Abstract
The paper proves the friction law which states that static friction is higher than dynamic friction by proposing the asynchronous rupture of adhesive junction. It is also shown that dynamic friction coefficient is about 0.5–0.67 of static friction coefficient.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
As one of friction laws it states that the static frictional coefficient is higher than the dynamic frictional coefficient. The higher static frictional coefficient is well confused with the fact that friction coefficient increases with the dwell time, which is explained by the growth of adhesion during the static contact in adhesive friction theory. Here, a new mechanism of the static frictional coefficient higher than the dynamic coefficient is proposed based on the tangential deformation of asperities in sliding contact.
2 Asynchronous Rupture of Adhesive Junctions
Surface contact is limited to the local area of asperity peaks which are various both in shape and height. Figure 1 shows the schematic model of the asperity contacts. The tangential force is different at different asperities because the tangential deflection is different. The difference in the tangential force of the different asperities is due to the difference in the contact starting time for the different asperities. We know that the sliding is a dynamic process of rupture of the adhesive junctions and the formation of the adhesive junctions. The tangential force in the contact area is calculated by the following equation of Hertz’s contact [1]:
where \(\mu _\mathrm{{s}}\) is the static frictional coefficient, \(p_{i0}\) the maximum contact pressure, and \(a_\mathrm{{c}}\) the radius of contact area. The contact radius is given by
that is
where \(\nu\) is the Poisson ratio, G the shearing modulus, and R the asperity curvature radius.
The tangential deflection of the contact asperity under the tangential force is given by [1]
The tangential force at the ith contact asperity is given as follows:
Noticing that the contact radius is dependent only on the normal load we know that the tangential force and deflection are proportional to each other in sliding. The total tangential force is the sum of the tangential force at all the contact asperities. This is the static friction. Before the incipient of the rupture of adhesive junctions, the tangential force is less than that given by Eq. (3) and therefore the deflection is also below what is given in Eq. (2). Mindlin [2] gave the following equation before sliding:
For plastic contact we roughly assume that the shear stress \(\tau _\mathrm{{s}}\) is constant in the sliding ring area \(a_\mathrm{{s}} \le \sqrt{\xi ^2+\eta ^2} \le a_\mathrm{{c}}\) , while it is zero in non-sliding areas, and the tangential deflection is still elastic. Then the tangential deflection at the center of contact area is given [1]
which leads to
In macroscopic sliding the contact spots are released and recaptured repeatedly, and/or new contact spots are generated. The ruptures of adhesive junctions on the contact surfaces are asynchronous, which as contrary are synchronous at the incipient of the macroscopic sliding. When the number of deflected junctions are uniformly distributed against the tangential force then the dynamic frictional force is half of the static frictional force. Therefore the dynamic friction coefficient is given by
On the other hand if the distribution is uniform against the tangential deflection, then the dynamic frictional force \(F_\mathrm{{d}}\) is given by
Substituting Eq. (6) into Eq. (9) for elastic contact with rearrangement gives
For plastic contact substituting Eq. (8) into Eq. (9) gives
3 Conclusion
A model of asynchronous rupture of adhesive junctions is proposed, which proves why the static friction is always higher than dynamic friction. The dynamic frictional coefficient is 0.5–0.67 of the static frictional coefficient.
Data Availability
Data sharing is not applicable to this article as no datasets were generated or analyzed during the current study.
References
Johnson, K.L.: Contact Mechanics, p. 74. Cambridge University press, Cambridge (1996)
Mindlin, R.D.: Compliance of elastic bodies in contact. ASME J. Appl. Mech. 16, 259–267 (1949)
Funding
No funding was received to assist with the preparation of this manuscript.
Author information
Authors and Affiliations
Contributions
The paper is completed by BZ.
Corresponding author
Ethics declarations
Competing interest
The authors declare no competing interests.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Zhang, B. Proof of Friction Law: Static Friction is Higher than Dynamic Friction. Tribol Lett 71, 81 (2023). https://doi.org/10.1007/s11249-023-01751-2
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s11249-023-01751-2