Abstract
A new method of optimization on the hot forging tools for connecting rods was developed in this paper by combining response surface analysis (RSA) with finite element method (FEM). The central composite design (CCD) was prepared with three experimental factors and two optimal targets. The experimental factors which are extracted from design dimensions of the hot forging tool involve cavity center distance, cavity rotation angle, and flash thickness. The targets comprise the maximum forming load and tool wear depth, both of which can be obtained from finite element simulations of hot forging processes. Response surface analysis was implemented to establish the relationships between the targets and the factors. According to the simulation results, the S-type region between die cavities that was dominated by three factors has a significant impact on the metal flowing and forming defects during the hot forging process. The steel billet and forging tools were dimensionally redesigned based on the optimal combination of experimental factors. Practice forging and physical experiments were performed to verify the simulation results, and good agreement between experimental value and simulation value was obtained.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Whittaker D (2001) The competition for automotive connecting rod markets. Met Powder Rep 56(5):32–37
Wang Q, He F (2004) A review of developments in the forging of connecting rods in China. J Mater Process Technol 151(1–3):192–195
Bramley AN, Mynors D (2000) The use of forging simulation tools. Mater Des 21(4):279–286
Biba N, Stebounov S, Lishiny A (2001) Cost effective implementation of forging simulation. J Mater Process Technol 113(1):34–39
Hatzenbichler T, Harrer O, Buchmayr B (2006) State of development and benefit from FEM-simulation of bulk forming processes. BHM Berg- Hüttenmaenn Monatsh 151(11):469–474
Hartley P, Pillinger I (2006) Numerical simulation of the forging process. Comput Method Appl M 195(48–49):6676–6690
Satish GD, Singh NK, Ohdar RK (2008) Preform optimization of pad section of front axle beam using DEFORM. J Mater Process Technol 203(1–3):102–106
Zhang ZJ, Dai GZ, Wu SN, Dong LX, Liu LL (2009) Simulation of 42CrMo steel billet upsetting and its defects analyses during forming process based on the software DEFORM-3D. Mater Sci Eng A 499(1–2):49–52
Gronostajski Z, Kaszuba M, Polak S, Zwierzchowski M, Niechajowicz A, Hawryluk M (2016) The failure mechanisms of hot forging dies. Mater Sci Eng A 657:147–160
Takemasu T, Vazquez V, Painter B, Altan T (1996) Investigation of metal flow and preform optimization in flashless forging of a connecting rod. J Mater Process Technol 59(1):95–105
Bariani PF, Bruschi S (2005) Modelling the forging and post-forging cooling of C70S6 conrods. J Mater Process Technol 167(2–3):529–535
Grass H, Krempaszky C, Werner E (2006) 3-D FEM-simulation of hot forming processes for the production of a connecting rod. Comput Mater Sci 36(4):480–489
Hatzenbichler T, Buchmayr B (2008) Preform optimisation for closed-die forging by numerical simulation. BHM Berg- Hüttenmaenn Monatsh 153(11):413–417
Behrens BA (2008) Finite element analysis of die wear in hot forging processes. CIRP Ann 57(1):305–308
Yilmaz NF, Eyercioglu O (2008) An integrated computer-aided decision support system for die stresses and dimensional accuracy of precision forging dies. Int J Adv Manuf Technol 40(9–10):875–886
Wang M, Xiang D, Xiao C, Zhou J, Jia Z (2011) Influence of cooling condition of tools on central deformation of workpiece and tool wear in cross wedge rolling. Int J Adv Manuf Technol 59(5–8):473–482
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Liu, Y., Wang, J. & Wang, D. Numerical optimization on hot forging process of connecting rods based on RSA with experimental verification. Int J Adv Manuf Technol 90, 3129–3135 (2017). https://doi.org/10.1007/s00170-016-9635-8
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-9635-8