Abstract
Purpose
Stormwater bioretention systems are widely used to treat diffuse infiltration of runoff from paved surfaces and roofs. Substantial questions remain about the hydraulic performance and the accumulation of pollutants in systems over the long term. Data of metal accumulation of systems with operational times >10 years currently is limited. This study deals with the accumulation of metals in a variety of long-term operational bioretention systems (11–22 years) to derive further operation recommendations for the water authorities.
Materials and methods
The hydraulic conductivity of the bioretention systems in field was measured using a double ring infiltrometer. Media soil samples from 22 diverse designed systems were collected across the surface and at intervals up to a depth of 65 cm to determine the spatial accumulation of Zn, Cu, Pb and Cd. Leaching experiments of selected bioretention media soils were derived to assess the metal leachability by water.
Results and discussion
The hydraulic performance of most bioretention systems still met the technical guidelines of Germany even after long-term operation. Considerable metal accumulation occurred in the topsoil (0–20 cm). Median concentrations of all metals are highest at the soil surface (0–10 cm), decreasing with increasing depth. High concentrations were determined at the inflow points of the runoff waters, whereas concentrations at more than 1.5 m distance from the inflow were only slightly increased compared to the initial soil concentrations. Leachability tests have shown that most of the metals deposited in bioretention soils are only slightly water soluble. No concentrations exceeding the threshold values of the German Soil Contamination Ordinance for the pathway soil to groundwater could be determined.
Conclusions
The hydraulic conductivity of the bioretention systems is given even well after long-term operation. Most of the metal accumulation is concentrated in the top 20 cm; concentrations decrease rapidly and mostly reach background/initial concentrations after depths of 30 cm. The water-soluble metals are all below the trigger values of the German Soil Act. This underlines the strong retention capacity of long-term bioretention systems after long-term operational times.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
1 Introduction
Due to rapid urbanization, sealed areas for infrastructural, residential and commercial purposes are considered to increase worldwide (García et al. 2014; Liu et al. 2014). This in turn leads to reduced rainwater infiltration and evaporation and as a consequence, to larger storm water volumes and runoff peaks in urban areas (Davis et al. 2003; Fletcher et al. 2013). Stormwater runoff often contains high levels of contaminants from road and building materials, vehicle components and traffic activity or dog faeces (Folkeson et al. 2009; Parker et al. 2010). The most recognized and examined contaminants in stormwater runoff are suspended solids, heavy metals, PAHs, microbial contaminants and nutrients such as nitrogen and phosphorus (Blanchard et al. 2001; Göbel et al. 2007; Ingvertsen et al. 2012a; Kayhanian et al. 2012; Li et al. 2014).
To reduce the increasing amount of runoff water and minimize the contamination of receiving water, water authorities in many countries all over the world encourage structural stormwater treatment techniques and processes, often as part of their “best management practices (BMPs)” (Hunt et al. 2006; Marsalek et al. 2006; Prince George’s County 2007; Lim et al. 2015). The diffuse infiltration of runoff from sealed surfaces or roofs into bioretention systems (also known as bioretention cells, areas; raingardens; biofilters; bioswales) is an important component of the BMPs practice and is common in commercial and residential areas (Davis et al. 2006; Dietz 2007; Boivin et al. 2008; Piguet et al. 2008).
In all these systems, the soil serves as a natural filter to reduce runoff quantity via water retention and evapotranspiration and to promote pollutant retention through physical and chemical retardation. They are often constructed as shallow depressed sites to pool and infiltrate stormwater. The design and construction differs widely; however, they are generally constructed using several layers of soil media (Lundy et al. 2012; LeFevre et al. 2014). The design often includes a top soil filter layer of 10–20 cm thickness with an adequate organic matter content that provides precipitation water, root space and nutrients for the vegetation and soil microorganisms which positively supports mechanical, chemical and biological pollutant retardation and removal (Davis et al. 2001; Roy-Poirier et al. 2010; LeFevre et al. 2014). At the bottom of the system, a high permeability layer improves the drainage of the infiltrated runoff water. Between these two layers, a layer with intermediate grain sizes is commonly found which limits the migration of fine soil particles to the bottom layer (Lundy et al. 2012).
In some cases, underdrain structures are installed to meliorate underlying native soil with low permeability (Roy-Poirier et al. 2010). To avoid erosion processes of the systems, they are often covered with grass, small plants, shrubs, or trees.
It is essential for the performance of the bioretention systems that the soils offer high infiltration rates while at the same time providing sufficient retardation time for the runoff waters. International guideline recommendations for the hydraulic conductivity (K) of the soil vary considerably, ranging from 3.5e−06 m/s in the USA/New Zealand, to 1.4e−05 and 5.5e−05 m/s in Australia to e−04 and e−06 m/s in Austria/Germany (Le Coustumer et al. 2009; DWA-A 138 2005). Lindsey et al. (1992) and Le Coustumer et al. (2009, 2012) who investigated the hydraulic performance of biofiltration systems after long-term use, reported that after a few years of operation, more than 40 % had a lower hydraulic conductivity than that recommend in the guidelines. Li and Davis (2008a) determined a decrease of hydraulic conductivity of two soil filter media in column experiments from 1.5e−02 and 2.e−02 to less than 2.8e−05 m/s due to particle clogging.
Several studies were performed to analyse the efficiency of pollutant reduction of bioretention systems under field and laboratory conditions (e.g. Davis et al. 2006; Ingvertsen et al. 2012a, 2012b; Søberg et al. 2014). In most cases, bioretention systems reduced the mass of a variety of pollutants in the outflow by a very high degree (Kabir et al. 2014). Hunt et al. (2006) found that removal of the incoming metals Zn and Cu was more than 98 % and for Pb approximately 80 %. Li and Davis (2009) determined median reduction rates of between 92–99, 65–96 and 83–100 % for Zn, Cu and Pb respectively, in two bioretention cells over a period of 15 storm events. Zhang et al. (2014) determined high removal rates for TPHs, glyphosate, DBP, DEHP, pyrene and naphthalene (>80 % load reduction) at a biofilter system in Australia.
For more than 20 years, bioretention systems (areas or swales) have represented the state-of-the-art for the management of surface and roof runoff for urban areas in Germany. Nevertheless, the planning guidelines in Germany only deal with these systems during the construction and installation phase; substantial questions remain about the long-term performance and contamination status of these systems.
The issues of particular importance are the potential for clogging and their long-term pollutant removal capabilities (Le Coustumer et al. 2012). Some studies can be found concerning the accumulation of metals over operational periods from 2 to 10 years (Dietz and Clausen 2006; Achleitner et al. 2007; Li and Davis 2008b; Jones and Davis 2013; Lucke and Nichols 2015). To our knowledge, bioretention metal accumulation data are currently limited and only two studies deal with the pollutant status of bioretention systems over operational times >10 years (Ingvertsen et al. 2012a; Paus et al. 2014). Thus, the aim of this study was to determine the spatial accumulation and leaching potential of metals (Zn, Cu, Pb, Cd) in a variety of long-term operational bioretention systems (11–22 years) to derive further operation recommendations for the water authorities.
2 Material and methods
2.1 Study sites
The investigated bioretention systems are located in urban areas of different cities in Germany. The systems are bioswales with or without underlying underdrains (Fig. 1). The systems treat stormwater from parking lots, sidewalks, residential roads, or roofs and are constructed according to the technical guidelines of the German Association for Water, Wastewater and Waste (DWA-A 138 2005). Table 1 summarizes the requirements for the construction of bioretention swales in Germany, whereas Table 2 shows a classified register of the systems recording the use of the surrounding area, drainage area type and years of operation.
2.2 Sampling and data analysis
Soil samples were collected from low points at the inflow zones of each site and from a second point at 1.5 m distance from the inflow. A stainless steel shovel was used to dig up a profile (70 × 70 cm). The depth of the profile depended on the bioswale base, limited by the installation of a geotextile, an underdrain or the origin soil. Therefore, the sampling depth varied as well as the bioretention soil thicknesses across the sampled sites. In general, samples of depths 0–10, 10–20, 20–30 cm were collected; for some systems as well, the soil depth was 30–65 cm. Composite soil samples of the prescribed depths were taken to a laboratory for chemical analysis. Before analysis, all soil samples were air dried and sieved through <2 mm.
In order to verify the influence of land use and drainage area type on metal accumulation and distribution of the sampled bioretention systems, the data were classified according to the following runoff categories: (a) commercial, (b) main roads, (c) roofs (=roofs with zinc gutters and downpipes), (d) parking lots and (e) residential roads.
2.3 Measurements of hydraulic conductivities
The hydraulic conductivity of the bioretention systems in field was determined using a double ring infiltrometer according to DIN 19682-7 (2015)-08. In total, 48 measurements were conducted.
2.4 S4 elution (batch S4) of system no. 9
The metal leachability by water was determined according to DIN 38414-4 (1984). This method is well established and widely used in Germany and other countries (Delay et al. 2007; Alvarenga et al. 2012; Kluge et al. 2014). Deionised water was added to the soil samples with a ratio of soil to water by 1:10. Afterward, the samples were treated in an overhead shaker for 24 h and then filtered through 0.45 μm.
2.5 Elemental analyses
The pseudo total metal concentrations of soil samples was determined by aqua regia digestion in closed vessels in a microwave oven (Perkin Elmer) according to DIN ISO 11466 (1997). The concentrations of Cd, Cu, Pb and Zn in the digests were measured by ICP-MS (Varian 810/820-MS) and by graphite tube atomic absorption spectrophotometer (Varian SpectrAA 800Z) according to ISO 11885 (2007). All samples were analysed in triplicates. Quality assurance procedures were carried out to ensure reliability of the results. Analytical grade reagents and bi-distilled water were used during all procedures. A certified reference material was used as the quality control sample. Limits of quantification (LOQ) for measured metals were as follows: Pb 0.5 ppb, Cu 1 ppb, Cd 0.2 ppb and Zn 10 ppb. The concentrations of Cd, Cu, Pb and Zn in the soil solutions of S4 elution were measured by ICP MS (Varian 810/820-MS). The LOQ were as follows: Pb 10 ppb, Cu 1 ppb, Cd 0.5 ppb and Zn 1 ppb.
2.6 Comparison of metal concentrations with concentrations at the construction phase
Only limited information on the initial metal concentrations of the soils used in construction of the bioretention systems was available. Therefore, it is difficult to determine pollutant accumulation due to runoff infiltration. Nevertheless, in Germany, it is required to use clean soils to build bioretention systems.
This point is formalized in a technical regulation put forward by the German Association for Water, Wastewater and Waste (DWA-A 138 2005). The DWA requires that soils used in the construction of bioretention systems must have lower initial concentrations than the Z0 soil as defined by the Working Group for Waste (LAGA 2003) as a recycling (construction) standard.
The concentrations defined for the Z0 soil are equal to the precautionary values for the soil texture sand prescribed by the German Federal Soil Protection and Contamination Ordinance (BBodSchV 1999) (see Table 3). We compared our results to these Z0 concentrations and defined them as maximum initial concentrations in order to have an indication of metal accumulation by infiltrated water. Table 3 presents the assignment criteria and the precautionary values of the German Soil Act (BBodSchV 1999) for different soil textures.
3 Results and discussion
3.1 Hydraulic performance
The hydraulic conductivity represents a good basis for evaluating the hydraulic performance of bioretention systems. The DWA A-138 (2005) defines a technically infiltration rate of between 1e−03 and 1e−06 m/s. The results were differentiated by the texture into two categories: (i) sand/loamy sand and (ii) sandy loam/silty loam (Fig. 2). They express the main texture classes (sand and loam/silt), which are dominant in the two regions studied (Berlin/Brandenburg and Nord-Rhine Westfalia).
The median of the hydraulic conductivity in predominantly sandy systems is 1.3e−04 m/s, ranging from 9.2e−04 to 5.6e−07 m/s, at the sandy loam/silty loam systems the median hydraulic conductivity is 1.4e−05, with a range between 7.5e−05 and 6.9e−07 m/s (Fig. 2). Thus, most of the sampled systems correspond well with the recommended hydraulic conductivity of the technical guidelines in Germany. Only 4 topsoils of in total 48 show lower hydraulic conductivity than 1e−6. Lindsey et al. (1992) and Le Coustumer et al. (2009, 2012), who also investigated the hydraulic performance of biofiltration systems after long-term use, reported that more than 40 % of the investigated systems had a lower hydraulic conductivity than that recommend in the guidelines.
3.2 Vertical distribution of metals in bioretention soils
Metal concentrations in bioretention soils differ widely from system to system. Figure 3 shows the total concentrations of Cd, Pb, Cu and Zn at different bioretention soil depths. The median concentrations of all metals are highest at the soil surface (0–10 cm) and decrease with increasing depth. Zn concentrations in the first soil layer (0–10 cm) of the bioretention systems are the highest, with levels ranging from 2 to 1800 mg/kg, followed by Cu (5.7 to 210 mg/kg), Pb (12 to 160 mg/kg) and Cd (0.07 to 1.2 mg/kg). Highest metal concentrations often were found at the inflow points of the systems. This might be a consequence of heterogeneous infiltration pattern caused by rainfall events with low to medium intensity. At these events, only small inlet parts of the bioretention systems are flooded and led to a uniform runoff and consequently metal distribution. Jones and Davis (2013) also found a decrease of metal concentrations with distance from the inflow point at a bioretention cell after a 4-year operational time.
When we compare the median concentrations with the Z0 values (maximum initial concentrations; see Table 3), the median concentrations at the topsoil increased by factor of 2.3 for Zn, 1.3 for Cu, 1.2 for Pb and 1.1 for Cd. Higher median concentrations than Z0 are also determined at the soil depth 10–20 cm for Cd and Zn. Relating all metal concentrations to the precautionary values of the BBodSchV (1999), out of a total of 119 soil samples, we determined 72 exceeding the threshold values for Zn, 40 for Cu, 33 for Pb and 22 for Cd. At the soil depth 20–35 cm, a sharp decrease of the median concentrations of all metals was observed, which is to be expected as most topsoils used as bioretention media usually have adequate retention capacities due to filtration, precipitation and sorption processes.
The determined metal capture in the top soil layers of the bioretention systems agrees with the findings of previous laboratory and field studies related to stormwater bioretention (e.g. Davis et al. 2003; Li and Davis 2008a; Hatt et al. 2008; Blecken et al. 2011; Ingvertsen et al. 2012b; Jones and Davis 2013; Paus et al. 2014). The finding that most of the metals are concentrated at the top layer is also in line with other studies related to the long-term accumulation of metals by infiltrating runoff water, among other sources.
In a review of metal concentrations in roadside soils, Werkenthin et al. (2014) pointed out that the concentrations decreased between 57 and 75 % at soil depths between 15 and 75 cm compared to topsoil concentrations. At soil depths between 10 and 30 cm, Dierkes and Geiger (1999) determined a reduction of Cu, Pb and Zn concentrations ranging from 75 to 93 %; for Cd, the reduction was much less (30–40 %). The sample data suggest that considerable metal accumulation has occurred at the soil depth 0–20 cm during the long-term operation of the systems.
3.3 Influence of land use type on metal accumulation
In order to compare various drainage area types on metal accumulation and distribution of the sampled bioretention systems, Fig. 4 shows the metal concentration in the topsoil (0–10 cm) for the following runoff categories: (a) commercial, (b) main roads, (c) parking lots, (d) roofs with zinc gutters and (e) residential roads. Median Zn concentrations are significantly higher in topsoils at systems with runoff drainage from roofs with zinc gutters, followed by systems with runoff drainage from main roads. Higher median concentrations of Cd and Pb were found in systems with runoff drainage from parking lots. Median Cu soil concentrations are more or less in the same order of magnitude for all drainage area types. Lowest metal concentrations are determined for the drainage area types “commercial” and “residential roads”. The distribution of the metals in topsoil corresponds well with the distribution of average metal concentrations from different runoff surface types reported by Göbel et al. (2007).
3.4 Long-term accumulation and comparison of metal concentrations at different time steps of two bioretention systems
Figure 5 shows the heavy metal concentrations in soil matrix of system no. 9 at different time steps. The coordinates, metal soil concentrations and S4 elution concentrations of different soil depths were obtained from the data of a technical report of Schöttler and Remmler (1999), for system no. 11 from a technical report by Hiller et al. (2001).
The system is located in a residential area; the catchment area of the infiltration water is a roof; and the water passes through a galvanized roof gutter and infiltrates directly into the adjacent soil. The soil texture of the soil medium is silty sand.
Metal concentrations determined in the year 2014 mostly accumulated at the upper 10 cm, rapidly decreasing to initial concentrations with increasing depth. Compared to the initial concentrations of the topsoil (0–10 cm) of the year 1994 at the inflow, Pb, Cd and Zn concentrations increased by a factor of 7, 6 and 42. In contrast, the metal concentrations of the topsoil (0–10 cm) at 1 m distance to the inflow (mixed sample 2014) are, compared to the initial concentrations of 1994, only slightly increased. The high Zn concentration in the inflow point (0–10 cm) could be explained due to the corrosion of Zn from the galvanized rain gutter. Göbel et al. (2007) pointed out that runoff from roofs constructed with Zn gutters and downpipes often release higher metal concentrations than runoff from high trafficked areas. Due to corrosion by rain, not only Zn in particular but also Cd and Cu are released to the environment. He et al. (2001) investigated corrosion rates of zinc roofing materials and measured decreasing metal concentrations in roof runoff after initially high concentrations, reaching more or less constant concentrations with time.
This trend is also reflected by the rapid increase of all soil metal concentrations in the topsoil within the first 3 years of operation, except Cu (comparison of the mixed sample 1994 to the inflow sample 1997; Fig. 4). The Cu concentrations at the topsoil of both mixed and inflow samples of the year 2014 show a different distribution with lower concentrations compared to 1994, similarly for 1997. One explanation for these finding could be the preferred association of Cu with organic matter, which significantly increases the leachability compared to Pb and Zn and thus leads to a stronger leaching to the subsoil. Increased Cu leaching from bioretention media (soils) was also found by Sauvé et al. (2000), Li and Davis (2008a), Trowsdale and Simcock (2011) and Mullane et al. (2015). Li and Davis (2008a) observed a strong release of Cu from their investigated bioretention media and also put this down to a stronger association with organic matter and a high solubility by water.
Increased leaching and displacement of Cu was also detected in roadside soils, which is similarly characterized by high runoff infiltration (Bäckström et al. 2004 and Kocher et al. 2005).
The Cd concentrations at the inflow of the year 1997 were higher than those of the year 2014 at all investigated depths. A rapid leaching and a transfer to lower soil layers might be a reason for this, since Cd is the most mobile of the elements analysed (Alloway 2006) and mainly occurs in a dissolved fraction in runoff (e.g. Dierkes and Geiger 1999; Preciado and Li 2006). Concentrations exceeding the precautionary values of the BBodSchV were determined at the topsoil layer (0–10 cm) for all investigated metals at the inflow, whereas the concentrations at 1.5 m distance are well below the values with the exception of Zn in the mixed sample 2014 and Cu at all sample depths.
Cd, Pb, Cu and Zn soil concentrations of system no. 11 are shown in Fig. 6. The coordinates and metal soil concentrations were obtained from a technical report by Hiller et al. (2001). The system is located in a commercial area; the catchment area of the infiltration water is an asphalt parking and truck-manoeuvering area at a logistics center; and the water passes through a channel of concrete and infiltrates into the adjacent soil. The soil texture of the soil media ranges from silty sand at the top layer (0–10 cm) to medium sand at the bottom layer (10–65 cm).
Compared to the raised portion of the system, at 1.5 m distance from the inflow, infiltrating water led to a sediment deposition of about 20 cm due to washed up and accumulated particles. The concentrations of all metals are strongly increased at the accumulated sediment (0 ± 20 cm) compared to the soil metal concentration of the years 2001 and 2014.
In contrast, data of mixed samples at 1 m distance from the inflow for the year 2014 show only a slight increase in metal concentrations compared to the inflow samples of the year 2001, except Zn and to a certain extent Cd. For these metals, decreasing metal concentrations at the top soil (0–10 cm) could be observed.
One explanation for this finding is a slight leaching of the initial soil metal concentrations due to long-term infiltration over a timespan of 13 years. Dietz and Clausen (2006) also found a decrease of metals in a bioretention system after 2 years of operation and pointed out that the investigated bioretention soils serve as a source of metals. Our data suggest that the accumulated sediment is a likely sink for the incoming metals. The concentrations of Zn and Pb at the inflow are at 1770 and 130 mg/kg respectively, much higher than those determined by other authors (Jones and Davis 2013; Paus et al. 2014). Jones and Davis (2013) reported concentrations of Pb = 64 mg/kg, Cu = 49 mg/kg and Zn = 257 mg/kg near the inflow at a bioretention system after 4 years of operation. Observed mean Zn and Cu concentrations of Paus et al. (2014) at the topsoil layer of different bioretention systems after periods of operation ranging from 7 to 13 years are 2–6 times lower than those reported by Jones and Davis (2013). The higher concentrations could be explained by the longer operation time of the investigated bioretention systems and by the different runoff origin. All metal concentrations at the sediment are at or above the precautionary values of the BBodSchV (1999); all metals at the origin top layer (0–10 cm) of the year 2014 (inflow) and at 1.5 m distance are below the precautionary values of the BBodschV (1999), except Pb, for which we observed a marginal exceeding of the precautionary values at the soil depth 0–5 cm.
3.5 Batch leaching tests of the soils in long-term operating bioretention systems
The concentrations of water-soluble heavy metals determined by S4 elution of system no. 9 are presented exemplarily in Fig. 7. The results show that most of the metals deposited in bioretention soils are only slightly water soluble. According to the threshold values of the BBodSchV for the soil to groundwater path, no concentrations measured exceeded the precautionary value. Pb and Cd concentrations of the S4 elution were below the detection limit; therefore, no data comparison was possible. A comparison of the water-soluble concentrations of the years 1997/2014 shows a strong increase in Zn and a moderate decrease of Cu. This is in line with the finding of increasing Zn concentrations and decreasing Cu concentrations of the topsoil of system no. 9 (Fig. 4). Overall, we eluted 49 samples of 11 sample points of six different bioretention systems in different depths with the method of 1:10 elution (Table 4). When we compared the trigger values of the BBodSchV (1999)—pathway soil to groundwater—for all investigated metals, no exceeding values were detectable (Tables 3 and 4).
4 Conclusions
After long-term operation, the hydraulic performance (ksat) of the bioretention systems is mostly given and corresponds well with the recommended hydraulic conductivity of the technical guidelines of Germany. Mostly, metal accumulation is concentrated in the top 20 cm, which is in agreement with findings of other authors. In the underlying soil layers, all concentrations decrease rapidly and mostly reach background, i.e. initial concentrations after depths >30 cm. However, in some cases, we found very high metal concentration even in deeper soil layers. Obviously, this is a result of pre-polluted built-in substrates (anthropogenic and technical materials, diagnosed by colour, texture, smell), which were used as construction substrate for the bioretention systems.
However, very high metal concentrations were found at the inflow points with runoff drainage from roofs and parking lots. The same is true for drainage runoff from commercial areas. This might be a consequence of heterogeneous infiltration pattern caused by rainfall events with low to medium intensity. Then, only small inlet parts of the bioretention systems are flooded. Consequently, the following reasons for the heterogeneous metal distributions can be pointed out: (a) first flush effects, (b) system geometry of the bioretention system and (c) heterogeneity of the soil hydraulics.
In order to improve bioretention systems, we suggest regularly a replacement of the accumulated sediments or soils at the inflow points after 20–25 years as a routine maintenance. Another possibility could be a technical optimization of the bioretention systems leading to a more homogeneous infiltration of runoff water. Both might be an adequate solution to avoid critical violation of thresholds in order to protect groundwater resources.
References
Achleitner S, Engelhard C, Stegner U, Rauch W (2007) Local infiltration devices at parking sites-experimental assessment of temporal changes in hydraulic and contaminant removal capacity. Water Sci Technol 55(4):193–200
Alloway BJ (2006) Heavy metals in soils. Environmental pollution. Springer, Dordrecht
Alvarenga P, Palma P, De Varennes A, Cunha-Queda AC (2012) A contribution towards the risk assessment of soils from the São Domingos mine (Portugal): chemical, microbial and ecotoxicological indicators. Environ Pollut 161:50–56
Bäckström M, Karlsson S, Backman L, Folkeson L, Lind B (2004) Mobilisation of heavy metals by deicing salts in a roadside environment. Water Res 38:720–332
BBodSchV (1999) Bundes-Bodenschutz- und Altlastenverordnung vom 12. Juli 1999 (BGBl. I S. 1554)
Blanchard M, Teil MJ, Ollivon D, Garban B, Chesterikoff C, Chevreuil M (2001) Origin and distribution of polyaromatic hydrocarbons and polychlorobiphenyls in urban effluents to wastewater treatment plants of the Paris area (France). Water Res 35:3679–3687
Blecken GT, Marsalek J, Viklander M (2011) Laboratory study of stormwater biofiltration in low temperatures: total and dissolved metal removals and fates. Water Air Soil Pollut 219(1–4):303–317
Boivin P, Saade M, Pfeiffer HR, Hammecker C, Degoumois Y (2008) Depuration of highway runoff water into grass-covered embankments. Environ Technol 29:709–720
Davis AP, Shokouhian M, Sharma H, Minami C (2001) Laboratory study of biological retention for urban stormwater management. Water Environ Res 73(1):5–14
Davis AP, Shokouhian M, Sharma H, Minami C, Winogradoff D (2003) Water quality improvement through bioretention: lead, copper, and zinc removal. Water Environ Res 75(1):73–82
Davis AP, Shokouhian M, Sharma H, Minami C (2006) Water quality improvement through bioretention media: nitrogen and phosphorus removal. Water Environ Res 78(3):284–293
Delay M, Lager T, Schulz HD, Frimmel FH (2007) Comparison of leaching tests to determine and quantify the release of inorganic contaminants in demolition waste. Waste Manag 27(2):248–255
Dierkes C, Geiger WF (1999) Pollution retention capabilities of roadside soils. Water Sci Technol 39:201–208
Dietz ME (2007) Low impact development practices: a review of current research and recommendations for future directions. Water Air Soil Pollut 186(1–4):351–363
Dietz ME, Clausen JC (2006) Saturation to improve pollutant retention in a rain garden. Environ Sci Technol 40(4):1335–1340
DIN 19682-7 (2015) Soil quality—field tests—part 7: determination of infiltration rate by double ring infiltrometer. German Institute for Standardization, Berlin
DIN 38414-4 (1984) German standard methods for the examination of water, waste water and sludge; sludge and sediments (group S); determination of leachability by water (S4). German Institute for Standardization, Berlin
DWA-A 138 - German Association for Water, Wastewater and Waste (2005) Planung, Bau und Betrieb von Anlagen zur Versickerung von Niederschlagswasser, 2005 [Design, construction and operation of rainwater drainage systems] (in German)
Fletcher TD, Andrieu H, Hamel P (2013) Understanding, management and modelling of urban hydrology and its consequences for receiving waters: a state of the art. Adv Water Resour 51:261–279
Folkeson L, Bækken T, Brenčič M, Dawson A, Frančois D, Kuřímská P, et al. (2009) Sources and fate of water contaminants in roads. In Water in Road Structures. Springer, Netherlands, pp 107–146
García P, Pérez ME, Guerra A (2014) Using TM images to detect soil sealing change in Madrid (Spain). Geoderma 214:135–140
Göbel P, Dierkes C, Coldewey WG (2007) Storm water runoff concentration matrix for urban areas. J Cont Hydrol 91(1):26–42
Hatt BE, Fletcher TD, Deletic A (2008) Hydraulic and pollutant removal performance of fine media stormwater filtration systems. Environ Sci Technol 42(7):2535–2541
He W, Wallinder IO, Leygraf C (2001) A comparison between corrosion rates and runoff rates from new and aged copper and zinc as roofing material. Water Air Soil Pollut Focus 1(3–4):67–82
Hiller D, Winzig G, Dornauf C (2001) Bodenchemische Untersuchungen von Versickerungsanlagen als Grundlage für eine nachhaltige Niederschlagswaserbewirtschaftung im Sinne des Boden- und Grundwasserschutzes. Technical report, Essen (in German)
Hunt WF, Jarrett AR, Smith JT, Sharkey LJ (2006) Evaluating bioretention hydrology and nutrient removal at three field sites in North Carolina. J Irrg Drain E Asce 132(6):600–608
Ingvertsen ST, Cederkvist K, Régent Y, Sommer H, Magid J, Jensen MB (2012a) Assessment of existing roadside swales with engineered filter soil: I. Characterization and lifetime expectancy. J Environ Qual 41(6):1960–1969
Ingvertsen ST, Cederkvist K, Jensen MB, Magid J (2012b) Assessment of existing roadside swales with engineered filter soil: II. Treatment efficiency and in situ mobilization in soil columns. J Environ Qual 41(6):1970–1981
ISO 11466 (1997) Soil quality—extraction of trace elements soluble in aqua regia. German Institute for Standardization, Berlin
ISO 11885 (2007) Water quality—determination of selected elements by inductively coupled plasma optical emission spectrometry (ICP-OES). German Institute for Standardization, Berlin
Jones PS, Davis AP (2013) Spatial accumulation and strength of affiliation of heavy metals in bioretention media. J Environ Eng 139(4):479–487
Kabir MI, Daly E, Maggi F (2014) A review of ion and metal pollutants in urban green water infrastructures. Sci Total Environ 470:695–706
Kayhanian M, Fruchtman BD, Gulliver JS, Montanaro C, Ranieri E, Wuertz S (2012) Review of highway runoff characteristics: comparative analysis and universal implications. Water Res 46:6609–6624
Kluge B, Werkenthin M, Wessolek G (2014) Metal leaching in a highway embankment on field and laboratory scale. Sci Total Environ 493:495–504
Kocher B, Wessolek G, Stoffregen H (2005) Water and heavy metal transport in roadside soils. Pedosphere 15:746–753
LAGA-Bund/Länder-Arbeitsgemeinschaft Abfall (2003) Anforderungen an die stoffliche Verwertung von mineralischen Reststoffen/Abfällen. Technical regulations. (in German)
Le Coustumer S, Fletcher TD, Deletic A, Barraud S, Lewis JF (2009) Hydraulic performance of biofilter systems for stormwater management: influences of design and operation. J Hydrol 376(1):16–23
Le Coustumer S, Fletcher TD, Deletic A, Barraud S, Poelsma P (2012) The influence of design parameters on clogging of stormwater biofilters: a large-scale column study. Water Res 46(20):6743–6752
LeFevre GH, Paus KH, Natarajan P, Gulliver JS, Novak PJ, Hozalski RM (2014) Review of dissolved pollutants in urban storm water and their removal and fate in bioretention cells. J Environ Eng 141(1):04014050
Li H, Davis A (2008a) Urban particle capture in bioretention media. I: laboratory and field studies. J Environ Eng 134(6):409–418
Li H, Davis AP (2008b) Heavy metal capture and accumulation in bioretention media. Environ Sci Technol 42(14):5247–5253
Li H, Davis AP (2009) Water quality improvement through reductions of pollutant loads using bioretention. J Environ Eng 135(8):567–576
Li YL, Deletic A, McCarthy DT (2014) Removal of E. coli from urban stormwater using antimicrobial-modified filter media. J Hazard Mater 271:73–81
Lim HS, Lim W, Hu JY, Ziegler A, Ong SL (2015) Comparison of filter media materials for heavy metal removal from urban stormwater runoff using biofiltration systems. J Environ Manag 147:24–33
Lindsey G, Roberts L, Page W (1992) Inspection and maintenance of infiltration facilities. J Soil and Water Cons 47(6):481–486
Liu J, Sample DJ, Bell C, Guan Y (2014) Review and research needs of bioretention used for the treatment of urban stormwater. Water 6(4):1069–1099
Lucke T, Nichols PW (2015) The pollution removal and stormwater reduction performance of street-side bioretention basins after ten years in operation. Sci Total Environ 536:784–792
Lundy L, Ellis JB, Revitt DM (2012) Risk prioritisation of stormwater pollutant sources. Water Res 46(20):6589–6600
Marsalek J, Watt WE, Anderson BC (2006) Trace metal levels in sediments deposited in urban stormwater management facilities. Water Sci Technol 3(2):175–183
Mullane JM, Flury M, Iqbal H, Freeze PM, Hinman C, Cogger CG, Shi Z (2015) Intermittent rainstorms cause pulses of nitrogen, phosphorus, and copper in leachate from compost in bioretention systems. Sci Total Environ 537:294–303
Parker JK, McIntyre D, Noble RT (2010) Characterizing fecal contamination in stormwater runoff in coastal North Carolina, USA. Water Res 44(14):4186–4194
Paus KH, Morgan J, Gulliver JS, Leiknes T, Hozalski RM (2014) Assessment of the hydraulic and toxic removal capacities of bioretention cells after 2 to 8 years of service. Water Air Soil Pollut 225:1803
Piguet P, Parriaux A, Bensimon M (2008) The diffuse infiltration of road runoff: an environmental improvement. Sci Total Environ 397:13–23
Preciado HF, Li LY (2006) Evaluation of metal loadings and bioavailability in air, water and soil along two highways of British Columbia, Canada. Water Air Soil Pollut 172:81–108
Prince George’s County PGC (2007) Bioretention manual, PGC, Maryland, Dept. of Environmental Resources, Environmental Services Div., Landover, Md
Roy-Poirier A, Champagne P, Filion Y (2010) Review of bioretention system research and design: past, present, and future. J Environ Eng 136(9):878–889
Sauvé S, Hendershot H, Allen HE (2000) Solid-solution partitioning of metals in contaminated soil: dependence on pH, total metal burden, and organic matter. Environ Sci Technol 34:1125–1131
Schöttler U, Remmler F (1999) Abschlußbericht zum BMBF-Vohaben Naturnahe Regenwasserbewirtschaftung aus der Sicht des Boden- und Grundwasserschutzes. Technical report. Institut für Wasserforschung GmbH, Dortmund. (in German)
Søberg L, Blecken GT, Viklander M (2014) The in fluence of temperature and salt on metal and sediment removal in stormwater biofilters. Water Sci Technol 69(11):2295–2223
Trowsdale SA, Simcock R (2011) Urban stormwater treatment using bioretention. J Hydrol 397(3):167–174
Werkenthin M, Kluge B, Wessolek G (2014) Metals in European roadside soils and soil solution—a review. Environ Pollut 189:98–110
Zhang K, Randelovic A, Page D, McCarthy DT, Deletic A (2014) The validation of stormwater biofilters for micropollutant removal using in situ challenge tests. Ecol Eng 67:1–10
Acknowledgments
The authors would like to express their gratitude to the Ministry of North Rhine-Westfalia (MKUNLV NRW) for financial support. We also would like to thank the Berliner Wasserbetriebe (BWB) for supporting the sampling campaign, as well as Wolfgang Burghardt (University of Essen, Germany) for data contribution.
Author information
Authors and Affiliations
Corresponding author
Additional information
Responsible editor: Jianming Xu
Rights and permissions
About this article
Cite this article
Kluge, B., Markert, A., Facklam, M. et al. Metal accumulation and hydraulic performance of bioretention systems after long-term operation. J Soils Sediments 18, 431–441 (2018). https://doi.org/10.1007/s11368-016-1533-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11368-016-1533-z