Abstract
This paper describes the effect of thermal exposure (high-temperature exposure) (T = 675◦C) on the residual creep stress relaxation in a surface hardened solid cylindrical sample made of ZhS6UVI alloy. The analysis is carried out with the use of experimental data for residual stresses after micro-shot peening and exposures to temperatures equal to T = 675◦C during 50, 150, and 300 h. The paper presents the technique for solving the boundary-value creep problem for the hardened cylindrical sample with the initial stress–strain state under the condition of thermal exposure. The uniaxial experimental creep curves obtained under constant stresses of 500, 530, 570, and 600 MPa are used to construct the models describing the primary and secondary stages of creep. The calculated and experimental data for the longitudinal (axial) tensor components of residual stresses are compared, and their satisfactory agreement is determined.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
I. A. Birger, Residual Stresses (Mashgiz, Moscow, 1963) [in Russian].
V. F. Pavlov, V. A. Kirpichev, and V. B. Ivanova, Residual Stresses and Fatigue Resistance of Reinforced Parts with Stress Concentrators (Samara Scientific Center, Russian Acad. of Sci., Samara, 2008) [in Russian].
I. G. Grinchenko, Reinforcement of Parts of Heat-Resistant And Titanium Alloys (Mashinostroenie, Moscow, 1971) [in Russian].
B. A. Kravchenko, V. G. Krutsilo, and G. N. Gutman, Thermoplastic Reinforcement—Strength and Reliability Enhancement for Machine Parts (Samara State University, Samara, 2000) [in Russian].
A. M. Sulima, V. A. Shuvalov, and Yu. D. Yagodkin, The Surface Layer and Performance of GTE (Mashinostroenie, Moscow, 1988) [in Russian].
V. P. Radchenko and M. N. Saushkin, Creep and Relaxation of Residual Stresses in Reinforced Structures, (Mashinostroenie-1, Moscow, 2005) [in Russian].
I. Altenberger, R. K. Nalla, Y. Sano, et al., “On the Effect of Deep-Rolling and Laser-Peening on the Stress-Controlled Low- and High-Cycle Fatigue Behavior of Ti-6-Al-4V at Elevated Temperatures up to 550°C,” Int. J. Fatigue 44, 292–302 (2012).
R. A. Brockman, W. R. Braisted, S. E. Olson, et al., “Prediction and Characterization of Residual Stresses from Laser Shock Peening,” Int. J. Fatigue 36 (1), 96–108 (2012).
K. Dai and L. Shaw, “Analysis of Fatigue Resistance Improvements via Surface Severe Plastic Deformation,” Int. J. Fatigue 30 (8), 1398–1408 (2008).
M. N. James, D. J. Hughes, Z. Chen, et al., “Residual Stresses and Fatigue Performance,” Eng. Failfure Anal. 14 (20), 384–395 (2007).
G. H. Majzoobi, K. Azadikhah, and J. Nemati, “The Effects of Deep Rolling and Shot Peening on Fretting Fatigue Resistance of Aluminum-7075-T6,” Mater. Sci. Eng. 516 (1/2), 235–247 (2009).
R. C. McClung, “A Literature Survey on the Stability and Significance of Residual Stresses during Fatigue,” Fatigue Fract. Eng. Mater. Struct. 30 (3), 173–205 (2007).
K. A. Soady, “Life Assessment Methodologies Incorporating Shot Peening Process Effects: Mechanistic Consideration of Residual Stresses and Strain Hardening. 1. Effect of Shot Peening on Fatigue Resistance,” Mater. Sci. Technol. 29 (6), 637–651 (2013).
M. A. Terres, N. Laalai, and H. Sidhom, “Effect of Nitriding and Shot-Peening on the Fatigue Behavior of 42CrMo4 Steel: Experimental Analysis and Predictive Approach,” Mater. Design 35, 741–748 (2012).
V. F. Pavlov, “On the Relationship between the Residual Stress and Fatigue Strength at a Bend in the Conditions of Stress Concentration,” Izv. Vyssh. Uchebn. Zaved., Mashinostroenie, No. 8, 29–32 (1986).
V. P. Radchenko and O. S. Afanas’eva, “Technique for Calculating the Fatigue Limit of Reinforced Cylindrical Samples with Stress Concentrators at Temperature Exposure,” Vesnt. Samar. Gos. Tekh. Univ., Ser. Fiz.-Mat. Nauki, No. 2, 264–268 (2009).
V. F. Pavlov, V. A. Kirpichev, and V. S. Vakulyuk, Prediction of Fatigue Strength of Surface Hardened Details Based on the Residual Stresses (Izd. Samar. Nauch. Tsentra Ross. Akad. Nauk, Samara, 2012) [in Russian].
V. F. Pavlov, V. A. Kirpichev, and V. A. Lunin, “Impact on Thermal Exposition on Residual Stresses of the EP742 Sample Alloys after Ultrasonic Hardening,” Vestn. Samar. Gos. Univ., Tekh. Univ., Ser. Tekh. Nauki, No. 3, 147–154 (2012).
V. I. Tseitlin and O. V. Kolotnikova, “Fatigue of Residual Stresses in the GTE Turbine Details in the Process of Operation,” Probl. Prochnosti, No. 8, 982–984 (1980).
D. J. Buchanan and R. John, “Relaxation of Shot-Peened Residual Stresses under Creep Loading,” Scripta Mater. 59 (3), 286–289 (2008).
Xie Lechun, Jiang Chuanhai, and Ji Vincent, “Thermal Relaxation of Residual Stresses in Shot Peened Surface Layer of (TiB+TiC)/Ti-6Al-4V Composite at Elevated Temperatures,” Mater. Sci. Eng. A. 528 (21), 6478–6489 (2011).
B. J. Foss, S. Gray, M. C. Hardy, et al., “Analysis of Shot-Peening and Residual Stress Relaxation in the Nickel-Based Superalloy RR1000,” Acta Mater. 61 (7), 2548–2559 (2013).
V. P. Radchenko, V. A. Kirpichev, and V. A. Lunin, “Impact of Air-Shot Peening and Thermal Exposition on Residual Stresses and Strength Limit of V95 and D16T Alloy Samples,” Vestn. Samar. Gos. Tekh. Univ., Ser. Fiz.-Mat. Nauki, No. 3, 181–184 (2011).
J. Hoffmann, B. Scholtes, O. Vohringer, et al., “Thermal Relaxation of Shot Peening Residual Stresses in the Differently Heat Treated Plain Carbon Steel Ck 45,” Shot Peening: Sci., Technol., Appl. 61 (7), 360–367 (1987).
M. Khadraoui, W. Cao, and L. Castex, “Experimental Investigations and Modelling of Relaxation Behaviour of Shot Peening Residual Stresses at High Temperature for Nickel Base Superalloys,” Mater. Sci. Technol. 13 (4), 360–367 (1997).
A. Evans, S-B. Kim, J. Shackleton, et al., “Relaxation of Residual Stress in Shot Peened Idimet 720Li under High Temperature Isothermal Fatigue,” Int. J. Fatigue. 27 (10), 1530–1534 (2005).
M. Benedetti, V. Fontanari, P. Scardi, et al., “Reverse Bending Fatigue of Shot Peened 7075-T651 Aluminium Alloy: The Role of Residual Stress Relaxation,” Int. J. Fatigue 31 (8/9), 1225–1236 (2009).
Kim Jong-Cheon, Cheong Seong-Kyun, and Noguchi Hirochi, “Residual Stress Relaxation and Low- and High-Cycle Fatigue Behavior of Shot-Peened Medium-Carbon Steel,” Int. J. Fatigue 56, 114–122 (2013).
O. V. Kolotnikova, “Effectiveness of the Methods of Hardening by Surface Plastic Strain of Parts Operating at High Temperatures,” Probl. Prochnosti, No. 2, 112–114 (1983).
V. P. Radchenko, A. P. Morozov, and V. A. Lunin, “Study on the Kinetics of Physical and Mechanical Parameters of B95 and D16T Alloys Due to Temperature Exposures and Multicycle Fatigue Tests,” Vestnik. Samar. Gos. Tekh. Univ., Ser. Fiz.-Mat. Nauki, No. 1, 123–132 (2012).
V. P. Radchenko and M. N. Saushkin, “Direct Method of Solving the Boundary-Value Problem of Relaxation of Residual Stresses in a Hardened Cylindrical Specimen under Creep Conditions,” Prikl. Mekh. Tekh. Fiz. 50 (6), 90–99 (2009) [J. Appl. Mech. Tech. Phys. 50 (6), 989–997 (2009)].
V. P. Radchenko and V. V. Tsvetkov, “The Kinetics of a stress–strain State in a Surface Hardened Cylindrical Sample in a Complex Stress State in Creep,” Vestnik. Samar. Gos. Tekh. Univ., Ser. Fiz.-Mat. Nauki, No. 1, 93–108 (2014).
M. N. Saushkin, V. P. Radchenko, and V. F. Pavlov, “Method of Calculating the Fields of Residual Stresses and Plastic Strains in Cylindrical Specimens with Allowance for Surface Hardening Anisotropy,” Prikl. Mekh. Tekh. Fiz. 52 (2), 173–182 (2011) [J. Appl. Mech. Tech. Phys. 52 (2), 303–310 (2011)].
Yu. P. Samarin, Equation of State of Materials with Complicated Rheological Properties (Kuybyshev State University, Kuybyshev, 1979) [in Russian].
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 57, No. 3, pp. 196–207, May–June, 2016.
Rights and permissions
About this article
Cite this article
Radchenko, V.P., Saushkin, M.N. & Tsvetkov, V.V. Effect of thermal exposure on the residual stress relaxation in a hardened cylindrical sample under creep conditions. J Appl Mech Tech Phy 57, 559–568 (2016). https://doi.org/10.1134/S0021894416030202
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S0021894416030202