Abstract
Titanium is a potential material for MEMS and biomedical uses owing to its unique high strength to weight ratio and their excellent corrosion resistance property. Machining of titanium by conventional as well as non-conventional methods is a challenge due to its inherent mechanical and chemical properties. Machining of titanium in micro domain is a topic of great research interest. Electrochemical micromachining (EMM) technique could be possible alternative for machining of titanium especially in micro domain. This paper presents systematic investigation of suitability of electrolyte for anodic dissolution of titanium through electrochemical micromachining. In order to investigate the performance of electrolytes, seven different types of electrolytes have been selected. The nature of dissolution of titanium and influence of electrolyte has been studied by machining a set of through micro holes in pure commercial titanium with all these different types of electrolytes. Five electrolytes out of seven have been demonstrated successful anodic dissolution of titanium using EMM process parameters. Out of these five electrolytes, two non-aqueous electrolytes were further evaluated, based on various criteria, i.e. material removal rate, radial overcut and conicity of micro hole. Amongst the two non-aqueous electrolytes, electrolyte with combination of ethylene glycol and sodium bromide has demonstrated excellent results during titanium micromachining by EMM.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Ezugwu EO, Wang ZM (1997) Titanium alloys and their machinability—a review. J Mater Process Technol 68:262–274
Kumar Jatinder, Khamba JS, Mohapatra SK (2008) An investigation into the machining characteristics of titanium using ultrasonic machining. Int. J. Mach Mach Mater 3:Nos. 1/2
Lin YC, Yan BH, Chang YS (2000) Machining characteristics of titanium alloy (Ti6Al4V) using a combination process of EDM with USM. J Mater Process Technol 104:171–177
Jain VK, Kalia S, Sidpara A, Kulkarni VN (2012) Fabrication of micro-features and micro-tools using electrochemical micromachining. Int J Adv Manuf Technol 61:1175–1183
Lee ES, Baek SY, Cho CR (2007) A study of the characteristics for electrochemical micromachining with ultrashort voltage pulses. Int J Adv Manuf Technol 31:762–769
Bhattacharyya B, Malapati M, Munda J (2005) Experimental study on electrochemical micromachining. J Mater Process Technol 169:485–492
Aladjem A (1973) Anodic oxidation of titanium and its alloys. J Mater Sci 8:688–704
Bannard J (1976) On the electrochemical machining of some titanium alloys in bromide electrolytes. J Appl Electrochem 6:477–483
Madore C, Landolt D (1997) Electrochemical micromachining of controlled topographies on titanium for biological applications. J Micromech Microeng 7:270–275
Piotrowski O, Madore C, Landolt D (1998) The mechanism of electropolishing of titanium in methanol-sulfuric acid electrolytes. J Electrochem Soc 145:7, The Electrochemical Society, Inc
Landolt D, Chauvy PF, Zinger O (2003) Electrochemical micromachining, polishing and surface structuring of metals: fundamental aspects and new developments. Electrochim Acta 48:3185–3201
Zinger O, Chauvy PF, Landolt D (2003) Scale-resolved electrochemical surface structuring of titanium for biological applications. J Electrochem Soc 150(11):B495–B503
Kern P, Vehand J, Michler J (2007) New developments in through-mask electrochemical micromachining of titanium. J Micromech Microeng 17:1168–1177
Jiang LM, Li W, Attia A, Cheng ZY, Tang J, Tian ZQ, Tian ZW (2008) A potential method for electrochemical micromachining of titanium alloy Ti6Al4V. J Appl Electrochem 38:785–791
Lu X, Leng Y (2005) Electrochemical micromachining of titanium surfaces for biomedical applications. J Mater Process Technol 169:173–178
Koji F, Hiroki H (2008) Anodic dissolution of titanium in NaCl containing ethylene glycol. Elechtrochim Acta 53:3371–3376
Sjöström T, Bo S (2011) Micropatterning of titanium surfaces using electrochemical micromachining with an ethylene glycol electrolyte. Mater Lett 65:3489–3492
Dhobe SD, Doloi B, Bhattacharyya B (2011) Surface characteristics of ECMed titanium work samples for biomedical applications. Int J Adv Manuf Technol 55:177–188
Cotton FA, Wilkinson G, Murillo CA, Bochmann M (1999) Advanced inorganic chemistry, 6th edn. Wiley, New York
Clifton J, Mount AR, Jardine DJ, Roth R (2001) Electrochemical machining of gamma titanium aluminide in intermettallics. J Mater Process Technol 108:338–348
McGeough JA (1974) Principles of electrochemical machining. Chapman and Hall
Fushimi K, Kondo H, Konno H (2009) Anodic dissolution of titanium in chloride-containing ethylene glycol solution. Electrochim Acta 55:258–264
Mohan S, Shan HS (2005) A review of electrochemical macro- to micro-hole drilling processes. Intl J Mach Tools Manuf 45:137–152
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Anasane, S.S., Bhattacharyya, B. Experimental investigation on suitability of electrolytes for electrochemical micromachining of titanium. Int J Adv Manuf Technol 86, 2147–2160 (2016). https://doi.org/10.1007/s00170-015-8309-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-8309-2