Abstract
Fabrication of miniaturized components provides a challenge to the manufacturing industries and to meet the challenges many unconventional machining methods are developed, among which laser beam micromachining (LBμM) is one. But, thermal effects such as recast layer, heat-affected zone (HAZ), debris, and thermal cracks are commonly observed in LBμM. So, in order to minimize the thermal effects, underwater laser beam micromachining (UW-LBμM) came into existence. In this paper, experiment on UW-LBμM is reported using a Q-switched Nd:YAG laser for fabricating microchannels on 304 stainless steel. The effect of input process parameters (scanning speed, number of scan, laser pulse energy) on output responses (kerf width, kerf depth, surface roughness) of microchannel is studied. Laser micromachined channels are characterized by using optical microscopy, surface profilometer, scanning electron microscopy, and energy dispersive X-ray spectroscopy. It is observed that the dimensions of kerf width and kerf depth are low at lower number of scan, laser pulse energy, and higher scanning speed. The surface roughness decreases with decrease in number of scan and increase in laser pulse energy. Minimum surface roughness is achieved at scanning speed of 300 μm/s. The recast layer and debris are minimum during UW-LBμM compared to LBμM. Elemental comparison is carried out inside and in the surroundings of microchannel.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Dahotre NB, Harimkar SP (2008) Laser micromachining. Laser fabrication and machining of materials. Springer, pp 247–288
Ghoshal B, Bhattacharyya B (2015) Generation of microfeatures on stainless steel by electrochemical micromachining. Int J Adv Manuf Technol 76:39–50
Im H, Oh KH, Kim SG, Jeong S (2009) Application of etchant jet for laser micromachining of metal channels. Int J Precis Eng Manuf 10(4):101–105
Kannatey E (2009) Principles of laser materials processing. Wiley, Hoboken
Khalil AAI, Sreenivasan N (2005) Study of experimental and numerical simulation of laser ablation in stainless steel. Laser Physics Letter 2(9):445–451
Raval A, Choubey A, Engineer C, Kothwala D (2004) Development and assessment of 316LVM cardiovascular stents. Mater Sci Eng A 386:331–343
Leone C, Genna S, Caprino G, De Iorio I (2010) AISI 304 stainless steel marking by a Q-switched diode pumped Nd:YAG laser. J Mater Process Technol 210:1297–1303
Ahn D, Seo C, Park T, Park D, Park S, Kwon Y, Kim D (2014) Micromachining of stainless steel–polymer composites using nanosecond and femtosecond UV lasers. Int J Adv Manuf Technol 74:1691–1699
Akhtar SN, Choudhary H, Ramakrishna SA, Ramkumar J (2014) Simulations and experiments on excimer laser micromachining of metal and polymer. Journal of Micro/Nanolithography, MEMS, and MOEMS 13(1):013008(1–9)
Chen K, Yao YL (2000) Process optimization in pulsed laser micromachining with applications in medical device manufacturing. Int J Adv Manuf Technol 16:243–249
Voisey K et al (2003) Melt ejection during laser drilling of metals. Mater Sci Eng A 356(1):414–424
Zoppel S, Farsari M, Merz R, Zehetner J, Stangl G, Reider GA, Fotakis C (2006) Laser micro machining of 3C–SiC single crystals. Microelectron Eng 83:1400–1402
Ghoreishi M, Low D, Li L (2002) Comparative statistical analysis of hole taper and circularity in laser percussion drilling. Int J Mach Tool Manufact 42(9):985–995
Sezer HK, Li L, Schmidt M, Pinkerton AJ, Anderson B, Williams P (2006) Effect of beam angle on HAZ, recast and oxide layer characteristics in laser drilling of TBC nickel superalloys. Int J Mach Tool Manufact 46(15):1972–1982
Miller P, Aggarwal R, Doraiswamy A, Lin YJ, Lee YS, Narayan RJ (2009) Laser micromachining for biomedical applications. J Miner Met Mater Soc 61:35–40
Pecholt B, Vendan M, Dong Y, Molian P (2007) Ultra laser micromachining of 3C–SiC thin films for MEMS device fabrication. Int J Mach Tool Manufact 39:239–250
Muhammad N, Li L (2012) Underwater femtosecond laser micromachining of thin nitinol tubes for medical coronary stent manufacture. App Phys A 107:849–861
Muhammad N, Whitehead D, Boor A, Li L (2010) Comparison of dry and wet fibre laser profile cutting of thin 316L stainless steel tubes for medical device applications. J Mater Process Technol 210:2261–2267
Wee LM, Khoong LE, Tan CW, Lim GC (2011) Solvent-assisted laser drilling of silicon carbide. Int J Appl Ceram Technol 8(6):1263–1276
An R, Li Y, Dou Y, Liu D, Yang H, Gong (2006) Water-assisted drilling of microfluidic chambers inside silica glass with femtosecond laser pulses. App Phys A 83:27–29
Karimzadeh R, Anvari JZ, Mansour N (2009) Nanosecond pulsed laser ablation of silicon in liquids. App Phys A 94:949–955
Prakash S, Acherjee B, Kuar AS, Mitra S (2013) An experimental investigation on Nd:YAG laser microchanneling on polymethyl methacrylate submerged in water. Proc IMechE B J Eng Manuf 227(4):508–519
Yan Y, Li L, Sezer K, Wang W, Whitehead D, Ji L, Bao Y, Jiang Y (2011) CO2 laser underwater machining of deep cavities in alumina. J Eur Ceram Soc 31:2793–2807
Mullick S, Madhukar YK, Kumar S, Shukla DK, Nath AK (2011) Temperature and intensity dependence of Yb-fiber laser light absorption in water. Appl Opt 50:6319–6326
Porter JA, Louhisalmi YA, Karjalainen JA, Füger S (2007) Cutting thin sheet metal with a water jet guided laser using various cutting distances, feed speeds and angles of incidence. Int J Adv Manuf Technol 33:961–967
Knowles MRH, Rutterford G, Karnakis D, Ferguson A (2007) Micro-machining of metals, ceramics and polymers using nanosecond lasers. Int J Adv Manuf Technol 33:95–102
Kruusing A (2004) Underwater and water-assisted laser processing: part 1—general features, steam cleaning and shock processing. Opt Laser Eng 41:307–327
Kruusing A (2004) Underwater and water-assisted laser processing: part 2—Etching, cutting and rarely used methods. Opt Laser Eng 41:329–352
Lu J, Xu RQ, Chen X, Shen ZH, Ni XW, Zhang SY, Gao CM (2004) Mechanisms of laser drilling of metal plates underwater. J Appl Phys 95(8):3890–3894
Chung CK, Lin SL (2010) CO2 laser micromachined crack less through holes of Pyrex 7740 glass. Int J Mach Tool Manufact 50:50961–50968
Nath AK, Hansdah D, Roy S, Choudhury AR (2010) A study on laser drilling of thin steel sheet in air and underwater. J Appl Phys 107(12):123103(1–9)
Mak GY, Lam EY, Choi HW (2011) Liquid-immersion laser micromachining of GaN grown on sapphire. App Phys A 102:441–447
Krstulovic N, Shannon S, Stefanuik R, Fanara C (2013) Underwater-laser drilling of aluminum. Int J Adv Manuf Technol 69:1765–1773
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Behera, R.R., Sankar, M.R., Swaminathan, J. et al. Experimental investigation of underwater laser beam micromachining (UW-LBμM) on 304 stainless steel. Int J Adv Manuf Technol 85, 1969–1982 (2016). https://doi.org/10.1007/s00170-016-8635-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-8635-z