Abstract
Friction stir welding (FSW) has emerged as an attractive process for fabricating aerospace vehicles. Current FSW state-of-the-art uses large machines that are not portable. However, there is a growing need for fabrication and repair operations associated with in-space manufacturing. This need stems from a desire for prolonged missions and travel beyond low-earth orbit. To address this need, research and development is presented regarding two enabling technologies. The first is a self-adjusting and aligning (SAA) FSW tool that drastically reduces the axial force that has historically been quite large. The SAA-FSW tool is a bobbin style tool that floats freely, without any external actuators, along its vertical axis to adjust and align with the workpiece’s position and orientation. Successful butt welding of 1/8 in. (3.175 mm) thick aluminum 1100 was achieved in conjunction with a drastic reduction and near elimination of the axial process force. Along with the SAA-FSW, an innovative in-process monitor technique is presented in which a magnetoelastic force rate-of-change sensor is employed. The sensor consists of a magnetized FSW tool that is used to induce a voltage in a coil surrounding the tool when changes to the process forces occur. The sensor was able to detect 1/16 in. (1.5875 mm) diameter voids. It is concluded that these technologies could be applied toward the development of a portable FSW machine for use in space.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Materials, Structures, Mechanical Systems, and Manufacturing Roadmap, Technology Area 12, NASA 2010. http:www.nasa.gov (accessed 2016)
Thomas W, Nicolas E, Needham J, et al. Friction stir butt welding. Patent 5,460,317, USA, 24 October 1995
Wikipedia. http://en.wikipedia.org/wiki/Friction_stir_welding (accessed 2013).
Longhurst WR, Strauss AM, Cook GE (2011) The identification of the key enablers for force control of robotic friction stir welding. Journal of Manufacturing Science and Engineering: AMSE 133(3):31008–31019
Soron M. and Kalaykov I., A robot prototype for friction stir welding, Proceedings of the 2006 I.E. Conference on Robotics, Automation and Mechatronics, Bangkok, Thailand, 7–9 June 2006, pp. 1–5. New York: IEEE.
Smith C., Robotic friction stir welding using a standard industrial robot. Proceedings of the 2nd Friction Stir Welding International Symposium, Gothenburg June 27–29, 2000. Cambridge: The Welding Institute, 2000.
Cook G, Crawford R, Clark D, Strauss A (2004) Robotic friction stir welding, industrial. Robot 31(1):55–63
Crawford R, Cook G, Strauss A, Hartman D (2006) Modelling of friction stir welding for robotic implementation. Int J Model Identif Control 1(2):101–106
Sinclair P, Longhurst WR, Cox CD, Lammlein DH, Strauss AM, Cook GE (2010) Heated friction stir welding: an experimental and theoretical investigation into how preheating influences process forces. Mater Manuf Process 25(11):1283–1291
Fuller, C. B., Friction stir tooling: tool materials and design. In: Mishra, R. S., Mahoney, M. W. (Eds.) Friction stir welding and processing, chapter 2. Materials Park, OH: Editors: ASM International, 2007, pages 7–35.
Sued M, Pons D, Lavroff J, Wong E (2014) Design features for bobbin friction stir welding tools: development of a conceptual model linking the underlying physics to the production process. Mater Des 54:632–643
Colligan, K. J., O’Donnell, A. K., Shevock, J. W., Smitherman, M. T., Friction stir welding of thin aluminum using fixed gap bobbin tools. 9th International FSW Symposium, Huntsville Alabama, May 15–17, 2012.
Ding, R. J., Oelgoetz, P. A., Autoadjustable pin tool for friction stir welding. U.S. Patent 5893501, April 13, 1999.
Davé, V. R., Hartman, D. A., King, W. H., Cola, M. J., & Vaidya, R. U., Strategy for small-lot manufacturing. Los Alamos Science, Number 28, 2003.
Longhurst WR, Cox CD, Gibson BT, Cook GE, Strauss AM (2014) Applied torque control of friction stir welding using motor current as feedback. Proceedings of the Institution of Mechanical Engineers, Part B. Journal of Engineering Manufacturing 228(8):947–958
Garshelis, I. J., Kari, R. J., Tollens, S. P. L., Cuseo, J. M., Monitoring cutting tool operation and condition with a magnetoelastic rate of change of torque sensor. Journal of Applied Physics, Volume 103, Issue 07E908, 2008.
Longhurst, W. R., Wilbur, I. C., Osborne, B. E., Gaither, B. W., Process monitoring of friction stir welding via the frequency of the spindle motor current. Proceedings of the Institution of Mechanical Engineers, Part B, Journal of Engineering Manufacturing, Accepted May 19, 2016, Available Online DOI: 10.1177/0954405416654089.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Longhurst, W.R., Cox, C.D., Gibson, B.T. et al. Development of friction stir welding technologies for in-space manufacturing. Int J Adv Manuf Technol 90, 81–91 (2017). https://doi.org/10.1007/s00170-016-9362-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-9362-1