Abstract
Recent developments in the fixtureless inspection of non-rigid parts based on computer-aided inspection (CAI) methods significantly contribute to diminishing the time and cost of geometrical dimensioning and inspection. Generally, CAI methods aim to compare scan meshes, which are acquired using scanners as point clouds from non-rigid manufactured parts in a free-state, with associated nominal computer-aided design (CAD) models. However, non-rigid parts are deformed in a free-state due to their compliance behavior. Industrial inspection approaches apply costly and complex physical inspection fixtures to retrieve the functional shape of non-rigid parts in assembly-state. Therefore, fixtureless inspection methods are developed to eliminate the need for these complex fixtures and to replace them with simple inspection supports. Fixtureless inspection methods intend to virtually (numerically) compensate for flexible deformation of non-rigid parts in a free-state. Inspired by industrial inspection techniques wherein weights (e.g., sandbags) are applied as restraining loads on non-rigid parts, we present a new fixtureless inspection method in this article. Our proposed virtual mounting assembly-state inspection (VMASI) method aims at predicting the functional shape (in assembly-state) of a deviated non-rigid part (including defects such as plastic deformation). This method is capable of virtually mounting the scan mesh of a deviated non-rigid part (acquired in a free-state) into the designed assembly-state. This is fulfilled by applying permissible restraining forces (loads) that are introduced as pressures on surfaces of a deviated part. The functional shape is then predicted via a linear FE-based transformation where the value and position of required restraining pressures are assessed by our developed restraining pressures optimization (RPO) approach. In fact, RPO minimizes the orientation difference and distance between assembly mounting holes on the predicted shape of a non-rigid part with respect to nominal ones on the CAD model. Eventually, the inspection is accomplished by examining the mounting holes offset on the predicted shape of the scan model concerning the nominal CAD model. This ensures that the mounting holes on the predicted shape of a scan model in assembly-state remain in the dedicated tolerance range. This method is evaluated on two non-rigid parts to predict the required restraining pressures limited to the permissible forces during the inspection process and to predict the eventual functional shape of the scan model. We applied numerical validations for each part, for which different types of synthetic (numerically simulated) defects are included into scan meshes, to determine whether the functional shape of a geometrically deviated part can be virtually retrieved under assembly constrains.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Abenhaim GN, Desrochers A, Tahan AS, Bigeon J (2015) A virtual fixture using a FE-based transformation model embedded into a constrained optimization for the dimensional inspection of nonrigid parts. Comput Aided Des 62:248–258
Abenhaim GN, Desrochers A, Tahan A (Nov 2012) Nonrigid parts’ specification and inspection methods: notions, challenges, and recent advancements. Int J Adv Manuf Technol 63:741–752
Bi Z, Wang L (2010) Advances in 3D data acquisition and processing for industrial applications. Robot Comput Integr Manuf 26:403–413
Ascione R, Polini W (2010) Measurement of nonrigid freeform surfaces by coordinate measuring machine. Int J Adv Manuf Technol 51:1055–1067
Weckenmann A, Weickmann J (2006) Optical inspection of formed sheet metal parts applying fringe projection systems and virtual fixation. Metrol Meas Syst 13:321–330
Gentilini I, Shimada K (2011) Predicting and evaluating the post-assembly shape of thin-walled components via 3D laser digitization and FEA simulation of the assembly process. Comput Aided Des 43:316–328
Weckenmann A, Weickmann J, Petrovic N (2007) Shortening of inspection processes by virtual reverse deformation. In: 4th international conference and exhibition on design and production of machines and dies/molds, Cesme, Turkey
Jaramillo A, Prieto F, Boulanger P (2013) Fixtureless inspection of deformable parts using partial captures. Int J Precis Eng Manuf 14:77–83
Abenhaim GN, Tahan AS, Desrochers A, Maranzana R, (2011). A novel approach for the inspection of flexible parts without the use of special fixtures. Journal of Manufacturing Science and Engineering, 133(1), p.011009. https://doi.org/10.1115/1.4003335
Aidibe A, Tahan AS, Abenhaim, GN (2012). Distinguishing profile deviations from a part’s deformation using the maximum normed residual test. WSEAS Transactions on Applied and Theoretical Mechanics, 7(1), 18-28
Radvar-Esfahlan H, Tahan S-A (2012) Nonrigid geometric metrology using generalized numerical inspection fixtures. Precis Eng 36:1–9
Sabri V, Tahan SA, Pham XT, Moreau D, Galibois S (2016) Fixtureless profile inspection of non-rigid parts using the numerical inspection fixture with improved definition of displacement boundary conditions. Int J Adv Manuf Technol 82:1343–1352
Sattarpanah Karganroudi S, Cuillière J-C, Francois V, Tahan S-A (2016) Automatic fixtureless inspection of non-rigid parts based on filtering registration points. Int J Adv Manuf Technol:1–26
Merkley, K. G. (1998). Tolerance analysis of compliant assemblies (Doctoral dissertation, Brigham Young University).
Mounaud M, Thiebaut F, Bourdet P, Falgarone H, Chevassus N (2011) Assembly sequence influence on geometric deviations propagation of compliant parts. Int J Prod Res 49:1021–1043
Chen H, Jin S, Li Z, Lai X (2014) A comprehensive study of three dimensional tolerance analysis methods. Comput Aided Des 53:1–13
Ravishankar S, Dutt H, Gurumoorthy B (2010) Automated inspection of aircraft parts using a modified ICP algorithm. Int J Adv Manuf Technol 46:227–236
Weckenmann A, Gall P, Hoffmann J (2004). Inspection of holes in sheet metal using optical measuring systems. In Proceedings of VIth International Science Conference Coordinate Measuring Technique (April 21-24, 2004, Bielsko-Biala, Poland), pp. 339-346
Bronstein AM, Bronstein MM, Kimmel R (2006) Generalized multidimensional scaling: a framework for isometry-invariant partial matching. Proc Natl Acad Sci U S A 103:1168–1172
Kimmel R, Sethian JA (1998) Computing geodesic paths on manifolds. Proc Natl Acad Sci 95:8431–8435
Spence AD, Chan H-L, Mitchell JP, Capson DW (2005) Automotive sheet metal and grid digitizing solutions. Comput Aided Des Appl 2:135–144
Botsch M, Pauly M (2007). Course 23: Geometric modeling based on polygonal meshes. In International Conference on Computer Graphics and Interactive Techniques: ACM SIGGRAPH 2007 courses: San Diego, California (Vol. 2007)
Frey PJ, George PL (2008). Mesh generation: application to finite elements. London: ISTE
Cuillière JC, Francois V (2014) Integration of CAD, FEA and topology optimization through a unified topological model. Comput Aided Des Appl 11:1–15
Geuzaine C, Remacle J-F (2009) Gmsh: a three-dimensional finite element mesh generator with built-in pre- and post-processing facilities. Int J Numer Methods Eng 79:1309–1331
Acknowledgments
In this paper, we use Gmsh™ [25] for visualizing distance distributions.
Funding
The authors would like to thank the National Sciences and Engineering Research Council of Canada (NSERC), industrial partners, Consortium for Aerospace Research and Innovation in Québec (CRIAQ) and UQTR foundation for their support and financial contribution.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Sattarpanah Karganroudi, S., Cuillière, JC., François, V. et al. “What-if” scenarios towards virtual assembly-state mounting for non-rigid parts inspection using permissible loads. Int J Adv Manuf Technol 97, 353–373 (2018). https://doi.org/10.1007/s00170-018-1947-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-1947-4