Abstract
Aluminum alloys were used in engineering applications, such as aircraft, aerospace, automobiles, and various other fields due to being light-weight, have relatively high strength, retain good ductility at sub-zero temperatures, have high corrosion resistance, and are non-toxic. Three-dimensional printing was used for the fabrication of aluminum alloys and aluminum metal matrix composites with high precision, shorter lead time, cost-effectiveness compared to traditional manufacturing. In the 3D printing process, Al-Si alloys and composites were produced by using powder-based manufacturing techniques, such as Selective Laser Melting (SLM), Laser Powder Bed Fusion (LPBF), and Direct Metal Laser Sintering (DMLS) due to their higher laser absorption. The mechanical properties of built parts were improved compared to the traditional manufacturing process and some drawbacks in surface finishing, dimensional accuracy. The mechanical and tribological properties of 3D printing Al-Si alloys were dependent upon process and process parameters. Pre and post-processing methods were used to improve the mechanical and tribological properties. In this paper, an attempt has been made to review the mechanical and tribological properties of 3D printing Al-Si alloys and their composites in various additive manufacturing processes with varying process parameters and to review the effect of pre and post-processing methods on mechanical and tribological properties of 3D printing Al-Si alloys and their composites before and after pre and post-processing methods. The mechanical properties of Al-Si alloys produced in 3D printing methods were more compared to the conventional manufacturing methods. The ductility of the 3D printed Al-Si alloys were improved in heat treatment methods, such as hot isostatic pressing, annealing, and solution heat treatment methods. The 3D printing methods were successfully used for manufacturing Al-Si metal matrix components. The wear resistance of the 3D printed Al-Si metal matrix components were more compared to the conventional manufacturing Al-Si metal matrix components.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Data Availability
This article is a review article. All Reference papers are available.
References
Hull, C.W., Apparatus for production of three-dimensional objects by stereo lithography. Google Patents, (1986)
C. Brecher, Integrative Production stechnikfürHochlohnländer, Springer, (20011) 1781
Emmelmann C, Kranz J, Herzog D, Wycisk E (2014) Laser additive manufacturing of metals. In: Schmidt V, Belegratis MR (eds) Latest technology in biomimetics. Springer, Heidelberg, pp 143–162
Zhang S, Wei QS, Cheng LY, Li S, Shi YS (2014) Effects of scan line spacing on pore characteristics and mechanical properties of porous Ti6Al4V implants fabricated by selective laser melting. Mater Des 63:185–193
Atzeni E, Salmi A (2012) Economics of additive manufacturing for end-usable metal parts. Int J Adv Manuf Technol 62(2012):1147–1155
Chen F, Wu J-M, Wu H-Q, Chen Y, Li C-H, Shi Y-S (2018) Microstructure and mechanical properties of 3Y-TZP dental ceramics fabricated by selective lasersintering combined with cold isostatic pressing. Int J Lightweight Mater Manuf 1:239–245
Qiu Z, Yao C, Feng K, Li Z, Chu PK (2018) Cryogenic deformation mechanism of CrMnFeCoNi high-entropy alloy fabricated by laser additive manufacturing process. Int J Lightweight Mater Manuf 1:33–39
Ma Z, Lin J, Xu X, Ma Z, Tang L, Sun C, Li D, Liu C, Zhong Y, Wang L (2019) Design and 3D printing of adjustable modulus porous structures for customized diabetic foot insoles. Int J Lightweight Mater Manuf 2(1):57–63
K.A. Al-Ghamdi, Sustainable FDM additive manufacturing of ABS components with emphasis on energy minimized and time efficient lightweight construction, Int. J. Lightweight Mater. Manuf. .2(4) (2019) 338-345
Atzeni E, Iuliano L, MInetola P, Salmi A (2010) Redesign and cost estimation of rapid manufactured plastic parts. Rapid Prototyp J 16(5):308–317
Atzeni E, Salmi A (2012) Economics of additive manufacturing for end-usable metal parts. Int J Adv Manuf Technol 62(9-12):1147–1155
Mellor S, Hao L, Zhang D (2014) Additive manufacturing: A framework for implementation. Int J Prod Econ 149:194–201
D. Herzog, V. Seyda, E. Wycisk, C. Emmelmann, additive manufacturing of metals, Acta Mater. 117 (2016) 371–392
Tolosa I, Garciandía F, Zubiri F (2010) Study of mechanical properties of AISI 316 stainless steel processed by "selective laser melting", following different manufacturing strategies. Int J Adv Manuf Technol 51(5–9):639–647
K. Guan, Z. Wang, M. Gao, X. Li, X. Zeng, Effects of processing parameters on tensile properties of selective laser melted 304 stainless steel, Mater. Des. 50 (2013)581–586.
Vrancken B, Thijs L, Kruth J-P, Van Humbeeck J (2012) Heat treatment of Ti6Al4V produced by Selective Laser Melting: microstructure and mechanical properties. JAlloy Compd 541(15):177–185
X. Gong, T. Anderson, K. Chou, A study of the microstructural evolution during selective laser melting of Ti-6Al-4V, Acta materialia.58(9) (2010) 3303-3312
Jia Q, Gu D (2014) Selective laser melting additive manufacturing of Inconel 718 super alloy parts: densification, microstructure and properties. J Alloys Compd 585:713–721
Kanagarajah P, Brenne F, Niendorf T, Maier H (2013) Inconel 939 processed by selective laser melting: Effect of microstructure and temperature on the mechanical properties under static and cyclic loading. Mater Sci Eng A 588:188–195
Kumar S, Pityana S (2011) Laser-based additive manufacturing of metals. Adv Mater Res 227:92–95
Kumar S. Selective Laser Sintering: Recent Advances. In: 4th Pacific International Conference on Applications of Lasers and Optics. Wuhan-China, 617(2010).
Khan M, Dickens PM (2008) Processing parameters for Selective Laser Melting (SLM) of gold. In: Proceedings of Solid Freeform Fabrication symposium:278–279
Louvis E, Fox P, Sutcliffe C (2011) Selective laser melting of aluminum components. J Mater Process Technol 211(2):275–284
Thijs L, Kempen K, Kruth J-P, Humbeeck JV (2013) Fine-structured aluminum products with controllable texture by selective laser melting of pre-alloyed AlSi10Mgpowder. Acta Mater 61:1809–1819
Aboulkhair NT, Everitt N, Ashcroft I, Tuck C (2014) Reducing porosity in AlSi10Mg parts processed by selective laser melting. Addit Manuf 1:77–86
Kumar S, Kruth JP (2010) Composites by rapid prototyping technology. Mater Des 31(2):850–856
Ghosh SK, Saha P, Kishore S (2010) Influence of size and volume fraction of SiC particulates on properties of ex situ reinforced Al-4.5Cu-3Mg metal matrix composite prepared by direct metal laser sintering process. Mater. Sci. Eng. A 527(18–19):4694–4701
Vaezi M, Chianrabutra S, Mellor B, Yang S (2013) Multiple material additive manufacturing, Part1: a review. Virtual and Phys Prototype 8:19–50
Herderick E (2015) Progress in additive manufacturing. J Mater 67:580–581
V. Matilainen, H. Piili, A. Salminen, T. Syvänen, O. Nyrhilä, Characterization of Process Efficiency Improvement in Laser Additive Manufacturing, Phys Procedia 56(0) (2014) 317-326.
B.P. Conner, G.P. Manogharan, A.N. Martof, L.M. Rodomsky, C.M. Rodomsky, D.C. Jordan,J.W. Limperos, Making sense of 3-D printing: Creating a map of additive manufacturing products andservices, Additive Manufacturing 1–4(0) (2014) 64-76
Wang X, Xu S, Zhou S, Xu W, Leary M, Choong P, Qian M, Brandt M, Xie Y (2016) Topological design and additive manufacturing of porous metals for bone scaffolds and orthopedic implants: a review. Biomaterials 83:127–141
Murr LE (2016) Frontiers of 3D printing/additive manufacturing: from human organs to aircraft fabrication. J Mater Sci Technol 32:987–995
Sing S, An J, Yeong W, Wiria F (2016) Laser and electron-beam powder-bed additive manufacturing of metallic implants: a review on processes, materials and designs. JOrthop Res 34(3):369–385
Yap C, Chua C, Dong Z, Liu Z, Zhang D, Loh L, Sing S (2015) Review of selective laser melting: materials and applications. Appl Phys Rev 2(4):041101
Tofail S, Koumoulos E, Bandyopadhyay A, Bose S, O’Donoghue L, Charitidis C (2018) Additive manufacturing: scientific and technological challenges, market uptake and opportunities. Mater Today 21(1):22–37
Atzeni E, Salmi A (2012) Economics of additive manufacturing for end-usable metal parts. Int J Adv Manuf Technol 62(9–12):1147–1155
Schwab K (2017) The Fourth Industrial Revolution. Crown Business, New York, NY, USA
Wohlers Associates Inc, Wohlers report—3D printing and additive manufacturing state of the industry, in: Annual Worldwide Progress Report2016, Wohlers Associates Inc., Fort Collins, Colorado, 2016
R. L. Deuis; C. Subramanian” & J. M. Yellupb, Dry sliding Wear of Aluminium Composites-A Review,Composite and science and technology.57(4)(1997)415-435
Kempen K, Thijs L, Humbeeck JV, Kruth JP (2015) Processing AlSi10Mg by selective laser melting: parameter optimization and material characterization. Mater Sci Technol 31:917–923
Martin JH, Yahata BD, Hundley JM, Mayer JA, Schaedler TA, Pollock TM (2017) 3D printing of high-strengthaluminium alloys. Nature. 549:365–369
Jung JG, Ahn TY, Cho YH, Kim SH, Lee JM (2018) Synergistic effect of ultrasonic melt treatment and fast cooling on the refinement of primary Si in a hypereutectic Al–Si alloy. Acta Mater 144:31–40
Jung JG, Lee SH, Cho YH, Yoon WH, Ahn TY, Ahn YS, Lee JM (2017) Effect of transition elements on the microstructure and tensile properties of Al–12Si alloy cast under ultrasonic melt treatment. J Alloys Compd 712:277–287
Reddappa H. N, Suresh K. R, Niranjan H. B, Satyanarayana K. G, Dry sliding friction and wear behavior of Aluminium/Beryl composites, International Journal of Applied Reseach,Dindigul,2(2) (2011 )502-511.
Cáceres CH, Davidson CJ, Griffiths JR (1995) The deformation and fracture behavior of an Al-Si- Mg casting alloy. Mater Sci Eng A 197(1995):171–179
Kruth JP et al (2007) Consolidation phenomena in laser and powder-bed based layered manufacturing. CIRP Ann Manuf Technol 56(2):730–759
Kruth, J.P., et al.: Benchmarking of different SLS/SLM processes as rapid manufacturing techniques. In: International Conference on Polymers and Moulds Innovations (PMI), Gent, Belgium.(2005)1-7
Sercombe TB, Li X (2016) Selective laser melting of aluminium and aluminium metal matrix composites: review. Mater Technol 31(2):77–85
Mukherjee T, Wei HL, De A, DebRoy T (2018) Heat and fluid flow in additive manufacturing – Part II: Powder bed fusion of stainless steel, and titanium, nickel and aluminum base alloys. Comput Mater Sci 150:369–380
Dong-GyuAhn, Direct Metal Additive Manufacturing Processes and Their Sustainable Applications for Green Technology: A Review, international journal of precision engineering and manufacturing-green technology. 3 (2016)381-395
F. R. Kaschel, M. Celikin, D.P. Dowling,Effects of laser power on geometry, microstructure and echanical properties of printed Ti-6Al-4V parts, Journal of Materials Processing Technology.(278)(2020) 116539
Wang L, Dong C, Kong D, Man C, Liang J, Wang C, Li X (2019) The Effect of Manufacturing Parameters on the Mechanical and Corrosion Behavior of Selective Laser Melted 15-5PH Stainless Steel. Steel Research International 1900447
Hahn Choo, Kin-Ling Sham, John Bohling, Austin Ngo, Xianghui Xiao, Yang Ren, Philip J. Depond, Manyalibo J. Matthews, Elena Garlea,Effect of laser power on defect, texture, and microstructure of a laser powder bed fusion processed 316L stainless steel, Materials& Design.164(2019)107534
Reza Esmaeilizadeh, Ali Keshavarzkermani, Usman Ali, Behzad Behravesh, Ali Bonakdar, Hamid Jahed, Ehsan Toyserkani, On the effect of laser powder-bed fusion process parameters on quasi-static and fatigue behaviour of Hastelloy X: A microstructure/defect interaction study, Additive Manufacturing.38(2021) 101805
Pan Lu, Zhang Cheng-Lin, Wang Liang, Liu Tongand Li Xiao-Cheng, Research on mechanical properties and microstructure by selective laser melting of 316L stainless steel, Materials Research Express.6(12) (2019) 1265h7
AbanLarimian, Manigandan Kannan, Dariusz Grzesiak, Bandar AlMangour, Tushar Borkar,Effect of energy density and scanning strategy on densification, microstructure and mechanical properties of 316L stainless steel processed via selective laser melting, Materials Science and Engineering: A.770(2020)138455
Ilyas Hacısalihoğlu, FatihYıldiz, AyhanÇelik,The effects of build orientation and hatch spacing on mechanical properties of medical Ti–6Al–4V alloy manufactured by selective laser melting, Materials Science and Engineering: A .802(2021) 140649
Alexander Leicht, Camille Pauzon, Masoud Rashidi, Uta Klement, Lars Nyborg, Eduard Hryha,Effect of part thickness on the microstructure and tensile properties of 316L parts produced by laser powder bed fusion, Advances in Industrial and Manufacturing Engineering,.2(2021)100037
Gan L, Cheng Guo, Wenfeng Guo, Hongxing Lu, LinjuWen,Xiaogang Hu and Qiang Zhu, Influence of Selective Laser Melting Process Parameters on Densification Behavior, Surface Quality and Hardness of 18Ni300 Steel, Key Engineering Materials,861(2020) 77-82
Bhishek Mehta, Le Zhou, Thinh Huynh, Sharon Park, Holden Hyer, Shutao Song, Yuanli Bai, D. Devin Imholte, Nicolas E. Woolstenhulme, Daniel M. Wachs, YonghoSohn,Additive manufacturing and mechanical properties of the dense and crack free Zr-modified aluminum alloy 6061 fabricated by the laser-powder bed fusion, Additive Manufacturing..41 (2021) 101966
Zhiheng Hu, Yang Qi, Shubo Gao, XiaojiaNie, Hu Zhang, Haihong Zhu, XiaoyanZeng,Aging responses of an Al-Cu alloy fabricated by selective laser melting, Additive Manufacturing37 (2021) 101635
Cerri E, Ghio E, Bolelli G (2021) Effect of the Distance from Build Platform and Post-Heat Treatment of AlSi10Mg Alloy Manufactured by Single- and Multi-Laser Selective Laser Melting. J of MateriEng and Perform
Peidong He, Hui Kong, Qian Liu, Michael Ferry, Jamie J. Kruzic, XiaopengLi,Elevated temperature mechanical properties of TiCN reinforced AlSi10Mg fabricated by laser powder bed fusion additive manufacturing, Materials Science and Engineering: A.811(2021) 141025
Anton S. Konopatsky, Dmitry G. Kvashnin, Shakti Corthay, Ivan Boyarintsev, Konstantin L. Firestein, Anton Orekhov, Natalya Arkharova, Dmitry V. Golberg, Dmitry V. Shtansky,Microstructure evolution during AlSi10Mg molten alloy/BN microflake interactions in metal matrix composites obtained through 3D printing, Journal of Alloys and Compounds,Volume .859 (2021) 157765
Pelevin IA, Nalivaiko AY, Ozherelkov DY, Shinkaryov AS, Chernyshikhin SV, Arnautov AN, Zmanovsky SV, Gromov AA (2021) Selective Laser Melting of Al-Based Matrix Composites with Al2O3 Reinforcement: Features and Advantages. Materials. 14:2648
Astm, Iso. "ASTM52900-15 standard terminology for additive manufacturing—general principles—terminology." ASTM International, West Conshohocken, PA. 3(4) (2015) 5.
ASTM F2792-12a: Standard Terminology for Additive Manufacturing Technologies,(2012)
Frazier WE (2014) Metal additive manufacturing: A review. J Mater Eng Perform 23:1917–1928
Herzog D, Seyda V, Wycisk E, Emmelmann C (2016) Additive manufacturing of metals. Acta Mater 117:371–392
Sames WJ, List FA, Pannala S, Dehoff RR, Babu SS (2016) The metallurgy and processing science of metal additive manufacturing. Int Mater Rev 61:315–360
Dutta B, Froes FH (2014) Additive manufacturing of titanium alloys. Adv Mater Process 172:18–23
Calignano F, Manfredi D, Ambrosio EP, Iuliano L, Fino P (2013) Influence of process parameters on surface roughness of aluminium parts produced by DMLS. Int J Adv Manuf Technol 67(9–12):2743–2751
G.P. Dinda, A.K. Dasgupta, J. Mazumder, Evolution of microstructure in laser deposited Al-11.28%Si alloy, Surf. Coat. Technol. 206 (2012) 2152–2160,
Dinda GP, Dasgupta AK, Bhattacharya S, Natu H, Dutta B, Mazumder J (2013) Microstructural characterization of laser-deposited Al 4047 alloy. Metall Mater Trans A Phys Metall Mater Sci 44:2233–2242
A. Singh, A. Ramakrishnan, G.P. Dinda, in: Direct laser metal deposition of eutectic Al-Si alloy for automotive applications, TMS 2017 146th Annual Meeting & Exhibition Supplemental Proceedings, 2017
F.A. Espan˜ a, V.K. Balla, A. Bandyopadhyay, Laser processing of bulk Al–12Si alloy: influence of microstructure on thermal properties, Philos. Mag. 91 (2011) 574–588
Yap CY, Chua CK, Dong ZL, Liu ZH, Zhang DQ, Loh LE, Sing SL (2015) Review of selective laser melting: materials and applications. Appl Phys Rev 2:041101
Wohlers T (2014) Wohlers Report : 3D Printing and Additive Manufacturing State of the Industry Annual Worldwide Progress Report. Fort Collins, WohlersAssociatesInc.
Kruth JP, Mercelis P, Froyen L, Rombouts M (2005) Binding mechanisms in selective laser sintering and selective laser melting. Rapid Prototyp J 11:25–36
Olakanmi EO, Cochrane RF, Dalgarno KW (2015) A review on selective laser sintering/ melting (SLS/SLM) of aluminium alloy powders: processing, microstructure, and properties. Prog Mater Sci 74:401–477
Gu DD, Meiners W, Wissenbach K, Poprawe R (2012) Laser additive manufacturing of metallic components: materials, processes and mechanisms. Int Mater Rev 57:133–164
Herzog D, Seyda V, Wycisk E, Emmelmann C (2016) Additive manufacturing of metals. Acta Mater 117:371–392
Aboulkhair NT, Everitt NM, Ashcroft I, et al. Reducing porosity in AlSi10Mg parts processed by selective laser melting. Additive Manufacturing .(1–4) (2014)77–86.
Aboulkhair NT, Maskery I, Tuck C, et al. Improving the fatigue behavior of a selectively laser melted aluminium alloy: influence of heat treatment and surface quality. Mater Des;104(2016) 174–82.
Martin JH, Yahata BD, Hundley JM, et al. 3D printing of high-strength aluminium alloys. Nature .549(7672)(2017)365.
Calignano F. Investigation of the accuracy and roughness in the laser powder bed fusion process. Virtual Phys Prototyping .13(2)(2018)97-104
Sing S, An J, Yeong W et al (2016) Laser and electron-beam powder-bed additive manufacturing of metallic implants: a review on processes, materials and designs. J Orthop Res 34(3):369–385
Yin, H. &Felicelli, S. D. Dendrite growth simulation during solidification in the LENS process. Acta Materialia58(4)( (2010). 1455-1465.
Amano RS, Rohatgi PK (2011) Laser engineered net shaping process for SAE 4140 low alloy steel. Mater Sci Eng A 528(22-23):6680–6693
Bian, L., Thompson, S. M. &Shamsaei, N.. Mechanical Properties and Micro structural Features of Direct Laser-Deposited Ti-6Al-4V.Jom67(3)(2015)629-638.
Gåård, A., Krakhmalev, P., and Bergström, J.. Microstructural characterization and wear behavior of (Fe,Ni)–TiC MMC prepared by DMLS. Journal of Alloys and Compounds, 421, (2016)166–171.
Jhabvala J et al (2010) On the effect of scanning strategies in the Selective Laser Melting process. Virtual and Physical Prototyping 5:99–109
Yasa E et al (2010) Charpy impact testing of metallic Selective Laser Melting parts. Virtual and Physical Prototyping 5:89–98
Bhattacharya S et al (2011) Micro structural evolution and mechanical, and corrosion property evaluation of Cu–30Ni alloy formed by Direct Metal Deposition process. J Alloys Compd 509:6364–6373
Delgado J, Ciurana J, Serenó L (2011) Comparison of forming manufacturing processes and Selective Laser Melting technology based on the mechanical properties of products. Virtual and Physical Prototyping 6:167–178
Yang T, Liu T, Liao W, MacDonald E, Wei H, Chen X, Jiang L (2019) The influence of process parameters on vertical surface roughness of the AlSi10Mg parts fabricated by selective laser melting. J Mater Process Technol 266:26–36
R. Lachmayer, Y. A. Zghair, C. Klose and F. Nürnberger, introducing selective laser melting to manufacture machine elements, international design conference - design .(2016) 831-842
T. G Spears,.A. Gold, In-procress sensing in selective laser melting (SLM) additive manufacturing, Integrating materials and Manufacturing Innovation .5 (2016) 16-40
H. Asgari, C. Baxter, K. Hosseinkhani, M. Mohammadi, On microstructure and mechanical properties of additively manufactured AlSi10Mg 200C usingrecycled powder, Mater. Sci. Eng.: A 707 (2017) 148–158.
E.O. Olakanmi, R.F. Cochrane, K.W. Dalgarno, A review on selective laser sintering/melting (SLS/SLM) of aluminium alloy powders: processing,microstructure, and properties, Prog Mater Sci 74 (2015) 401–477.
Bin Anwar A, Cuong Pham Q (2017) Selective laser melting of AlSi10Mg: effects of scan direction, part placement and inert gas flow velocity on tensile strength. J Mater Process Technol 240:388–396
Trevisan F et al (2017) On the selective laser melting (SLM) of the AlSi10Mg alloy: process, microstructure, and mechanical properties. Materials 10:76
Krishnan M et al (2014) On the effect of process parameters on properties ofAlSi10Mg parts produced by DMLS. Rapid Prototyp J 20:449–458
Kempen K, Thijs L, Van Humbeeck J, Kruth J-P (2015) Processing AlSi10Mg by selective laser melting: parameter optimization and material characterization. Mater Sci Technol 31:917–923
Read N, Wang W, Essa K, Attallah MM (2015) Selective laser melting of AlSi10Mgalloy: process optimization and mechanical properties development. Mater.Des. 65:417–424
Arfan Majeed, Yingfeng Zhang, JingxiangLv, Tao Peng, Zahid Atta, Altaf Ahmed, Investigation of T4 and T6 heat treatment influences on relative density and porosity of AlSi10Mg alloy components manufactured by SLM,Computers& Industrial Engineering.139(2020) 106194 .
Yasa, E., Kruth, J.-P.: Application of laser re-melting on selective laser melting parts. Additive .Prod. Eng. Manag. 6(4) (2011) 259–270
Monroy K, Delgado J, Ciurana J (2013) Study of the pore formation on CoCrMo alloys by selective laser melting manufacturing process. Procedia Eng 63:361–369
Louvis E, Fox P, Sutcliffe CJ (2011) Selective laser melting of aluminium components. Journal ofMaterials Processing Technology 211:275–284
K. Kempen, L. Thijs, E. Yasa, M. Badrossamay, W; Verheecke, J.P. Kruth, Process optimization and micro structural analysis for selective laser melting of AlSi10Mg, International Solid Freeform fabrication Symposium 22 (2011) 484-449
Quintino L, Miranda R, Dilthey U, Iordachescu D, Banasik M, Stano S (2012) Laser Welding of Structural Aluminium. Adv Struct Mater 8:33–57
Arata Y, Miyamoto I (1972) Some fundamental properties of high power laser beam as a heat source (report 2) – CO2 laser absorption characteristics of metal. Transactions of the Japan Welding Society 3:152–162
ASM specialty handbook, Aluminium and aluminium alloys, sixth printing, (2007)720
Saket Thapliyal, MageshwariKomarasamy, Shivakant Shukla, Le Zhou, Holden Hyer, Sharon Park, Yongho Sohn, Rajiv S. Mishra, An integrated computational materials engineering-anchored closed-loop method for design of aluminum alloys for additive manufacturing, Materialia,9(2020)100574.
Kumar S (2014) Selective laser sintering/melting. In: Hashmi S (ed) Comprehensive Materials Processing. Elsevier, Amsterdam, pp 93–133
Emmelmann C, Sander P, Kranz J, Wysick E (2011) Laser additive manufacturing and bionics. Phys Procedia 12:364–368
Gibson I, Rosen DW, Stucker B (2015) Additive Manufacturing Technologies, Rapid Prototyping to Direct Digital Manufacturing. Springer, Verlag, New York 2015
Ardila, L.C., Garciandia, F., González-Díaz, J.B., Álvarez, P., Echeverria, A., Petite,M.M., Deffley, R., Ochoaa, J.,. Effect of IN718 recycled powder reuse on properties of parts manufactured by means of selective laser melting. Phys Procedia 56 (2014) 99–107.
Lishi Jiao , Zhong Yang Chua , Seung Ki Moon , Jie Song , Guijun Bi and Hongyu Zheng, Femtosecond Laser Produced Hydrophobic Hierarchical Structures on Additive Manufacturing Parts, Nonmaterial’s.8(8)(2018)601
Khaing MW, Fuh JYH, Lu L (2001) Direct Metal Laser Sintering for rapid tooling: Processing andcharacterization of EOS parts. J Mater Process Technol 113:269–272
Wohlers, T. T. and Caffrey, T., Wohlers Report : 3D Printing and Additive Manufacturing State of the Industry Annual Worldwide Progress Report,” Wohlers Associates.(2015).
Kruth, J. P., Mercelis, P., Froyen, L., and Rombouts, M., Binding Mechanisms in Selective Laser Sintering and Selective Laser Melting.11(1)(2005)26-36
Aboulkhair NT, Maskery I, Tuck C, Ashcroft I, Everitt NM (2016) The microstructure and mechanical properties of selectively laser melted AlSi10Mg: the effect of a conventional T6-like heat treatment. Mater Sci Eng A 66:139–146
Wohlers, T. T. and Caffrey, T., Wohlers Report : 3D Printing and Additive Manufacturing State of the Industry Annual Worldwide Progress Report,” Wohlers Associates.(2015).
Strano G, Hao L, Everson RM, Evans KE (2013) Surface roughness analysis, modeling and prediction in selective laser melting. J Mater Process Technol 213(4):589–597
Atzeni, E., Salmi, A., Incontro, M., A DoE approach for evaluating the quality of self supporting faces in DMLS, in 4th International Conference on Additive Technologies (iCAT 2012).(2012)
Calignano F, Manfredi D, Ambrosio EP, Iuliano L, Fino P (2013) Influence of process parameters on surface roughness of aluminum parts produced by DMLS. Int J Adv Manuf Technol 67:2743–2751
Herzog D, Seyda V, Wycisk E, Emmelmann C (2016) Additive manufacturing of metals. Acta Mater 117(2016):371–392
Lewandowski JJ, Seifi M (2016). Annu Rev Mater Res 46:151–186
Everton SK, Hirsch M, Stravroulakis P, Leach RK, Clare AT (2016) Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing. Mater Des 95:431–445
DebRoy T, Wei HL, Zuback JS, Mukherjee T, Elmer JW, Milewski JO, Beese AM, Wilson-Heid A, De A, Zhang W (2018) Additive manufacturing of metallic components – Process, structure and properties. Prog Mater Sci 92:112–224
Tapia, G.; Elwany, A. A review on process monitoring and control in metal-based additive manufacturing’s. Manuf. Sci. E .136(2014) 060801.
Mower, T.M.; Long, M.J. Mechanical behavior of additive manufactured, powder-bed laser-fused materials. Mater. Sci. Eng. A .651(2016) 198–213
Kimura T, Nakamoto T (2017) Thermal and mechanical properties of commercial-purity aluminium fabricated using selective laser melting. Mater Trans 58:799–805
Herzog D, Seyda V, Wycisk E, Emmelmann C (2016) Additive manufacturingof metals. Acta Mater 157:371–392
Wohlers Report, Additive Manufacturing and 3D Printing State on the industry, Wohlers Associates, Fort Collins, Colorado, ICED15.12(2013)
Petroušek P, Bidulská J, Bidulský R, Kocisko R, Fedorikova A, Hudak R, Rajtukova V, Zivcak J (2017) Mechanical properties and porosity of Ti-6Al-4V alloy prepared by AM technology. MM Science Journal:1752–1755
AlicaFedorikova, Radovan Hudak,,Jozefzivcak, Robert bidulsky, PatrikPetrousek, Jana Bidulska1,Robert Kocisko1,Viktoria Rajtukova, Mechanical properties of powder cocrw-alloy prepared by am technology. ,MM Science Journal, (2016)1586-1589
Hamidi Nasab M, Gastaldi D, Lecis NF, Vedani M (2018) On morphological surface features of the parts printed by selective laser melting (SLM). Addit Manuf 24:373–377
Yadroitsev I, Smurov I (2011) Surface morphology in selective laser melting of metal powders, in: Physics. Procedia.
Townsend A, Senin N, Blunt L, Leach RK, Taylor JS (2016) Surface texture metrology for metal additive manufacturing: a review. Precis Eng 46:34–47
J.S. Taylor, Physical processes linking input parameters and surface morphology in additivemanufacturing, in: Proc. - ASPE 2015 Spring Top. Meet. Achiev. Precis. Toler.Addit. Manuf.(2015) 70-71.
L. zhi Wang, S. Wang, J. jiao Wu, Experimental investigation on densification behavior and surface roughness of AlSi10Mg powders produced by selective laser melting, Opt. Laser Technol. 96 (2017) 88–96.
Mumtaz K, Hopkinson N (2009) Top surface and side roughness of Inconel 625 parts processed using selective laser melting. Rapid Prototyp J 15:96–103
Strano G, Hao L, Everson RM, Evans KE (2013) Surface roughness analysis, modeling and prediction in selective laser melting. J Mater Process Technol 213:589–597
J.C. Fox, S.P. Moylan, B.M. Lane, Effect of Process Parameters on the Surface Roughness of Overhanging Structures in Laser Powder Bed Fusion Additive Manufacturing, in: Procedia.45(2016)131-134
Manfredi D et al (2014) Additive manufacturing of Al alloys and Aluminium Matrix Composites (AMCs), in: Light Metal Alloys Applications, edited by W. A Monteiro
Kruth JP, Mercelis P, Van Vaerenbergh J, Froyen L, Rombouts M (2005) Binding mechanisms in selective laser sintering and selective laser melting. Rapid Prototyp J 11:26–36
Niu HJ, Chang ITH (2000) Selective laser sintering of gas atomized M2 high speed steel powder. J Mater Sci 35:31–38
Manfredi D et al (2013) From powders to dense metal parts: characterization of commercial AlSiMg alloy processed through direct metal laser sintering. Materials 6:856–869
Buchbinder D, Schleifenbaum H, Heidrich S, Meiners W, Bültmann J (2011) High power Selective Laser Melting (HP SLM) of aluminum parts. Phys Procedia 12:271–280
Read N, Wang W, Essa K, Attallah MM. Selective laser melting of AlSi10Mg alloy: process optimization and mechanical properties development. Mater Des .65(2015)417-424.
Zhang J, Song B, Wei Q, Bourell D, Shi Y (2019) A review of selective laser melting of aluminium alloys: processing, microstructure, property and developing trends. J Mater Sci Technol 35:270e284
R. Li, M. Wang, T. Yuan, B. Song, C. Chen, K. Zhou, P. Cao, Selective laser melting of a novel Sc and Zr modified Al-6.2 Mg alloy: processing, microstructure, and properties, Powder Technol. 319 (2017) 117e128.
Wang M, Song B, Wei Q, Zhang Y, Shi Y (2019) Effects of annealing on the microstructure and mechanical properties of selective laser melted AlSi7Mg alloy. Mater Sci Eng A 739:463e472
R. Li, M. Wang, T. Yuan, B. Song, C. Chen, K. Zhou, P. Cao, Selective laser melting of a novel Sc and Zr modified Al-6.2 Mg alloy: Processing ,microstructure, and properties, Powder Technol. 319 (2017) 117-128.
Rao H, Giet S, Yang K, Wu X, Davies CHJ (2016) The influence of processing parameters on aluminium alloy A357 manufactured by Selective Laser Melting. Mater Des 109:334–346
Bartkowiak K, Ullrich S, Frick T, Schmidt M (2011) New Developments of Laser Processing Aluminium Alloys via Additive Manufacturing Technique. Phys Procedia 12:393–401
Buchbinder D, Schleifenbaum H, Heidrich S, Meiners W, Bültmann J (2011) High power selective laser melting (HP SLM) of aluminum parts. Phys Procedia 12:271–278
Li Y, Gu D (2014) Parametric analysis of thermal behavior during selective laser melting additive manufacturing of aluminum alloy powder. Mater Des 63:856–867
H. Zhang, H. Zhu, X Nie, J Yin, Z Hu, X Zeng, Effect of Zirconium addition on crack, microstructure and mechanical behavior of selective laser melted Al-Cu-Mg alloy, Script Materialia134 (2017) 6-10
Aboulkhair NT, Maskery I, Tuck C, Ashcroft I, Everitt NM (2016) On the formation of AlSi10Mg single tracks and layers in selective laser melting: Microstructure and nano-mechanical properties. J Mater Process Technol 230:88–98
Louvis E, Fox P, Sutcliffe CJ (2011) Selective laser melting of aluminium components. J Process Technol 211:275–284
Loto CA (2016) Electroless nickel plating – a review. Silicon. 8:177–186
Tolochko NK, Laoui T, Khlopkov YV, Mozzharov SE, Titov VI, Ignatiev MB (2000) Absorptance of powder materials suitable for laser sintering. Rapid Prototyp J 6:155–160
Fischer P, Romano V, Weber HP, Karapatis NP, Boillat E, Glardon R (2003) Sintering of commercially pure titanium powder with a Nd:YAG laser source. Acta Mater 51:1651–1662
Lekatou AG, Sfikas AK, Karantzalis AE (2017) The influence of the fabrication route on the microstructure and surface degradation properties of Al reinforced by Al9Co2. Mater Chem Phys 200:33–49
Huber F, Papke T, Scheitler C, Hanrieder L, Merklein M, Schmidt M (2018) In situ Formation of a Meta stable β-Ti Alloy by Laser Powder Bed Fusion(L-PBF) of Vanadium and Iron Modified Ti-6Al-4V. Metals. 8:1067
Zhou W, Dong M, Zhou Z, Sun X, Kikuchi K, Nomura N, Kawasaki A (2019) In situ formation of uniformly dispersed Al4C3 nano rods during additive manufacturing of grapheme oxide/Al mixed powders. Carbon. 141:67–75
Zhou W, Sun X, Kikuchi K, Nomura N, Yoshimi K, Kawasaki A (2018) In situ synthesized Tic/Mo-based composites via laser powder bed fusion. Mater Des 146:116–124
Yadroitsev I, Krakhmalev P, Yadroitsava I (2017) Titanium alloys manufactured by in situ alloying during laser powder bed fusion. JOM. 69:2725–2730
Geng K, Yang Y, Li S, Misra RDK, Zhu Q, Enabling high-performance 3D printing of Al powder by decorating with high laser absorbing Co phase, Additive Manufacturing .32(2020)101012
Galy C, Le Guen E, Lacoste E, Arvieu C (2018) Main defects observed in aluminum alloy parts produced by SLM: from causes to consequences. Additive Manufacturing 22:165–175
Wong M, Tsopanos S, Sutcliffe CJ, Owen I (2017) Selective laser melting of heat transfer devices. Rapid Prototyp J 13:291–297
Takahiro. Kimura, Takayuki Nakamoto, Masataka Mizuno and Hideki Araki, “Effect of silicon content on densification, mechanical and thermal properties of Al-xSi binary alloys fabricated using selective laser meltin, Materials Science & Engineering A.682(13) (2017)593-602
Osório WR, Goulart PR, Garcia A (2008) Effect of silicon content on microstructure and electrochemical behavior of hypoeutectic Al-Si alloys. Mater Lett 62(2008):365–369
Ponnusamy MSH, Ruan D, Palanisamy S, Rahman RA, Kariem RMA (2018) High strain rate behaviour at high temperature of AlSi12 parts produced by selective laser melting. IOP Conf. Series: Materials Science Eng 377:012167
Rashid R, Masood SH, Ruan D, Palanisamy S, Rahman Rashid RA, Elambasseril J, Brandt M (2018) Effect of energy per layer on the anisotropy of selective laser melted AlSi12 aluminium alloy. Additive Manufacturing 22:426–439
Vora P, Mumtaz K, Todd I, Hopkinson N (2015) AlSi12 in-situ alloy formation and residual stress reduction using anchorless selective laser melting. Additive Manufacturing 9:7–12
Wang X, Zhang L, Fang M, Sercombe TB (2014) The effect of atmosphere on the structure and properties of a selective laser melted Al–12Si alloy. Mat Sci and Engg: A 597(12):370–375
Siddique S, Imran M, Wycisk E, Emmelmann C, Walther F (2015) Influence of process-induced microstructure and imperfections on mechanical properties of AlSi12 processed by selective laser melting. J Mat Processing Tech 221:205–213
Siddique S, Imran M, Walther F (2017) Very high cycle fatigue and fatigue crack propagation behavior of selective laser melted AlSi12 alloy. Int J Fatigue 94:246–254
Prashanth K, Scudino S, Klauss H, Surreddi KB, Löber L, Wang Z, Chaubey A, Kühn U, Eckert J (2014) Microstructure and mechanical properties of Al–12Si produced by selective laser melting: Effect of heat treatment. Mat Sci Engg: A 590:153–160
Li X, Wang X, Saunders M, Suvorova A, Zhang L, Liu Y, Fang M, Huang Z, Sercombe TB (2015) A selective laser melting and solution heat treatment refined Al–12Si alloy with a controllable ultrafine eutectic microstructure and 25% tensile ductility. Acta Mater 95:74–82
Fefelov AS, Merkushev AG, Chikova OA (2017) Microstructure and mechanical properties of Al-12Si produced by selective laser melting. IOP Conf Series: Earth and Environmental Science 87:092011
Jyoti S, Prashanth KG, Scudino S, Eckert J, Prakash O, Ramamurty U (2016) Simultaneous enhancements of strength and toughness in an Al-12Si alloy synthesized using selective laser melting. Acta Mater 115:285–e294
Louvis E, Fox P, Sutcliffe CJ (2011) Selective laser melting of aluminium components. J Mater Process Technol 211:275–284
Olakanmi EO, Cochrane RF, Dalgarno KW (2011) Densification mechanism and microstructural evolution in selective laser sintering of Al–12Si powders. J Mater Process Technol 217:113–121
Li XP, O’Donnell KM, Sercombe TB (2016) Selective laser melting of Al-12Si alloy: Enhanced densification viapowder drying. Additive Manufacturing 10:10–14
Kang N, Coddet P, Linliao H, Baur T, Coddet C (2016) Wear behavior and microstructure of hypereutectic Al-Si alloys prepared by Selective laser melting. Appl Surf Sci 378:142–149
Siddique S, Imran M, Rauer M, Kaloudis M, Wycisk E (2015) Computed tomography for characterization of fatigue performance of selective laser melted parts. Mater Des 83:661–669
Prashanth KG, Scudino S, Eckert J (2016) Tensile properties of Al-12Si fabricated via selective laser melting (SLM) at different temperatures. Technologies 4(4):38
Pan M, Prashanth KG, Scudino S, Jia Y, Wang H, Zou C, Wei Z, Eckert J (2014) Influence of annealing on mechanical properties of Al-20Si processed by selective laser melting. Metal 4:28–36
Dörfert R, Stoll C, Freiße H, Seefeld T, Vollertsen F (2017) Influence of the process on surface roughness of 3D-printed aluminum alloy AlSi40 parts. International Journal of Latest Research in Engineering and Technology 3(10):35–41
Mueller M, Riede M, Eberle S, Reutlinger A, Brandão AD, Pambaguian L, Seidel A, López E, Brueckner F, Beyer E, Leyens C (2019) Micro structural, mechanical, and thermo-physical characterization of hypereutectic AlSi40 fabricated by selective laser melting. J Laser Appl 31:022321
Hanemann T, Carter LN, Habschied M, Adkins NJE, Attallah MM, Heilmaier M (2019) In-situ alloying of AlSi10MgþSi using Selective Laser Melting to control the coefficient of thermal expansion. J Alloys Compd 795:8e18
ASM Handbook (1990) Volume 2, Properties and Selection: Non ferrous Alloys and Special-Purpose Materials, ASM International, Materials Park, OH
González R, González A, Talamantes-Silva J, Valtierra S, Mercado-Solís RD, Garza-Montes-de-Oca NF, Colás R (2013) Fatigue of an aluminium cast alloy used in the manufacture of automotive engine blocks. Int J Fatigue 54(0):118–126
Zebala W, Kowalczyk R, Matras A (2015) Analysis and optimization of sintered carbides turning with PCD tools. Procedia Eng 100:283–290
Read N, Wang W, Essa K, Attallah MM (2015) Selective laser melting of AlSi10Mg alloy: Process optimisation and mechanical properties development. Mater Des 65:417–424
Godino Martinez M (2013) AlSi10Mg parts produced by selective laser melting (SLM) (masters). Universidad Carlos III de Madrid
Santos MC, Machado AR, Sales WF, Barrozo M, Ezugwu EO (2016) Machining of aluminium: a review. Int J Adv Manuf Technol 86:3067–3080
Buchbinder D, Schleifenbaum H, Heidrich S, Meiners W, Bültmann J (2011) High power Selective Laser Melting (HP SLM) of aluminum parts. Phys Procedia 12:271–280
Kempen K, Thijs L, Van Humbeek J, Kruth J-P (2012) Mechanical properties of AlSi10Mg produced by selective laser melting. Phys Procedia 39:439–446
Hitzler L, Janousch C, Schanz J, Merkel M, Heine B, Mack F et al (2017) Direction and location dependency of selective laser melted AlSi10Mg specimens. J Mater Process Technol 243:48–61
Brandl E, Heckenberger U, Holzinger V, Buchbinder D (2012) Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): microstructure, high cycle fatigue, and fracture behaviour. Mater Des 34:159–169
Maskery I, Aboulkhair NT, Tuck C, Wildman RD, Ashcroft IA, Everitt NM, et al. .(2015) Fatigue performance enhancement of selectively laser melted aluminium alloy byheat treatment. In: Twenty-sixth annual international solid freeform fabrication (SFF) symposium – an additive manufacturing conference, Texas, U.S.A. 1017-1026
Tang M, Chris PP (2017) Oxides, porosity and fatigue performance of AlSi10Mg parts produced by selective laser melting. Int J Fatigue 94:194–201
Aboulkhair NT, Maskery I, Tuck C, Ashcroft I, Everitt NM (2016) Improving the fatigue behaviour of a selectively laser melted aluminium alloy: influence of heat treatment and surface quality. Mater Des 104:174–182
Mower TM, Long MJ (2016) Mechanical behavior of additive manufactured, powder-bed laser-fused materials. Mater Sci Eng A 651:198–213
Olakanmi EO, Cochrane RF, Dalgarno KW (2015) A review on selective laser sintering/ melting (SLS/SLM) of aluminium alloy powders: processing, microstructure, and properties. Prog Mater Sci 74:401–477
Gu DD, Meiners W, Wissenbach K, Poprawe R (2012) Laser additive manufacturing of metallic components: materials, processes and mechanisms. Int Mater Rev 57:133–164
Li W, Li S, Liu J, Zhang A, Zhou Y, Wei Q, Yan C, Shi Y (2016) Effect of heat treatment on AlSi10Mg alloy fabricated by selective laser melting: microstructure evolution, mechanical properties and fracture mechanism. Mater Sci Eng A 663:116–125
Rosenthal I, Stern A, Frage N (2017) Strain rate sensitivity and fracture mechanismof AlSi10Mg parts produced by selective laser melting. Mater Sci Eng A 682:509–517
Asgari H, Odeshi A, Hosseinkhani K, Mohammadi M (2018) On dynamicmechanical behavior of additively manufactured AlSi10Mg 200C. Mater Lett 211:187–190
Zhang P, Li Z, Liu B, Ding W, Peng L (2016) Improved tensile properties of a newaluminum alloy for high pressure die casting. Mater Sci Eng A 651:376–390
Read N, Wang W, Essa K, Attallah M (2015) Selective laser melting of AlSi10Mg alloy: process optimisation and mechanical properties development. Mater Des 65:417–424
Krishnan M, Atzeni E, Canali R, Calignano F, Manfredi D, Ambrosio E, Iuliano L (2014) On the effect of process parameters on properties of AlSi10Mg partsproduced by DMLS. Rapid Prototyp J 20(6):449–458
Kempen K, Thijs L, Humbeeck J, Kruth J-P (2015) Processing AlSi10Mg by selective laser melting: parameter optimisation and material characterisation. Mater SciTechnol 31(8):917–923
Rosenthal I, Stern A, Frage N (2017) Strain rate sensitivity and fracture mechanism of AlSi10Mg parts produced by Selective Laser Melting. Mater Sci Eng A 682:509–517
Carter LN, Martin C, Withers PJ et al (2014) The influence of the laser scan strategy on grain structure and cracking behaviour in SLM powder-bed fabricated nickel superalloy. J Alloys Compd 615(2):338–347
Salmi A, Atzeni E (2017) History of residual stresses during the production phases of AlSi10Mg parts processed by powder bed additive manufacturing technology. Virtual Phys Prototyping 12(2):153–160
Zhu Y, Ding Z, Wang L et al (2018) Investigation of performance and residual stress generation of AlSi10Mg processed by selective laser melting. Adv Mater Sci Eng:7814039
Thijs L, Kempen K, Kruth J-P, Humbeeck JV (2013) Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mgpowder. Acta Mater 61:1809–1819
Lu L, Nogita K, Dahle AK (2005) Combining Sr and Na additions in hypoeutectic Al-Si foundry alloys. Mater Sci Eng A 399:244–253
Karakösea E, Keskin M (2009) Effect of solidification rate on the microstructure and microhardness of a melt-spun Al-8Si-1Sb alloy. J Alloys Compd 479:230–236
Sames W, List F, Pannala S, Dehoff R (2016) Metallurgy and processing science of metaladditive manufacturing. Int Mater Rev 61(5):315–360
Weingarten C, Buchbinder D, Pirch N, Meiners W, Wissenbach K, Poprawe R (2015) Formation and reduction of hydrogen porosity during selective laser melting ofAlSi10Mg. J Mater Process Technol 221:112–120
Aboulkhair NT, Everitt NM, Ashcroft I, Tuck C (2014) Reducing porosity inAlSi10Mg parts processed by selective laser melting. Addit Manuf 4:77–86
Weingarten C et al (2015) Formation and reduction of hydrogen porosity duringselective laser melting of AlSi10Mg. J Mater Process Technol 221:112–120
Aboulkhair NT, Everitt NM, Ashcroft I et al (2014) Reducing porosity in AlSi10Mg parts processed by selective laser melting. AdditManuf 1–4:77–86
Plessis AD, Yadroitsev I, Yadroitsava I et al (2018) X-ray microcomputed tomography in additive manufacturing: a review of the current technology and applications. 3D Print AdditManuf 5(3):227–247
Xu Z, Liu A, Wang X (2021) Fatigue performance and crack propagation behavior of selective laser melted AlSi10Mg in 0°, 15°, 45° and 90° building directions. Mater Sci Eng A 812:141141
Brandl E, Heckenberger U, Holzinger V, Buchbinder D (2012) Additivemanufactured AlSi10Mg samples using selective laser melting (SLM):microstructure, high cycle fatigue, and fracture behavior. Mater Des 34:159–169
Tang M, Pistorius PC (2017) Oxides, porosity and fatigue performance of AlSi10Mg parts produced by selective laser melting. Int J Fatigue 94:192–201
Aboulkhair NT, Everitt NM, Ashcroft I, et al., Reducing porosity in AlSi10Mg parts processed by selective laser melting. AdditManuf .1–4 (2014) 77–86.
Brandl E, Heckenberger U, Holzinger V, Buchbinder D. Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): microstructure, high cyclefatigue, and fracture behaviour. Mater Des .34 (2012) 159–69.\
Tang M, Pistorius P Chris. Oxides, porosity and fatigue performance of AlSi10Mg parts produced by selective laser melting. Int J Fatigue 94 (2017) 192–201
A. Barari, H.A. Kishawy, F. Kaji, M.A. Elbestawi, On the surface quality of additive manufactured parts, Int. J. Adv. Manuf. Technol. 89 (2017)1969-1974.
Mohammadi M, Asgari H (2018) Achieving low surface roughness AlSi10Mg_200C parts using direct metal laser sintering. Addit Manuf 20:23–32
Leon A, Aghion E (2017) Effect of surface roughness on corrosion fatigue performance of AlSi10Mg alloy produced by Selective Laser Melting (SLM). Mater Charact 131:229–237
Uzan NE, Shneck R, Yeheskel O (2017) Frage N, Fatigue of AlSi10Mg specimens fabricated byadditive manufacturing selective laser melting (AM-SLM). Mater Sci Eng A 704:229–237
Günther, J., Leuders, S., Koppa, P., Tröster, T., Henkel, S., Biermann, H., Niendorf, T.,2018. On the effect of internal channels and surface roughness on the high-cycle fatigue performance of Ti-6Al-4V processed by SLM. Mater. Des. 143 (2018) 1-11
M. Jamshidinia, F. Kong, R. Kovacevic, The numerical modeling of fatigueproperties of a bio-compatible dental implant produced by electron beammelting (EBM), in: In Proceeding of the Twenty Forth Annual InternationalSolid Freeform Fabrication Symposium.(2013) 791-804
Stephens RI, Fatemi A, Stephens RR, Fuchs HO (2000) Metal Fatigue inEngineering. John Wiley & Sons
Zou Y et al (2017) The intergranular corrosion behavior of 6000-series alloys withdifferent Mg/Si and Cu content. Appl Surf Sci 405:489–496
Li T, Li XG, Dong CF, Cheng YF (2010) Characterization of atmospheric corrosionof 2A12 aluminum alloy in tropical marine environment. J Mater EngPerform 19:591–598
Molland AF, Turnock SR, Hudson DA (2017) Ship Resistance and Propulsion. Cambridge University Press
Wohlers, Wohlers Report 2014 - 3D Printing and Additive Manufacturing State of theIndustry Annual Worldwide Progress Report (2016).
Strano, G., Hao, L., Everson, R.M., Evans, K.E.., Surface roughness analysis, modellingand prediction in selective laser melting. Journal of Materials Processing Technology,.213(4) (2013) 589-597.
Bañón c., Raspall f. Additive Manufacturing Technologies for Architecture. In: 3D Printing Architecture. SpringerBriefs in Architectural Design and Technology. Springer, Singapore.(2021) 13-20.
Tian Y, Tomus D, Rometsch P, Wu X (2017) Influences of processing parameters on surface roughness of Hastelloy X produced by selective laser melting. Addit Manuf 13:103–112
Calignano F, Manfredi D, Ambrosio EP, Iuliano L, Fino P (2013) Influence of processparameters on surface roughness of aluminum parts produced by DMLS. InternationalJournal of Advanced Manufacturing Technology 67(9-12):2743–2751
Gebhardt, A., Hötter, J.-S., Ziebura, D.: Impact of SLM build parameters on the surface quality. RTejournal - Forum für Rapid Technologie .11(2014)
Calignano F et al (2013) Influence of process parameters on surface roughness of aluminum parts produced by DMLS. Int J Adv Manuf Technol 67(9–12):2743–2751
Tian Y, Tomus D, Rometsch P, Wu X (2017) Influences of processing parameters on surface roughness of Hastelloy X produced by selective laser melting. Addit.Manuf. 13:103–112
Nguyen QB, Luu DN, Nai SML, Zhu Z, Chen Z, Wei J (2018) The role of powder layer thickness on the quality of SLM printed parts. Arch Civil Mech Eng 18:948–955
Calignano F (2018) Investigation of the accuracy and roughness in the laser powder bed fusion process. Virtual Phys Prototyp 13:97–104
Atzeni, E., Salmi, A., Incontro, M., Study on unsupported over hangs of AlSi10Mg parts. A DoE approach for evaluating the quality of selfsupporting faces in DMLS, in 4th International Conference on Additive Technologies (iCAT2012), D. International, Editor. 2012: Maribor, Slovenia
P.Ferro, R,meneghello, S.M.J.Razavi,F.Berto, and G.Savio,,Porasity inducing process parameters in selective laser melted AlSi10Mg AlloyPhysical meso mechanics, 23 (2020) 256-262
Ahmed A, Majeed A, Atta Z, Jia G (2019) Dimensional Quality and Distortion Analysis of Thin-Walled Alloy Parts of AlSi10Mg Manufactured by Selective Laser Melting. Journal of Manufacturing and Materials Processing 3(2):5
Xiaochuan Zhang , Jinwu Kang ,*, Yiming Rong , Pengyue Wu and Tao Feng ,” Effect of Scanning Routes on the Stress and Deformation of Overhang Structures Fabricated by SLM, Materials.12(1) (2019) 47
Ahmed H. Maamoun, Yi F. Xue1, Mohamed A. Elbestawi 1, Stephen C. Veldhuis,”Effect of SLM process parameters on the quality of Al Alloy parts; Part I: powder characterization, density, surface roughness, and dimensional 2 accuracy”Peer-reviewed version available at Materials .11(2018)2343
Tao Yang, Tingting Liu, Wenhe Liao, Eric MacDonald, Huiliang Wei, Xiangyuan Chen, LiyiJiang,”The Influence of Process Parameters on Vertical Surface Roughness of the AlSi10Mg Parts Fabricated by Selective Laser Melting”, J Mater Process Technol266 (2019) 26-36
S.A. Jawade , Rashmi.S. Joshi, S.B. Desai,” Comparative study of mechanical properties of additively manufactured aluminum alloy”, Materials Today: Proceedings ,2020.
NaorEladUzana,, Barak Ratzker, Peri Landau, Sergey Kalabukhov, Nachum Frage,” Compressive creep of AlSi10Mg parts produced by selective laser melting additive manufacturing technology, Additive Manufacturing 29 (2019) 100788
.P. Lam, D.Q. Zhang, Z.H. Liu & C.K. Chua (2015): Phase analysis and microstructure characterisation of AlSi10Mg parts produced by Selective Laser Melting, Virtual and Physical Prototyping, virtual and physical prototyping.10(4) (2015) 207-215
Z. Dong, Y. Liu, Q. Zhang, J. Ge, S. Ji, W. Li, J. Liang, “Microstructural heterogeneity of AlSi10Mg alloy lattice structures fabricated by selective laser melting: Phenomena and mechanism”, Journal of Alloys and Compounds .833(2020) 155071.
Hadadzadeh A, Amirkhiz BS, Shakerin S, Kelly J, Li J, Mohammadi M, Microstructural investigation and mechanical behavior of a two-material component fabricated through selective laser melting of AlSi104Mg on an Al-Cu-Ni-Fe-Mg cast alloy substrate, Additive Manufacturing .31 (2020)100937
K. Kamarudin1,, M.S. Wahab, Z. Shayfull, Aqeel Ahmed , and A.A. Raus,” Dimensional Accuracy and Surface Roughness Analysis for AlSi10Mg Produced by Selective Laser Melting (SLM), MATEC Web of Conferences .7(2016) 01077
Ming Tang, P. Chris Pistorius, “Oxides, porosity and fatigue performance of AlSi10Mg parts produced by selective laser melting”, International Journal of Fatigue xxx (2016) .94(2) (2017) 192-201
Ahmad Bin Anwar, Quang-Cuong Pham, “Selective Laser Melting of AlSi10Mg: Effects of scan direction, part placement and inert gas flowvelocity on tensile strength, Journal of Materials Processing Tech.240 (2017) 388-396
A. A Raus1, , M. S. Wahab , Z. Shayfull2 ,K. Kamarudin1 and M. Ibrahim, The Influence of Selective Laser Melting Parameters on Density and Mechanical Properties of AlSi10Mg, MATEC Web of Conferences .78(2016) 01078
K. Kamarudin, M. S. Wahab, A. A. Raus, Aqeel Ahmed, S. Shamsudin, Benchmarking of dimensional accuracy and surface roughness for AlSi10Mg part by selective laser melting (SLM), AIP Conf. Proc.1831 (2017) 020047
Lianfeng Wang, Xiaohui Jiang, Miaoxian Guo, Xiaogang Zhu & Biao Yan (2017): Characterisation of structural properties for AlSi10Mg alloys fabricated by selective laser melting, Materials Science and Technology, materials science and technology.33(18) (2017) 2274-2282
Aqeel Ahmed, M. S. Wahab, A. A. Raus, K. Kamarudin, Qadir Bakhsh and Danish Ali,Effects of Selective Laser Melting Parameters on Relative Density of AlSi10Mg, International Journal of Engineering and Technology (IJET).8(6) (2016) 2552-2557
J. Zou , Y. Zhua, M. Pan , T. Xie , X. Chen , H. Yang, A study on cavitation erosion behavior of AlSi10Mg fabricated by selective laser melting (SLM), Wear376-377(2017)496–506
Wang L-z, Wang S, Wu J-j (2017) Experimental investigation on densification behavior and surface roughness of AlSi10Mg powders produced by selective laser melting. Opt Laser Technol 96:88–96
Naoki Takata, Hirohisa Kodaira1, Asuka Suzuki, Makoto Kobashi, Size dependence of microstructure of AlSi10Mg alloy fabricated by selective laser melting, Materials Characterization.143 (2018) 18-26
Awd M, Stern F, Kampmann A, Kotzem D, Tenkamp J, Walther F (2018) Microstructural Characterization of the Anisotropy and Cyclic Deformation Behavior of Selective Laser Melted AlSi10Mg Structures. Metals. 8(10):825
Biffi CA, Fiocchi J, Bassani P, Tuissi A (2018) Continuous wave vs pulsed wave laser emission in selective laser melting of AlSi10Mg parts with industrial optimized process parameters: microstructure and mechanical behaviour. Additive Manufacturing 24:639–646
Zhichao Dong , Xiaoyu Zhang , Wenhua Shi , Hao Zhou , HongshuaiLei,and Jun Liang, Study of Size Effect on Microstructure and Mechanical Properties of AlSi10Mg Samples Made by Selective Laser Melting, Materials .11(12) (2018) 2463
Mfusi BJ, Tshabalala LC, Popoola API, Mathe NR (2018) The effect of selective laser melting build orientation on the mechanical properties of AlSi10Mg parts. IOP Conf Series: Materials Science and Engineering 430:012028
Song B, Yan Q, Shi Y (2020) Comparative study of performance comparison of AlSi10Mg alloy prepared by selective laser melting and casting. J Mater Sci Technol 41:199–208
Tianyu Yu , Holden Hyer, Yongho Sohn , Yuanli Bai , DazhongWu,” Structure-property relationship in high strength and lightweight AlSi10Mg microlattices fabricated by selective laser melting Materials and Design 182 (2019) 108062
Zhong-hua Li, Yun-feiNie, Bin Liu, Ze-zhou Kuai, Miao Zhao,Fei Liu, Mechanical properties of AlSi10Mg lattice structures fabricated by selective laser melting, Materials & Design.192(2020) 108709
Dong Z, Liu Y, Li W, Liang J (2019) Orientation dependency for microstructure, geometric accuracy and mechanical properties of selective laser melting AlSi10Mg lattices. J Alloys Compd 791:490–500
Chen B, Yao Y, Song X, Tan C, Liang C, Feng J (2018) Microstructure and mechanical properties of additive manufacturing AlSi10Mg alloy using direct metal deposition. Ferroelectrics 523:153–166
G. Struzikiewicz , W. Ze˛bala, B. Słodki, “Cutting parameters selection for sintered alloy AlSi10Mg longitudinal turning”Measurement 138 (2019) 39–53
Palumbo B, Del Re F, Martorelli M, Lanzotti A, Corrado P (2017) Tensile properties characterization of AlSi10Mg parts produced by direct metal laser sintering via nested effects modeling. Materials 10(2):144
Ghasri-Khouzania M, Peng H, Attardo R, Ostiguy P, Neidig J, Billo R, Hoelzle D, Shankar MR (2019) Comparing microstructure and hardness of direct metal laser sintered AlSi10Mg alloy between different planes. J Manuf Process 37:274–280
Calignano F, Manfredi D, Ambrosio EP, Iuliano L, Fino P (2013) Influence of process parameters on surface roughness of aluminum parts produced byDMLS. Int J Adv Manuf Technol 67:2743–2751
BehroozJalalahmadi, Jingfu Liu, Jason Rios, John Slotwinski,ChristopherPeitsch, Arnold Goldberg, Timothy Montalbano,In-process defect monitoring and correction in additive manufacturing of aluminum alloys, Presented at the Vertical Flight Society’s 75th Annual Forum & Technology Display, Philadelphia, PA, USA, May 13-16, 2019
F. Calignanoa,, G. Cattanob,, D. Manfredi,”Manufacturing of thin wall structures in AlSi10Mg alloy by laser powder bed fusion through process parameters”,Journal of Materials Processing Tech. 255 (2018) 773–783
HitzlerE,Sert· E., Schuch A, Öchsner · M, Merkel3, B. Heine4 · E. Werner, Fracture toughness of L-PBF fabricated aluminium–silicon: a quantitative study on the role of crack growth direction with respect to layering, Progress in Additive Manufacturing . 5 (2020)259–266
Alexandra Inberg , Dana Ashkenazi ,Giora Kimmel · YosiShacham , Diamand, Adin Stern, Gold plating of AlSi10Mg parts produced by a laser powder-bed fusion additive manufacturing technique, Progress in Additive Manufacturing. . 5(2020) 395-404
N. Dresler, A. Inberg,D. Ashkenazi ,Y. Shacham-Diamand, · A. Stern, Silver Electro less Finishing of Selective Laser Melting 3D-Printed AlSi10Mg Artifacts, Metallography, Microstructure, and Analysis. 8(2019) 678-692
Scherillo F (2019) Chemical surface finishing of AlSi10Mg components made by additive Manufacturing. Manufacturing Letters 19:5–9
Xiaodong Xing , Xiaoming Duan , Tingting Jiang , Jiandong Wang and Fengchun Jiang, Ultrasonic Peening Treatment Used to Improve Stress Corrosion Resistance of AlSi10Mg Components Fabricated Using Selective Laser Melting, Metals .9(1) (2019) 103.
Maamoun AH, Elbestawi MA, Veldhuis SC (2018) Influence of Shot Peening on AlSi10Mg Parts Fabricated by Additive Manufacturing. J Manuf Mater Process 2(3):40
James Damon, Stefan Dietrich, Florian Vollert,JensGibmeier, Volker Schulze, Process dependent porosity and the influence of shot peening on porosity morphology regarding selective laser melted AlSi10Mg parts, Additive Manufacturing. 20 (2018) 458-464.
NE, Ramati S, Shneck R, Frage N, Yeheskel O, On the effect of shot-peening on fatigue resistance of AlSi10Mg specimens fabricated by additive manufacturing using selective laser melting (AM-SLM), Additive Manufacturing . 21 (2018) 458-464.
Author: E. Atzeni M. Barletta F. Calignano L. IulianoG. Rubino V. Tagliaferri, Abrasive Fluidized Bed (AFB) finishing of AlSi10Mg substrates manufactured by Direct Metal Laser Sintering (DMLS),Additive Manufacturing. 10 (2016) 15-23
Andrea El Hassanin, Maurizio Troiano, Alessia Teresa Silvestri,VincenzoContaldi, Fabio Scherillo, Roberto Solimene,Fabrizio Scala , Antonino Squillace and Piero Salatino, Influence of Abrasive Materials in Fluidised Bed Machining of AlSi10Mg Parts Made through Selective Laser Melting Technology,Key Engineering Materials. 183 (2019) 129-134.
Xiao Teng, Guixiang Zhang,Yugang Zhao & Yuntao Cui, Linguang Li & Linzhi Jiang, Study on magnetic abrasive finishing of AlSi10Mg alloy prepared by selective laser melting, The International Journal of Advanced Manufacturing Technology, 105 (2019) 2513-2521
U. Tradowsky, J. White, R.M. Ward, N. Read, W. Reimers, M.M. Attallah, Selective Laser Melting of AlSi10Mg: Influence of Post-Processing on the Microstructural and Tensile Properties Development.105 (2016) 212-222
Rosenthal RS, Stern A (2018) Heat treatment effect on the mechanical properties and fracture mechanism in AlSi10Mg fabricated by Additive Manufacturing Selective Laser Melting process. Materials Science & Engineering A 729:310–322
Hirata T, Kimura T, Nakamoto T (2020) Effects of hot isostatic pressing and internal porosity on the performance of selective laser melted AlSi10Mg alloys. Materials Science & Engineering A 772:138713
Hastie JC, Kartal ME, Carter LN, Attallah MM, Mulvihill DM (2020) Classifying shape of internal pores within AlSi10Mg alloy manufactured by laser powder bed fusion using 3D X-ray micro computed tomography: Influence of processing parameters and heat treatment. Mater Charact 163:110225
Girelli L, Giovagnoli M, Tocci M, Pola A, Fortini A, Merlin M, La Vecchia GM (2019) Evaluation of the impact behaviour of AlSi10Mg alloy produced using laser additive manufacturing. Materials Science & Engineering A 748:38–51
Uzan NE, Shneck R, Yeheskel O, Frage N (2017) Fatigue of AlSi10Mg specimens fabricated by additive manufacturing selective laser melting (AM-SLM). Materials Science & Engineering A 704:229–237
Liu B, Li B-Q, Li Z (2019) Selective laser remelting of an additive layer manufacturing process on AlSi10Mg. Results in Physics 12:982–988
Yu W, Sing SL, Chua CK, Tian X (2019) Influence of re-melting on surface roughness and porosity of AlSi10Mg parts fabricated by selective laser melting. J Alloys Compd 792:574–581
Wenhuiyu, Sweeleong sing, Xuelei tian, Chee kai chua, Effects of re-melting strategies on densification behavior and mechanical properties of selective laser melting AlSi10Mg parts, Proc. Of the 3rd Intl. Conf. on Progress in Additive Manufacturing,2010,pp.476-481.
Schanz J, Hofele M, Hitzler L, Merkel M, Riegel H (2016) Laser polishing of additive manufactured AlSi10Mg parts with an oscillating laser beam, machining, joining and modifications of advanced materials. Advanced Structured Materials 61:159–169
du Plessis A, Glaser D, Moller H, Mathe N, Tshabalala L, Mfusi B, Mostert R (2019) Pore closure effect of laser shock peening of additively manufactured AlSi10Mg. 3d Printing and Additive Manufacturing 6:245–252
Takata N, Liu M, Kodaira H, Suzuki A, Kobashi M (2020) Anomalous strengthening by supersaturated solid solutions of selectively laser melted Al–Si-based alloys. Additive Manufacturing 33:101152
Busisiwe J. Mfusi , Ntombizodwa R. Mathe , Lerato C. Tshabalala and Patricia AI. Popoola , The Effect of Stress Relief on the Mechanical and Fatigue Properties of Additively Manufactured AlSi10Mg Parts, Metals 9(11) (2016) 1216
Suzuki A, Sekizawa K, Liu M, Takata N, Kobashi M (2019) Effects of heat treatments on compressive deformation behaviors of lattice-structured alsi10mg alloy fabricated by selective laser melting. Adv Eng Mater:1900571
Hrbáčková T, Simson T, Koch J, Wolf G (2019) The effect of heat treatment on mechanical properties and microstructure of additively manufactured components. IOP Conf Series: Materials Science and Engineering 461:012026
Xiaohui Jiang , Wenjing Xiong, Lianfeng Wang, Miaoxian Guo and Zishan Ding, Heat treatment effects on microstructure-residual stress for selective laser melting AlSi10Mg,Materials science and Technology, 2019
Zakay A, Aghion E (2019) Effect of post-heat treatment on the corrosion behavior of alsi10mg alloy produced by additive manufacturing. The Minerals, Metals & Materials Society 71:1150–1157
Tridello A, Fiocchi J, Biffi CA, Chiandussi G, Rossetto M, Tuissi A, Paolino DS (2019) VHCF response of Gaussian SLM AlSi10Mg specimens: Effect of a stress relief heat treatment. Int J Fatigue 124:435–443
EladUzan N, Shneck R, Yeheskel O, Frage N (2018) High- temperature mechanical properties of alsi10mg specimens fabricated by additive manufacturing using selective laser melting technologies (AM-SLM). Additive Manufacturing 24:257–263
Rubben T, Revilla RI, De Graeve I (2019) Influence of heat treatments on the corrosion mechanism of additive manufactured AlSi10Mg. Corros Sci 147:406–415
Zhuo L, Wang Z, Zhang H, Yin E, Wang Y, Xu T, Li C (2019) Effect of post-process heat treatment on microstructure and properties of selective laser melted AlSi10Mg alloy. Mater Lett 234:196–200
Maamoun AH, Elbestawi M, Dosbaeva GK, Veldhuis SC (2018) Thermal post-processing of AlSi10Mg parts produced by Selective Laser Melting using recycled powder. Additive Manufacturing 21:234–247
Tang M, Pistorius PC (2017) Anisotropic mechanical behavior of AlSi10Mg parts produced by selective laser melting. The Minerals, Metals & Materials Society 69:516–522
Gong W, Qi J, Wang Z, Chen Y, Jiang J, Wang Z, Qi Y (2019) Microstructure and Mechanical Properties of Selective Laser Melting AlSi10Mg, 3rd International Symposium of Space Optical Instruments and Applications. Springer Proceedings in Physics 192:113–120
Li W, Li S, Liu J, Zhang A, Zhou Y, Wei Q, Yan C, Shi Y (2016) Effect of heat treatment on AlSi10Mg alloy fabricated by selective laser melting: Microstructure evolution, mechanical properties and fracture mechanism. Materials Science & Engineering A 663:116–125
Fite J, Prameela SE, Slotwinski J, Weihs T (2020) Evolution of the microstructure and mechanical properties of additively manufactured AlSi10Mg during room temperature holds and low temperature aging. Additive Manufacturing 36:101429
Majeed A, Ahmed A, Salam A, Sheikh MZ (2019) Surface quality improvement by parameters analysis, optimization and heat treatment of AlSi10Mg parts manufactured by SLM additive manufacturing. International Journal of Lightweight Materials and Manufacture 2(4):288–295
Majeed A, Muzamil M, Lv J, Liu B, Ahmad F (2019) Heat treatment influences densification and porosity of AlSi10Mg alloy thin-walled parts manufactured by selective laser melting technique. J Braz Soc Mech Sci Eng 41:267
Lv F, Shen L, Liang H, Xie D, Wang C, Tian Z (2019) Mechanical properties of AlSi10Mg alloy fabricated by laser melting deposition and improvements via heat treatment. Optik 179:8–18
Zhang, C., Zhu, H., Liao, H., Cheng, Y., Hu, Z., Zeng, X., Effect of heat treatments on fatigue property of selective laser melting AlSi10Mg, International Journal of Fatigue .116 (2018) 513-522.
Majeed A, Zhang YF, Lv JX, Peng T, Waqar S, Atta Z (2018) Study the effect of heat treatment on the relative density of slm built parts of alsi10mg alloy, CIE48 Proceedings. The University of Auckland, December 2-5
J. Fiocchi, .C.A. Biffi, C. Colombo, L.M. Vergani, and A. Tuissi, Ad Hoc heat treatments for selective laser melted Alsi10mg alloy aimed at stress-relieving and enhancing mechanical performances, Additive Manufacturing Validation and Control.72 (2020) 1118-1127
Di Giovanni MT, de Menezes JTO, Bolelli G, Cerri E, Castrodez EM (2019) Fatigue crack growth behavior of a selective laser melted AlSi10Mg. Eng Fract Mech 217:106564
Qiu L, Wang F, Yang Y, Guo L (2019) A new modification effect of eutectic Si in selective laser melted AlSi10Mg. Mater Sci Technol 35(6):709–715
DomfangNgnekou JN, Nadot Y, Henaff G, Nicolai J, Kan WH, Cairney JM, Ridosz L (2019) Fatigue properties of AlSi10Mg manufactured by Additive Layer Manufacturing. Int J Fatigue 119:160–172
Brandl E, Heckenberger U, Holzinger V, Buchbinder D (2012) Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): Microstructure, high cycle fatigue, and fracture behavior. Mater Des 34:159–165
Iturrioz A, Gil E, Petite MM, Garciandia F, Mancisidor AM, Sebastian MS (2018) Selective laser melting of AlSi10Mg alloy: influence of heat treatment condition on mechanical properties and microstructure. International Institute of Welding 62:885–892
Zyguła K, Nosek B, Pasiowiec H, Szysiak N (2018) Mechanical properties and microstructure of AlSi10Mg alloy obtained by casting and SLM technique. WSN 104:462–472
Casati R, Nasab MH, Coduri M, Tirelli V, Vedani M (2018) Effects of platform pre-heating and thermal-treatment strategies on properties of AlSi10Mg alloy processed by selective laser melting. Metals 8(11):954
Fousová M, Dvorský D, Michalcová A, Vojtěch D (2018) Changes in the microstructure and mechanical properties of additively manufactured AlSi10Mg alloy after exposure to elevated temperatures. Mater Charact 137:119–126
Aboulkhair NT, Maskery I, Tuck C, Ashcroft I, Everitt NM (2016) The microstructure and mechanical properties of selectively laser melted AlSi10Mg: The effect of a conventional T6-like heat treatment. Materials Science & Engineering A 667:139–146
Seabra M et al (2016) Selective laser melting (SLM) and topology optimization for lighter aerospace components. Procedia Struct Integr 1:289–296
Anil S, Anand PS, Alghamdi H, Jansen JA (2011) Dental implant surface enhancement and Osseo integration. In Tech Open Access Publ 1:83–108
Asgari H, Baxter C, Hosseinkhani K, Mohammadi M (2017) On microstructure and mechanical properties of additively manufactured AlSi10Mg_200C using recycled powder. Materials Science & Engineering A 707:148–158
Fathi P, Mohammadi M, Duan X, Nasiri AM (2018) A comparative study on corrosion and microstructure of direct metal laser sintered AlSi10Mg_200C and die cast A360.1 aluminum. Journal of Materials Processing Tech 259:1–14
Mohammadi M, HamedAsgari (2018) Achieving low surface roughness AlSi10Mg 200C parts using direct metal laser sintering. Additive Manufacturing 20:23–32
Fatemi A, Molaei R, Sharifimehr S, Phan N, Shamsaei N (2017) Multi axial fatigue behavior of wrought and additive manufactured Ti-6Al-4 V including surface finish effect. Int J Fatigue 100:347–366
Leon A, Aghion E (2017) Effect of surface roughness on corrosion fatigue performance of AlSi10Mg alloy produced by selective laser melting (SLM). Mater Charact 131:188–194
Alrbaey K, Wimpenny D, Tosi R, Manning W, Moroz A (2014) On optimization of surface roughness of selective laser melted stainless steel parts: a statistical study. J Mater Eng Perform 23:2139–2148
Read N, Wang W, Essa K, Attallah MM (2015) Selective laser melting of AlSi10Mgalloy: process optimization and mechanical properties development. Mater.Des. 65:417–424
Bacchewar PB, Singhal SK, Pandey PM (2007) Statistical modelling and optimization of surface roughness in the selective laser sintering process. Proc Inst Mech Eng Part B: J Eng Manuf 221:35–52
Polmear IJ (2006) Light alloys: from traditional alloys to nan crystals. Elsevier, Oxford, UK
Kimura T, Nakamoto T (2016) Microstructures and mechanical properties of A356 (AlSi7Mg0.3) aluminum alloy fabricated by selective laser melting. Materials Design 89:1294–1301
Heng Rao, Stephanie Giet , Kun Yang , Xinhua Wu, Chris H.J. Davies,” The influence of processing parameters on aluminium alloy A357 manufactured by Selective Laser Melting, Materials and Design 109 (2016) 334–346
Aversa A, Lorusso M, Trevisan F, Ambrosio EP, Calignano F, Manfredi D, Biamino S, Fino P, Lombardi M, Pavese M (2017) Effect of process and post-process conditions on the mechanical properties of an A357 alloy produced via laser powder bed fusion. Metals 7(2):68
Yang KV, Rometsch P, Jarvis T, Rao J, Cao S, Davies C, Wu X (2018) Porosity formation mechanisms and fatigueresponse in Al-Si-Mg alloys made by selective laser melting. Materials Science & Engineering A 712:166–174
Yang KV, Rometsch P, Davies CHJ, Huang A, Wu X (2018) Effect of heat treatment on the microstructure and anisotropy in mechanical properties of A357 alloy produced by selective laser melting. Mater Des 154:275–290
Bassoli E, Denti L, Comin A, Sol A, Togno E (2018) Fatigue behavior of as-built L-PBF A357.0 parts. Metals 8(8):634
Tonelli L, Liverani E, Valli G, Fortunato A, Ceschini L (2020) Effects of powders and process parameters on density and hardness of A357 aluminum alloy fabricated by selective laser melting. Int J Adv Manuf Technol 10(6):371–383
Rao JH, Zhang Y, Zhang K, Wu X, Huang A (2019) Selective laser melted Al-7Si-0.6Mg alloy with in-situ precipitation via platform heating for residual strain removal. Mater Des 182:108005
Lorusso M, Trevisan F, Calignano F, Lombardi M, Manfredi D (2020) A357 Alloy by LPBF for industry applications. Materials 13:1488
Li YX, Zhang PF, Bai PK, Wu LY, Liu B, Zhao ZY (2018) Microstructure and properties of Ti/TiBCN coating on 7075 aluminum alloy by laser cladding. Surf Coat Technol 334:142–149
Zhao X, Song B, Fan WR, Zhang YJ, Shi YS (2016) Selective laser melting of carbon/ AlSi10Mg composites: microstructure, mechanical and electronical properties. J Alloys Compd 665:271–281
Laorden LM, Rodrigo P, Torres B, Rams J (2017) Modification of microstructure and superficial properties of A356 and A356/10%SiCp by selective laser surface melting (SLSM). Surf Coat Technol 309:1001–1009
Bao S, Tang K, Kvithyld A, Tangstad M, Engh TA (2011) Wettability of Aluminum on Alumina. Metall Mater Trans B Process Metall Mater Process Sci 42(6):1358–1366
Shen P, Fujii H, Matsumoto T, Nogi K (2004) Critical Factors Affecting the Wettability of a-Alumina by Molten Aluminum. J Am Ceram Soc 87(7):1265–1273
Sercombe TB, Schaffer GB Rapid manufacturing of aluminum components. Science 301(5637):1225–1227
Gu DD (2015) Laser additive manufacturing of high-performance materials, Springer-Verlag. Berlin 2015
Gu DD, Chang F, Dai DH (2015) Selective laser melting additive manufacturing of novel aluminum based composites with multiple reinforcing phases. ASME J Manuf Sci Eng 137(2):021010
Fu CH, Guo YB (2014) Three-Dimensional Temperature Gradient Mechanism in selective laser melting of Ti-6Al-4V. ASME J Manuf SciEng 136(6):061004
Yadroitsev I, Bertrand P, Smurov I (2007) Parametric analysis of the selective laser melting process. Appl Surf Sci 253:8064–8069
Jue JB, Gu DD, Chang K, Dai DH (2016) Microstructure evolution and mechanical properties of Al-Al2O3 composites fabricated by selective laser melting. Powder Technol 310:80–91
Olakanmi EO (2013) Selective laser sintering/melting (SLS/SLM) of pure Al, Al-Mg, and Al-Si powders: Effect of processing conditions and powder properties. J Mater Process Technol 213(8):1387–1405
Gu DD, Ma CL, Xia MJ, Dai DH, Shi QM (2017) A multiscale understanding of the thermodynamic and kinetic mechanisms of laser additive manufacturing. Engineering 3:675–684
Dai DH, Gu DD (2016) Influence of thermodynamics within molten pool on migration and distribution state of reinforcement during selective laser melting of AlN/ AlSi10Mg composites. Int J Mach Tools Manuf 100:14–24
Song B, Wang ZW, Yan Q, Zhang YJ, Zhang JL, Cai C, Wei QS, Shi YS (2017) Integral method of preparation and fabrication of metal matrix composite: selective laser melting of in-situ nano/submicro-sized carbides reinforced iron matrix composites. Mater Sci Eng A 707:478–487
Almangour B, Grzesiak D, Yang JM (2017) Scanning strategies for texture and anisotropy tailoring during selective laser melting of TiC/316L stainless steel nanocomposites. J Alloys Compd 728:424–435
Gu DD, Meng GB, Li C, Meiners W, Poprawe R (2012) Selective laser melting of TiC/Ti bulk nanocomposites: influence of nanoscale reinforcement. Scr Mater 67:185–188
Han QQ, Geng YQ, Setchi R, Lacan F, Gu DD, Evans SL (2017) Macro and nanoscale wear behaviour of Al-Al2O3 nanocomposites fabricated by selective laser melting. Compos Part B Eng 127:26–35
Thijs L, Kempen K, Kruth J-P, Van Humbeeck J (2013) Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder. Acta Mater 61:1809–1819
Aboulkhair NT, Tuck C, Ashcroft I, Maskery I, Everitt NM (2015) On the precipitation hardening of selective laser melted AlSi10Mg. Metall Mater Trans A 46:3337–3341
Leon A, Aghion E (2017) Effect of surface roughness on corrosion fatigue performance of AlSi10Mg alloy produced by Selective Laser Melting (SLM). Mater Charact 131:188–194
Dai D, Dongdong G (2016) Influence of thermodynamics within molten pool on migration and distribution state of reinforcement during selective laser melting of AlN/AlSi10Mg composites. Int J Mach Tool Manu 100:14–24
Daia D, Gua D, Xiaa M, Maa C, Chena H, Zhao T, Hong C, Gasser A, Poprawe R (2018) Melt spreading behavior, microstructure evolution and wear resistance of selective laser melting additive manufactured AlN/AlSi10Mg nanocomposite. Surf Coat Technol 349:279–288
Dai D, Gu D, Poprawe R, Xia M (2017) Influence of additive multilayer feature on thermodynamics, stress and microstructure development during laser 3D printing of aluminum-based material. Sci Bull 62:779–787
Dongdong G, Jue J, Dai D, Lin K, Chen W (2018) Effects of dry sliding conditions on wear properties of al-matrix composites produced by selective laser melting additive manufacturing. J Tribol 740:021605
Liao H, Zhu H, Xue G, Zeng X (2019) Alumina loss mechanism of Al2O3-AlSi10 Mg composites during selective laser melting. J Alloys Compd 785:286–295
Dadbakhsh S, Hao L (2012) Effect of Al alloys on selective laser melting behaviour and microstructure of in situ formed particle reinforced composites. J Alloys Compd 541:328–334
Lorusso M, Aversa A, Manfredi D, Calignano F, Ambrosio EP, Ugues D, Pavese M (2016) Tribological behavior of aluminum alloy AlSi10Mg-TiB2 composites produced by direct metal laser sintering (DMLS). Journal of Materials Engineering and Performance, ASM International 25:3152–3160
Li Y, Gu D, Zhang H, Xi L (2020) Efect of trace addition of ceramic on microstructure development and mechanical properties of selective laser melted AlSi10Mg alloy. Chin J Mech Eng 33:33
Li XP, Ji G, Chen Z, Addad A, Wu Y, Wang HW, Vleugels J, Van Humbeeck J, Kruth JP (2017) Selective laser melting of nano-TiB2 decorated AlSi10Mg alloy with high fracture strength and ductility. Acta Mater 129:183–193
Zhao Z, Bai P, Misra RDK, Li MDRGY, Zhang J, Tan L, Ding JGT, Du W, Guo Z (2019) AlSi10Mg alloy nanocomposites reinforced with aluminum-coated graphene: Selective laser melting, interfacial microstructure and property analysis. J Alloys Compd 792:203–214
Tiwari JK, Mandal A, Sathish N, Agrawal AK, Srivastava AK (2020) Investigation of porosity, microstructure and mechanical properties of additively manufactured graphene reinforced AlSi10Mg composite. Additive Manufacturing 33:101095
Wang Y, Shi J (2020) Effect of hot isostatic pressing on nanoparticles reinforced AlSi10Mg produced by selective laser melting. Materials Science & Engineering A 288:139570
Liu X, Zhao C, Zhou X, Eibl F, Shen Z, Liu W, Meiners W (2019) CNT-reinforced AlSi10Mg composite by selective laser melting: microstructural and mechanical properties. Mater Sci Technol:1038–1045
Zhao X, Song B, Fan W, Zhang Y, Shi Y (2016) Selective laser melting of carbon/ AlSi10Mg composites: microstructure, mechanical and electronical properties. J Alloys Compd 665:271–281
C. Gaoa, , Z. Wanga , Z. Xiaoa, , D. Youa , K. Wongc , A.H. Akbarzadeh,Selective laser melting of TiN nanoparticle-reinforced AlSi10Mg composite: Microstructural, interfacial, and mechanical properties, Journal of Materials Processing Tech 281 (2020) 116618
Funding
This research received no external funding
Author information
Authors and Affiliations
Contributions
•Bheemavarapu Subba Rao: Conceptualization, Methodology, Data collection, Writing-review, and editing.
•Thella Babu Rao: Review, Editing, and Supervision.
•All authors have read and agreed to publish a version of the manuscript.
Corresponding author
Ethics declarations
This article is a review article
Consent to participate
'Not applicable'
Consent for Publication
'Not applicable'
Conflict of Interest
The authors declare that they have no conflict of interest. This review article does not contain any studies with human participants or Animals performed by any of the authors.
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Rao, B.S., Rao, T.B. Mechanical and Tribological Properties of 3D printed Al-Si alloys and composites: a Review. Silicon 14, 5751–5782 (2022). https://doi.org/10.1007/s12633-021-01340-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12633-021-01340-9