Abstract
The stress–strain state in chip is investigated by the finite-element method. In addition, the cutting process and the mechanics of chip formation are studied experimentally over the whole temperature range of metal cutting.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Grigor’ev, S.N., Metody povysheniya stoikosti rezhushchego instrumenta: uchebnik dlya studentov vuzov (Strength Improvement of Cutting Tool: Manual for Higher Education Students), Moscow: Mashinostroenie, 2011.
Artamonov, E.V., Vasilega, D.S., Ostapenko, M.S., et al., Rabotosposobnost’ instrumentov i fiziko-mekhanicheskie kharakteristiki instrumental’nykh tverdykh splavov i obrabatyvaemykh materialov: monografiya (Efficiency of Tools and Physical-Mechanical Characteristics of Hard Alloys for Tools and Processed Materials: Monograph), Uteshev, M.Kh., Ed., Tyumen: Vektor Buk, 2008.
Poduraev, V.N., Rezanie trudnoobrabatyvaemykh materialov: uchebnoe posobie dlya vuzov (Cutting of Hard Materials: Manual for Higher Education Institutions), Moscow: Vysshaya Shkola, 1974.
Artamonov, E.V. and Vasil’ev, D.V., Determining the optimal cutting speed in turning by composite cutters on the basis of the chip, Russ. Eng. Res., 2014, vol. 34, no. 6, pp. 404–405.
Poletika, M.F., Teoriya rezaniya. Chast’ 1. Mekhanika protsessa rezaniya. Uchebnoe posobie (The Cutting Theory, Part 1: Mechanics of Cutting: Manual), Tomsk: Tomsk. Politekh. Univ., 2001.
Bobrov, V.F. and Sedel’nikov, A.I., Specific formation of joint and element chips at the high cutting speed, Vestn. Mashinostr., 1976, no. 7, pp. 61–66.
Vasin, S.A., Vereshchaka, A.S., and Kushner, V.S., Rezanie materialov: Termomekhanicheskii podkhod k sisteme vzaimosvyazei pri rezanii: uchebnik dlya tekhnicheskikh vuzov (Cutting of Materials: Thermomechanical Approach to the Interaction Systems during Cutting: Manual for Technical Higher Education Institutions), Moscow: Mosk. Gos. Tekh. Univ. im. N.E. Baumana, 2001.
Krivoukhov, V.A., Petrukha, P.G., Brushtein, B.E., et al., Rezanie konstruktsionnykh materialov: rezhushchie instrumenty i stanki (Cutting of Construction Materials: Cutting Tools and Machines), Petrukha, P.G., Ed., Moscow: Mashinostroenie, 1974.
Lasukow, A.A., Chazov, P.A., and Barsuk, A.V., Investigation on the elemental chip formation process in hard-to-machine material cutting, Appl. Mech. Mater., 2014, vol. 682, pp. 504–509.
Artamonov E.V. and Kireev V.V. Effectiveness of cutting by hoods with replaceable hard-alloy plates, Russ. Eng. Res., 2014, vol. 34, no. 7, pp. 473–474.
Yamnikov, A.S. and Myagkov, Yu.V., Determination of the minimum specific normal force required for cutting start, Izv. Vyssh. Uchebn. Zaved., Mashinostr., 1979, no. 12, p.111.
Drachev, A.O., Drachev, O.I., Taranenko, G.V., et al., Thermopower treatment of stepped axisymmetric parts, Mater. mezhdunarodnoi nauchno-tekh. konferentsii “Avtomatizatsiya: problemy, idei, resheniya” (Proc. Int. Sci.-Tech. Conf. “Automation: Problems, Concepts, and Solutions”), Sevastopol: Sevastop. Nats. Tekh. Univ., 2009, pp. 18–21.
Pustovalov, D.A., Mokritskii, B.Ya., Shpilev, A.M., Vysotskii, V.V., Sablin, P.A., and Prikhodchenko, O.V., Efficiency of metal-cutting tool for processing of materials used in chemical and oil and gas machine engineering, Vestn. Mashinostr., 2013, no. 6, pp. 46–52.
Petrakov, Yu.V. and Drachev, O.I., Modelirovanie protsessov rezaniya: uchebnoe posobie (Modeling of Cutting Processes: Manual), Staryi Oskol: TNT, 2011.
Artamonov, E.V., Pomigalova, T.E., and Uteshev, M.Kh., Raschet i proektirovanie smennykh rezhushchikh platin i sbornykh instrumentov (Design of Replaceable Polyhedral Plates and Composite Tools), Tyumen: Tyumen. Gos. Neftegaz. Univ., 2011.
Okoshi, M., Research on the cutting force, in Scientific Papers of the Institute of Physical and Chemical Research, Tokyo, 1930, vol. 14, pp. 193–225.
Rozenberg, Yu.A., Analytical evaluation of the deformation degree of the chip metal during cutting, Vestn. Mashinostr., 2001, no. 3, pp. 34–38.
Author information
Authors and Affiliations
Corresponding author
Additional information
Original Russian Text © E.V. Artamonov, D.V. Vasil’ev, V.V. Kireev, M.Kh. Uteshev, 2016, published in STIN, 2016, No. 11, pp. 24–28.
About this article
Cite this article
Artamonov, E.V., Vasil’ev, D.V., Kireev, V.V. et al. Mechanics of chip formation in cutting. Russ. Engin. Res. 37, 450–454 (2017). https://doi.org/10.3103/S1068798X17050069
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X17050069