Abstract
This paper presents a review of previous work conducted as regards to the machining of miniature gears by spark erosion machining (SEM) process and its variants. Miniature gears are key components of various small devices. Their proper function requires the selection of an appropriate manufacturing and/or finishing process that will deliver the required fit for purpose quality. Spark-erosion-based machining processes have a proven track record to impart the relevant quality characteristics and to minimize the number of operations required. This paper commences with an introduction to miniature gears before outlining the spark erosion machining of gears. Details as regards to previous efforts conducted on machining of these gears by SEM-based processes are presented before selected future research trends, directions and avenues for possible future research are offered. This paper focuses exclusively on SEM of miniature gears even though it is noted that similar research work on macrogears is also limited. This review paper aims to facilitate an overall view of all the available literature on spark erosion machining of miniature gears in a single article, to promote the technology and to provide a road map to researchers for making efforts towards exploring these technologies further.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Davis JR (2005) Gear materials, properties and manufacture. ASM International, Ohio
Gupta K, Jain NK (2013) Manufacturing of high quality miniature gears by wire electric discharge machining. Book Chapter in DAAAM International Scientific Book, Chapter-40, 679–696, B. Katalinic (Ed.), Published by DAAAM International, Vienna, Austria, ISBN 978–3–901509–94–0, ISSN 1726–9687
Townsend DP (2011) Dudley’s gear handbook. Tata McGraw-Hill Publishing Company, New Delhi
Bhushan B (2013) Introduction to tribology. Willey, New York
Walraven J (2003) Failure mechanisms in MEMS. Proceedings of International Test Conference, Charlotte, USA
Gupta K, Jain NK (2014) On surface integrity of miniature spur gears manufactured by wire electrical discharge machining. Int J Adv Manuf Technol 72(9–12):1735–1745
Hsu TR (2008) MEMS and microsystems design, manufacture and nanoscale engineering. Wiley, New Jersey
Masuzawa T (2000) State of the art of micromachining. Keynote Paper CIRPAnn 49(2):473–488
Grzesik W (2008) Advanced machining processes of metallic materials. Elsevier, Oxford
Gupta K, Jain NK (2013) On micro-geometry of miniature gears manufactured by WEDM. Mater Manuf Process 28(10):1153–1159
Di S, Haung R, Chi G (2006) Study on micro-machining by micro-WEDM. Proceedings of the 1st international IEEE Conference on Nano/Micro Engineered and Molecular systems, Zhuhai, China
Ali MY, Mohammad AS (2008) Experimental study of conventional WEDM for micro-fabrication. Mater Manuf Process 23(7):641–645
McGeough JA (1988) Advanced methods of machining. Chapman and Hall Ltd, London
Jain VK (2002) Advanced machining processes. Allied Publishers, New Delhi
Ho KH, Newman ST (2003) State of the art electrical discharge machining (EDM). Int J Mach Tools Manuf 43(13):1287–1300
Hocheng H, Tsai HY (2013) Advanced analysis of non-traditional machining. Springer, London
Ho KH, Newman ST, Rahimifard S, Allen RD (2004) Start of the art in wire electrical discharge machining. Int J Mach Tools Manuf 44(12–13):1247–1259
Gupta K, Jain NK (2014) Comparative study of wire-EDM and hobbing for manufacturing high quality miniature gears. Mater Manuf Process 29:1470–1476
Bhuiyan M, Shihab B (2014) Development of copper based miniature electrostatic actuator using WEDM with low actuation voltage. Microsyst Technol. doi:10.1007/s00542-014-2360-z
Yan J, Uchida K, Yoshihara N, Kuriyagawa T (2009) Fabrication of micro end mills by wire-EDM and some micro cutting tests. J Micromech Microeng 19:025004, 9 pp
Dokania AK, Pelle M, Kruit P (2008) Fabrication of miniaturized Schottky emitter by wire electrical discharge machining (WEDM). Microelectron Eng 85:1031–1034
Uhlmann E, Piltz S, Doll U (2005) Machining of micro/miniature dies and moulds by electrical discharge machining—recent development. J Mater Process Technol 167:488–493
Takeuchi H, Nakamura K, Shimizu N, Shibaike N (2000) Optimization of mechanical interface for a practical micro-reducer. Proceedings of 13th IEEE International Conference on Micro Electro Mechanical Systems, Miyazaki, Japan
Takhata K, Shibaike N, Guckel H (2000) High-aspect-ratio WC-Co microstructure produced by the combination of LIGA and micro-EDM. Microsyst Technol 6:175–178
Takhata K, Gianchandani YB (2002) J Micro Mech Syst 11(2):102–110
Hori K, Murata Y (1994) Wire electrical discharge machining of micro-involute gears. Trans Jpn Soc Mech Eng Ser C 60(579):3957–3962
Suzumori K, Hori K (1997) Micro electrostatic wobble motor with toothed electrodes. Proceedings of 10th International Workshop on Micro Electro Mechanical Systems, Nagoya, Japan. IEEE, 227–232
Benavides GL et al (2002) High aspect ratio meso-scale parts enabled by wire micro-EDM. Microsyst Technol 8:395–401
Schoth A, Forster R, Menz W (2005) Micro wire EDM for high aspect ratio 3D microstructuring of ceramics and metals. Microsyst Technol 11:250–253
Ali MY et al (2010) Comparative study of conventional and micro-WEDM based on machining of meso/micro sized spur gear. Int J Precis Eng Manuf 11(5):779–784
Gupta K (2014) Experimental investigations on manufacturing of high quality miniature gears by wire electric discharge machining. Ph.D. Thesis, Indian Institute of Technology Indore, India
Gupta K, Choube SK, Jain NK (2014) Exploring wire-EDM for manufacturing the high quality meso-gears. Proc Math Sci 5:1755–1760
Gupta K, Jain NK (2013) Deviations in geometry of miniature gears fabricated by wire electrical discharge machining. Proceedings of International Mechanical Engineering Congress & Exposition (IMECE 2013) of ASME, V010T11A047, Nov. 13–21, 2013, San Diego, USA
Gupta K, Jain NK (2013) On productivity of wire electric discharge machining for manufacturing of miniature gears. Proceedings of 2nd International Conference on Intelligent Robotics, Automation and Manufacturing 2013 (IRAM 2013), 428–439, Dec. 16–18, 2013, Indore, INDIA
Gupta K, Jain NK (2014) Analysis and optimization of the surface finish of wire electrical discharge machined miniature gears. Proc IMechE B J Eng Manuf 228(5):673–681
Gupta K, Jain NK (2014) Analysis and optimization of the micro-geometry of miniature gears manufactured by wire electric discharge machining. Precis Eng 38(4):728–737
Talon JLH et al (2010) Manufacturing of a spur tooth gear in Ti-6Al-4V by electrical discharge. Comput Aided Des 42:221–230
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Gupta, K., Jain, N.K. & Laubscher, R.F. Spark erosion machining of miniature gears: a critical review. Int J Adv Manuf Technol 80, 1863–1877 (2015). https://doi.org/10.1007/s00170-015-7130-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-7130-2