geometry: T- and Y-shaped constructs of fluid streams. Int J Therm Sci, 2000, 39(9): 949–960
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Feng, H., Chen, L., Xie, Z. et al. Constructal optimization for H-shaped multi-scale heat exchanger based on entransy theory. Sci. China Technol. Sci. 56, 299–307 (2013). https://doi.org/10.1007/s11431-012-5097-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11431-012-5097-x