Abstract
Fundamental understanding of the relationship among process, microstructure, and mechanical properties is essential to solder alloy design, soldering process development, and joint reliability prediction and optimization. This research focused on the process-structure-property relationship in eutectic Sn-Ag/Cu solder joints. As a Pb-free alternative, eutectic Sn-Ag solder offers enhanced mechanical properties, good wettability on Cu and Cu alloys, and the potential for a broader range of application compared to eutectic Sn-Pb solder. The relationship between soldering process parameters (soldering temperature, reflow time, and cooling rate) and joint microstructure was studied systemati-cally. Microhardness, tensile shear strength, and shear creep strength were measured and the relationship between the joint microstructures and mechani-cal properties was determined. Based on these results, low soldering tempera-tures, fast cooling rates, and short reflow times are suggested for producing joints with the best shear strength, ductility, and creep resistance.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
S. Jin,JOM 45, 13 (1993).
L.E. Felton, C.H. Raeder, D.B. Knorr and C.H. Havasy,Proc. 1992 Intl. Electronics Manu. Symp. (1992), p. 300.
C. Melton,Proc. 1993 IEEE Intl. Symp. Electronics and the Environment, (1993), p. 94.
W.L. Winterbottom,JOM 45, 20 (1993).
W.J. Tomlinson and A. Fullylove,J. Mater. Sci. 27, 5777 (1992).
S.K. Kang and A.K. Sarkhel,J. Electron. Mater. 23, 701 (1994).
J.S. Hwang and R.M. Vargas,Soldering & Surface Mount Techn. 5,38(1990).
M. Harada and R. Satoh,IEEE/CHMT 13, 736 (1990).
J. Beuers and G. Ptashek,Proc. IEEE/ISHM’92 Symp. (1992), p. 120.
D. Shangguan and A. Achari,Proc. 16th IEEE/CPMT Intl. Electronics Manu. Technology Symp. (1994), p. 25.
W. Yang, L.E. Felton and R.W. MessIer, Jr.,J. Electron. Mater. 23, 765 (1994).
W. Yang, L.E. Felton and R.W. Messlier, Jr.,Proc. Conf. Advanced Joining Technologies for New Materials II, (1994).
M. McCormack, S. Jin and G.W. Kammlott,Appl. Phys. Lett. 64, 580 (1994).
F. Dirnfeld and J.J. Ramon,Welding Journal 69, 373s (1990).
M. Nylen and S. Norgren,Soldering & Surface Mount Technology, 5 15 (1990).
Z. Mei, J.W. Morris, Jr., M.C. Shine and T.S.E. Summers,J. Electron. Mater. 20, 599 (1991).
D. Frear, D. Grivas and J.W. Morris, Jr.,J. Electron. Mater. 16, 181 (1987).
D. Frear, F.M. Hosking and P.T. Vianco,Proc. Materials Developments in Microelectronic Packaging Conf. (1991), p. 229.
L.E. Felton, K. Rajan, P.J. Ficalora and P. Singh,Proc. Materials Developments in Microelectronic Packaging Conf. (1991), p. 23.
W.G. Bader,Welding Journal 54, 370s (1975).
K. Fisher,Fundamentals of Solidification (Aedennannsdorf, Switzerland: Tech Trans Publications, 1986).
R.E. Reed-Hill,Physical Metallurgy Principles, Ed., (Boston: PWS-Kent Publishing Company, 1992).
A.J. Sunwoo, J.W.MorrisJr. and G.K Lucey, Jr.,Metall. Trans. A, 23A, 1323(1992).
E.K. Ohriner,Welding Journal 66, 191s (1987).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Yang, W., Felton, L.E. & Messler, R.W. The effect of soldering process variables on the microstructure and mechanical properties of eutectic Sn-Ag/Cu solder joints. J. Electron. Mater. 24, 1465–1472 (1995). https://doi.org/10.1007/BF02655465
Received:
Revised:
Issue Date:
DOI: https://doi.org/10.1007/BF02655465