A procedure for the numerical analysis of the thermoviscoelastoplastic stress–strain state of thin layered shells of revolution under axisymmetric loading is proposed. Constitutive equations that incorporate the third deviatoric stress invariant are used to describe the inelastic deformation of isotropic materials. Numerical results are analyzed
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
L. M. Kachanov, Fundamentals of the Theory of Plasticity, Dover, New York (2004).
I. A. Motovilovets and V. I. Kozlov, Thermoelasticity, Vol. 1 of the six-volume series Mechanics of Coupled Fields in Structural Members [in Russian], Naukova Dumka, Kyiv (1987).
V. V. Novozhilov, Theory of Elasticity, Pergamon Press, Oxford (1961).
Yu. N. Shevchenko, M. E. Babeshko, and R. G. Terekhov, Thermoviscoelastoplastic Processes of Combined Deformation of Structural Members [in Russian], Naukova Dumka, Kyiv (1992).
M. E. Babeshko and Yu. N. Shevchenko, “Describing the thermoelastoplastic deformation of compound shells under axisymmetric loading with allowance for the third invariant of stress deviator,” Int. Appl. Mech., 46, No. 12, 1362–1371 (2010).
J. Betten, “Mathematical modeling of material behaviour under creep conditions,” Appl. Mech. Rev., 54, No. 2, 107–132 (2001).
G. G. Chen and T. R. Hsu, “A mixed explicit-implicit (EL) algorithms for creep stress analysis,” Int. J. Numer. Meth. Eng., 26, No. 2, 511–524 (1988).
A. Z. Galishin and Yu. N. Shevchenko, “Determining the axisymmetric thermoelastoplastic state of thin shells with allowance for the third invariant of the deviatoric stress tensor,” Int. Appl. Mech., 49, No. 6, 675–684 (2013).
R. Hill, The Mathematical Theory of Plasticity, Clarendon Press, Oxford (1950).
S. Murakami and N. Ohno, “A continuum theory of creep and creep damage,” in: Creep in Structures, Springer-Verlag, Berlin (1981), pp. 422–444.
F. K. G. Odquist, Mathematical Theory of Creep and Creep Rupture, Clarendon Press, Oxford (1966).
Yu. N. Shevchenko and M. E. Babeshko, “The thermoviscoelastoplastic state of laminated shells of revolution under axisymmetric loading,” in: Proc. 6th Int. Congr. on Thermal Stresses (May 26–29, 2005, Vienna, Austria), 1, Vienna (2005), pp. 237–230.
A. Yu. Shevchenko, M. V. Banyas, and I. K. Senchenkov, “A variant of the equations of nonisothermal plastic flow,” Int. Appl. Mech., 48, No. 5, 602–607 (2012).
Yu. N. Shevchenko, R. G. Terekhov, and N. N. Tormakhov, “Elastoplastic deformation of elements of an isotropic solid along paths of small curvature: Constitutive equations incorporating the stress mode,” Int. Appl. Mech., 43, No. 6, 621–630 (2007).
Yu. N. Shevchenko and N. N. Tormakhov, “Thermoviscoplastic deformation along paths of small curvature: Constitutive Equations including the third deviatoric stress invariant,” Int. Appl. Mech., 48, No. 6, 688–699 (2012).
A. Zolochevsky, “Creep of isotropic and anisotropic materials with different behaviour in tension and compression,” in: M. Zyczkowski (ed.), Creep in Structures, Springer-Verlag, Berlin (1991), pp. 217–220.
A. Zolochevsky, A. Galishin, S. Sklepus, and G. Z. Voyiadjis, “Analysis of creep deformation and creep damage in thin-walled branches shells from materials with different behavior in tension and compression,” Int. J. Solids Struct., 44, No. 16, 5075–5100 (2007).
A. Zolochevsky, S. Sklepus, T. H. Hyde, A. A. Becker, and S. Paravali, “Numerical modeling of creep and creep damage in thin plates of arbitrary shape from materials with different behavior in tension and compression under plane stress condition,” Int. J. Numer. Meth. Eng., 80, No. 11, 1406–1436 (2009).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Prikladnaya Mekhanika, Vol. 50, No. 6, pp. 14–26, November–December 2014.
Rights and permissions
About this article
Cite this article
Babeshko, M.E., Shevchenko, Y.N. Studying the Axisymmetric Thermoviscoelastoplastic Deformation of Layered Shells Taking into Account the Third Deviatoric Stress Invariant. Int Appl Mech 50, 615–626 (2014). https://doi.org/10.1007/s10778-014-0660-8
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10778-014-0660-8