Abstract
The aim of this paper is to estimate soil moisture at spatial level by applying geostatistical techniques on the point observations of soil moisture in parts of Solani River catchment in Haridwar district of India. Undisturbed soil samples were collected at 69 locations with soil core sampler at a depth of 0–10 cm from the soil surface. Out of these, discrete soil moisture observations at 49 locations were used to generate a spatial soil moisture distribution map of the region. Two geostatistical techniques, namely, moving average and kriging, were adopted. Root mean square error (RMSE) between observed and estimated soil moisture at remaining 20 locations was determined to assess the accuracy of the estimated soil moisture. Both techniques resulted in low RMSE at small limiting distance, which increased with the increase in the limiting distance. The root mean square error varied from 7.42 to 9.77 in moving average method, while in case of kriging it varied from 7.33 to 9.99 indicating similar performance of the two techniques.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
Soil moisture plays a key role in various hydrological, environmental and agricultural applications. It governs infiltration and surface runoff, since the hydraulic conductivity of soil depends upon the available water content in the soil. It also influences the plant evapotranspiration thereby making it an important component of water balance equation. Knowledge of spatial distribution of soil moisture is essential for predicting runoff at the catchment scale (Fitzjohn et al. 1998; Western et al. 1999, 2001) and in the design of irrigation scheduling (Blonquist et al. 2006; Vellidis et al. 2008). For optimum irrigation practices, it becomes essential to accurately estimate the soil moisture. Moreover, to model overland flow from a precipitation event over a catchment, the estimation of antecedent soil moisture is a prerequisite.
Various studies (Oevelen 1998; Feng et al. 2004; De Lannoy et al. 2006) have shown that hydrometeorological conditions, soil properties and land cover govern the presence of moisture in the unsaturated zone of soil. These studies (Anderson and Burt 1977, 1978; Beven and Kirkby 1979; Chorley 1980; Moore et al. 1988; Wood et al. 1990; 1993; Bárdossy and Lehmann 1998) have shown that soil moisture is highly variable both in space and time. The characteristics of spatial variability of soil moisture depend on the scale of observation (Lakhankar et al. 2010).
For estimation of soil moisture at catchment level using observed point observations of soil moisture data, various interpolation methods such as weighted average, inverse distance interpolation, spline interpolation and kriging can be employed (Bárdossy and Lehmann 1998; Thattai and Islam 2000). For the estimation of soil moisture at spatial scale using observed point observations of soil moisture data, various interpolation techniques such as weighted average, inverse distance interpolation, spline interpolation and kriging can be employed. Dynamic multiple linear regression technique was adopted by Wilson et al. (2005) to compute soil moisture using topographic attributes. Downer and Ogden (2003) estimated soil moisture using gridded surface subsurface hydrologic analysis (GSSHA) hydrologic model with a root mean square error of 0.1. Pandey and Pandey (2010) mapped soil moisture in Udaipur, India, applying ordinary kriging. The study concluded that the krigged values were consistent and true representative of soil moisture values. Said et al. (2008) have experimented with ANN method to estimate soil moisture in the Solani River catchment. However, application of geostatistical interpolation technique is new in the study area.
The aim of this paper is to evaluate the efficacy of geostatistical interpolation techniques and to estimate soil moisture at spatial level from the in situ observed soil moisture data at point locations. The selection of an estimation technique may be site specific. Therefore, an evaluation of the techniques may be necessary to identify the appropriate one to be adopted in the prediction model. In the present study, two interpolation techniques, namely, moving average and ordinary kriging, have been evaluated to estimate the soil moisture at spatial scale.
Study area
The study area is a part of the Solani River catchment in the vicinity of Haridwar district in Uttarakhand State of India. The area lies between 77.48°E, 29.45°N and 78.03°E, 29.55°N at an average elevation of 268 m above mean sea level. Location map of the study area is shown in Fig. 1. Average annual rainfall of the region is 1,170 mm and the temperature varies approximately from 1 °C in winter to 45 °C in the summer. Texture of soil influences the infiltration, surface runoff, evapotranspiration, interflow, and aquifer recharge. Study by Kumar et al. (2012) indicates that the type of soil in the catchment area is loam (US Bureau of Soil and PRA Classification) with an average proportion of 50–55 % of sand, 35–42 % silt and 8–15 % clay. Solani River is a seasonal tributary of the Ganges River. Besides Solani River, a few seasonal streams, Ratmau, and Pathri Rao, originating from Shivalik hills (lower Himalayan mountain range) play a significant role in enriching the land fertility in the study area. The study area constitutes three major land cover classes: built-up land, bare soil and vegetated land. A significant portion of the vegetated land is agricultural with perennial and seasonal crops. Sugarcane is the perennial crop in the area. The summer (period from June to September) crops are paddy, maize and cherry whereas the winter (period from October to March) crops are wheat, mustard and fodder crop berseem.
Field observations were collected during 10–12 Dec 2009 at 69 sample locations in the study area covering about 154 km2. The geographical coordinates of the sample points were recorded with the help of hand held global positioning system (GPS). Of the measured 69 locations, 52 samples were collected from the vegetated land covered with wheat, sugar cane, mustard and berseem crop. The wheat was in early growing stage, whereas the rest of the crops were at matured level. The remaining 17 locations correspond to bare soil fields. Out of 69 locations, 49 locations were considered for the model development whereas remaining 20 locations were kept for model validation. A due representation for vegetated and bare soil samples has been given in model development and its validation. Figure 2 depicts the geographical representation of the soil sampled locations.
The undisturbed soil samples were collected with the help of piston sampler from both bare soil and vegetated surfaces from the upper 0–10 cm thick soil layer. The samples were weighed and then oven-dried at 105 °C for 24 h to compute the volumetric soil moisture content. The observed volumetric soil moisture in the area varied from a minimum 3 % to a maximum of 43 %.
Methodology
A number of interpolation techniques have been used for the analysis of distribution of the soil moisture at spatial scale (Feng et al. 2004; Wilson et al. 2005; Lakhankar et al. 2010). The most common interpolation techniques are moving average, trend surface and kriging (Kratze et al. 2006). The applicability of these techniques depends upon various factors such as distribution of sampled data in the space, the type of surfaces to be generated and tolerance of estimation errors. Hence, an evaluation of these geostatistical techniques may help in arriving at the most appropriate technique for estimation of soil moisture estimation at spatial level in Indian conditions. In the present study, the performance of moving average and kriging geostatistical techniques has been evaluated in estimating soil moisture distribution in a part of Solani River catchment.
Moving average technique
In the present context, moving average operates upon computing weight factor for each observed soil moisture at a sample location considered within a limiting distance, also called as the search radius to estimate soil moisture. The locations lying beyond the specified search radius are not taken into account for the estimation. For each location within the search radius, the distances of all observed soil moisture locations are calculated to determine weight factors. The sampled locations are weighted during interpolation such that the influence of one location relative to the other declines with distance from the location at which the moisture is to be estimated. Hence, the locations closer to it will have larger weight than those obtained at locations farther from it. The soil moisture at a location may thus, be estimated as,
where n is the number of observed soil moisture locations within the search radius, \(W_{i}\) and \(M_{\text{voi}}\) are the weights assigned and the volumetric moisture content in percentage, respectively, at the ith location. The weight \(W_{i}\) for each observed soil moisture location may be computed as,
where \(m\) is the weight exponent, and \(h_{\text{ri}}\) is the relative distance of ith observed soil moisture location from the estimated soil moisture location. The \(h_{\text{ri}}\) is computed as,
where \(h_{i}\) is the distance of ith observed soil moisture location from the estimated soil moisture location, and \(h_{l}\) is the search radius. The accuracy of estimation depends upon the search radius and the weight exponent. Therefore, several trials are conducted before arriving at the acceptable values for the search radius and weight exponents.
The RMSE between the observed and estimated soil moisture at validation locations is computed as,
where \(p\) is the number of locations considered for model validation and \(M_{\text{vo}}\), \(M_{\text{vc}}\) are the observed and estimated moisture contents at those locations respectively.
Kriging
Kriging is a geostatistical data interpolation technique based on the assumption that the data are spatially correlated. Ordinary kriging works on selected theoretical semi-variogram model used for computing semi-variance values at the points where soil moisture is to be estimated. A plot of the calculated semi-variance values against the distance (lags) is known as a semi-variogram. Increasing the lag distance of the semi-variance values consider average over more points, thus decreasing the fluctuations of the experimental semi-variogram. Several theoretical semi-variogram models are possible that include linear, spherical, circular, exponential and Gaussian (Teegavarapu and Chandramouli 2005) to fit over the experimentally constructed semi-variogram. The most suitable semi-variogram model may be found based on the RMS error between the semi-variance values obtained from experimentally observed data and the theoretical model predicted semi-variance values. Often the experimental semi-variogram values do not approach to zero at the origin and intersect the positive y-axis. This is due to the residual or spatially uncorrelated noise, which is also known as the nugget (Kitanidis 1997). The stabilized semi-variogram value is known as the sill, and the distance at which the semi-variogram values approach the sill is called the range.
The general expression to estimate the semi-variance is given as,
where \(\gamma_{(h)}\) is the semi-variance defined over the observed data, \(M_{\text{voi}}\) and \(M_{\text{voj}}\) is the measured moisture at two locations lagged successively by the distance \(h\).
Spatial interpolation using kriging significantly depends on the semi-variogram model used. The appropriate semi-variogram model is usually obtained through experiments. In this study, three semi-variogram models, namely, spherical, Gaussian and exponential, stated in Eqs. (6) to (8), respectively, have been considered.
The parameters, \(C_{0}\) and \(a\) denote nugget and range. The summation of \(C_{0}\) and \(C_{1}\) is referred to as sill and the sill value at range, \(a\), is the desired semi-variance.
In ordinary kriging, having obtained the most appropriate semi-variogram model, the soil moisture values \(M_{\text{vc}}\), at any location can be obtained as a weighted sum of the observed soil moisture values,
where \(W_{i}\) and \(M_{\text{voi}}\) are the weight and observed soil moisture at the ith location, and n is the number of locations within the limiting distance. The \(W_{i}\) are computed by solving the following equations,
and
The matrix form of Eqs. (11) and (12) is given as,
Where \(_{hpi}\) is the distance between the location p where soil moisture is to be estimated, and the location \(i\) where soil moisture is observed. \(\gamma_{(hik)}\) is semi-variance value for the distance between the locations i and k and \(W_{i}\) is the weight for point \(i\). \(\lambda\) is a Lagrange multiplier that is used to minimize the possible estimation error in kriging interpolation.
The limiting distance governs the selection of observed locations around a location considered to estimate the soil moisture. The limiting distance is usually taken as smaller than the range of the selected semi-variogram. Observed locations that lie beyond specified limiting distance are not considered in the interpolation of soil moisture.
Results and discussion
In this paper, an evaluation of soil moisture predicted by two geostatistical techniques, moving average and kriging, was carried out. The success of moving average method depends primarily upon two factors: (1) limiting distance and (2) weight of the exponent. A decrease in limiting distance improves the interpolation accuracy, whereas with the decrease in limiting distance the moving average method may fail to predict soil moisture in regions of scarce observed soil moisture locations. Figure 3a–d shows the estimated distribution of soil moisture using moving average method for limiting distance 1,000, 2,000, 3,000 and 4,000 m, respectively.
It can be seen from Fig. 3a that the method has failed to predict soil moisture at few places in case of small limiting distance. This is due to non-availability of observed sufficient soil moisture locations within the selected limiting distance. However, by increasing the limiting distance to 2,000 m and beyond, the moving average method is able to estimate the soil moisture over the entire study area. It can thus be concluded that for the effective application of moving average method, several experimental trials on limiting distance and weight exponent may therefore be necessary to obtain the optimal limiting distance and the weight exponent, which may also be case dependent.
Table 1 shows the RMSE between the observed soil moisture and the estimated soil moisture at 20 points locations considered to evaluate the interpolation. It can be seen from the table that the RMSE increases with the increase in the limiting distance 1,000–2,000 m. However, a further increase in limiting distance (i.e., 3,000 and 4,000 m) results in decrease in the RMSE. Nevertheless, for a given limiting distance, the impact of weight exponent on estimation of soil moisture appears insignificant, since the RMSE remains unchanged with the variation in weight exponent.
In summary, it can be reiterated that the moving average method has limitation in selecting appropriate limiting distance as the user may have to determine it experimentally. To overcome this limitation, Kitanidis (1997) has proposed the use of ordinary kriging under the domain of semi-variogram model wherein the limiting distance may be taken as less than or equal to the range.
The ordinary kriging method uses semi-variogram model for interpolating point data. In this study, the observed volumetric soil moisture at 49 locations has been used to construct an experimental semi-variogram. Table 2 shows the semi-variance values of these locations at lag distances of selected 1,000 m chosen. It is evident from the table that as the distance between the points pairs increases to 3,000 m, the semi-variance increases. Beyond 3,000 m, these values fluctuate. Hence, pairs of locations beyond this distance are considered to be uncorrelated.
The accuracy of ordinary kriging depends primarily upon the theoretical semi-variogram model employed to fit the experimental semi-variogram. Therefore, three theoretical semi-variogram models, namely, spherical, Gaussian and exponential models have been used in this study.
Different semi-variogram models have been tried over the experimentally constructed semi-variogram to determine the RMSE between the actual and model computed semi-variance values. Initial trials were made by fitting spherical, gaussian and exponential models over the experimentally constructed semi-variogram. Table 3 indicates that spherical model results in the least RMSE at distance 2,000 m.
It can also be seen that as the lag distance increases, the RMSE between the semi-variance values increases. The optimum lag distance has been found to be 2,000 m in case of spherical model.
Figure 4 shows the fit of the three semi-variogram models over the semi-variance values obtained from the experimental semi-variogram. From this figure, it can be seen that the spherical model adequately explains the variation of experimental semi-variance as compared to the other models for the dataset considered. Figure 4 also shows that at a range value of 2,800 m, this semi-variogram model stabilizes. Thus, by taking limiting distance equal or more than 2,800 m will result in a constant semi-variance value for all the points separated by a distance greater than 2,800 m.
The parameters of spherical model (i.e., nugget and sill) have been used to estimate the soil moisture at each grid (i.e., pixel of size 30 m × 30 m) location to reflect the spatial distribution of soil moisture using ordinary kriging. The kriging is performed for the observed soil moisture values at 49 locations and the spherical semi-variogram model to generate the spatial distribution of soil moisture at limiting distances of 1,000, 2,000 and 2,700 m (Fig. 5a–c).
It can be seen from Fig. 5a that kriging method also is unable to estimate soil moisture in regions where observed locations for interpolation are at a greater distance than the limiting distance. However, with the increase in the limiting distance to 2,000 m and beyond, the kriging method is able to estimate the soil moisture distribution entire area.
The RMSE between the estimated soil moisture and the observed soil moisture at the 20 independent locations considered to evaluate the interpolation model are given in Table 4. From Table 4, it can be seen that the RMSE increases with the increase in the limiting distance. The analysis shows that to select the appropriate semi-variogram model for kriging, several trials are required. The limiting distance chosen to krig soil moisture values depends upon the range of the semi-variogram model adopted, which is again a case specific.
Conclusions
Spatial and temporal knowledge of soil moisture is important to effectively model the surface runoff from a river catchment. The moving average and kriging methods were employed to estimate soil moisture at spatial scale in a part of Solani River catchment. Observed soil moisture data at 49 sample locations points were used to estimate soil moisture spatial scale, whereas the soil moisture data at 20 locations were used to validate the results by computing RMSE between the observed and estimated soil moisture using the two methods.
For the dataset used, for small limiting distances, due to non-availability of sufficient observed soil moisture locations within the adopted limiting distance, the moving average method was not able to estimate the soil moisture in the region. The effect of variation in weight exponent was also found insignificant in this method. The kriging method was also unable to estimate soil moisture in regions where observed locations for interpolation were at a distance greater than the limiting distance. However, with the increase in the limiting distance to 2,000 m and beyond, the kriging method was able to estimate the soil moisture distribution entire area. Increase in the limiting distance beyond 1,000 m resulted in increase RMSE in both the cases. From the comparison of the two methods, the kriging appears to be a more practical method due to its dependency on data-constructed semi-variogram.
References
Anderson MG, Burt TP (1977) Automatic monitoring of soil moisture conditions in a hillslope spur and hollow. J Hydrol 33:27–36
Anderson MG, Burt TP (1978) Towards a more detailed field monitoring of variable source areas. Water Resour Res 14:1123–1131
Bárdossy A, Lehmann W (1998) Spatial distribution of soil moisture in a small catchment. Part 1: geostatistical analysis. J Hydrol 206:1–15
Beven KJ, Kirkby MJ (1979) A physically based variable contributing area model of basin hydrology. Hydrol Sci Bull 24(1):43–69
Blonquist JM Jr, Jones SB, Robinson DA (2006) Precise irrigation scheduling for turfgrass using a subsurface electromagnetic soil moisture sensor. Agric Water Manag 84:153–165
Chorley RJ (1980) The hillslope hydrological cycle. In: Kirkby MJ (ed) Hillslope hydrology. Wiley, Chichester, pp 1–42
De Lannoy, Gabriëlle JM, Verhoest Niko EC, Houser Paul R, Gish Timothy J, Van Meirvenne M (2006) Spatial and temporal characteristics of soil moisture in an intensively monitored agricultural detailed field. J Hydrol 331:719–730
Downer CW, Ogden FL (2003) Prediction of runoff and soil moistures at the watershed scale: effects of model complexity and parameter assignment. Water Resour Res 39:1–13
Feng Q, Liu Y, Mikami M (2004) Geostatistical analysis of soil moisture variability in grassland. J Arid Environ 58:357–372
Fitzjohn C, Ternan JL, Williams AG (1998) Soil moisture variability in a semi-arid gully catchment: implications for runoff and erosion control. Catena 32:55–70
Kirkby MJ (1993) Long term interactions between networks and hillslopes. In: Beven K, Kirkby MJ (eds) Channel network hydrology. Wiley, Chichester, pp 256–293
Kitanidis PK (1997) Introduction to Geostatistics: Application to Hydrogeology. University Press, Cambridge
Kratze JF, Hayes DB, Thompson B (2006) Methods for interpolating stream width, depth, and current velocity. Ecol Model 196:256–264
Kumar K, Hari Prasad KS, Arora MK (2012) Estimation of water cloud model vegetation parameters using a genetic algorithm. Hydrol Sci J 57(4):776–789
Lakhankar T, Jones AS, Cynthia LC, Sengupta M, Thomas HVH, Khanbilvardi R (2010) Analysis of large scale spatial variability of soil moisture using a geostatistical method. Sensors 10:913–932
Moore ID, Burch GJ, Mackenzie DH (1988) Topographic effects on the distribution of surface soil wafer and the location of ephemeral gullies. Trans Am Soc Agric Eng 31:1098–1107
Oevelen Van Peter J (1998) Soil moisture variability: a comparison between detailed field measurements and remote sensing measurement techniques. Hydrol Sci J 43:511–520
Pandey V, Pandey PK (2010) Spatial and temporal variability of soil moisture. Int J Geosci 1:87–98
Said S, Kothyari UC, Arora MK (2008) ANN-based soil moisture retrieval over bare and vegetated areas using ERS-2 SAR data. J Hydrol Eng ASCE 13:461–475
Teegavarapu RSV, Chandramouli V (2005) Improved weighting methods, deterministic and stochastic data-driven models for estimation of missing precipitation records. J Hydrol 312:191–220
Thattai D, Islam S (2000) Spatial analysis of remotely sensed soil moisture data. ASCE J Hydrol Eng 5:386–392
Vellidis G, Tucker M, Perry C, Kvien C, Bednarz C (2008) A real-time wireless smart sensor array for scheduling irrigation. Comput Electr Agric 6(1):44–50
Western AW, Grayson RB, Green TR (1999) The Tarrawarra project: high resolution spatial measurement, modelling and analysis of soil moisture and hydrological response. Hydrol Process 13:633–652
Western AW, Bloschl G, Grayson RB (2001) Toward capturing hydrologically significant connectivity in spatial patterns. Water Resour Res 37(1):83–97. doi:10.1029/2000WR900241
Wilson DJ, Western AW, Grayson RB (2005) A terrain and data-based method for generating the spatial distribution of soil moisture. Adv Water Resour 28:43–54
Wood EF, Sivapalan M, Beven KJ (1990) Similarity and scale in catchment storm response. Rev Geophys 28:1–18
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution License which permits any use, distribution, and reproduction in any medium, provided the original author(s) and the source are credited.
About this article
Cite this article
Kumar, K., Arora, M.K. & Hariprasad, K.S. Geostatistical analysis of soil moisture distribution in a part of Solani River catchment. Appl Water Sci 6, 25–34 (2016). https://doi.org/10.1007/s13201-014-0202-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13201-014-0202-x