Abstract
This paper discusses the comparison of micro machining process using conventional and micro wire electrical discharge machining (WEDM) for fabrication of miniaturized components. Seventeen toothed miniaturized spur gear of 3.5 and 1.2 mm outside diameter were fabricated by conventional and micro WEDM respectively. The process parameters for both conventional and micro WEDM were optimized by preliminary experiments and analysis. The gears were investigated for the quality of surface finish and dimensional accuracy which were used as the criteria for the process evaluation. An average surface roughness (Ra) of 50 nm and dimensional accuracy of 0.1–1 µm were achieved in micro WEDM. Whenever applied conventional WEDM for meso/micro fabrication, a Ra surface roughness of 1.8 µm and dimensional accuracy of 2–3 µm were achieved. However, this level of surface roughness and dimensional accuracy are acceptable in many applications of micro engineering. A window of conventional WEDM consisting of low energy discharge parameters is identified for micromachining.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Takahata, K., Shibaike, N. and Gukel, H., “High Aspect Ratio WC-Co Microstructure Produced by the Combination of LIGA and MicroEDM,” Microsystem Technologies, Vol. 6, No. 5, pp. 175–178, 2000.
Weng, F. T. and Her, M. G., “Study of the Batch Production of Micro Parts Using the EDM Process,” International Journal of Advanced Manufacturing Technology, Vol. 19, No. 4, pp. 266–270, 2000.
Schoth, A., Forster, R. and Menz, W., “Micro Wire EDM for High Aspect Ratio 3D Microstructuring of Ceramics and Metals,” Microsystem Technologies, Vol. 11, No. 4–5, pp. 250–253, 2005.
Liao, Y. S. and Yu, Y. P., “Study of Specific Discharge Energy in WEDM and its Application,” International Journal of Machine Tools and Manufacture, Vol. 44, No. 12–13, pp. 1373–1380, 2004.
Jung, J. W., Ko, S. H., Jeong, Y. H., Min, B. K. and Lee, S. J., “Real-time Gap Control for Micro-EDM: Application in a Microfactory,” Int. J. Precis. Eng. Manuf., Vol. 9, No. 1, pp. 3–6, 2008.
Liao, Y. S., Huangb, J. T. and Chena, Y. H., “A Study to Achieve a Fine Surface Finish in Wire-EDM,” Journal of Materials Processing Technology, Vol. 149, No. 1–3, pp. 165–171, 2004.
Han, F., Jiang, J. and Yu, D., “Influence of Machining Parameters on Surface Roughness in Finish Cut of WEDM,” International Journal of Advanced Manufacturing Technology, Vol. 34, No. 5–6, pp. 538–546, 2007.
Benavides, G. L., Bieg, L. F., Saavedra, M. P. and Bryce, E. A., “High Aspect Ratio Meso-Scale Parts Enabled by Wire Micro-EDM,” Microsystem Technologies, Vol. 8, No. 6, pp. 395–401, 2002.
Tosun, N., Cogun, C. and Pihtili, H., “The Effect of Cutting Parameters on Wire Crater Sizes in Wire EDM,” International Journal of Advanced Manufacturing Technology, Vol. 21, No. 10–11, pp. 857–865, 2003.
Gökler, I. M. and Ozanözgü, A. M., “Experimental Investigation of Effects of Cutting Parameters on Surface Roughness in the WEDM,” International Journal of Machine Tool and Manufacture, Vol. 40, No. 13, pp. 1831–1848, 2000.
Kim, Y. T., Park, S. J. and Lee, S. J., “Micro/Meso-scale Shapes Machining by Micro EDM Process,” Int. J. Precis. Eng. Manuf., Vol. 6, No. 2, pp. 5–11, 2005.
Lim, J. H., Je, S. U., Ryu, S. H. and Chu, C. N., “Distortion of the Bottom Surface in Micro Cavity Machining Using MEDM,” Int. J. Precis. Eng. Manuf., Vol. 6, No. 4, pp. 44–48, 2005.
Tan, P. C., Yeo, S. H. and Tan, Y. V., “Effects of Nanopowder Additives in Micro-electrical Discharge Machining,” Int. J. Precis. Eng. Manuf., Vol. 9, No. 3, pp. 22–26, 2008.
Ruprecht, R., Gietzelt, T., Müller, K., Piotter, V. and Haußelt, J., “Injection Molding of Microstructured Components from Plastics, Metals and Ceramics,” Microsystem Technologies, Vol. 8, No. 4–5, pp. 351–358, 2002.
Ong, N. S., Zhang, H. and Woo, W. H., “Plastic Injection Molding of High-Aspect Ratio Micro-Rods,” Materials and Manufacturing Processes, Vol. 21, No. 8, pp. 824–831, 2006.
Loh, N. H., Tor, S. B., Tay, B. Y., Murakoshi, Y. and Maeda R., “Fabrication of Micro Gear by Micro Powder Injection Molding,” Microsystem Technologies, Vol. 14, No. 1, pp. 43–50, 2007.
Dengen, R. and Siatter, R., “The Micro Harmonic Drive: A High Precision Micro Gear System Miniaturized by LIGA,” Proc. 9th International Symposium on Transport Phenomena and Dynamics of Rotating Machinery, pp. 1–6, 2002.
Ali, M. Y. and Ammar, S. M., “Experimental Study of Conventional WEDM for Microfabrication,” Materials and Manufacturing Processes, Vol. 23, No. 7, pp. 641–645, 2008.
Ali, M. Y., Rashidah, N. I. and Azima, N. A., “Wire Electrical Discharged Machining for Microfabrication,” Proc. 7th International Conference on Mechanical Engineering, pp. ICME07–AM-08, 2007.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Ali, M.Y., Mustafizul Karim, A.N., Adesta, E.Y.T. et al. Comparative study of conventional and micro WEDM based on machining of meso/micro Sized Spur Gear. Int. J. Precis. Eng. Manuf. 11, 779–784 (2010). https://doi.org/10.1007/s12541-010-0092-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-010-0092-2