Abstract
This research discusses the methodology of developing a symbolic closed form solution that describes the dynamic stability of multiflute end milling. A solution of this nature facilitates machine tool design, machining parameter planning, process monitoring, diagnostics, and control. This study establishes a compliance feedback model that describes the dynamic behavior of regenerative chatter for multiflute tool-work interaction. The model formulates the machining dynamics based upon the interconnecting relationship of the tool geometry and the machining system compliance. The tool geometry characterises the cutting forces as a function of the process parameters and the material properties, while two independent vibratory modules, the milling tool and the workpiece, represent the machining system compliance. The compliance feedback model allows the development of a corresponding characteristic equation. By investigating the roots of the characteristic equation, this research symbolically expresses the stability of the system as a function of the cutting parameters, the tool geometry, the workpiece geometry, and the vibrational characteristics of the machine tool. Machining experimentation examining the fidelity of the regenerative chatter model is discussed. The dynamic cutting forces, cutting vibration, and surface finish of the machining process confirm the validity of the analytical prediction.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Abbreviations
- b :
-
damping coefficient: mass-spring-damper representation
- b e :
-
equivalent damping coefficient: mass-spring-damper representation
- C :
-
compliance element
- CWD :
-
chip with density function
- D :
-
diameter of cutter
- d a :
-
axial depth of cut
- d r :
-
radial depth of cut
- \(\bar F_{x,y}\) :
-
average total cutting force
- K r :
-
radial specific cutting pressure constant
- K t :
-
tangential specific cutting pressure constant
- k :
-
spring constant
- k e :
-
equivalent spring constant
- m :
-
mass: mass-spring-damper representation
- m e :
-
equivalent mass: mass-spring-damper representation
- n :
-
number of flutes on the cutter
- p x,y :
-
elemental cutting forces
- P 1,2 :
-
elemental cutting force functions
- R :
-
cutter radius
- s :
-
Laplace variable
- TS :
-
tooth sequencing function
- \(\mathop {t_c }\limits_\_\) :
-
chip thickness
- t c :
-
average chip thickness
- t x :
-
feed per tooth
- α:
-
helix angle
- Δ x :
-
actual displacement of cutter tip
- δ:
-
unit impulse function
- ω d :
-
damped circular frequency of vibration
- ζ:
-
damping ratio
- Ω:
-
spindle speed
References
J. Tlusty, “Analysis of the state of research in cutting dynamics”,Annals of the CIRP 27(2), pp. 583–589, 1978.
J. Tlusty and F. Ismail, “Basic non-linearity in machining chatter”,Annals of the CIRP 30(1), pp. 299–304, 1981.
J. Tlusty and F. Ismail, “Special aspects of chatter in milling”,Transactions of the ASME 105, pp. 24–32, January 1983.
I. E. Minis, E. B. Magrab and I. O. Pandelidis, “Improved methods for the prediction of chatter in turning, Part 3: a generalized linear theory”,Transactions of the ASME 112, pp. 28–35, February 1990.
I. Minis and R. Yanushevsky, “A new theoretical approach for the prediction of machine tool chatter in milling”,Journal of Engineering for Industry 115, pp. 1–8, February 1993.
J. J. Junz Wang, Steven Liang and Wayne Book, “Analysis of milling forces via angular convolution”,Sensors, Controls, and Quality Issues in Manufacturing, ASME, pp. 135–150, 1991.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Shorr, M.J., Liang, S.Y. Chatter stability analysis for end milling via convolution modelling. Int J Adv Manuf Technol 11, 311–318 (1996). https://doi.org/10.1007/BF01845689
Issue Date:
DOI: https://doi.org/10.1007/BF01845689