Abstract
Quality control at every stage of manufacturing is a key aspect of the quality management system of any organization. Inspection at different stages of manufacturing is essential to achieve required quality of the product. This knowledge area has been studied extensively in the past with respect to inspection strategies, inspection location, and inspection intervals to minimize inspection cost. However, there is a lack of literature that examines the relationship between inspection performance and factors related to human labor and inspection time of different products. Here, offline inspection is investigated to achieve the process target values by determining the optimal number of inspectors for different products. Three skill levels for inspectors are selected on the basis of their inspection errors, inspection quantities, and inspection cost. The purpose of this study is to achieve the optimum results of objective functions that consist of inspection cost, outgoing quality, and inspection quantity by determining the optimal value of decision variables, i.e., the number of inspectors with respect to their skill. A multi-objective optimization model is developed using a stochastic approach to determine the optimal results of the objective functions and decision variables. Firstly, goal programming is employed to verify the optimization model by using numerical examples. Secondly, sensitivity analysis is considered to illustrate the effect of incoming quantity on inspection performance and optimal combination of decision variables.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Ramzan MB, Kang CW (2016) Minimization of inspection cost by determining the optimal number of quality inspectors in the garment industry. Indian J Fibre Text Res 41(3):346–350
Cheng K, Bateman RJ (2008) e-Manufacturing: characteristics, applications and potentials. Prog Nat Sci 18 (11):1323–1328
Rodger JA (2014) Application of a fuzzy feasibility Bayesian probabilistic estimation of supply chain backorder aging, unfilled backorders, and customer wait time using stochastic simulation with Markov blankets. Expert Syst Appl 41(16):7005–7022
Tzimerman A, Herer YT (2009) Off-line inspections under inspection errors. IIE Trans 41(7):626–641
Tirkel I, Rabinowitz G (2012) The relationship between yield and flow time in a production system under inspection. Int J Prod Res 50(14):3686–3697. https://doi.org/10.1080/002075 43.2011.575099
Tirkel I, Rabinowitz G (2014) Modeling cost benefit analysis of inspection in a production line. Int J Prod Econ 147:38–45. https://doi.org/10.1016/j.ijpe.2013.05.012
Ramzan MB, Chang W, Sarkar B (2016) A review paper on offline inspection of finished and semi-finished products and emerging research directions. Yugoslav J Oper Res 26(4)
Duffuaa SO, Khan M (2008) A general repeat inspection plan for dependent multicharacteristic critical components. Eur J Oper Res 191(2):374–385
Duffuaa SO, Khan M (2005) Impact of inspection errors on the performance measures of a general repeat inspection plan. Int J Prod Res 43(23):4945–4967. https://doi.org/10.1080/00207540 412331325413
Elshafei M, Khan M, Duffuaa S (2006) Repeat inspection planning using dynamic programming. Int J Prod Res 44 (2):257–270
Yang M (2010) Minimization of inspection cost in an inspection system considering the effect of lot formation on AOQ. Int J Manag Sci 16(1):119–135
Yang MH, Cho JH (2014) Minimisation of inspection and rework cost in a BLU factory considering imperfect inspection. Int J Prod Res 52(2):384–396
Montgomery DC (2009) Introduction to statistical process control6th edn. John Wiley & Sons, Inc., Hoboken
Yu H-F, Yu W-C, Wu WP (2009) A mixed inspection policy for CSP-1 and precise inspection under inspection errors and return cost. Comput Ind Eng 57(3):652–659
Yu H-F, Yu W-C (2011) A joint inspection policy between CSP-1 and precise inspection for non-repairable products under inspection errors and return cost. J Qual 18(1):61–73
Anily S, Grosfeld-Nir A (2006) An optimal lot-sizing and offline inspection policy in the case of nonrigid demand. Oper Res 54(2):311–323
Wang C-H, Meng F-C (2009) Optimal lot size and offline inspection policy. Comput Math Appl 58(10):1921–1929
Vaghefi A, Sarhangian V (2009) Contribution of simulation to the optimization of inspection plans for multi-stage manufacturing systems. Comput Ind Eng 57(4):1226–1234
Avinadav T, Perlman Y (2013) Economic design of offline inspections for a batch production process. Int J Prod Res 51(11):3372–3384. https://doi.org/10.1080/00207543.2013.774478
Raz T, Herer YT, Grosfeld-Nir A (2000) Economic optimization of off-line inspection. IIE Trans 32(3):205–217. https://doi.org/10.1023/A:1007690329729
Wang W-Y, Sheu S-H, Chen Y-C, Horng D-J (2009) Economic optimization of off-line inspection with rework consideration. Eur J Oper Res 194(3):807–813
Bendavid I, Herer YT (2009) Economic optimization of off-line inspection in a process that also produces non-conforming units when in control and conforming units when out of control. Eur J Oper Res 195(1):139–155. https://doi.org/10.1016/j.ejor.2008.01.026
Wang C-H, Hung C-C (2008) An offline inspection and disposition model incorporating discrete Weibull distribution and manufacturing variation. J Oper Res Soc Jpn 51(2):155–165
Wang C-H (2007) Economic off-line quality control strategy with two types of inspection errors. Eur J Oper Res 179(1):132–147
Finkelshtein A, Herer YT, Raz T, Ben-Gal I (2005) Economic optimization of off-line inspection in a process subject to failure and recovery. IIE Trans 37(11):995–1009. https://doi.org/10.1080/07408170500232149
Tsai WC, Wang CH (2011) Economic optimization for an off-line inspection, disposition and rework model. Comput Ind Eng 61(3):891–896. https://doi.org/10.1016/j.Cie.2011.04.011
Duffuaa SO, El-Ga'aly A (2013) A multi-objective mathematical optimization model for process targeting using 100% inspection policy. Appl Math Model 37(3):1545–1552. https://doi.org/10.1016/j.apm.2012.04.008
Duffuaa SO, El-Ga'aly A (2015) Impact of inspection errors on the formulation of a multi-objective optimization process targeting model under inspection sampling plan. Comput Ind Eng 80:254–260. https://doi.org/10.1016/j.cie.2014.07.025
Duffuaa SO, El-Ga'aly A (2013) A multi-objective optimization model for process targeting using sampling plans. Comput Ind Eng 64(1):309–317. https://doi.org/10.1016/j.cie. 2012.10.001
Duffuaa S, El Gaaly A (2017) A multi-objective optimization model for process targeting with inspection errors using 100% inspection. Int J Adv Manuf Technol 88(9–12):2679–2692
Grosfeld-Nir A, Cohen E, Gerchak Y (2007) Production to order and off-line inspection when the production process is partially observable. Nav Res Logist 54(8):845–858
Colledani M, Tolio T (2009) Performance evaluation of production systems monitored by statistical process control and off-line inspections. Int J Prod Econ 120(2):348–367. https://doi.org/10.1016/j.ijpe.2007.07.011
Khan M, Jaber M, Wahab M (2010) Economic order quantity model for items with imperfect quality with learning in inspection. Int J Prod Econ 124(1):87–96
Khan M, Jaber MY, Bonney M (2011) An economic order quantity (EOQ) for items with imperfect quality and inspection errors. Int J Prod Econ 133(1):113–118
Khan M, Jaber M, Guiffrida A (2012) The effect of human factors on the performance of a two level supply chain. Int J Prod Res 50(2):517–533
Galindo-Pacheco GM, Paternina-Arboleda CD, Barbosa-Correa RA, Llinás-Solano H (2012) Non–linear programming model for cost minimisation in a supply chain, including non–quality and inspection costs. Int J Oper Res 14 (3):301–323
Avinadav T, Sarne D (2012) Sequencing counts: a combined approach for sequencing and selecting costly unreliable off-line inspections. Comput Oper Res 39(11):2488–2499. https://doi.org/10.1016/j.cor.2011.12.018
Bouslah B, Gharbi A, Pellerin R (2014) Joint production and quality control of unreliable batch manufacturing systems with rectifying inspection. Int J Prod Res 52(14):4103–4117
Khan M, Jaber MY, Ahmad A-R (2014) An integrated supply chain model with errors in quality inspection and learning in production. Omega 42(1):16–24
Liu S-W, Lin S-W, Wu C-W (2014) A resubmitted sampling scheme by variables inspection for controlling lot fraction nonconforming. Int J Prod Res 52(12):3744–3754
Aslam M, Wu C-W, Azam M, Jun C-H (2014) Mixed acceptance sampling plans for product inspection using process capability index. Qual Eng 26(4):450–459
Mohammadi M, Siadat A, Dantan J-Y, Tavakkoli-Moghaddam R (2015) Mathematical modelling of a robust inspection process plan: Taguchi and Monte Carlo methods. Int J Prod Res 53(7):2202–2224
Sarkar B, Saren S (2016) Product inspection policy for an imperfect production system with inspection errors and warranty cost. Eur J Oper Res 248(1):263–271
Sardar S, Lee YH (2014) Analysis of product complexity considering disruption cost in fast fashion supply chain. Math Probl Eng. 2014, Article ID 670831, p15 https://doi.org/10.1155/2014/670831
Ullah M, Kang CW (2014) Effect of rework, rejects and inspection on lot size with work-in-process inventory. Int J Prod Res 52(8):2448–2460
Sett BK, Sarkar S, Sarkar B (2017) Optimal buffer inventory and inspection errors in an imperfect production system with preventive maintenance. Int J Adv Manuf Technol 90(1–4):545–560
Sarkar B, Cárdenas-Barrón LE, Sarkar M, Singgih ML (2014) An economic production quantity model with random defective rate, rework process and backorders for a single stage production system. J Manuf Syst 33(3):423–435
Arizono I, Okada Y, Tomohiro R, Takemoto Y (2016) Rectifying inspection for acceptable quality loss limit based on variable repetitive group sampling plan. Int J Adv Manuf Technol 85(9–12):2413–2423
Cheikhrouhou N, Sarkar B, Ganguly B, Malik AI, Batista R, Lee YH (2017) Optimization of sample size and order size in an inventory model with quality inspection and return of defective items. Ann Oper Res. p 1–23 https://doi.org/10.1007/s10479-017-2511-6
Choudhary D, Shankar R (2014) A goal programming model for joint decision making of inventory lot-size, supplier selection and carrier selection. Comput Ind Eng 71:1–9
Sharma JK (2000) Operations research: theory and applications. 5th edn. Macmillan, Delhi
Taha HA (2007) Operations research: an introduction. 8th edn. Pearson Prentice Hall, New Jersey
Jaber MY (2016) Learning curves: theory, models, and applications. CRC Press
Acknowledgements
This research was supported by Research Fund of Hanyang University (HY-2016-G).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Kang, C.W., Ramzan, M.B., Sarkar, B. et al. Effect of inspection performance in smart manufacturing system based on human quality control system. Int J Adv Manuf Technol 94, 4351–4364 (2018). https://doi.org/10.1007/s00170-017-1069-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-1069-4