Abstract
Global pollution is calling for advanced methods to remove contaminants from water and wastewater, such as TiO2-assisted photocatalysis. The environmental applications of titanium dioxide have started after the initial TiO2 application for water splitting by Fujishima and Honda in 1972. TiO2 is now used for self-cleaning surfaces, air and water purification systems, microbial inactivation and selective organic conversion. The synthesis of titanium dioxide nanomaterials with high photocatalytic activity is actually a major challenge. Here we review titanium dioxide photocatalysis with focus on mechanims, synthesis, and applications. Synthetic methods include sol-gel, sonochemical, microwave, oxidation, deposition, hydro/solvothermal, and biological techniques. Applications comprise the production of energy, petroleum recovery, and the removal of microplastics, pharmaceuticals, metals, dyes, pesticides, and of viruses such as the severe acute respiratory syndrome coronavirus 2.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
The past several decades have seen an ever-increasing rate of scientific and engineering innovations which has also brought with it the undesirable effects of anthropogenic activities such as pollution, and the proliferation of antibiotic-resistant microbes (Ojemaye et al. 2020; Maganha de Almeida Kumlien et al. 2021) and their associated health hazards. While concerted efforts have been taken to decrease the detrimental effects of such pollutants on the health and wellbeing of the environment, much attention has been on pollution mitigation via adsorption or oxidative mineralization (Daghrir et al. 2013). To this end, nanoparticles have been successfully demonstrated to attenuate pollutants of varying characteristics such as trace, organic, inorganic and biological (Villaseñor and Ríos 2017). Numerous candidates are deployed in environmental endeavours including oxides of transition metals (zinc oxide, titanium oxide, iron oxide, aluminium oxide) (Udom et al. 2013; Fajardo et al. 2014; Haider et al. 2017; Hitam and Jalil 2020), sulphides (zinc sulphide, cadmium sulphide) (Lee and Wu 2017; Theerthagiri et al. 2017), nitrides (graphitic carbon nitrides) (Zhang et al. 2018; Zhu et al. 2020), carbon allotropes (Madima et al. 2020; Long et al. 2021), nanocomposites with noble metals (Liu et al. 2017; Prakash et al. 2018) and other transition metal compounds (López et al. 2021). However, the chief criterion for selecting the best nanoparticle for a certain application is based on the cost-effectiveness, chemical stability and recoverability. Consequently, nanosized titanium dioxide (TiO2) has become a chief candidate for pollution mitigation application as a photocatalyst, adsorbent or electrocatalyst.
Tremendous development in TiO2 nanoparticles synthesis techniques has enabled its application in an array of fields such as water purification (Jézéquel and Chu 2005)(Lee and Park 2013), carbon dioxide reduction (Ola and Maroto-Valer 2015), water splitting (Ismael 2020), air pollution mitigation (Toma et al. 2004) (Lyu et al. 2014), food (Boutillier et al. 2021) and microbial decontamination/surface disinfection (Laxma Reddy et al. 2017) with promising results. This has also partly been motivated by the eco-friendly, self-cleaning/sterilizing, stable and inert nature of titanium dioxide. In addition, bulk-scale titanium dioxide possesses little to no environmental application and is mostly employed as a dye/pigment (Weir et al. 2012).
A variety of TiO2 nanoparticles such as dendrites (Sun et al. 2011), anodic grids (de Freitas et al. 2011), nanodots (Zhang et al. 2017), powders (Yildiz et al. 2020), 2D nanosheets (Chen et al. 2020), hollow spheres (Su et al. 2020), nanoflowers (Harris et al. 2020), nanorods (Diao et al. 2021) and nanobelts have been synthesized through various techniques like sol–gel method, hydro (solvo)-thermal method and microwave methods. Considering the diversiform application areas of titanium dioxide nanoparticles in the environment, this work tries to provide a consolidated review of various synthesis techniques that can be applied for the production of nano-titanium dioxide and their application as photocatalysts for pollutants (heavy metals, dyes and microplastic) removal, electrocatalysts for energy production (water splitting and carbon dioxide reforming), antimicrobial agents, nanomedicine and oil recovery which will be discussed towards the latter sections of the work.
While many reviews currently exist on the various techniques for synthesis of TiO2 nanoparticles, some excellent reviews in this field include the works such as Daghrir et al. (2013), Wang et al. (2014), and Gopinath et al. (2020) that have covered numerous articles until recent past. However, with tremendous improvement in nanoparticle synthesis techniques, a latest and more comprehensive review on the synthesis and application of titanium dioxide is needed and this work has been framed towards addressing this endeavour.
Mechanism of titanium dioxide photocatalysis
Being a semiconductor, titanium dioxide (TiO2) comprises a small energy difference between the conduction and valence bands. Electrons that are present in the valence band get excited to the conduction band when light (ultraviolet) falls on its surface. This phenomenon leads to the formation of both negative and positive charges on the semiconductor surface. Titanium dioxide has a band gap (3–3.2 eV) with a maximum absorption wavelength of 400 nm. The entire phenomenon of electron excitation is depicted in Fig. 1. Constant exposure to light results in the formation of high temperature on the titanium dioxide surface, and this, in turn, results in the degradation of pollutants in the water system. The degradation of pollutants with the help of dissolved oxygen present in the water is depicted in Eqs. (1–3). Hydroxyl radicals formed during these reactions also help in the degradation of pollutants via the photocatalytic degradation mechanism (Eq. 4) (Yao et al. 2017). Here they undergo protonation and end up in the formation of hydroperoxyl compounds, which help in scavenging undesired radicals and favoring slowness in electron and hole recombination.
The degradation of pollutants undergoes five major steps. In steps 1 and 2, pollutant molecules are transferred to the surface of the photocatalyst and followed by adsorption onto the active sites. In step 3, once the pollutants get attached to the active sites, the electrons get photoexcited and initiate the photocatalytic degradation process. In steps 4 and 5, once the pollutant is degraded, desorption occurs, and finally, the degraded molecules are released to the water surface (Wang et al. 2015; Gopinath et al. 2020). Additionally, the process of degradation leads to the possible formation of five different products. The process of photocatalytic degradation and end products depends upon the type of pollutant and photocatalyst choice. The possible products that can be resulted at the end of the photocatalytic process are dehalogenated compounds, oxides of alkali, isomerized and cyclized compounds, aromatic ring molecules and decarboxylated compounds (Prihod’ko and Soboleva 2013).
Techniques for titanium dioxide synthesis
Works of literature have shown that the synthesis of titanium dioxide (TiO2) could be achieved through various methodologies including chemical, physical and green (Nabi et al. 2020a; Sharma et al. 2020; Wang et al. 2020b). Table 1 provides a detailed literature comparison on the synthesis routes of titanium dioxide-based catalysts for environmental applications. A variety of different techniques including vapour deposition (Singh et al. 2019a), electrodeposition (He et al. 2019), sol–gel method (Phattepur et al. 2019), hydrothermal method (Wang et al. 2020b), solvothermal method (Ramakrishnan et al. 2018), microwave method (Cabello et al. 2017) and sonochemical method (Moreira et al. 2020) has been extensively used in the past few years to produce nano- titanium dioxide. Though chemical synthesis of titanium dioxide nanoparticles has widely been used owing to the ease of synthesis and effective control of size and shape of nanoparticles, there still exist certain limitations including high cost, the requirement of extreme temperatures and pressures, and eco-toxicity. Consequently, these disadvantages limit titanium dioxide applications in different fields and their mass industrial production (Nadeem et al. 2018). Therefore, there has been a paradigm shift in recent times towards a more eco-friendlier way of titanium dioxide fabrication called the “green synthesis,” wherein reducing agents derived from biological extracts are used for synthesis (Edmundson et al. 2014; Subhapriya and Gomathipriya 2018). The upcoming subsection of the review paper covers a few of these most used techniques for titanium dioxide synthesis in detail.
Physical and chemical methods
Sol–gel technique
Sol–gel is a very versatile wet-chemical technique that has been extensively used in ceramic and material sciences engineering fields. The process proceeds through the conversion of a precursor mixture into an inorganic solid (usually inorganic metal salts or metal alkoxides) via polymerization reactions initiated by water (Nyamukamba et al. 2018). The hydrolysis step leads to the formation of a sol (aggregate of colloidal particles dispersed in a fluid) while the condensation reaction forms a gel. As mentioned earlier, the most common precursors for sol–gel are metal chlorides and metal alkoxides. The metal alkoxides are made up of an M–O–R linkage, where M stands for the metal, O stands for oxygen and R stands for an alkyl group. The incidence of a polarization reaction in the M–O bond makes the whole molecule susceptible to a nucleophilic substitution and in the presence of water molecules; the alkoxide group are substituted and replaced by hydroxyl ions from water (hydrolysis). Following this, the produced metal hydroxides inter-molecularly connect and generate a hydrated metal oxide network eventually forming small crystal nuclei (condensation) and this is how a typical sol–gel process occurs.
Among the various physical/chemical techniques, sol–gel is a very promising one since it allows the operation of the whole synthesis under low temperatures i.e. < 100 °C and provides a molecular level homogeneity in products (Malekshahi Byranvand et al. 2013). The other benefits of the sol–gel technique include easy monitoring and control of nanoparticle shape and size. Being a flexible technique, sol–gel process could be employed to produce a variety of products like spherical, fine and uniform-sized nanopowders. Works of literature show that sol–gel has been widely used for titanium dioxide synthesis from titanium (IV) alkoxides through acid catalysis. For example, in a study mesoporous titanium dioxide nanoparticles utilizing titanium (IV) isopropoxide using surfactant-mediated sol–gel were synthesized using the water technique (Nateq and Ceccato 2019). One of the outstanding features of the sol–gel technique is the possibility to shape the product into any desired form such as a film, a fibre or even a monodispersed powder. Mehrotra and Singh comprehensively studied and established the conditions and steps applied to achieve various morphological products from the process (Mehrotra and Singh 1997), as shown in Fig. 2.
Sonochemical and microwave-assisted techniques
Ultrasound has been extensively used in the production of a wide range of nanosized materials in the past. The chemical effects arising from ultrasound do not result from direct interaction with the molecular species but instead from acoustic cavitation which involves the formation, growth and collapse of the bubbles within a liquid medium resulting in the creation of localized high pressures (~ 1000 atm) and high temperatures (~ 5000 K) (Chen 2009). The sonochemical technique has been employed to synthesize photoactive titanium dioxide nanoparticles through the hydrolysis of titanium tetraisopropoxide either in pure water or in a water/ethanol mixture using ultrasonic waves (Moreira et al. 2020).
Similar to sonochemical that employs ultrasound, the microwave-assisted technique uses microwaves (electromagnetic waves) with frequencies of 0.3–300 GHz and with wavelengths of 0.001–1 m to synthesize nano-titanium dioxide. It has been reported in a study that microwave heating involves two different mechanisms, namely ionic conduction and dipolar polarization (Zhu and Chen 2014). Any substance that contains a mobile electric charge, i.e. conducting ions or polar molecules, can be heated using microwaves. For polar molecules, the heating phenomenon occurs through the friction, rotation and collisions in between these molecules, which try to orient themselves to the rapidly alternating electric field, while for the conducting ions, the heat gets generated when these ions constantly move through the solution trying to orientate themselves with the electric field causing a local temperature rise as a result of friction and collision (Collins 2010). Microwaves have been applied to synthesize different titanium dioxide nanomaterials, especially in industrial processing due to their benefits of rapid heat transfer and selective heating (Nyamukamba et al. 2018). Cabello et al. (2017) synthesized nano-TiO2 particles with an average particle size of 73 nm and a pore diameter of 2.6 nm using microwaves under the conditions of 240 °C, 25 bar for 20 s indicating a low sintering time, thereby reducing the overall costs and energy requirements.
Oxidation techniques
The underlying principle behind these techniques is the oxidation of titanium metal to titanium dioxide either using oxidants or by anodization. Research has shown that crystalline titanium dioxide nanorods could be produced through the direct oxidation of titanium metal plates using hydrogen peroxide (Wu et al. 2005; Kumar and Pandey 2018). Archetypally, titanium dioxide nanorods could be obtained from a titanium plate when a pre-treated titanium plate is dissolved in the beaker containing 50 mL of 30 wt% hydrogen peroxide solution at 80 °C for 3 days. The formation of crystalline titanium dioxide initiates with the dissolution precipitation mechanism, followed by the addition of inorganic sodium salts (NaX; X = fluoride, sulphate, chloride ions) to control the crystalline phase of titanium dioxide nanorods. The addition of F− and SO4− forms of Na salt favours the formation of anatase while the addition of Cl− promotes the formation of rutile (Wu 2004). Apart from hydrogen peroxide pure oxygen, acetone and a mixture of argon and oxygen can alternatively be used as a source of oxygen for the oxidation of titanium (Chen and Mao 2007).
On the other hand, the anodization of titanium plate under voltages in the range of 5–20 V in a 0.5 wt% hydrogen fluoride solution leads to the production of titanium dioxide nanotubes, whose diameter could be controlled by varying the voltage applied (Chen 2009). In a recent study, Mohan et al. (2020) investigated the effects of anodization time and temperature on the formation of titanium dioxide nanotubes for biomedical purposes. The authors used titanium alloys in an electrolytic mixture of 50 mL of 1 M sulphuric acid and 50 mL of 0.08 M hydrogen fluoride at different temperatures ranging from 5 to 70 °C to prepare self-organized titanium dioxide nanotubes. They observed significant outcomes at 25 °C with titanium dioxide nanotube characteristics of 30 nm wall thickness, 250 nm length, 125 nm inner pore diameter and 35 nm inner tube space without any visible defects in their morphology unlike at other temperatures.
Deposition techniques
Deposition techniques are commonly utilized to form coatings, thereby altering the thermal, electrical, optical and mechanical properties of substrate materials. The characteristics of the product are fabricated by altering parameters like the geometry of the deposition chamber, composition, flow rate, temperature and pressure of deposition (Malekshahi Byranvand et al. 2013). Among the various deposition techniques, electrophoretic deposition and spray pyrolysis are the most favoured and employed techniques for nano-titanium dioxide synthesis (Irshad et al. 2021).
The electrophoretic deposition includes an electrolytic cell setup wherein charged particles from a suspension medium are deposited onto a substrate under the influence of the applied direct voltage (Cabanas-Polo and Boccaccini 2016) as shown in Fig. 3. When a direct voltage current is applied to the electrodes an electric field gets generated inside the cell, this field interacts with the surface charge of titanium dioxide, thereby creating a force that pulls these particles towards the electrode of opposite charge. Consequently, the accumulation of titanium dioxide onto the substrate (electrode) leads to the formation of a homogenous layer. The thickness of the layer could be adjusted by controlling the deposition parameters like deposition time, applied current/voltage, solvent type and suspension loading (Narayan and Raturi 2012). Researchers have employed various combinations of titanium dioxide thin film deposits for real-time applications like dye-sensitized solar cells (Xue et al. 2012), biomedical applications (Narkevica et al. 2017) and ceramic coatings (Ledwig et al. 2017). Nyongesa and Aduda (2017) employed electrophoretic deposition to deposit thin films of titanium dioxide onto glass substrates for application in water treatment. The authors concluded that ethanol was a better solvent to use for electrophoretic deposition compared to water, propanol and toluene, which was due to the high dielectric constant of ethanol (24.3). In general, water cannot be used as a suitable suspension medium due to the occurrence of water electrolysis, which leads to the accumulation of bubbles on electrode surfaces. The optimal parameters for the best adherence of titanium dioxide particles in the study were a pH of 3, an applied voltage of 20 V and solid loading of 4.0 wt% (Nyongesa and Aduda 2017). In a similar work performed by Nguu et al. (2018), the optimal time and voltage for achieving a uniform 5-μm titanium dioxide film were found to be 90 s and 35 V, respectively. The authors also discovered that a prolonged time > 90 s showed the agglomeration of the particles. On the contrary, Dhiflaoui et al. (2016) observed that titanium dioxide coatings on stainless steel substrates were the most homogenous at a voltage of 20 V and after a deposition time of 4 min.
While electrophoretic deposition solely allows the production of titanium dioxide films, the spray pyrolysis technique enables the fabrication of a variety of product forms including dense and fine dispersive powders (spray pyrolysis synthesis) and films (spray pyrolysis deposition). Schematic representations of different spray pyrolysis systems are presented in Fig. 4. The technique involves the spraying of a precursor’s solution across a direct flame source. This can be done in two ways: (i) by using supplemental burners mounted adjacent to the spray nozzle or (ii) by additional feeding of oxidants (i.e. air, oxygen) and the combustibles to the nozzle (Nyamukamba et al. 2018). The diameter of the spray droplets depends on the viscosity and surface tension of the precursor solution, the diameter of the nozzle tip, and the pressure difference before and after spraying (Kozhukharov and Tchaoushev 2013). The authors displayed the synthesis of ultrafine dispersive titanium dioxide powders through a swift rise in temperature inside the chamber, and during the process, the pre-formed solid particles were observed to undergo further splitting as a result of phase transitions and mechanical tensions (Kozhukharov and Tchaoushev 2011). The spray pyrolysis deposition has been reported to be performed both using a hot spray and a cold spray on a pre-heated substrate. For instance, Möllmann et al. (2019) prepared compact titanium dioxide layers using cold spray pyrolysis on a glass substrate preheated to 450 °C for the application in perovskite solar cells. The authors attempted to carry out the deposition process using substrates at low temperatures of 150 °C to reduce the overall cost of the process but observed the formation of a cracked titanium dioxide layer, which exhibited low light transmittance and reduced the device’s efficiency (Möllmann et al. 2019).
Hydro- and solvothermal techniques
Both these techniques hydrothermal and solvothermal are almost similar. In the hydrothermal technique, the substance is crystallized at high temperatures and vapour pressures using an aqueous suspension of the material (Reis et al. 2002). In general, this technique could be considered as crystal growth or crystal synthesis from materials that are commonly insoluble at customary pressure, i.e. < 1 atm, and temperature, i.e. 100 °C. This process is usually carried out in autoclaves under a controlled atmosphere, which in turn enables the utilization of temperature above the boiling point of water or an organic solution inside the chamber. Briefly, hydrothermal synthesis is described as a concoction response taking place in a dissolvable mixture at temperatures above the mixture’s breaking point and pressures over the bar. Since the essential properties of water including viscosity, heat capacity, thermal conductivity, dielectric constant and ionic product density are all temperature–pressure dependent, the hydrothermal technique exploits these properties, thereby tuning the synthesis factors and achieving specific solvent attributes. However, the technique has a few drawbacks including the high capital requirement for instrumentation, the inability to monitor crystal growth and the method which can only be performed under supercritical conditions of the solvent (Liu et al. 2014). Conversely, in solvothermal techniques, non-aqueous solvents with very high boiling points could be used and this consequently enables much better control over the properties of titanium dioxide particles during the synthesis. For instance, Kathirvel et al. (2020) produced titanium dioxide nanocrystals by treating titanium (IV) isopropoxide with various alcohol solvents (ethanol, propanol, isopropyl alcohol, butanol, tert-butyl alcohol and benzyl alcohol) at 150 °C for 8 h, while Li et al. (2020) used a one-step solvothermal technique to synthesize titanium dioxide from titanocene dichloride with uniform particle size without the use of any surfactants. The solvothermal technique allows better control over the size, shape, crystallinity and distribution of titanium dioxide nanoparticles compared to the hydrothermal, and these could be achieved through effective manipulation of reaction temperature, solvent and surfactant characteristics and reaction time (Stride and Tuong 2010). Additionally, the employment of organic solvents results in a product, which is free from extraneous anions because organic solvents tend to be devoid of ionic species and have relatively low permittivity (Nyamukamba et al. 2018).
Biological methods
Owing to the toxic nature of the chemical techniques towards the environment and the limitations encountered with the mass production, the search for a more sustainable and eco-friendly approach is greatly favoured. As an alternative, the green nanotechnology has gained a lot of attention lately for the production of titanium dioxide nanoparticles from naturally occurring biological resources (i.e. plants, fruit extracts, microorganisms and their waste materials) and for its cost-effect benefits (Nadeem et al. 2018; Singh et al. 2019b).
Plants contain nutrients like carbohydrates, proteins, alkaloids and nucleic acids, which can be used during particle synthesis for stabilization and reduction reactions. Moreover utilizing plant-based extracts as the key components for titanium dioxide production provides an additional safety compared to chemical/physical techniques (Irshad et al. 2021). Nabi et al. (2020a, b) prepared spherical-shaped anatase titanium dioxide nanoparticles through green synthesis using cinnamon powder. The overall method was reported to be feasible, simple and cost-effective. The product was found to have a band gap residing in the visible light zone along with the presence of oxygen vacancies and excitons necessary for its application in solar cells. In general, green synthesis commonly involves extracts obtained from leaves of plants as raw materials for nanoparticle synthesis since this section of plants is found to have high metabolites (Subhapriya and Gomathipriya 2018). For instance, Kumar used the leaf extracts of Syzygiumcumini and synthesized spherical aggregates of titanium dioxide using an eco-friendly, cheap and non-toxic technique (Kumar 2020). The so produced titanium dioxide was employed for treating lead-contaminated industrial waters and the authors reported a maximum removal of 82.5%.
Analogous to plants, microbial extracts from bacteria and fungi have also been utilized to biologically produce nano-titanium dioxide. These microbial extracts have gained considerable attention lately due to their low capital requirement, simple extraction leading to easier scale-up and larger surface of the synthesized product (Pantidos and Horsfall 2014). Peiris et al. (2018) identified the antimicrobial properties of baker’s yeast and used them to synthesize highly pure small-sized titanium dioxide particles (anatase) via a cost-efficient green technique. In a different study, Streptomyces species were used to synthesize less toxic and cheap but highly pure titanium dioxide nanoparticles (Ağçeli et al. 2020). The authors described the method to be simple and quick for achieving antibiofilm and antimicrobial properties-based products. Likewise, various shapes and sizes of titanium dioxide nanostructures have been reported to be synthesized from fungal extracts as they can produce a range of enzymes and other metabolites that can break down large salt molecules into elemental ions (Nadeem et al. 2018). For example, a study carried out by Rajakumar et al. (2012) established the fungus Aspergillus flavus as a novel species for biological titanium dioxide production. Aside from plants and microbes, various derivatives of biological origin like albumen, starch and cellulose have also shown some potential in producing titanium dioxide (Bao et al. 2012; Muniandy et al. 2017). However, nanoparticle titanium dioxide synthesis using these bio-derivatives has not been much explored like their counterparts. A comparison between the various techniques used for the synthesis of nano-TiO2 particles is summarized in Table 2 based on the technique’s major influencing factor, merits and demerits.
Applications of titanium dioxide
Removal of metals and dyes
In recent years, much attention has been paid by the research community to the simultaneous removal of dyes as well as heavy metals (Louangsouphom et al. 2019; de Lima et al. 2020; Izzudin et al. 2021). This methodology minimizes the processing time, operating cost as well as the use of chemicals in comparison with individual treatment methods. Titanium dioxide was found to be very effective in simultaneous removal of heavy metals and dyes. In some cases, the presence of one pollutant was found to enhance the removal of another pollutant. For instance, the presence of rhodamine B dye, during the transformation of aqueous metal chromium (IV) to chromium (III) using titanium dioxide nano-fibre membrane accelerated the removal rate (Zhang et al. 2021), and under optimized conditions, the removal efficiency of chromium (IV) was found to be 97.09%.
The efficacy of hetero-layered titanium dioxide incorporated on layered double hydroxide-molybdenum disulphide nanostructure was recently tested on the removal of organic cations and ionic dyes along with silver and lead ions and found that 97–99% dye removal was achieved (Panchal et al. 2021). Simultaneously, due to its excellent affinity and selectivity for heavy metal ions, it rapidly reduced the toxic lead from 10 mg/L to less than 0.8 µg/L and this substrate showed an enormous adsorption capacity of silver (421.88 mg/g). In recent years, different forms of nano-titanium dioxide were used which include one-dimensional nanowire, a nanobelt, two-dimensional nanotubes and nanosheets and three-dimensional nanoparticles as well as nanorods. The major advantages of one-dimensional nanobelt are lesser number of grain boundaries, fast charge transfer dynamics and high specific surface, which makes nanobelt more attractive (Pang et al. 2015).
The major disadvantages of one-dimensional nanobelt are (1) higher recombination rate of photoinduced electron–hole pairs due to the single-phase structure, and (2) pure titanium dioxide can only absorb ultraviolet irradiation because of its high band gap, which prevents this nanobelt from widespread applications (Tian et al. 2015). But these issues were resolved by researchers in recent years. For instance, less recombination of electron/hole pairs was observed during the use of novel hybrid bismuth subcarbonate (Bi2O2CO3) quantum dot/titanium dioxide nanobelt on the removal of rhodamine blue (Wang et al. 2021b). The removal efficiency of 95.43% under visible light, which is nine times larger than that of titanium dioxide nanobelts, was observed.
Literature related to the simultaneous removal of heavy metals and dyes is listed in Table 3. A mesoporous 2D-2D TiO2(B)-bismuth oxobromide heterojunction photocatalyst was synthesized and used for the degradation of mixed pollutants such as rhodamine blue, methyl orange, tetracycline hydrochloride and bisphenol A (Han et al. 2021). This substrate produced abundant superoxide radicals under visible light, which enabled the catalyst to accelerate the degradation process well. The removal of rhodamine blue, methyl orange tetracycline hydrochloride and bisphenol A using this synthesized substrate was found to be 4.7, 1.4, 23 and 16.4 times higher than that of using pure bismuth oxobromide, respectively. Recently, Karpuraranjith et al. (2022) synthesized a novel three-dimensional hybrid photocatalyst by embedding a porous molybdenum disulphide nano-box on graphitic carbon nitride nanosheets containing titanium dioxide nanoparticles. Around 97.5% photocatalytic removal of methylene blue dye was achieved using this hybrid photocatalyst, in the presence of visible light. Similarly, nanoflowers were widely employed in dye degradation and reported in recent studies (Huda et al. 2019; Shang et al. 2020; Wang et al. 2020a; Quyen et al. 2021) due to their high specific surface area, well-developed pore structure, enormous photocatalytic activity (Wu et al. 2014).
On the other hand, the photocatalytic efficacy of titanium dioxide was employed with a wide range of metal/metal oxides such as silver, cadmium, chromium, copper, manganese and nickel in the degradation of rhodamine blue (Le et al. 2021; Sengul and Asmatulu 2020). It was found that among these metal/metal oxides studied, silver- titanium dioxide produced maximum removal of 98.4% after 60 min, which follows second-order kinetics. All other metal/metal oxides coupled with titanium dioxide followed pseudo-first-order kinetics. Figure 5 provides the mechanistic pathway of dye degradation pathway with titanium dioxide as photocatalyst. A multi-metal oxide including catalyst (titanium dioxide–cadmium oxide-zinc oxide) loaded on silver nanoparticles in the presence of reduced graphene oxide was synthesized, and its photocatalytic efficacy on methylene blue degradation (Akyüz 2021) was explored and found 91% degradation within 15 min under ultraviolet irradiation, mainly attributed to decrease in the wide band gap of titanium dioxide due to the presence of multi-transition oxides. Similar strategy was used to degrade azo dye reactive violet 5 dye by titanium dioxide nanoparticles (Chung and Chen 2009).
Removal of microplastics
In our day-to-day life, plastics took an exceptional place due to their less weight, cheapness, versatility and high durability (Morin-Crini et al. 2022; Alqahtani and Zafar 2021). On the other hand, disposal of used plastics is a big challenge as only just 14% of used plastics are recycled while others enter into our environment in one way or another. More than 8 million metric tons of used plastics are entering into water bodies, every year (MacArthur 2017). Accumulation of these plastics in seas and oceans would surpass the amount of fish present in oceans in near future. These used plastics were decomposed due to physical degradation in the presence of sunlight, micro-organisms into micro-plastics (size less than 5 μm) and nano-plastics (size less than 1 μm) (Koelmans et al. 2015). Degradation of micro-plastics using conventional wastewater purification methodologies has difficulties in control and complete elimination (Moore 2008). TiO2 has been used widely in recent years to degrade these micro-plastics. The widely found micro-plastics such as polyethene and polystyrene can be completely degraded using Triton-based titanium dioxide nanoparticle films and ultraviolet light, through photocatalytic mineralization (Nabi et al. 2020b).
Wang et al. (2019) prepared a novel magnetic Au@Ni@TiO2 micromotor, by applying 10 nm thickness of nickel layer on titanium dioxide particles, covered with a 30-nm layer of gold, for the removal of microplastics present in water and hydrogen peroxide under ultraviolet light. This motor was found to have a velocity of 14.72 and 65.52 μm S−1 in water and 0.1% hydrogen peroxide solution, respectively. They showcased the efficacy of this micromotor on the degradation of microplastics from personal care products as well as river water and reported 67% of clearage efficiency in pure water. A faster elimination can be achieved by adding a low percentage of hydrogen peroxide to pure water.
The use of ultraviolet light, as well as hydrogen peroxide, makes this fuel-free micromotor less attractive. Some research works to overcome this issue were performed by researchers. The recent works dealing with titanium dioxide-based Janus micromotors are listed in Table 4. Recently, Janus cobalt oxide–titanium dioxide micro-swimmers driven by low intensity–ultraviolet free visible light present inside water were prepared and tested (Sridhar et al. 2020). These micro-swimmers propel by breaking down the water molecules into oxygen and oxide radicals, which enabled them to be applicable in photocatalytic reactions as well as drug delivery. The mean velocity of this micro-swimmer was found to be 11.5 μm S−1 at the intensity of 6 mW cm−2. It can also be accelerated under a magnetic field due to the presence of cobalt oxide.
Electrocatalysis for energy
Currently, heteroatom doping technology has emerged as an intriguing technique to enhance electrocatalytic efficiency (Ochedi et al. 2021; Kumar et al. 2021). An inexpensive and novel catalyst without using noble metals, namely carbon, nitrogen–zeolitic imidazolate framework/TiFe (that is carbon and nitrogen derived from zeolitic imidazolate framework-8 embedded in titanium dioxide/ferric oxide) was found to exhibit superior electrocatalytic performance towards water splitting, oxygen evolution reactions and hydrogen evolution reactions (Vattikuti et al. 2021). This synthesized catalyst has more excellent catalytic power than that of zeolitic imidazolate framework/TiFe and TiFe nanostructures, towards oxygen evolution reactions and hydrogen evolution reactions. The overpotential was found to be 290 mV and 291 mV for oxygen evolution reactions and hydrogen evolution reactions, respectively, to deliver the benchmark current density of 10 mA cm−2 under alkaline conditions. This was attributed to the addition of highly active carbon and nitrogen from zeolitic imidazolate framework with titanium dioxide/ferric oxide, which enhanced the rate of water splitting.
Similarly, numerous researchers made innovations in making novel catalysts to enhance the electrocatalytic processes and some of these novel catalysts recently reported are listed in Table 5. Another novel catalyst using reduced titanium dioxide-supported ruthenium nanocatalyst was developed with more oxygen vacancies for hydrogen evolution (Chen et al. 2021b). This nanocatalyst required very less overpotential (15 mV) to deliver the current density of 10 mA cm−2 under alkaline conditions. This superior performance was attributed to synergistic water splitting and weakening of OH· adsorption.
Antimicrobial activity
In recent years, the spreading of infectious diseases such as Ebola, and severe acute respiratory syndrome coronavirus 2 (SARS), is very rapid (COVID-19 in particular) and the health department across the world is working hard to contain these diseases. So, it is highly needed to disinfect the high touch surfaces, such as sinks, faucets, handrails, doorknobs and in public places, as these are acknowledged as a pool of agents causing a wide range of infections (Huslage et al. 2010). Numerous antibacterial/antiviral chemicals were used to sanitize these high touch surfaces, which needs more manpower and chemical use. Thus, the use of self-disinfecting materials on these surfaces is one of the best options to prevent the spreading of COVID-19 and other infectious diseases (Mathew et al. 2020). Many studies made in this decade elucidated the antibacterial efficacy of photocatalysts (Mahmood et al. 2012; Lin et al. 2013; McEvoy and Zhang 2014). These photocatalyst-based substrates gained more attention from the research community due to the direct utilization of sunlight or in some cases, ultraviolet irradiation. Among the photocatalysts employed, TiO2 is the most extensively used photocatalyst for antimicrobial applications (Foster et al. 2011; Yousef et al. 2015; Mathew et al. 2018).
Very recently, the effective use of titanium dioxide on disinfecting the SARS-CoV-2 virion (severe acute respiratory syndrome coronavirus 2) present in the air, as well as the liquid, was tested (Matsuura et al. 2021). The study elucidated the efficacy of titanium dioxide-mediated photocatalytic reaction on this virion that about 99% reduction in infectivity in aerosol after 20 min of treatment while it took 120 min for achieving this level in liquids. This disinfection happened due to the damage caused to the viral proteins and the genome through the mechanistic effects of titanium dioxide. Similarly, the research community performed numerous innovative works since 2020 to contain the covid-19 pandemic across the world and some of these works using titanium dioxide-based substrates are listed in Table 6.
A significant enhancement in the antibacterial property of titanium dioxide was observed with the addition of chalcogens such as sulphur, selenium and tellurium (Mathew et al. 2020). Among these three chalcogens, tellurium-doped titanium dioxide stood first on antimicrobial behaviour against E. coli as complete disinfection was achieved within 70 min of light irradiation while the other two chalcogens when doped with titanium dioxide produced little less activity (took 90 min for complete disinfection).
Similarly, cerium-doped titanium dioxide nanoparticles deposited on reduced graphene oxide were found to enhance the microbial activity as well as photocatalytic behaviour under visible light (Behera et al. 2021). This is attributed to the fact that the presence of cerium increases the absorption of titanium from ultraviolet to visible light. This novel substrate containing cerium was found to be more effective, under visible light, in disinfecting human pathogenic bacteria as well as degradation of two pesticides, namely quinalphos and imidacloprid, in comparison with the conventional titanium dioxide catalyst.
The use of zinc oxide, titanium dioxide and silicon dioxide-based nanomaterials on creating protective coatings against biodeterioration was getting momentum in recent years. In another study, titanium dioxide induces membrane rupture (Ranjan and Ramalingam 2016). Therefore, there is a need to compare the efficacy of these substates on antimicrobial activity. In a recent study, these nanomaterials were tested and compared against eight different types of micro-organisms that are commonly found on building material surfaces such as Bacillus subtilis, Aspergillus niger, Aspergillus terreus, Aureobasidium pullulans, Cladosporium cladosporioides, Penicillium ochrochloron, Trichoderma viride, Paecilomyces variotii (Dyshlyuk et al. 2020). Among these three nanomaterials studied, zinc oxide with particle sizes 2–7 mm was found to be most efficient against these micro-organisms.
Nanomedicine
Nanoparticle-based drugs have been introduced in recent years to increase the efficiency of treatment strategies in oncology in treating cancer cells (Umapathi et al. 2021; Patel et al. 2021; Sharma et al. 2017). In a recent study, the autophagic potential of titanium dioxide nanoparticles was explored in increasing the chemotherapeutic effect of 5-fluorouracil in human AGS gastric cells (human gastric adenocarcinoma cell line) (Azimee et al. 2020). The production of reactive oxygen species by titanium dioxide impaired the lysosomal function, which leads to a block in autophagy flux in AGS cells. A microlevel addition (1 μg/ml) of these titanium dioxide nanoparticles enhanced the cytotoxic as well as apoptotic effects of 5-fluorouracil.
A case study was performed by a team of researchers on the treatment of diabetic foot ulcers using catalytic nanomedicine containing copper/titanium dioxide–silicon dioxide as it was estimated that around 20% of diabetic patients will develop foot ulcers over their lifetime (López-Goerne et al. 2019). These works observed a significant improvement healing process on the first application itself, and the infection was limited. Further, the regeneration of tissue was enhanced due to its use.
In dentistry, the research community is in search of an efficient method to reduce bacterial adhesion on archwires and around the orthodontic appliance to restrict enamel decalcification as well as periodontal diseases. In this area, one study was performed to clinically test the efficacy of titanium dioxide nanostructure coating on stainless steel orthodontic wires towards the growth of most found bacteria in dentistry, namely Streptococcus mutans (Mollabashi et al. 2020). It was found that decreased adhesion of S. mutans was found on tested orthodontic wires which is attributed to the fact that, the damage in the cell wall of this micro-organism due to titanium dioxide leads to changes in osmotic pressure; subsequently, the cell organelles were destroyed. However, further studies are needed in this area to investigate the mechanical stability of titanium dioxide-coated stainless steel orthodontic wires under mechanical loading during the dental treatment.
Removal of pharmaceutical and personal care products
Pharmaceuticals and personal care products (PPCPs) are substances that are man-made for human and/or animal healthcare and medical purposes (Jiang et al. 2013; Omar et al. 2016; Yang et al. 2017). These substances can be classified into a different wide range of products such as antibiotics, antifungal, antiemetics, antineoplastics, vaccinations, contrast agents, sedatives, anticonvulsants, nonsteroidal anti-inflammatory drugs, hormones, lipid regulators, painkillers, b-blockers, preservatives, disinfectants, insect repellents, fungicides, soaps and detergents, fragrances, sunscreen ultraviolet filters (Yang et al. 2017). More than 3000 pharmaceuticals and personal care products have been produced as of now (Šauer et al. 2019; Chen et al. 2016) and the constant development of new chemical compounds to contain different newly arising diseases such as COVID-19, Ebola, severe acute respiratory syndrome, led to an increasing abundance and variety of pharmaceuticals and personal care products in the environment. Several methodologies were implemented to reduce the load caused by pharmaceuticals and personal care products, and some of the titanium dioxide-based methodologies proposed in recent studies are listed in Table 7 (Saravanan et al. 2020; Ajiboye et al. 2021; He et al. 2021).
Oil recovery
Many oilfields are employing alkali/surfactant/polymer to enhance the oil recovery across the world, which produces much better results than water flooding. Production of highly stable emulsion (which contains residual oil in the water phase) leads to a decrease in the efficacy of the recovery process. The presence of titanium dioxide was found to enhance the oil recovery due to many reasons. (1) Titanium dioxide is intrinsically hydrophilic (Choi et al. 2017; Kameya and Yabe 2019), the attraction of water molecules increased the water layer and thereby the residual emulsion decreased; (2) improved coalescence between adjacent oil droplets; and (3) improved behaviour of oil/water interfacial film (Kang et al. 2012). Khan et al. (2021) observed 75% clarity in the separated aqueous phase in the presence of titanium dioxide while it was 45% without titanium dioxide, which leads to a 19% overall increase in oil/water separation due to the presence of titanium dioxide.
A newly developed titanium dioxide/silicon dioxide/poly(acrylamide) nanocomposites using pomegranate seeds has shown better results in the enhanced oil recovery process in carbonate reservoirs (Ali et al. 2021). These nanocomposites (1500 ppm) when mixed with smart nanofluid (5000 ppm of calcium sulphate and calcium chloride ions) demonstrated the highest performance in oil recovery from 36% to 46.53% original oil in place due to a reduction in interfacial tension and wettability alteration.
In addition to enhanced oil recovery, research broadened the application of titanium dioxide in different areas such as (1) it can also be used as an excellent insulator which leads to better energy saving in the oil recovery process; (2) it can be used in the purification of recovered oily organic substances from waste liquids or accidental oil discharges in marine or continental situations.
The titanium dioxide–silicon dioxide composite was found to have excellent infrared radiation shield capability, and thus the composite can be used as a thermal insulator for high-temperature steam pipes used in oil recovery. This glass fibre/titanium dioxide–silicon dioxide composite significantly reduces the thermal conductivity by 13.1% and 23.9% at 300 °C and 400 °C, respectively (Liu et al. 2021).
Recently, super-hydrophobic F-TiO2@polypropylene membranes were prepared from polypropylene, trifluorofluorooctyl methacrylate and sol–gel-derived titanium dioxide with vinyltriethoxysilane by Zhu et al. (2021) to recover oily organic components from waste liquids. This membrane was found to enhance the water contact angle up to 157°, and thus, the water removing efficiency was found to be more than 99.7%.
Degradation of pesticides
The residues of pesticides even at minute levels can cause severe harmful effects on human and animal health (Sakkas et al. 2005; Bamba et al. 2008; Colombo et al. 2012; Kaur and Goyal 2019), and the condition still worsens with bioaccumulation of these pesticides in long run (Garcia et al. 2006; Bamba et al. 2008). Many studies (Kaur and Goyal 2019) were performed in recent years to degrade this pesticide, and some recent work is listed in Table 8.
Conclusion
Photocatalysis with titanium dioxide (TiO2) is highly recommended for effective wastewater treatment as this technique removes pollutants to a greater extent than conventional physical techniques such as adsorption and coagulation. Titanium dioxide nano-catalysts are commonly synthesized by physiochemical, e.g. solgel technique, sonochemical and microwave-assisted technique, oxidation technique, deposition technique, hydro/solvothermal techniques, and biological methods. Physical characteristics of titanium dioxide nanoparticles are strongly dependent on the synthesis technique adopted.
Abbreviations
- BTEX:
-
Benzene toluene ethylbenzene and xylene
- SARS:
-
Severe acute respiratory syndrome
- PPCP:
-
Pharmaceutical and personal care products
References
Abeledo-Lameiro MJ, Ares-Mazás E, Gómez-Couso H (2016) Evaluation of solar photocatalysis using TiO2 slurry in the inactivation of Cryptosporidium parvum oocysts in water. J Photochem Photobiol B Biol 163:92–99
Aftab U, Tahira A, Gradone A et al (2021) Two step synthesis of TiO2–Co3O4 composite for efficient oxygen evolution reaction. Int J Hydrogen Energy 46:9110–9122
Ağçeli G, Hammachi H, Kodal S et al (2020) A novel approach to synthesize TiO2 nanoparticles: Biosynthesis by using Streptomyces sp. HC1. J Inorg Organomet Polym Mater 30:3221–3229. https://doi.org/10.1007/S10904-020-01486-W
Ajiboye TO, Oyewo OA, Onwudiwe DC (2021) Photocatalytic removal of parabens and halogenated products in wastewater: a review. Environ Chem Lett 1–31
Akyüz D (2021) rGO-TiO2-CdO-ZnO-Ag photocatalyst for enhancing photocatalytic degradation of methylene blue. Opt Mater (amst) 116:111090
Ali JA, Kolo K, Manshad AK, Stephen KD (2021) Emerging applications of TiO2/SiO2/poly (acrylamide) nanocomposites within the engineered water EOR in carbonate reservoirs. J Mol Liq 322:114943
Alqahtani FK, Zafar I (2021) Plastic-based sustainable synthetic aggregate in Green Lightweight concrete—a review. Constr Build Mater 292:123321. https://doi.org/10.1016/J.Conbuildmat.2021.123321
Ao CH, Lee SC, Yu JZ, Xu JH (2004) Photodegradation of formaldehyde by photocatalyst TiO2: effects on the presences of NO, SO2 and VOCs. Appl Catal B Environ 54:41–50. https://doi.org/10.1016/J.apcatB.2004.06.004
Arconada N, Durán A, Suárez S et al (2009) Synthesis and photocatalytic properties of dense and porous TiO2-anatase thin films prepared by sol–gel. Appl Catal B Environ 86:1–7. https://doi.org/10.1016/J.apcatB.2008.07.021
Azimee S, Rahmati M, Fahimi H, Moosavi MA (2020) TiO2 nanoparticles enhance the chemotherapeutic effects of 5-fluorouracil in human AGS gastric cancer cells via autophagy blockade. Life Sci 248:117466
Bamba D, Atheba P, Robert D et al (2008) Photocatalytic degradation of the diuron pesticide. Environ Chem Lett 6:163–167. https://doi.org/10.1007/S10311-007-0118-X/TABLES/2
Bao S, Lei C, Xu M et al (2012) Environment-friendly biomimetic synthesis of TiO2 nanomaterials for photocatalytic application. Nanotechnology. https://doi.org/10.1088/0957-4484/23/20/205601
Barahimi V, Taheri RA, Mazaheri A, Moghimi H (2020) Fabrication of a novel antifouling TiO2/CPTES/metformin-PES nanocomposite membrane for removal of various organic pollutants and heavy metal ions from wastewater. Chem Pap 74:3545–3556
Behera L, Barik B, Mohapatra S (2021) Improved photodegradation and antimicrobial activity of hydrothermally synthesized 0.2 Ce-TiO2/RGO under visible light. Colloids Surfaces A Physicochem Eng Asp 620:1265
Bhattacharya P, Mukherjee D, Deb N et al (2021) Indigenously developed CuO/TiO2 coated ceramic ultrafiltration membrane for removal of emerging contaminants like phthalates and parabens: toxicity evaluation in PA-1 cell line. Mater Chem Phys 258:123920
Bhuvaneswari R, Jeyanthi J, Kumar M (2021) Visible light assisted degradation of atenolol by Fe-TiO2: synthesis, characterization, optimization and mechanism. Optik (stuttg) 239:166658
Boruah PK, Das MR (2020) Dual responsive magnetic Fe3O4-TiO2/graphene nanocomposite as an artificial nanozyme for the colorimetric detection and photodegradation of pesticide in an aqueous medium. J Hazard Mater 385:121516
Boutillier S, Fourmentin S, Laperche B (2021) History of titanium dioxide regulation as a food additive: a review. Environ Chem Lett 1–17
Cabanas-Polo S, Boccaccini AR (2016) Electrophoretic deposition of nanoscale TiO2: technology and applications. J Eur Ceram Soc 2:265–283. https://doi.org/10.1016/J.Jeurceramsoc.2015.05.030
Cabello G, Davoglio RA, Pereira EC (2017) Microwave-assisted synthesis of anatase-TiO2 nanoparticles with catalytic activity in oxygen reduction. J Electroanal Chem 794:36–42. https://doi.org/10.1016/J.Jelechem.2017.04.004
Camarillo R, Tostón S, Martínez F et al (2017) Enhancing the photocatalytic reduction of CO2 through engineering of catalysts with high pressure technology: Pd/TiO2 photocatalysts. J Supercrit Fluids 123:18–27. https://doi.org/10.1016/J.Supflu.2016.12.010
Chava RK, Lee W-M, Oh S-Y et al (2017) Improvement in light harvesting and device performance of dye sensitized solar cells using electrophoretic deposited hollow TiO2 NPs scattering layer. Sol Energy Mater Sol Cells 161:255–262
Chen X (2009) Titanium dioxide nanomaterials and their energy applications. Chin J Catal 30:839–851. https://doi.org/10.1016/S1872-2067(08)60126-6
Chen X, Mao SS (2007) Titanium dioxide nanomaterials: synthesis, properties, modifications, and applications. Chem Rev 107:2891–2959. https://doi.org/10.1021/CR0500535
Chen Y, Vymazal J, Březinová T et al (2016) Occurrence, removal and environmental risk assessment of pharmaceuticals and personal care products in rural wastewater treatment wetlands. Sci Total Environ 566:1660–1669
Chen J, Wang M, Han J, Guo R (2020) TiO2 nanosheet/NiO nanorod hierarchical nanostructures: p–n heterojunctions towards efficient photocatalysis. J Colloid Interface Sci 562:313–321. https://doi.org/10.1016/J.JCIS.2019.12.031
Chen B, Liu L, Liu K et al (2021a) Photoelectrochemical TiO2-Au-nanowire-based motor for precise modulation of single-neuron activities. Adv Funct Mater 31:2008667. https://doi.org/10.1002/ADFM.202008667
Chen LN, Wang SH, Zhang PY et al (2021b) Ru nanoparticles supported on partially reduced TiO2 as highly efficient catalyst for hydrogen evolution. Nano Energy 88:106211. https://doi.org/10.1016/J.NANOEN.2021.106211
Choi SK, Son HA, Kim HT, Kim JW (2017) Nanofluid enhanced oil recovery using hydrophobically associative zwitterionic polymer-coated silica nanoparticles. Energy Fuels 31:7777–7782
Chung Y-C, Chen C-Y (2009) Degradation of azo dye reactive violet 5 by TiO2 photocatalysis. Environ Chem Lett 7:347–352
Collins M (2010) Future trends in microwave synthesis. Future Med Chem 2:151–155. https://doi.org/10.4155/FMC.09.133
Colombo A, Cappelletti G, Ardizzone S et al (2012) Bisphenol A endocrine disruptor complete degradation using TiO2 photocatalysis with ozone. Environ Chem Lett 10:55–60. https://doi.org/10.1007/S10311-011-0328-0
Daghrir R, Drogui P, Robert D (2013) Modified TiO2 for environmental photocatalytic applications: a review. Ind Eng Chem Res 52:3581–3599. https://doi.org/10.1021/IE303468T
de Freitas AM, Sirtori C, Peralta-Zamora P (2011) Photoelectrocatalytic degradation of camphor on TiO2/RuO2 electrodes. Environ Chem Lett 9:97–102. https://doi.org/10.1007/S10311-009-0252-8
de Lima BRM, do Nascimento NMP, Zamian JR et al (2020) Higher dye degradation using a visible-light photocatalyst made of mesoporous graphitic carbon nitride prepared with the Tween-40 surfactant. Environ Chem Lett 18:1413–1422. https://doi.org/10.1007/S10311-020-01008-7
Deng L, Chang B, Shi D et al (2021) MXene decorated by phosphorus-doped TiO2 for photo-enhanced electrocatalytic hydrogen evolution reaction. Renew Energy 170:858–865
Devahasdin S, Fan C, Li K, Chen DH (2003) TiO2 photocatalytic oxidation of nitric oxide: transient behavior and reaction kinetics. J Photochem Photobiol A Chem 156:161–170. https://doi.org/10.1016/S1010-6030(03)00005-4
Dhiflaoui H, Khlifi K, Cheikh larbi A (2016) Effect of deposition parameters on electrophoretically deposited TiO2. Res Rev J Mater Sci 4:7–15. https://doi.org/10.4172/2321-6212.1000148
Diao W, Xu J, Rao X, Zhang Y (2021) Facile synthesis of fluorine doped rutile TiO2 nanorod arrays for photocatalytic removal of formaldehyde. Catal Lett 2021(1):1–11. https://doi.org/10.1007/S10562-021-03700-X
Dyshlyuk L, Babich O, Ivanova S et al (2020) Antimicrobial potential of ZnO, TiO2 and SiO2 nanoparticles in protecting building materials from biodegradation. Int Biodeterior Biodegrad 146:104821
Edmundson M, Capeness M, Horsfall L (2014) Exploring the potential of metallic nanoparticles within synthetic biology. N Biotechnol 31:572–578. https://doi.org/10.1016/J.NBT.2014.03.004
EL-Saeid MH, Alotaibi M, Alshabanat M et al (2021) Impact of photolysis and TiO2 on pesticides degradation in wastewater. Water 13:655
Elbarbary AM, Gad YH (2021) Radiation synthesis and characterization of poly (vinyl alcohol)/acrylamide/TiO2/SiO2 nanocomposite for removal of metal ion and dye from wastewater. J Inorg Organomet Polym Mater 1–23
Esposito S (2019) “Traditional” sol-gel chemistry as a powerful tool for the preparation of supported metal and metal oxide catalysts. Materials (basel) 12:668
Fajardo C, Saccà ML, Costa G et al (2014) Impact of Ag and Al2O3 nanoparticles on soil organisms: in vitro and soil experiments. Sci Total Environ 473–474:254–261. https://doi.org/10.1016/J.SCITOTENV.2013.12.043
Fernández-Ibáñez P, Sichel C, Polo-López MI et al (2009) Photocatalytic disinfection of natural well water contaminated by Fusarium solani using TiO2 slurry in solar CPC photo-reactors. Catal Today 144:62–68. https://doi.org/10.1016/J.CATTOD.2009.01.039
Fiorenza R, Di Mauro A, Cantarella M et al (2020) Preferential removal of pesticides from water by molecular imprinting on TiO2 photocatalysts. Chem Eng J 379:122309
Foster HA, Ditta IB, Varghese S, Steele A (2011) Photocatalytic disinfection using titanium dioxide: spectrum and mechanism of antimicrobial activity. Appl Microbiol Biotechnol 90:1847–1868
Garcia-Muñoz P, Fresno F, Ivanez J et al (2020) Activity enhancement pathways in LaFeO3@ TiO2 heterojunction photocatalysts for visible and solar light driven degradation of myclobutanil pesticide in water. J Hazard Mater 400:123099
Garcia A, Amat AM, Arques A et al (2006) Detoxification of aqueous solutions of the pesticide “Sevnol” by solar photocatalysis. Environ Chem Lett 3:169–172
Gavrilović T V, Jovanović DJ, Dramićanin MD (2018) Synthesis of multifunctional inorganic materials: from micrometer to nanometer dimensions. In: Nanomaterials for green energy. Elsevier, pp 55–81
Ge Y, Wang T, Zheng M et al (2019) Controlled one-sided growth of Janus TiO2/MnO2 nanomotors. Nanotechnology 30:315702
Ghanbari S, Givianrad MH, Aberoomand Azar P (2019) Simultaneous reduction of Cr (VI) and degradation of azo dyes by F-Fe-codoped TiO2/SiO2 photocatalysts under visible and solar irradiation. Can J Chem 97:659–671
Gopinath KP, Madhav NV, Krishnan A et al (2020) Present applications of titanium dioxide for the photocatalytic removal of pollutants from water: a review. J Environ Manag 270:110906
Haider AJ, Al-Anbari RH, Kadhim GR, Salame CT (2017) Exploring potential environmental applications of TiO2 nanoparticles. Energy Procedia 119:332–345. https://doi.org/10.1016/J.EGYPRO.2017.07.117
Hamza RZ, Gobouri AA, Al-Yasi HM et al (2021) A new sterilization strategy using TiO2 nanotubes for production of free radicals that eliminate viruses and application of a treatment strategy to combat infections caused by emerging SARS-CoV-2 during the COVID-19 pandemic. Coatings 11:680
Han B, Tomer V, Nguyen TA et al (2020) Nanosensors for smart cities. Elsevier
Han L, Li B, Wen H et al (2021) Photocatalytic degradation of mixed pollutants in aqueous wastewater using mesoporous 2D/2D TiO2(B)-BiOBr heterojunction. J Mater Sci Technol 70:176–184. https://doi.org/10.1016/J.JMST.2020.08.036
Harris J, Silk R, Smith M et al (2020) Hierarchical TiO2 nanoflower photocatalysts with remarkable activity for aqueous methylene blue photo-oxidation. ACS Omega 5:18919–18934. https://doi.org/10.1021/ACSOMEGA.0C02142
He X, Kai T, Ding P (2021) Heterojunction photocatalysts for degradation of the tetracycline antibiotic: a review. Environ Chem Lett 19(6):4563–4601. https://doi.org/10.1007/S10311-021-01295-8
He Z, Cao D, Wang Y et al (2019) Preparation of Co–P–TiO2 nanocomposite coatings via a pulsed electrodeposition process. Surf Eng 36:975–981. https://doi.org/10.1080/02670844.2019.1693172
Hitam CNC, Jalil AA (2020) A review on exploration of Fe2O3 photocatalyst towards degradation of dyes and organic contaminants. J Environ Manag 258:110050. https://doi.org/10.1016/J.JENVMAN.2019.110050
Huda A, Suman PH, Torquato LDM et al (2019) Visible light-driven photoelectrocatalytic degradation of acid yellow 17 using Sn3O4 flower-like thin films supported on Ti substrate (Sn3O4/TiO2/Ti). J Photochem Photobiol A Chem 376:196–205
Huslage K, Rutala WA, Sickbert-Bennett E, Weber DJ (2010) A quantitative approach to defining “high-touch” surfaces in hospitals. Infect Control Hosp Epidemiol 31:850–853
Irshad MA, Nawaz R, ur Rehman MZ et al (2021) Synthesis, characterization and advanced sustainable applications of titanium dioxide nanoparticles: a review. Ecotoxicol Environ Saf 212:111978. https://doi.org/10.1016/J.ECOENV.2021.111978
Ismael M (2020) A review and recent advances in solar-to-hydrogen energy conversion based on photocatalytic water splitting over doped-TiO2 nanoparticles. Sol Energy 211:522–546. https://doi.org/10.1016/J.SOLENER.2020.09.073
Izzudin NM, Jalil AA, Aziz FFA et al (2021) Simultaneous remediation of hexavalent chromium and organic pollutants in wastewater using period 4 transition metal oxide-based photocatalysts: a review. Environ Chem Lett 1–29
Jézéquel H, Chu KH (2005) Enhanced adsorption of arsenate on titanium dioxide using Ca and Mg ions. Environ Chem Lett 3:132–135
Jiang H, He X, Ma Y et al (2021) Isotropic hedgehog shape TiO2 functional multiwall carbon nanotube micromotors with phototactic motility in fuel free environments. ACS Appl Mater Interfaces 13:5406–5417
Jiang JQ, Zhou Z, Sharma VK (2013) Occurrence, transportation, monitoring and treatment of emerging micro-pollutants in waste water—a review from global views. Microchem J 110:292–300. https://doi.org/10.1016/J.MICROC.2013.04.014
Kamal T, Anwar Y, Khan SB et al (2016) Dye adsorption and bactericidal properties of TiO2/chitosan coating layer. Carbohydr Polym 148:153–160. https://doi.org/10.1016/J.CARBPOL.2016.04.042
Kameya Y, Yabe H (2019) Optical and superhydrophilic characteristics of TiO2 coating with subwavelength surface structure consisting of spherical nanoparticle aggregates. Coatings 9:547
Kang W, Guo L, Fan H et al (2012) Flocculation, coalescence and migration of dispersed phase droplets and oil–water separation in heavy oil emulsion. J Pet Sci Eng 81:177–181
Karpuraranjith M, Chen Y, Rajaboopathi S et al (2022) Three-dimensional porous MoS2 nanobox embedded g-C3N4@ TiO2 architecture for highly efficient photocatalytic degradation of organic pollutant. J Colloid Interface Sci 605:613–623
Kathirvel S, Pedaballi S, Su C et al (2020) Morphological control of TiO2 nanocrystals by solvothermal synthesis for dye-sensitized solar cell applications. Appl Surf Sci 519:146082. https://doi.org/10.1016/J.APSUSC.2020.146082
Kaur R, Goyal D (2019) Toxicity and degradation of the insecticide monocrotophos. Environ Chem Lett 17(3):1299–1324. https://doi.org/10.1007/S10311-019-00884-Y
Kaur N, Singh M, Moumen A et al (2020) 1D Titanium dioxide: achievements in chemical sensing. Materials (basel) 13:2974
Khan MKA, Khan JA, Ullah H et al (2021) De-emulsification and gravity separation of micro-emulsion produced with enhanced oil recovery chemicals flooding. Energies 14:2249
Koelmans AA, Besseling E, Shim WJ (2015) Nanoplastics in the aquatic environment. Critical review. Mar Anthropog Litter 325–340
Kozhukharov S, Tchaoushev S (2011) Perspectives for development and industrial application of spray pyrolysis method. Annu Proceeds“angel Kanchev” Univ Ruse 50:46–50
Kozhukharov S, Tchaoushev S (2013) Spray pyrolysis equipment for various applications. Tchaoushev J Chem Technol Metall 48:111–118
Krejčíková S, Matějová L, Kočí K et al (2012) Preparation and characterization of Ag-doped crystalline titania for photocatalysis applications. Appl Catal B Environ 111–112:119–125. https://doi.org/10.1016/J.APCATB.2011.09.024
Kumar P (2020) The influence of Azadirachta indica, Melaleuca alternifolia, and Cocos nucifera on Candida albicans strain in tissue conditioner at varying time intervals. J Indian Prosthodont Soc 20:171. https://doi.org/10.4103/JIPS.JIPS_366_19
Kumar A, Pandey G (2018) Different methods used for the synthesis of TiO2 based nanomaterials: a review. Am J Nano Res Appl 6:1. https://doi.org/10.11648/J.NANO.20180601.11
Kumar PS, Venkatesh K, Gui EL et al (2018) Electrospun carbon nanofibers/TiO2-PAN hybrid membranes for effective removal of metal ions and cationic dye. Environ Nanotechnol Monit Manag 10:366–376
Kumar A, Khan M, He J, Lo IMC (2020) Visible light driven magnetically recyclable terephthalic acid functionalized g- C3N4/TiO2 heterojunction nanophotocatalyst for enhanced degradation of PPCPs. Appl Catal B Environ 270:118898
Kumar A, Shandilya P, Vo D-VN et al (2021) Metallic and bimetallic phosphides-based nanomaterials for photocatalytic hydrogen production and water detoxification: a review. Environ Chem Lett 2021(1):1–36. https://doi.org/10.1007/S10311-021-01331-7
Laxma Reddy PV, Kavitha B, Kumar Reddy PA, Kim KH (2017) TiO2-based photocatalytic disinfection of microbes in aqueous media: a review. Environ Res 154:296–303. https://doi.org/10.1016/J.ENVRES.2017.01.018
Le AT, Tan ZH, Sivakumar R, Pung SY (2021) Predicting the photocatalytic performance of metal/metal oxide coupled TiO2 particles using response surface methodology (RSM). Mater Chem Phys 269:124739. https://doi.org/10.1016/J.MATCHEMPHYS.2021.124739
Ledwig P, Kot M, Moskalewicz T, Dubiel B (2017) Electrophoretic deposition of nc-TiO2/chitosan composite coatings on X2CrNiMo17-12-2 stainless steel. Arch Metall Mater 62:405–410. https://doi.org/10.1515/AMM-2017-0063
Lee SY, Park SJ (2013) TiO2 photocatalyst for water treatment applications. J Ind Eng Chem 19:1761–1769. https://doi.org/10.1016/J.JIEC.2013.07.012
Lee GJ, Wu JJ (2017) Recent developments in ZnS photocatalysts from synthesis to photocatalytic applications—a review. Powder Technol 318:8–22. https://doi.org/10.1016/J.POWTEC.2017.05.022
Li G, Song J, Meng C et al (2020) Single source, surfactant-free, and one-step solvothermal route synthesized TiO2 microspheres for highly efficient mesoscopic perovskite solar cells. Sol RRL. https://doi.org/10.1002/SOLR.202000519
Lin W-C, Yang W-D, Huang I-L et al (2009) Hydrogen production from methanol/water photocatalytic decomposition using Pt/TiO2−xNx catalyst. Energy Fuels 23:2192–2196. https://doi.org/10.1021/EF801091P
Lin ZH, Roy P, Shih ZY et al (2013) Synthesis of anatase Se/Te-TiO2 nanorods with dominant 100 facets: photocatalytic and antibacterial activity induced by visible light. ChemPlusChem 78:302–309. https://doi.org/10.1002/CPLU.201200281
Liu N, Chen X, Zhang J, Schwank JW (2014) A review on TiO2-based nanotubes synthesized via hydrothermal method: formation mechanism, structure modification, and photocatalytic applications. Catal Today 225:34–51. https://doi.org/10.1016/J.CATTOD.2013.10.090
Liu H, Feng J, Jie W (2017) A review of noble metal (Pd, Ag, Pt, Au)–zinc oxide nanocomposites: synthesis, structures and applications. J Mater Sci Mater Electron 28(22):16585–16597. https://doi.org/10.1007/S10854-017-7612-0
Liu Z, Song Y, Wang Q et al (2019) Solvothermal fabrication and construction of highly photoelectrocatalytic TiO2 NTs/Bi2MoO6 heterojunction based on titanium mesh. J Colloid Interface Sci 556:92–101
Liu S, Wu X, Li Y et al (2021) Hydrophobic in-situ SiO2-TiO2 composite aerogel for heavy oil thermal recovery: Synthesis and high temperature performance. Appl Therm Eng 190:116745
Long C, Jiang Z, Shangguan J et al (2021) Applications of carbon dots in environmental pollution control: a review. Chem Eng J 406:126848. https://doi.org/10.1016/J.CEJ.2020.126848
López-Goerne T, Ramírez-Olivares P, Pérez-Dávalos LA et al (2019) Catalytic nanomedicine. Cu/TiO2 & SiO2 nanoparticles as treatment of diabetic foot ulcer: a case report. Curr Nanomed 10:290–295. https://doi.org/10.2174/2468187309666190906121924
López YC, Viltres H, Gupta NK et al (2021) Transition metal-based metal–organic frameworks for environmental applications: a review. Environ Chem Lett 19(2):1295–1334. https://doi.org/10.1007/S10311-020-01119-1
Louangsouphom B, Wang X, Song J, Wang X (2019) Low-temperature preparation of a N-TiO2/macroporous resin photocatalyst to degrade organic pollutants. Environ Chem Lett 17:1061–1066. https://doi.org/10.1007/S10311-018-00827-Z/FIGURES/3
Lyu J, Zhu L, Burda C (2014) Considerations to improve adsorption and photocatalysis of low concentration air pollutants on TiO2. Catal Today 225:24–33. https://doi.org/10.1016/J.CATTOD.2013.10.089
MacArthur E (2017) Beyond plastic waste. Science 358:843
Madima N, Mishra SB, Inamuddin I, Mishra AK (2020) Carbon-based nanomaterials for remediation of organic and inorganic pollutants from wastewater. A review. Environ Chem Lett 18:1169–1191. https://doi.org/10.1007/s10311-020-01001-0
Maganha de Almeida Kumlien AC, Borrego CM, Balcázar JL (2021) Antimicrobial resistance and bacteriophages: an overlooked intersection in water disinfection. Trends Microbiol 29:517–527.https://doi.org/10.1016/J.TIM.2020.12.011
Mahmood MA, Baruah S, Anal AK, Dutta J (2012) Heterogeneous photocatalysis for removal of microbes from water. Environ Chem Lett 10:145–151
Malekshahi Byranvand M, Nemati Kharat A, Fatholahi L, Malekshahi Beiranvand Z (2013) A review on synthesis of nano-TiO2 via different methods. J Nanostructures 3:1–9. https://doi.org/10.7508/JNS.2013.01.001
Mandari KK, Son N, Kang M (2021) Ag3PO4-Bi2WO6-TiO2 as a high performance electrocatalyst for oxygen evolution reaction. Appl Surf Sci 566:150681
Mathew S, Ganguly P, Rhatigan S et al (2018) Cu-doped TiO2: visible light assisted photocatalytic antimicrobial activity. Appl Sci 8:2067
Mathew S, Ganguly P, Kumaravel V et al (2020) Effect of chalcogens (S, Se, and Te) on the anatase phase stability and photocatalytic antimicrobial activity of TiO2. Mater Today Proc 33:2458–2464
Matsuura R, Lo C-W, Wada S et al (2021) SARS-CoV-2 disinfection of air and surface contamination by TiO2 photocatalyst mediated damage to viral morphology, RNA, and protein. Viruses 13:942
McEvoy JG, Zhang Z (2014) Antimicrobial and photocatalytic disinfection mechanisms in silver-modified photocatalysts under dark and light conditions. J Photochem Photobiol C Photochem Rev 19:62–75
Mehrotra RC, Singh A (1997) Recent trends in metal alkoxide chemistry. Prog Inorg Chem 46:239–454. https://doi.org/10.1002/9780470166475.CH4
Meng X, Ouyang S, Kako T et al (2014) Photocatalytic CO2 conversion over alkali modified TiO2 without loading noble metal cocatalyst. Chem Commun 50:11517–11519. https://doi.org/10.1039/C4CC04848B
Micochova P, Chadha A, Hesseloj T et al (2021) Rapid inactivation of SARS-CoV-2 by titanium dioxide surface coating. Wellcome Open Res 6:56
Mikrovalov V (2011) Microwave-assisted non-aqueous synthesis of ZnO nanoparticles. Mater Tehnol 45:173–177
Mohan L, Dennis C, Padmapriya N et al (2020) Effect of electrolyte temperature and anodization time on formation of TiO2 nanotubes for biomedical applications. Mater Today Commun 23:101103. https://doi.org/10.1016/J.MTCOMM.2020.101103
Mollabashi V, Farmany A, Alikhani MY et al (2020) Effects of TiO2-coated stainless steel orthodontic wires on streptococcus mutans bacteria: a clinical study. Int J Nanomed 15:8759
Möllmann A, Gedamu D, Vivo P et al (2019) Highly compact TiO2 films by spray pyrolysis and application in perovskite solar cells. Adv Eng Mater 21:1801196. https://doi.org/10.1002/ADEM.201801196
Moore CJ (2008) Synthetic polymers in the marine environment: a rapidly increasing, long-term threat. Environ Res 108:131–139
Moreira AJ, Campos LO, Maldi CP et al (2020) Photocatalytic degradation of Prozac mediated by TiO2 nanoparticles obtained via three synthesis methods: sonochemical, microwave hydrothermal, and polymeric precursor. Environ Sci Pollut Res 27(21):27032–27047. https://doi.org/10.1007/S11356-020-08798-X
Morin-Crini N, Lichtfouse E, Fourmentin M et al (2022) Removal of emerging contaminants from wastewater using advanced treatments. A review. Environ Chem Lett 1–43
Muniandy SS, Kaus NHM, Jiang Z-T et al (2017) Green synthesis of mesoporous anatase TiO2 nanoparticles and their photocatalytic activities. RSC Adv 7:48083–48094. https://doi.org/10.1039/C7RA08187A
Munjal G, Dwivedi G, ANB (2014) Adsorption studies of methylene blue on TiO2 nanoparticles: experimental and mathematical modeling. https://doi.org/10.7763/IPCBEE
Nabi G, Raza W, Tahir MB (2020a) Green synthesis of TiO2 nanoparticle using cinnamon powder extract and the study of optical properties. J Inorg Organomet Polym Mater 30:1425–1429. https://doi.org/10.1007/S10904-019-01248-3
Nabi I, Li K, Cheng H et al (2020b) Complete photocatalytic mineralization of microplastic on TiO2 nanoparticle film. Iscience 23:101326
Nadeem M, Tungmunnithum D, Hano C et al (2018) The current trends in the green synthesis of titanium oxide nanoparticles and their applications. Green Chem Lett Rev 11:492–502. https://doi.org/10.1080/17518253.2018.1538430
Narayan MR, Raturi A (2012) Deposition and characterisation of titanium dioxide films formed by electrophoretic deposition. Int J Mater Eng Innov 3:17–31. https://doi.org/10.1504/IJMATEI.2012.044447
Narkevica I, Stradina L, Stipniece L et al (2017) Electrophoretic deposition of nanocrystalline TiO2 particles on porous TiO2-x ceramic scaffolds for biomedical applications. J Eur Ceram Soc 37:3185–3193. https://doi.org/10.1016/J.JEURCERAMSOC.2017.03.053
Nateq MH, Ceccato R (2019) Sol-Gel synthesis of TiO2 nanocrystalline particles with enhanced surface area through the reverse micelle approach. Adv Mater Sci Eng. https://doi.org/10.1155/2019/1567824
Ng J, Zhang X, Zhang T et al (2010) Construction of self-organized free-standing TiO2 nanotube arrays for effective disinfection of drinking water. J Chem Technol Biotechnol 85:1061–1066. https://doi.org/10.1002/JCTB.2395
Nguu J, Nyongesa F, Musembi R, Aduda B (2018) Electrophoretic deposition and characterization of TiO2/Nb2O5 composite thin films for dye sensitized solar cells. J Mater Phys Chem 6:1–8
Nguyen DC, Doan TLL, Prabhakaran S et al (2021) Hierarchical Co and Nb dual-doped MoS2 nanosheets shelled micro-TiO2 hollow spheres as effective multifunctional electrocatalysts for HER, OER, and ORR. Nano Energy 82:105750
Noh W, Jo S, Kim J, Lee TS (2021) Visible light driven asymmetric TiO2 based photocatalytic micromotor hybridized with a conjugated polyelectrolyte and glucose oxidase. Langmuir
Nyamukamba P, Okoh O, Mungondori H et al (2018) Synthetic methods for titanium dioxide nanoparticles: a review. Titan Dioxide Mater Sustain Environ. https://doi.org/10.5772/INTECHOPEN.75425
Nyongesa F, Aduda B (2017) Electrophoretic deposition of titanium dioxide thin films for photocatalytic water purification systems. Adv Mater 6:31. https://doi.org/10.11648/J.AM.20170604.11
Ochedi FO, Liu D, Yu J et al (2021) Photocatalytic, electrocatalytic and photoelectrocatalytic conversion of carbon dioxide: a review. Environ Chem Lett 19:941–967
Ojemaye MO, Adefisoye MA, Okoh AI (2020) Nanotechnology as a viable alternative for the removal of antimicrobial resistance determinants from discharged municipal effluents and associated watersheds: a review. J Environ Manag 275:111234. https://doi.org/10.1016/J.JENVMAN.2020.111234
Ola O, Maroto-Valer MM (2015) Review of material design and reactor engineering on TiO2 photocatalysis for CO2 reduction. J Photochem Photobiol C Photochem Rev 24:16–42. https://doi.org/10.1016/J.JPHOTOCHEMREV.2015.06.001
Omar TFT, Ahmad A, Aris AZ, Yusoff FM (2016) Endocrine disrupting compounds (EDCs) in environmental matrices: Review of analytical strategies for pharmaceuticals, estrogenic hormones, and alkylphenol compounds. TrAC Trends Anal Chem 85:241–259
Panchal D, Sharma A, Mondal P et al (2021) Heterolayered TiO2@layered double hydroxide-MoS2 nanostructure for simultaneous adsorption-photocatalysis of co-existing water contaminants. Appl Surf Sci 553:149577. https://doi.org/10.1016/J.APSUSC.2021.149577
Pang LX, Wang XY, De TX (2015) Enhanced photocatalytic performance of porous TiO2 nanobelts with phase junctions. Solid State Sci 39:29–33. https://doi.org/10.1016/J.SOLIDSTATESCIENCES.2014.11.004
Pantidos N, Horsfall L (2014) Biological synthesis of metallic nanoparticles by bacteria, fungi and plants. J Nanomed Nanotechnol. https://doi.org/10.4172/2157-7439.1000233
Patel G, Patra C, Srinivas SP et al (2021) Methods to evaluate the toxicity of engineered nanomaterials for biomedical applications: a review. Environ Chem Lett 19:4253–4274
Peiris M, Gunasekara T, Jayaweera P, Fernando S (2018) TiO2 nanoparticles from baker’s yeast: a potent antimicrobial. J Microbiol Biotechnol 28:1664–1670. https://doi.org/10.4014/JMB.1807.07005
Pena ME, Korfiatis GP, Patel M et al (2005) Adsorption of As(V) and As(III) by nanocrystalline titanium dioxide. Water Res 39:2327–2337. https://doi.org/10.1016/J.WATRES.2005.04.006
Phattepur H, Siddaiah GB, Ganganagappa N (2019) Synthesis and characterisation of mesoporous TiO2 nanoparticles by novel surfactant assisted sol-gel method for the degradation of organic compounds. Period Polytech Chem Eng 63:85–95. https://doi.org/10.3311/PPCH.11789
Pragada SC, Thalla AK (2021) Polymer-based immobilized Fe2O3–TiO2/PVP catalyst preparation method and the degradation of triclosan in treated greywater effluent by solar photocatalysis. J Environ Manag 296:113305
Prakash J, Sun S, Swart HC, Gupta RK (2018) Noble metals-TiO2 nanocomposites: From fundamental mechanisms to photocatalysis, surface enhanced Raman scattering and antibacterial applications. Appl Mater Today 11:82–135. https://doi.org/10.1016/J.APMT.2018.02.002
Prihod’ko R V, Soboleva NM (2013) Photocatalysis: oxidative processes in water treatment. J Chem 2013
Purkait P, Bhattacharyya A, Roy S et al (2020) Green synthesis of TiO2 nanoparticle: its characterization and potential application in Zoxamide photodegradation. J Water Environ Nanotechnol 5:191–203
Qu X, Lin J, Chaudhary JP et al (2021) Defect enrich ultrathin TiO2 nanosheets for rapid adsorption and visible light mediated PPCPs degradation. Chemosphere 268:128782
Quyen VT, Ha LTT, Thanh DM et al (2021) Advanced synthesis of MXene-derived nanoflower-shaped TiO2@Ti3C2 heterojunction to enhance photocatalytic degradation of Rhodamine B. Environ Technol Innov 21:101286. https://doi.org/10.1016/J.ETI.2020.101286
Rajakumar G, Rahuman AA, Priyamvada B et al (2012) Eclipta prostrata leaf aqueous extract mediated synthesis of titanium dioxide nanoparticles. Mater Lett 68:115–117. https://doi.org/10.1016/J.MATLET.2011.10.038
Ramakrishnan VM, Natarajan M, Santhanam A et al (2018) Size controlled synthesis of TiO2 nanoparticles by modified solvothermal method towards effective photo catalytic and photovoltaic applications. Mater Res Bull 97:351–360. https://doi.org/10.1016/J.MATERRESBULL.2017.09.017
Ranjan S, Ramalingam C (2016) Titanium dioxide nanoparticles induce bacterial membrane rupture by reactive oxygen species generation. Environ Chem Lett 14:487–494
Reis KP, Ramanan A, Whittingham S (2002) Hydrothermal synthesis of sodium tungstates. Chem Mater 2:219–221. https://doi.org/10.1021/CM00009A003
Sakkas VA, Dimou A, Pitarakis K et al (2005) TiO2 photocatalyzed degradation of diazinon in an aqueous medium. Environ Chem Lett 3:57–61. https://doi.org/10.1007/S10311-004-0091-6/TABLES/2
Saravanan A, Kumar PS, Vo DVN et al (2020) Photocatalysis for removal of environmental pollutants and fuel production: a review. Environ Chem Lett 19(1):441–463. https://doi.org/10.1007/S10311-020-01077-8
Šauer P, Stará A, Golovko O et al (2019) Determining the potential of progestins to induce progestagenic activities in the aquatic environment. Environ Pollut Progestins Occur Horm Act Eff Fish
Savun-Hekimouglu B (2020) A review on sonochemistry and its environmental applications. In: Acoustics, pp 766–775
Sengul AB, Asmatulu E (2020) Toxicity of metal and metal oxide nanoparticles: a review. Environ Chem Lett 18:1659–1683
Shang Q, Gao S, Dai G et al (2020) Structure and photocatalytic activity of Ti3+ self-doped TiO2 flower shaped nanospheres. Surfaces Interfaces 18:100426
Sharma G, Thakur B, Naushad M et al (2017) (2017) Applications of nanocomposite hydrogels for biomedical engineering and environmental protection. Environ Chem Lett 161(16):113–146. https://doi.org/10.1007/S10311-017-0671-X
Sharma R, Sarkar A, Jha R et al (2020) Sol-gel–mediated synthesis of TiO2 nanocrystals: Structural, optical, and electrochemical properties. Int J Appl Ceram Technol 17:1400–1409. https://doi.org/10.1111/IJAC.13439
Shu C, Du H, Pu W et al (2021) Trace amounts of palladium-doped hollow TiO2 nanosphere as highly efficient electrocatalyst for hydrogen evolution reaction. Int J Hydrogen Energy 46:1923–1933
Singh AK, Chaudhary V, Singh AK, Sinha SRP (2019a) Effect of TiO2 nanoparticles on electrical properties of chemical vapor deposition grown single layer graphene. Synth Met. https://doi.org/10.1016/J.SYNTHMET.2019.116155
Singh J, Kumar S, Alok A et al (2019b) The potential of green synthesized zinc oxide nanoparticles as nutrient source for plant growth. J Clean Prod 214:1061–1070. https://doi.org/10.1016/J.JCLEPRO.2019.01.018
Slamet, Tristantini D, Valentina, Ibadurrohman M (2013) Photocatalytic hydrogen production from glycerol–water mixture over Pt-N-TiO2 nanotube photocatalyst. Int J Energy Res 37:1372–1381.https://doi.org/10.1002/ER.2939
Speller KA (2021) The photocatalytic degradation of ibuprofen and atenolol using bismuth oxychloride and titanium dioxide
Sridhar V, Park B-W, Guo S et al (2020) Multiwavelength steerable visible light driven magnetic CoO-TiO2 microswimmers. ACS Appl Mater Interfaces 12:24149–24155
Srikanth B, Goutham R, Badri Narayan R et al (2017) Recent advancements in supporting materials for immobilised photocatalytic applications in waste water treatment. J Environ Manag 200:60–78. https://doi.org/10.1016/J.JENVMAN.2017.05.063
Stride JA, Tuong NT (2010) Controlled synthesis of titanium dioxide nanostructures. Solid State Phenom 162:261–294. https://doi.org/10.4028/WWW.SCIENTIFIC.NET/SSP.162.261
Su J, Yu S, Xu M et al (2020) Enhanced visible light photocatalytic performances of few-layer MoS2@TiO2 hollow spheres heterostructures. Mater Res Bull 130:110936. https://doi.org/10.1016/J.MATERRESBULL.2020.110936
Subhapriya S, Gomathipriya P (2018) Green synthesis of titanium dioxide (TiO2) nanoparticles by Trigonella foenum-graecum extract and its antimicrobial properties. Microb Pathog 116:215–220. https://doi.org/10.1016/J.MICPATH.2018.01.027
Sun Z, Kim JH, Zhao Y et al (2011) Rational design of 3D dendritic TiO2 nanostructures with favorable architectures. J Am Chem Soc 133:19314–19317. https://doi.org/10.1021/JA208468D
Thamaraiselvi K, Sivakumar T (2017) Photocatalytic reduction of carbon dioxide by using bare and copper oxide impregnated nano titania catalysts. J Nanosci Nanotechnol 17:313–322. https://doi.org/10.1166/JNN.2017.12421
Theerthagiri J, Senthil RA, Senthilkumar B et al (2017) Recent advances in MoS2 nanostructured materials for energy and environmental applications—a review. J Solid State Chem 252:43–71. https://doi.org/10.1016/J.JSSC.2017.04.041
Tian J, Leng Y, Cui H, Liu H (2015) Hydrogenated TiO2 nanobelts as highly efficient photocatalytic organic dye degradation and hydrogen evolution photocatalyst. J Hazard Mater 299:165–173
Toma FL, Bertrand G, Klein D, Coddet C (2004) Photocatalytic removal of nitrogen oxides via titanium dioxide. Environ Chem Lett 2:117–121
Tong Y, Shi G, Hu G et al (2021) Photo-catalyzed TiO2 inactivates pathogenic viruses by attacking viral genome. Chem Eng J 414:128788
Udom I, Ram MK, Stefanakos EK et al (2013) One dimensional-ZnO nanostructures: synthesis, properties and environmental applications. Mater Sci Semicond Process 16:2070–2083. https://doi.org/10.1016/J.MSSP.2013.06.017
Umapathi A, Kumawat M, Daima HK (2021) Engineered nanomaterials for biomedical applications and their toxicity: a review. Environ Chem Lett 1–24
Vattikuti SVP, Devarayapalli KC, Reddy Nallabala NK et al (2021) Onion ring like carbon and nitrogen from ZIF-8 on TiO2/Fe2O3 nanostructure for overall electrochemical water splitting. J Phys Chem Lett 12:5909–5918
Vigneshwaran S, Sirajudheen P, Karthikeyan P et al (2021) Immobilization of MIL-88(Fe) anchored TiO2-chitosan(2D/2D) hybrid nanocomposite for the degradation of organophosphate pesticide: characterization, mechanism and degradation intermediates. J Hazard Mater 406:124728. https://doi.org/10.1016/J.JHAZMAT.2020.124728
Villaseñor MJ, Ríos Á (2017) Nanomaterials for water cleaning and desalination, energy production, disinfection, agriculture and green chemistry. Environ Chem Lett 16(1):11–34. https://doi.org/10.1007/S10311-017-0656-9
Wang Y, He Y, Lai Q, Fan M (2014) Review of the progress in preparing nano TiO2: an important environmental engineering material. J Environ Sci 26:2139–2177. https://doi.org/10.1016/J.JES.2014.09.023
Wang D, Li Y, Puma GL et al (2015) Mechanism and experimental study on the photocatalytic performance of Ag/AgCl chiral TiO2 nanofibers photocatalyst: the impact of wastewater components. J Hazard Mater 285:277–284
Wang L, Zhao Y, Zhang J (2017a) Photochemical removal of SO2 over TiO2-Based nanofibers by a dry photocatalytic oxidation process. Energy Fuels 31:9905–9914. https://doi.org/10.1021/ACS.ENERGYFUELS.7B01514
Wang X, Ahmad M, Sun H (2017b) Three-dimensional ZnO hierarchical nanostructures: Solution phase synthesis and applications. Materials (basel) 10:1304
Wang L, Kaeppler A, Fischer D, Simmchen J (2019) Photocatalytic TiO2 micromotors for removal of microplastics and suspended matter. ACS Appl Mater Interfaces 11:32937–32944
Wang J, Li Y, Luo YN et al (2020a) New mixed-crystal nanostructure of K3TiOF5/TiO2 with dominant facets for efficient removal of anionic dyes. Ceram Int 46:25598–25602. https://doi.org/10.1016/J.CERAMINT.2020.07.032
Wang Z, Ali Haidry A, Xie L et al (2020b) Acetone sensing applications of Ag modified TiO2 porous nanoparticles synthesized via facile hydrothermal method. Appl Surf Sci 533:147383. https://doi.org/10.1016/J.APSUSC.2020.147383
Wang D, Zhang B, Ding H et al (2021a) TiO2 supported single Ag atoms nanozyme for elimination of SARS-CoV2. Nano Today 40:101243. https://doi.org/10.1016/J.NANTOD.2021.101243
Wang Y, Li J, Wang B et al (2021b) Bi2O2CO3/TiO2 hybrid with 0D/1D nanostructure: design, synthesis and photocatalytic performance. New J Chem 45:6247–6253
Weir A, Westerhoff P, Fabricius L et al (2012) Titanium dioxide nanoparticles in food and personal care products. Environ Sci Technol 46:2242–2250. https://doi.org/10.1021/ES204168D
Wu JM (2004) Low-temperature preparation of titania nanorods through direct oxidation of titanium with hydrogen peroxide. J Cryst Growth 269:347–355. https://doi.org/10.1016/J.JCRYSGRO.2004.05.023
Wu J-M, Zhang T-W, Zeng Y-W et al (2005) Large-scale preparation of ordered titania nanorods with enhanced photocatalytic activity. Langmuir 21:6995–7002. https://doi.org/10.1021/LA0500272
Wu Y, Lu G, Li S (2009) The doping effect of Bi on TiO2 for photocatalytic hydrogen generation and photodecolorization of Rhodamine B. J Phys Chem C 113:9950–9955. https://doi.org/10.1021/JP9009433
Wu Z, Wu Q, Du L et al (2014) Progress in the synthesis and applications of hierarchical flower-like TiO2 nanostructures. Particuology. https://doi.org/10.1016/j.partic.2013.04.003
Wu F, Zhou Z, Hicks AL (2019) Life cycle impact of titanium dioxide nanoparticle synthesis through physical, chemical, and biological routes. Environ Sci Technol 53:4078–4087
Xie W, Pakdel E, Liang Y et al (2020) Natural melanin/TiO2 hybrids for simultaneous removal of dyes and heavy metal ions under visible light. J Photochem Photobiol A Chem 389:112292
Xin Y, Grundmeier G, Keller A (2021) Adsorption of SARS-CoV-2 spike protein S1 at oxide surfaces studied by high-speed atomic force microscopy. Adv Nanobiomed Res 1:2000024
Xu Z, Meng X (2009) Size effects of nanocrystalline TiO2 on As(V) and As(III) adsorption and As(III) photooxidation. J Hazard Mater 168:747–752. https://doi.org/10.1016/J.JHAZMAT.2009.02.084
Xue Z, Zhang W, Yin X et al (2012) Enhanced conversion efficiency of flexible dye-sensitized solar cells by optimization of the nanoparticle size with an electrophoretic deposition technique. RSC Adv 2:7074–7080. https://doi.org/10.1039/C2RA20542D
Yang Y, Ok YS, Kim K-H et al (2017) Occurrences and removal of pharmaceuticals and personal care products (PPCPs) in drinking water and water/sewage treatment plants: a review. Sci Total Environ 596:303–320
Yang L, Hao X, Yu D et al (2021) High visible-light catalytic activity of Bis-PDI-T@ TiO2 for activating persulfate toward efficient degradation of carbamazepine. Sep Purif Technol 263:118384
Yao J, Chen H, Jiang F et al (2017) Titanium dioxide and cadmium sulfide co-sensitized graphitic carbon nitride nanosheets composite photocatalysts with superior performance in phenol degradation under visible-light irradiation. J Colloid Interface Sci 490:154–162
Yildiz T, Yatmaz HC, Öztürk K (2020) Anatase TiO2 powder immobilized on reticulated Al2O3 ceramics as a photocatalyst for degradation of RO16 azo dye. Ceram Int 46:8651–8657. https://doi.org/10.1016/J.CERAMINT.2019.12.098
Yousef A, El-Halwany MM, Barakat NAM et al (2015) CuO-doped TiO2 nanofibers as potential photocatalyst and antimicrobial agent. J Ind Eng Chem 26:251–258
Yu J, Hai Y, Cheng B (2011) Enhanced photocatalytic H2-production activity of TiO2 by Ni(OH)2 cluster modification. J Phys Chem C 115:4953–4958. https://doi.org/10.1021/JP111562D
Yuan Y, Zhang J, Li H et al (2012) Simultaneous removal of SO2, NO and mercury using TiO2-aluminum silicate fiber by photocatalysis. Chem Eng J 192:21–28. https://doi.org/10.1016/J.CEJ.2012.03.043
Zhang Y, Ma H, Yi M et al (2017) Magnetron-sputtering fabrication of noble metal nanodots coated TiO2 nanoparticles with enhanced photocatalytic performance. Mater Des 125:94–99. https://doi.org/10.1016/J.MATDES.2017.03.084
Zhang Y, Wang L, Zhang N, Zhou Z (2018) Adsorptive environmental applications of MXene nanomaterials: a review. RSC Adv 8:19895–19905. https://doi.org/10.1039/C8RA03077D
Zhang J, Yan M, Sun G, Liu K (2021) Simultaneous removal of Cu (II), Cd (II), Cr (VI), and rhodamine B in wastewater using TiO2 nanofibers membrane loaded on porous fly ash ceramic support. Sep Purif Technol 272:118888
Zhu Y, Chen F (2014) Microwave-assisted preparation of inorganic nanostructures in liquid phase. Chem Rev 114:6462–6555. https://doi.org/10.1021/CR400366S
Zhu Y, Feng Y, Chen S et al (2020) Carbon nitride nanotube-based materials for energy and environmental applications: a review of recent progresses. J Mater Chem A 8:25626–25648. https://doi.org/10.1039/D0TA08892G
Zhu Y, Lu Y, Yu H et al (2021) Super-hydrophobic F-TiO2@ PP membranes with nano-scale “coral”-like synapses for waste oil recovery. Sep Purif Technol 267:118579
Acknowledgements
Authors wish to thank Sathyabama Institute of Science and Technology for the support.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of Interest
The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Arun, J., Nachiappan, S., Rangarajan, G. et al. Synthesis and application of titanium dioxide photocatalysis for energy, decontamination and viral disinfection: a review. Environ Chem Lett 21, 339–362 (2023). https://doi.org/10.1007/s10311-022-01503-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10311-022-01503-z