Abstract
Properties of laser radiation and photons are firstly introduced. Planck´s law, Stefan-Boltzmann’s law and Wien´s law are then presented. Spontaneous emission, stimulated absorption, stimulated emission, Einstein coefficients are explained, leading to the definition of important parameters such as laser gain and stimulated emission cross section. Upper level laser rate equation, light increment along an active medium and laser oscillation threshold condition are consequently defined. More importantly, laser rate equation involving a laser resonant cavity is presented, allowing laser photon density calculation within the resonant cavity. Solar concentration ratio, transfer efficiency, absorption efficiency, upper state efficiency, beam overlap efficiency and output coupling efficiency are also explained. A modified analytical method for solar laser power calculation is consequently put forward. Solar laser output power are finally calculated by the modified, classical, Zemax® and LASCAD™ analysis methods.
Access provided by Autonomous University of Puebla. Download chapter PDF
Similar content being viewed by others
3.1 Brief Introduction
Properties of laser radiation and photons are firstly introduced. To comprehend solar irradiance and solar-pumped solid-state laser theory, Planck’s law, Stefan-Boltzmann’s law and Wien’s law are presented and reinforced by several homework with solutions. The concept of spontaneous emission, stimulated absorption, stimulated emission, Einstein coefficients and thermodynamic treatment are then explained, leading to the definition of important parameters such as photon degeneracy, laser gain and stimulated emission cross section. Upper level laser rate equation, light increment along an active medium and laser oscillation threshold condition are consequently defined. More importantly, laser rate equation involving a laser resonant cavity is presented, permitting laser photon density calculation within the resonant cavity. To calculate solar laser output power, important definitions like solar concentration ratio, transfer efficiency, absorption efficiency, upper state efficiency, beam overlap efficiency and output coupling efficiency are explained. With the help of Zemax® software, the deviation angles and the effective absorption length of a solar pump ray within a laser rod are determined. A simplified Nd:YAG absorption spectrum is also provided, facilitating considerably the calculation of absorbed solar power density and absorbed pump photon number density within five simplified absorption bands of the Nd:YAG medium. Consequently, a modified analytical method for solar laser power calculation is put forward. Solar laser power from both a side-pumped laser and an end-side-pumped laser are finally calculated by the modified, classical, Zemax® and LASCAD™ analysis methods. In this chapter, we shall outline the basic theory underlying the operation of solar-pumped solid-state lasers. In-depth treatments of laser physics can be found in a number of excellent textbooks [1,2,3,4,5,6].
3.2 Properties of Laser Radiation
Laser radiation is characterized by an extremely high degree of directionality, monochromaticity, coherence, and brightness.
3.2.1 Directionality
Laser emits a well-defined beam in a specific direction, which implies laser light is of very small divergence. This is a direct consequence of the fact that a laser beam comes from a resonant cavity, and only waves propagating along the optical axis can be sustained in the cavity. The direction of the beam is governed by the orientation of the mirrors in the cavity. The directionality is described by the light beam divergence angle. For perfect spatial coherent light, a beam of aperture diameter \(D\) will have unavoidable divergence because of diffraction. From diffraction theory, the divergence angle \(\theta_{d }\) is given by
where \(\lambda\) and \(D\) are the wavelength and the diameter of the beam respectively. \(\beta\) is a coefficient whose value is around unity and depends on the type of light amplitude distribution and the definition of beam diameter. \(\theta_{d }\) is defined as diffraction limited divergence.
For a Nd:YAG laser beam with: \(\lambda = 1.06\;\upmu {\text{m}},D = 3\;{\text{mm}},\beta = 1.1\), \(\theta_{d } = \frac{\beta \lambda }{D} = 0.02227{ }^{^\circ }\).
Therefore, a laser beam provides a Very Low Beam Divergence.
Consequently, a laser beam ensures a Very High Focusability.
A fundamental mode laser beam can be focused to a diffraction-limited spot size [7] (Fig. 3.1).
According to (3.2), for a collimated beam, the diffraction-limited focal spot size \(2 w_{f}\) of a laser beam depends on its wavelength \(\lambda\), the size of the parallel beam \(2 w_{0}\) at the focusing lens and the focal length \(f\) of that lens.
3.2.2 Monochromaticity
Monochromaticity refers to a pure spectral color of a single wavelength. A laser cavity forms a resonant system. The photons are emitted by the stimulated emission where all the photons are in the same phase and in the same state of polarization. Oscillations can sustain only at the resonance frequency of the cavity. This leads to the narrowing of the laser line width. So, the laser light is usually very pure in wavelength, and the laser is therefore said to have the property of monochromaticity. In situations where only a single resonator mode has sufficient laser gain to oscillate, a single longitudinal mode can be selected, obtaining single-frequency operation. For a laser beam with υ0 = 5 × 1014 Hz (yellow color), typical value of ∆υ = 1 kHz − 1 MHz can be achieved by a gas laser. Using additional techniques for stabilizing the frequency, the linewidth can be further reduced by a massive extent. Some laser systems serve as optical frequency standards with a linewidth below 1 Hz [8], attaining an elevated spectral purity of \(10^{ - 15}\).
Quality factor of monochromaticity is defined as:
3.2.3 Coherence
A very important characteristic of laser light is coherence. Coherence means that light waves are in phase. Lasers have a high degree of both spatial and temporal coherence.
Spatial coherence—for light impinging on a surface, the light is coherent if the waves (or photons) at any two points selected at random on the plane maintain a constant phase difference over time.
Temporal coherence characterizes how well a wave can interfere with itself at two different times and increases as a source becomes more monochromatic (Fig. 3.2).
Definition of coherence length
Coherence length is defined as
The coherence length Lc is the coherence time Δt times the vacuum velocity of light c, and thus also characterizes the temporal coherence via the propagation length over which coherence is lost.
Since Δυ ≃ 1/∆t, coherence length can also be presented as
Relations between \(\Delta {\varvec{t}}\,{\mathbf{and}}\,{{\varvec{\Delta}}}{{\varvec{\upsilon}}}\)
The temporal coherence \(\Delta {\text{t}}\) comes from the monochromaticity of a laser beam. The narrower the line width \(\Delta\upupsilon\) of the light source, the better is its temporal coherence \(\Delta {\text{t}}\).
Relation between \({\Delta }{\varvec{\lambda}}\,{\mathbf{and}}\,{\Delta}{{\varvec{\upsilon}}}\)
Since \(\lambda = { }\frac{c}{{\upupsilon }}\),
We obtain the relationship between \({\Delta }\lambda\) and \(\Delta{\upsilon }\)
Based on (3.9), the quality factor of coherence and monocromaticity is defined
Finally, we can deduce the relations between coherence length \(L_{c}\) and central wavelength λ with linewidth ∆λ.
Example 1
(Homework) For a He–Ne gas laser with λ = 630 nm central wavelength and ∆λ = 0.002 nm linewidth.
For a Nd:YAG solid-state laser with λ = 1064 nm central wavelength and ∆λ = 5 nm linewidth.
Consequently, the coherence length and coherence quality factor of a He–Ne gas laser with λ = 630 nm central wavelength and ∆λ = 0.002 nm linewidth are about 880, 1480 times higher than that of a Nd:YAG solid-sate laser with λ = 1064 nm central wavelength and ∆λ = 5.0 nm linewidth, respectively.
3.2.4 High Brightness
While summing up the above descriptions of directionality (low divergence angle \(\Delta \Omega\)) and consequently focusability (small focal spot area \(\Delta s\)), as well as monochromaticity (narrow line width \(\Delta \nu\)) of a laser beam, its brightness cannot be missed out, which is defined as the power emitted per unit surface area per unit frequency and per solid angle, as indicated by (3.12). The units are watts per square meter per unit frequency and per Steradian.
where:
- \(B_{\upsilon }\):
-
is defined as laser beam brightness.
- \(P\):
-
is the laser beam power contained within \(\Delta s\), \(\Delta \upsilon\) and \(\Delta \Omega\).
- \(\Delta s\):
-
is source area, which is related to laser beam focusability.
- \(\Delta \nu\):
-
is frequency band width, which is related to laser beam monochromaticity.
- \(\Delta \Omega\):
-
is solid angle, which is related to laser beam directionality.
Since a laser beam is featured by an excellent focusablity, monochromaticity and directionality, \(\Delta s\), \(\Delta \nu\), \(\Delta \Omega\) are substantially smaller than that of classical light source such as lamps, offering therefore unprecedented laser beam brightness.
TEM00-mode laser beam brightness can also be easily defined
where
- \(B_{\upsilon }\):
-
represents TEM00-mode laser beam brightness.
- \(P\):
-
denotes laser power.
- A:
-
is beam cross-section area.
- \(\Delta \upsilon_{0}\):
-
is laser linewidth.
- \(\theta_{0}\):
-
is beam divergence angle in the far field.
3.3 Photons
3.3.1 Concept and Properties of Photon
Photons are fundamental subatomic particles that carry the electromagnetic force. As quanta of light, photons are the smallest possible packets of electromagnetic energy. Photons are integer spin-1 \(( \pm \hbar )\) particles (making them bosons) and does not obey the Pauli Exclusion Principle like other half-integer spin-1/2 \(( \pm \hbar /2)\) fermions (electrons, protons and neutrons), but obeys the Bose–Einstein statistics.
Photons have no electric charge or rest mass. Thereore, photons are electrically neutral and are not deflected by electric and magnetic fields. Photon travels at the speed of light in empty space (c = 2.998 × 108 m/s). However, in the presence of matter, a photon can be slowed or even absorbed, transferring energy momentum proportional to its frequency. Like all quanta, the photon has both wave and particle properties; it exhibits wave—particle duality. Today, the role of the photon as a carrier of energy is perhaps its most important attribute. The light coming from the Sun has different wavelengths or energy and on the basis of it, we have different regions like visible, infrared, ultraviolet and many more. But one thing is common in all these regions is photon, but of different frequency and so different energy.
Photons are emitted in many natural processes, e.g., when a charge is accelerated, when an atom or a nucleus jumps from a higher to lower energy level, or when a particle and its antiparticle are annihilated (for example, electron–positron annihilation). Photons are absorbed in the time-reversed processes which correspond to those mentioned above. Photons can have particle-like interactions (i.e. collisions) with electrons and other particles, such as in the Compton Effect in which particles of light collide with atoms, causing the release of electrons.
3.3.2 Photon Energy
Each photon has a definite energy depending upon the frequency \(\upsilon\) of the incident radiation and not on its intensity. If the intensity of light of a given wavelength is increased, there is an increase in the number of photons emitted by the incident radiations on a given area in a given time. But the energy of each photon remains unchanged.
where h = 6.626 × 10–34 J s is Planck’s constant, c = 2.998 × 108 m/s is the speed of light and \(\lambda\) is the wavelength of light. All photons travel at the speed of light. The energy of a photon depends on radiation frequency; there are photons of all energies from high-energy gamma and X-rays, through visible light, to low-energy infrared and radio waves. The photon energy is inversely proportional to the wavelength of the electromagnetic wave. The shorter the wavelength, the more energetic is the photon. The longer the wavelength, the less energetic is the photon.
3.3.3 Photon Momentum
There is a relationship between photon energy \(E\) and photon momentum \(p\) and that is consistent with the relation for the relativistic total energy of a particle
We know \(m\) is zero for a photon, but \(p\) is not, so that (3.15) becomes
The momentum of a photon is related to its wavelength \(\lambda\) and can be calculated using the following formula
Photons carry linear momentum and spin angular momentum when circularly or elliptically polarized. During light—matter interaction, transfer of linear momentum leads to optical forces, whereas transfer of angular momentum induces optical torque. Optical forces including radiation pressure and gradient forces have long been used in optical tweezers and laser cooling. Space sails have been proposed that use the momentum of sunlight reflecting from gigantic low-mass sails to propel spacecraft in the solar system.
3.4 Blackbody Radiation—Planck’ Law
The term blackbody comes from a theoretical model of an object absorbing all incident radiation, as shown in Fig. 3.3a that is used to develop the quantum mechanics equations. The radiated energy can be considered to be produced by standing wave or resonant modes of the cavity which is radiating. It turns out that all objects behaves like blackbodies, regardless if they are actually black or not, as shown in Fig. 3.3b.
To explain the spectral-energy distribution of radiation emitted by a blackbody, Max Planck put forward the concept of quantification of radiation energy. Energy emitted by a resonator of frequency could only take on discrete values or quanta. Planck contributed to the advancement of physics by his discovery of “Quanta”.
According to Plank, for each frequency \(\upsilon\) (each mode) → it has the energy U
For frequency interval, \(\upupsilon \leftrightarrow\upupsilon + {\text{d}}\upupsilon\).
The number of radiation modes within a blackbody cavity can be calculated (See homework with solution 1)
Consequently, the energy density \(\rho \left( \nu \right)\) in frequency interval \(\upupsilon \leftrightarrow\upupsilon + {\text{d}}\upsilon\) can be calculated
When electromagnetic radiation in a cavity is in thermal equilibrium at the absolute temperature \(T\), Planck hence formulated the theory of spectral distribution of thermal radiation
Planck’s law for the energy radiated \(\rho \left( \upsilon \right)\) per unit volume by a cavity of a blackbody in the frequency interval \(\nu\) to \(\nu + \Delta \nu\) (Δ\(\nu\) denotes an increment of frequency) can be written in terms of Planck’s constant (h = 6.626 × 10–34 J s), the speed of light \(\left( {C = 2.998 \times 10^{8} \;{\text{m}}\;{\text{s}}^{ - 1} } \right)\), the Boltzmann constant \(\left( {\kappa = 1.3806 \times 10^{ - 23}\; {\text{J}}\;{\text{k}}^{ - 1} } \right)\), and the absolute temperature (T).
3.5 Solar Spectral Irradiance from Planck’s Formula
In experimental work, blackbody radiation distribution according to wavelength is much more preferred.
We can deduce the spectral density \(\rho \left( \lambda \right)\) in (3.22) from \(\rho \left( \upsilon \right)\) in (3.21). (See homework with solution 2).
Solar spectral irradiance \(I\left( \lambda \right)\; {\text{in W m}}^{ - 2} {\text{nm}}^{ - 1}\) can be obtained by multiplying spectral energy density \(\rho \left( \lambda \right)\) by light velocity \(c\).
Equation (3.24) denotes the power emitted at a given wavelength per unit solid angle (one Steradian), per unit area (Fig. 3.4).
3.6 Stefan-Boltzmann’s Law
The total radiant flux \(I,\) in unit [\({\text{W}}\,{\text{m}}^{ - 2} = {\text{J}}\,{\text{m}}^{ - 2} {\text{s}}^{ - 1}\)], emitted from the surface of a black body at temperature \(T\) is expressed by the Stefan-Boltzmann law:
where \(\sigma\) denotes a fundamental physical constant called the Stefan-Boltzmann constant, \(\sigma\) equals to \({ }5.67 \times 10^{ - 8} \;{\text{w}}/{\text{m}}^{2} {\text{K}}^{4}\). \(\varepsilon\) is the emissivity of the blackbody \(\left( {\varepsilon \le 1} \right).\)
Total radiation energy density can be obtained by integrating the energy density ρ(\(\nu\), T) over all wavelengths \(\lambda\). (See homework with solution 3).
Stefan-Boltzmann’s law gives the radiant intensity of a single object. By Stefan-Boltzmann’s law, we can also determine the radiation heat transfer between two objects. Two bodies that radiate toward each other have a net radiant power between them, as given by (3.26).
The area factor A1-2 is the area viewed by body 2 of body 1. In many cases, body 1 can be surrounded by body 2, as shown by Fig. 3.5.
3.7 Wien’s Displacement Law
Wien’s displacement law is a law of physics that states that there is an inverse relationship between the wavelength of the peak of the emission of a black body and its temperature. The spectral radiance of black body radiation per unit wavelength \(\rho \left( {\lambda ,T} \right)\) peaks at the wavelength λmax, as given by (3.27)
where \(T\) is the absolute temperature in Kelvins, \(b\) is a constant of proportionality, known as Wien’s displacement constant, which equals to \(2.898 \times 10^{ - 3}\; {\text{m}}\;{\text{K}}\).
By taking derivative of Eq. (3.24) versus wavelength \(\lambda ,\) the peak \(\rho \left( \lambda \right)\) of blackbody distribution curve can be found at \(\lambda_{{{\text{max}}}}\) (See homework with solution 4).
Example 2
(Homework)
Calculation of different peak wavelengths for different blackbody temperatures by (3.27).
Human body: T = 310 K → Answer (λmax = 9.35 μm).
Molten iron: T = 1810 K → Answer (λmax = 1.60 μm).
The Sun: T = 5800 K → Answer (λmax = 500 nm).
3.8 Spontaneous Emission, Stimulated Absorption and Simulated Emission Probabilities
In the early twentieth century, Max Planck formulated the theory of spectral distribution of thermal radiation. Albert Einstein, by combining Planck’s theory and the Boltzmann statistics gave a theory of stimulated emission which is the governing principle of lasers. Let us assume that the material is placed in a blackbody cavity whose walls are kept at a constant temperature \(T\). Once thermodynamic equilibrium is reached, energy density with a spectral distribution \(\rho \left( \upsilon \right)\) will be established and the material will be immersed in this radiation. In this material, both stimulated-emission and absorption processes will occur, in addition to the spontaneous-emission process. There are three ways in which an incident radiation can interact with the energy levels of atoms.
To describe the phenomenon of spontaneous emission, stimulated absorption and radiations, let us consider two energy levels, lower level 1 and upper level 2, of some atom or molecule of a given material, their energies being E1 and E2 (E1 < E2) (Fig. 3.6). It is important to note that the two levels could be any two out of the infinite set of levels possessed by the atom.
3.8.1 Spontaneous Emission Probability
Atoms which are in excited states are not in thermal equilibrium with their surroundings. Such atoms will eventually return to their ground state by emission of a photon. The population of the upper level will decrease due to spontaneous transition to the lower level with emission of radiation. The rate of emission will depend on the population of the upper level. Spontaneous emission is a statistical function of space and time. With a large number of spontaneously emitting atoms, there is no phase relationship between the individual emission processes; the quanta emitted are incoherent. Spontaneous emission probability \(A_{21}\) is only related to the properties of the atom itself and does not depend on with the radiation field \(\rho \left( \upsilon \right)\) (Fig. 3.7).
Definition of spontaneous emission probability \(A_{21}\)
Equation (3.28) has a solution:
where \(\tau_{s}\) is the lifetime for spontaneous radiation of level 2. This radiation lifetime is equal to the reciprocal of the Einstein’s coefficient.
Unit \(A \left[ \frac{1}{\text{s}} \right] = \frac{1}{{230\;\upmu {\text{s}}}}\) for Nd:YAG medium.
3.8.2 Stimulated Absorption Probability
In the presence of an electromagnetic field, an atom in a lower level can undergo transitions to the upper level provided that the frequency of the radiation field \(\user2{ }\rho \left( \upsilon \right)\) satisfies (3.31), (Fig. 3.8).
However, this process is not a spontaneous one, because the atom is “stimulated to absorb” by the incident light field \(\rho \left( \upsilon \right)\), \(W_{12}\) is the stimulated absorption probability of radiation, as defined below
Unit \(W_{12} \left[ \frac{1}{\text{s}} \right]\).
Dimensional analysis \(W_{12} \left[ \frac{1}{\text{s}} \right] = B_{12} \rho \left( \upsilon \right)\; \left[ {\frac{{{\text{m}}^{3} }}{{{\text{J}} \cdot {\text{s}}^{2} }}} \right] \left[ { \frac{{{\text{J}} \cdot {\text{s}}}}{{{\text{m}}^{3} }} } \right]\).
Absorption pump probability \(W_{12}\) is related not only to Einstein absorption constant \(B_{12}\) but energy density of radiation \(\rho \left( \upsilon \right)\) as well.
3.8.3 Stimulated Emission Probability
In 1917, Einstein showed that under certain conditions, emission of light may be stimulated by radiation incident on an excited atom. This happens when an electron is in an excited state and a photon whose energy is equal to the difference between and the energy of upper and lower energy levels. The incident photon induces the electron in the excited state to make a transition to the lower level by emission of a photon. The emitted photon travels in the same direction as the incident photon. Significantly, the new photon has the same energy as that of the incident photon and is perfectly in phase with it. When a sizable population of electrons resides in upper levels, this condition is called a “population inversion”, and it sets the stage for stimulated emission of multiple photons. This is the precondition for the light amplification which occurs in a laser, and since the emitted photons have a definite time and phase relation to each other, the light has a high degree of coherence (Fig. 3.9).
\(W_{21}\) is the stimulated emission probability, as defined below:
Unit \(W_{21} \left[ \frac{1}{\text{s}} \right]\).
Dimensional analysis \(W_{21} \left[ \frac{1}{\text{s}} \right] = B_{21} \rho \left( \upsilon \right) \left[ {\frac{{{\text{m}}^{3} }}{{{\text{J}} \cdot {\text{s}}^{2} }}} \right]\left[ { \frac{{{\text{J}} \cdot {\text{s}}}}{{{\text{m}}^{3} }} } \right]\).
Stimulated emission probability \(W_{12}\) is related not only to Einstein emission constant \(B_{21}\) but energy density of radiation \(\rho (\upsilon )\) as well.
3.9 Einstein’s Relations
Although Einstein coefficients A21, B12, and B21 are associated to different transition processes, they are all directly related to each other. If we know one of them, we can work out the rest.
Laser rate equation of upper level
Under steady state of transition
Therefore
From Boltzmann equation
By inserting (3.39) into (3.38)
By comparing (3.40) with Planck’s formula (3.21),
We can finally find the relations of Einstein coefficients A21, B12, and B21.
3.10 Photon Degeneracy in Light from Laser
From Planck’s blackbody formula
We obtain
From Einstein relation
We obtain
Photon degeneracy \(\overline{n}\) is finally deduced [9]
where
-
\(W_{21} = \frac{{\left( {\frac{{dn_{21} }}{dt}} \right)_{st} }}{{n_{2} }} = B_{21} \rho \left( \upsilon \right)\) denotes stimulated emission probability (3.34).
-
\(A_{21} = \frac{{\left( {\frac{{dn_{21} }}{dt}} \right)_{st} }}{{n_{2} }}\) denotes spontaneous emission probability (3.28).
To attain laser radiation, stimulated emisssion probability should be higher than spontaneous emission probability W21 > A21, or photon degeneracy should be more than unity, \(\overline{n} \ge 1\).
Example 3
(Homework)
Calculation of photon degeneracy for \(\lambda = 0.6\;\upmu {\text{m}}\) visible lightwave at different temperatures by
-
1.
\(T = 300\;{\text{K}}\), \(\lambda = 0.6\;\upmu {\text{m}}\)
(Answer \(\overline{n} = 10^{ - 35}\)), not possible for laser emission.
-
2.
\(T = 5000\;K\), \(\lambda = 0.6\;\upmu {\text{m}}\)
(Answer \(\overline{n} = 0.08\)), not possible for laser emission.
-
3.
\(T = 50000\;K\), \(\lambda = 0.6\;\upmu {\text{m}}\)
(Answer \(\overline{n} = 1.54\)), possible for laser emission.
Example 4
(Homework)
Calculation of photon degeneracy for \(\lambda = 30\;{\text{cm}}\) microwave radiation at \(T = 300\;K\).
Answer:
Conclusion
As shown by example 3, stimulated emission process may be significant for optical frequencies, but this requires extremely high temperature \(\left( {T = 50000\;{\text{K}}} \right)\) to attain the minimum laser emission condition.
W21 > A21, or photon degeneracy should be more than one, \(\overline{n} \ge 1\).
For microwave frequencies, however, the stimulated emission processes can be significant even at room temperature \(\left( {T = 300\;{\text{K}}} \right)\), as calculated by example 4. This explains why Microwave Amplification by Stimulated Emission of Radiation “MASER” was more early and easily attained than Light Amplification by Stimulated Emission of Radiation “LASER”.
3.11 Laser Gain and Stimulated Emssion Cross Section
Laser rate equation for the upper level \(N_{2}\) can be presented
Atomic energy levels are not infinitely sharp, but have some width associated with them. As a result, the spectrum of transition is not shap lines but have some distribution. By considering laser line shape function \(g\left( \upsilon \right)\) [1,2,3,4,5,6], change in population density by stimulated emission \(N_{21}\) and change in population density by stimulated absorption \(N_{12}\) are defined:
\(N_{21} - N_{12}\) denotes net change in population density: \(N_{21}^{net}\).
where
Since light energy intensity \(I\left( \upsilon \right)\) with unit \(\left[ {\frac{{\text{J}}}{{{\text{m}}^{2} }}} \right]\) equals to the product of photon energy density \(\rho \left( \upsilon \right) {\text{with unit}}\) \(\left[ {\frac{{\text{J}}}{{{\text{m}}^{3} {\text{H}}_{{\text{z}}} }}} \right] = \left[ {\frac{{{\text{J}} \cdot {\text{s}}}}{{{\text{m}}^{3} }}} \right]\) and light velocity within the laser medium \(\frac{c}{n}\) with unit \(\left[ {\frac{{\text{m}}}{{\text{s}}}} \right]\).
Dimensional analysis of (3.50)
Photon energy density \(\rho \left( \upsilon \right)\) in (3.49) can hence be replaced by \(I\left( \upsilon \right) \frac{n}{c}\).
Relation between \(N_{21}^{net}\) and \(I\left( \upsilon \right)\) is found
By adding photon energy to the active volume in Fig. 3.10.
Light intensity increament inside the volume can be calculated:
By considering laser gain definition
By comparing (3.54) and (3.56), we obtain
From Einstein relation in active medium with refractive index n.
We finally obtain the analytical presentation of laser gain \(G\left( \upsilon \right)\)
A more simplified presentation of \(G\left( \upsilon \right)\) is reached by using
One of the most important parameter of laser physics: Stimulated Emission Cross Section \(\sigma \left( \upsilon \right)\user2{ }\) is finally defined as
Sitmulated emission cross-section is purely related to the property of laser active medium, depending only on upper level lifetime \(\uptau\)21, refractive index n, laser wavelength \(\lambda\) and line shape function \(g\left( \upsilon \right)\) of the laser medium. Consequently, laser gain can be more simply defined as the product of the stimulated emission cross section \(\sigma \left( \upsilon \right)\) and the population inversion \(N_{2} - N_{1}\).
3.12 Upper Level Laser Rate Equation
In a four-level laser, a pump excites atoms, molecules, or other atomic systems from the ground state level to an excited state (pump level). A sustained laser emission can be achieved by using atoms that have two relatively stable levels between their ground level and pump level. The atoms first drop to a long-lived metastable state (Upper level \(N_{2}\)) where they can be stimulated to emit excess energy. However, instead of dropping to the ground level, they stop at lower level \(N_{1}\) above the ground level from which they can more easily be excited back up to the higher metastable state, thereby maintaining the population inversion needed for continuous laser operation. By taking into account the contribution of pumping \(W_{p}\) and laser lineshape function \(g\left( \upsilon \right)\), the upper level laser rate equation can be presented: (Details on how to calculate solar pump rate \(W_{p}\) will be explained in Sect. 3.23), (Fig. 3.11).
From Einstein relation
Since
where \(\sigma \left( \upsilon \right) = \frac{{A_{21} \lambda_{0}^{2} }}{{8\pi n^{2} }}g\left( \upsilon \right)\).
We can finally replace \(\rho \left( \upsilon \right) B_{21} g\left( \upsilon \right)\) by \(\sigma \left( \upsilon \right) \frac{I\left( \upsilon \right)}{{h\upsilon }}\) in (3.63).
Finally, we obtain an important laser rate equation involving pump rate \(W_{p}\), stimulated emission cross section \(\sigma \left( \upsilon \right)\), number of photons per unit area per unit time \(\frac{I\left( \upsilon \right)}{{h\upsilon }}\), upper level pupulation \(N_{2}\), lower level population \(N_{1}\) and spontaneous emission constant \(A_{21}\).
3.13 Light Intensity Increment Along Active Medium
At steady state oscillation, the populations is independent of time
Due to the rapid transition from lower level to ground level, zero population \(N_{1} = 0\) for the lower level is assumed.
Consequently
Since
Then
where \(W_{p}\) is the pump rate in unit \(\left[ \frac{1}{\text{s}} \right]\).
Saturation intensity \(I_{S}\) is hence defined
When I = 0, population inversion \(N_{2}\) reaches its maximum value
Therefore, the relation between population inversion in upper level \(N_{2}\) and laser light intensity \(I\) is found (Fig. 3.12).
By laser gain definition
By assuming zero lower level pupulation \(N_{1} = 0\) for (3.73) and using (3.72)
Therefore
Equation (3.76) can be solved numerically.
Simplified solution for (3.76) can be found in two following cases
-
1.
\(I \ll I_{Sat}\) (Weak pumping), \(\frac{I}{{I_{Sat} }}\) is negligible in (3.74)
Therefore (Fig. 3.13)
-
2.
\(I \gg I_{Sat}\) (Very strong pumping), \(\ln \frac{I}{{I_{In} }}\) is negligible in (3.76)
Equation (3.76) can then be simplified to (Fig. 3.14)
3.14 Laser Oscillation Threshold Condition
Laser intensity enhencement \(I^{\prime}\) after one round-trip, starting from I at point A and ending at the same point (Fig. 3.15).
For a laser resonator composed of a HR end mirror with laser wavelength reflectance of R1 (approaching 100%), a PR output mirror with laser wavelength reflectance of R2 (may vary between 40 and 99% for example), an active medium with rod length l and loss Li, laser oscillation threshold condition can be determined by assuming \(I^{\prime } = I\), leading to the following equation
Therefore
Threshold population inversion density can be calculated
It is convenient to introduce some new quantities \(\upgamma\), which can be described as the logarithmic loss per pass, namely.
\(\gamma_{1}\) and \(\upgamma _{2}\) are the logarithmic losses per pass due to the mirror transmission and \(\upgamma _{i}\) is the logarithmic internal loss per pass. \(T_{1}\) and \(T_{2}\) are laser wavelength reflectivities of the HR end mirror and the PR output mirror, respectively. The logarithmic loss notation proves to be the most convenient way of representing laser losses, given the exponential character of the laser gain. Threshold population inversion density \(N_{2} - N_{1}\) can hence be presented.
Example 5
Calulation of threshold population inversion density \(N_{2} - N_{1}\) for a laser resonator with a \(l = 5\;{\text{cm}}\) length Nd:YAG rod with \(\sigma = 3 \times 10^{ - 19}\; {\text{cm}}^{2}\) stimulated emission cross section and \(\alpha = 0.003\;{\text{cm}}^{ - 1}\) absorption and scattering loss coefficient.
By using laser resoant cavity parameters indicated in Fig. 3.16
Threshold population inversion density \(N_{2} - N_{1}\) for the Nd:YAG medium can be calculated by (3.89)
3.15 Laser Rate Equation Involving Resonant Cavity
As shown in Fig. 3.17, by photon absorption, atoms are excited to upper laser level at a pump rate \(W_{p}\) per second per unit volume, the rate equations for a four-level material can be used [10]
where \(W_{p}\) is the pump rate, N is the population inversion density, Nt is the total number density of the active atoms in the laser rod (for 1.0 at.% \(Nd^{3 + } YAG\) medium, \(N_{t} = 1.38 \times 10^{20}\; {\text{cm}}^{ - 3}\)), c is the velocity of light in vacuum, \(\sigma\) is the stimulated emission cross section, \(\tau\)e is the effective lifetime of the upper laser level, and \(\rho\) is the photon density in the laser cavity. \(L^{\prime }\) is the effective cavity length and is given as
where \(L_{C} {\text{ is }}\) the length between the two cavity mirrors, \(n\) is the refractive index of the laser host material, and l is the length of the laser material.
For a laser resonator with an active medium, \(\gamma\) represents the logarithmic loss by the scattering and absorption of the laser light in the laser material and by the transmission of the two laser cavity mirrors, \(\gamma\) is thus given as
where \(\alpha\) is the scattering and absorption losses per unit length, \(R_{1}\) is the reflectance of the full mirror, and \(R_{2}\) is the reflectance of the output coupler mirror.
The first term on the right-hand side of (3.91) represents the rate of photon density increase in the laser cavity by stimulated emission and the second term represents the photon loss rate due to the scattering and to the transmittance of the cavity mirrors. The photon loss rate coefficient can hence be written as
3.16 Calculation of Photon Density Within a Laser Resonant Cavity
The population inversion in the laser cavity while the laser is in CW oscillation can be calculated from the photon rate Eq. (3.90) by applying the time invariant condition of the population density: \(\frac{dN}{{dt}} = 0\)
Also, by applying the time invariant condition of the photon density \(\frac{ d\rho }{{dt}} = 0\) to (3.91) at the threshold
where threshold inversion population \(N_{c }\) is proportional to the single-trip cavity loss \(\gamma\) and inversely proportional to the product of the stimulated emission cross-section \(\sigma\) and the rod length \(l\).
Since the population inversion density \(N\) is clamped at the threshold inversion density \(N_{c}\) [1]
The photon density \(\uprho\) within the laser cavity is finally obtained.
3.17 Solar Concentration Ratio
The ratio between the concentrated flux on the receiver and the ambient flux from the sun is called the optical concentration ratio. Geometric concentration ratio \(C\) is defined as the area of solar collector Sa divided by the surface area of the receiver Sr. The laser rod surface can be considered as a receiver.
where \(S_{a}\) is primary solar collector area, \(\pi\)Dl is the laser rod side surface area exposed to concentrated solar pump rays.
3.18 Transfer Efficiency
Transfer Efficiency \(\user2{ \eta }_{{\varvec{T}}}\) can be defined as the ratio between the solar power incident on laser active medium and the incoming solar power reaching the primary solar collector [11].
where
- \(\eta_{tg}\):
-
is a geometrical transfer factor from the solar collector to the surface of the laser medium and is usually independent of wavelength.
- \(\eta_{tl} \left( \lambda \right)\):
-
takes into account the reflection and transmission losses of primary, secondary solar concentrators and laser pump cavity.
The absorption by cooling liquid, the reflection and scattering losses at the laser medium and flow tube should be considered.
The integral in (3.102) is taken over the wavelength range between \(\lambda_{1}\) and \(\lambda_{2 }\), which are useful for pumping the upper laser level. As an example, solar spectral irradiance I(λ) and complex absorption spectra α(λ) of 1.0 at. % Nd:YAG medium are presented by orange and blue lines, respectively in Fig. 3.18. The integral in (3.102) is taken over the wavelength range from \(\lambda_{1} = 530\;{\text{nm}}\) to \(\lambda_{2 }\) = 880 nm for pumping the upper laser level.
3.19 Absorption Efficiency
Absorption Efficiency \(\user2{ \eta }_{{\varvec{A}}}\) describes conversion of incident solar power incident on the surface of the active medium to the total absorbed pump power by the same medium.
Absorption efficiency \(\eta_{A}\) can be defined as [11]
where:
- \(P_{a}\):
-
is the total absorbed solar power by the active medium.
- \(P_{e\lambda }\):
-
is the power per unit wavelength incident on the medium.
For solar-pumped solid-state lasers, absorption efficiency calculations require the absorption spectra of the laser material and the solar emission spectra, as shown in Fig. 3.18, where pump source is characterized by solar spectral distribution \(I\left( \lambda \right)\), and the laser material is characterized by absorption coefficients \(\alpha \left( \lambda \right)\).
In addition, the angular distribution of the concentrated solar light on the laser material, as well as the geometry of the laser material and its refractive index also need to be known.
For solid-state lasers, the pump source is characterized by a relative spectral distribution I(λ), and the laser material is characterized by an absorption coefficient \(\alpha \left( \lambda \right)\), as shown in Fig. 3.18.
The pump photons have a distribution of incident angles F(θ, φ), and travel a path length L(θ, φ) in the laser material which depends on the incident angles θ and φ.
Given this, the absorption efficiency can be found [12]
where
Integration is over all incident angles allowed by the angular distribution \(F\left( {\theta ,\phi } \right)\).
Integration over wavelength is all wavelengths emitted by the pump source.
L is defined as the effective absorption length of pump light within the laser rod.
\(\alpha \left( \lambda \right)\) is the absorption coefficient of the laser medium.
\(\lambda_{L}\) is the laser wavelength.
1/λL is used to normalize so the efficiency is dimensionless.
Integration may vary between \(\lambda_{1} = 0.3\;\upmu {\text{m}}\) to \(\lambda_{2}\) = 2.4 μm for solar-pumped lasers.
However, when an active medium has a limited absorption bandwidth, integration over wavelength may vary only from \(\lambda_{1} = 0.5\;\upmu {\text{m}}\) to \(\lambda_{2} = 0.88\;\upmu {\text{m}}\), as for the case of solar pumping of Nd:YAG material, as indicated in Fig. 3.18.
3.20 Deviation Angle and Effective Absorption Length
Numerically, the non-sequential method of Zemax® program can be used for calculating the above mentioned transfer efficiency \(\eta_{T}\) by (3.102) and absorption efficiency \(\eta_{a}\) by (3.103).
As shown in Fig. 3.19, a detector rectangle can be placed beneath the laser rod surface in Zemax® program. The deviation angles of \(\alpha\) and \(\beta\) in transversal and longitudinal directions, respectively, can be detected by using the irradiance (angle space) function of the detector rectangle in Zemax® program [13].
Once \(\alpha\) and \(\beta\) are found, the most important parameter in Fig. 3.19, defined as the deviation angle of the solar pump ray within the laser rod, \(\beta^{\prime }\) can be calculated
Effective absorption length \(L\) of the solar pump ray can be finally calculated
As compared to the complicated analytical modeling by (3.102) and (3.104), transfer efficiency \(\eta_{T}\) and absorption efficiency \(\eta_{a}\) can be more accurately and easily calculated by Zemax® software.
By assuming an infinite absorption coefficient \(\alpha \left( \lambda \right) = \infty\) for a laser medium, all the incident rays are considered absorbed by the laser rod surface.
A rectangular volume detector can be used to calculate the total solar pump power incident on the surface of the laser rod, as shown in Fig. 3.20. Consequently, transfer efficiency can hence be calculated by (3.107).
where
- \(P_{{Rod}\; {surface}}\):
-
denotes the solar pump power incident on the surface of the laser rod, as indicated by Fig. 3.20.
- \(P_{{Primar}\; {collector}}\):
-
denotes the total incoming solar power reaching the primary solar collector.
3.21 Upper State Efficiency
Upper State Efficiency \(\user2{ \eta }_{{\varvec{U}}} \left( {\varvec{\lambda}} \right)\) is defined as the product of two contributing factors
-
1.
Quantum efficiency \(\eta_{Q} \left( \lambda \right)\).
-
2.
Quantum defect efficiency \(\eta_{s} \left( \lambda \right)\), also referred as Stokes factor.
$$\eta_{U} \left( \lambda \right) = \frac{{P_{U} }}{{P_{A} }} = \eta_{Q} \left( \lambda \right)\,\eta_{S} \left( \lambda \right)$$(3.108)
Quantum Efficiency \({\varvec{\eta}}_{{\varvec{Q}}} \left( {\varvec{\lambda}} \right)\) can be defined as the ratio of the number of atoms raised to the upper laser level to the number of absorbed pump photons [11]. It relates the probability of an absorbed photon producing an atom in the upper laser level. We can thus write:
where \(N_{2}\) denotes upper level population, \(P_{a}\) denotes the absorbed solar pump power.
Photons absorbed in a pump manifold may bypass the upper laser manifold by radiative decay to a manifold that is lower. In all probability, the decay from the pump to the upper laser manifold occurs by non-radiative transitions. If the upper laser manifold is directly below the pump manifold, the quantum efficiency is approximately [12].
where \(\tau_{NR}\) and \(\tau_{RAD}\) are the pump manifold non-radiative and radiative lifetimes, respectively.
Quantum Defect Efficiency \({\varvec{\eta}}_{{\varvec{S}}} \left( {\varvec{\lambda}} \right)\), also called Stokes factor, is the ratio of the photon energy emitted at the laser transition, to the energy of a pump photon [11].
where: \(\lambda_{p}\) and \(\lambda_{L}\) are the pump transition and laser wavelengths, respectively.
In solar-pumped solid-sate lasers, the pump wavelength is defined as the mean absorbed and intensity-weighted solar radiation wavelength [15]
where the integration is performed over the laser absorption bands between \(\lambda_{1}\) and \(\lambda_{2}\) and \(I\left( \lambda \right)\) is the standard solar spectral irradiance, as shown in Fig. 3.18.
Since the laser wavelength of Nd:YAG laser material is \(\lambda_{L}\) = 1064 nm for solar-pumped Nd:YAG laser, λP = 660 nm was calculated by (3.112), ηS = 0.62 quantum defect efficiency is calculated for the Nd:YAG emission wavelength of λL = 1064 nm by (3.111).
Typically, upper state efficiencies of a Nd:YAG medium show a variation of \(\eta_{U} \left( \lambda \right)\) from 0.58 to 0.60 [11], revealing its slight dependence on laser rod diameter. Consequently, upper state efficiency of \({\varvec{\eta}}_{{\varvec{U}}} \left( {\varvec{\lambda}} \right) = \mathbf{0.59}\) is adopted in the following sections.
3.22 Beam Overlap Efficiency
Beam Overlap Efficiency \({\varvec{\eta}}_{{\user2{B }}} \user2{ }\) expresses the spatial overlap between the laser resonator modes and the pumped region of the laser medium, which can be given by an overlap integral [11].
where
\(\rho \left( {x, y, z} \right)\) is cavity mode energy density and \(\rho_{0}\) is the total value of the energy density.
\(W_{p} \left( {x, y, z} \right)\) denotes the pump rate per unit volume, \(W_{p0}\) is the total number of absorbed photons.
The relation between pump rate and absorbed power is given by
Choice of laser geometry can have a profound effect on overlap efficiency and average power capability. Historically, laser geometries were often in the form of cylinders. They can also be useful for end pumping of laser materials with low absorption coefficients. Laser rods pose a hard aperture making extraction of the population inversion near the periphery of the laser rod more difficult. If laser operation is restricted to TEM00 modes, the beam radius is often set at about 0.6 of the laser rod radius. This restricts the overlap efficiency to roughly 0.36 [12].
In addition, cooling was usually achieved by flowing coolant over the lateral surface of the laser rod. This leads to radial thermal gradients and thermal lensing that degrades beam quality and limits average power.
Consequently, analytical calculation of the beam overlap efficiency of a solid-state laser by (3.113) is rather complex, since it is strongly dependent on the resonator parameters such as radius of curvature of cavity mirrors, cavity length, rod diameter and, more importantly, also on solar pumping conditions such as tracking errors of either a heliostat or a solar tracker in the case of solar-pumped lasers.
Therefore, it is very important to note that laser output power from a resonant cavity with a certain length L presents usually a considerably reduced laser output power level due to the influence of the beam overlap efficiency of less than unity (\(\eta_{B} < 1\)), as compared to that of a closely coupled laser resonant cavity with \(\eta_{B} = 1\). Zemax® and LASCAD™ analyses of laser output power from a laser cavity with a certain length L was presented in Sect. 2.3 of Chap. 2. Detailed examples will also be provided in Sect. 6.2 of Chap. 6.
Finally, it is important to note that in the pump rate and the solar laser output power analysis in the following sections, \(\eta_{B} = 1\) is usually assumed, corresponding to a laser cavity with HR and PR mirrors closely positioned near the laser rod, allowing the maximum extraction of laser power from that rod.
3.23 Atom Number Density and Solar Pump Rate Calculations
By considering a solar laser collection and concentration system with concentration factor \(C\), the concentrated solar spectral irradiance \(I^{\prime } \left(\uplambda \right)\) incident on the laser rod surface can be calculated
where \(I\left( {\uplambda } \right)\) is the one-Sun solar spectral irradiance, as indicated by Fig. 3.18. \({ } \eta_{T} \left( \lambda \right)\) is the solar power transfer efficiency from the primary solar collector to the surface of the laser medium.
The absorbed photon number by the laser rod with diameter \(D\) and effective absorption length \(L\) can hence be calculated
Atom number density \(N_{U}\) (\({\text{unit}} \frac{1}{{{\text{cm}}^{3} }}\)) in the upper laser level can be calculated by considering upper state efficiency \(\eta_{U} \left( \lambda \right)\) and laser rod volume
Since \(\eta_{T} \left( \lambda \right)\) varies only slightly with wavelength \(\lambda\) within each simplified absorption band in Fig. 3.21 in Sect. 3.2, atom number density \(N_{U}\) in upper laser level can be finally obtained
In the calculation of the output power, one of the most important parameters is the pump rate \(W_{p}\). By dividing the atom number density \(N_{U}\) in the upper level by the total number density of the active ions in the laser rod \(N_{t}\) (for 1.0 at.% \(Nd^{3 + } YAG\) medium, \(N_{t} = 1.38 \times 10^{20}\; {\text{cm}}^{ - 3}\)), the pump rate Wp can then be calculated
3.24 Solar Laser Output Power Calculation
The laser output power \({P}_{out}\) of a continuous-wave laser is calculated from the following relation
and
where V is defined as lasing volume in the cavity, where A is the laser beam cross section, and \(L^{\prime }\) is the effective cavity length
Since photon loss rate through output mirror is presented by the third term on the right-hand side of (3.94)
Photon loss rate through output mirror is also defined as laser power extraction efficiency.
Extraction Efficiency \({{\varvec{\eta}}}_{{\varvec{E}}}\)
Laser extraction efficiency is determined by (3.127)
By applying photon density \(\rho\) of (3.100)
Since normally, \(\frac{{N_{t} \sigma l}}{\gamma } \gg 1\), we can reach a simplified equation for \(P_{out}\)
We then reach a simplified presentation for laser output power
where: \(\eta_{s}^{\prime }\) is defined as laser slope efficiency
\(W_{pth}\) is defined as threshold pump rate.
From (3.133), it is important to note that \(W_{pth}\) is directly proportional to resonant cavity loss \(\gamma\), and inversely proportional to the product of four important laser gain parameters, e.g. stimulated emission cross section \(\sigma\), upper level lifetime \(\tau_{e }\), active ion number \(N_{t}\) and laser rod length \(l\). Consequently, threshold pump rate can be either reduced by diminishing \(\gamma\) or by increasing \(\sigma , \tau_{e } ,N_{t} ,l\) values.
By considering solar concentration ratio definition.
Incoming solar laser can be calculated by (3.134)
where \(I_{0}\) is the one-sun solar insolation in unit of power per unit area (Standard one-Sun irradiance value: \(I_{0} = 1000 \frac{{\text{W}}}{{{\text{m}}^{2} }}\)).
Solar power to laser power conversion efficiency can then be calculated
Maximum pump power to threshold pump power ratio is defined
Solar laser slope efficiency can also be calculated
3.25 Solar Spectral Irradiance and Simplified Model for Nd:YAG Absorption Spectrum
As shown in Fig. 3.21, the absorption spectra of Nd:YAG laser materials are rather complex. The absorption curve is composed of a couple of bands. Moreover, each band has a complex structure. Consequently, the analytical estimation of the pump rate by unit solar constant is rather difficult.
We therefore modeled the adsorption curves of the Nd:YAG laser material for the convenience of calculation. Five simplified absorption bands centered at 530 nm, 580 nm, 750 nm, 810 nm and 860 nm along with their respective absorption bandwidths of 28 nm, 28 nm, 31 nm, 33 nm, and 22 nm respectively (green color numbers in Fig. 3.21) are considered.
A simplified absorption coefficient value \(\sigma_{a } \left( {\frac{{\lambda_{a} + \lambda_{b} }}{2}} \right)\) for each band is assumed, corresponding to 40% of the peak absorption coefficient of that band, so that the area under the modelled absorption curve (black color) could be equal to that under the real absorption curve (blue color) in each band, as shown in Fig. 3.22.
Consequently, simplified absorption coefficients 1.39 cm−1, 2.87 cm−1, 3.11 cm−1, 3.64 cm−1 and 1.23 cm−1 are determined for 530 nm, 580 nm, 750 nm, 810 nm and 860 nm bands, respectively, as indicated by Fig. 3.21. Correspondingly, 1.35 W/m2/nm, 1.31 W/m2/nm, 1.12 W/m2/nm, 1.00 W/m2/nm, 0.87 W/m2/nm solar irradiance values are found to match the five simplified absorption bands centered at 530 nm, 580 nm, 750 nm, 810 nm and 860 nm, respectively.
Other absorption band of the Nd:YAG medium at UV wavelength in Fig. 3.21 is not considered since it does not contribute to 1064 nm laser emission process.
3.26 Absorbed Solar Power Density and Absorbed Pump Photon Number Density Calculations
To calculate absorbed solar power density and photon number density in each of the five simplified absorption band, as shown in Fig. 3.21, the following parameters are assumed constant within each of the simplified absorption band.
Consequently, the absorption integral \(\int {I(\lambda )} \eta_{U} \left( \lambda \right)\left\{ {1 - exp\left[ { - \sigma_{a} \left( \lambda \right)L } \right]} \right\} d\lambda\) for each of the five absorption band can be simplified as
We then reach a simplified equation for calculating the absorbed solar power density within each band with \({\Delta }\lambda = \lambda_{b} - \lambda_{a}\) bandwidth.
Absorbed solar power density in each band
Absorbed photon number density in each band may also be simplified according the constant parameter conditions of (3.138), (3.139) and (3.140).
Simplification of integral \(\int {\frac{{I\left(\uplambda \right)}}{{h \nu_{p} \left( \lambda \right)}}} \eta_{U} \left( \lambda \right)\left\{ {1 - exp\left[ { - {\upalpha }\left( \lambda \right)L} \right]} \right\} d\lambda\) for each band
Absorbed photon number density in each absorption band is finally calculated
3.27 Output Power Analysis of a Side-Pumped Nd:YAG Solar Laser
3.27.1 Modified Analytical Method for the Side-Pumped Nd:YAG Solar Laser
An astigmatic corrected target aligned (ACTA) primary parabolic mirror with \(S_{a}\) = 6.85 m2 collection area was used to both collect and concentrate incoming solar power to a single-stage 2-dimensional compound parabolic concentrator (2D-CPC) with 8.9 cm × 9.8 cm rectangular input face. A D = 10 mm diameter and l = 130 mm length 1.1% Nd:YAG laser rod was mounted inside a quartz flow tube, which was located along the 2D-CPC axis, as depicted in Fig. 3.23 [16].
Solar concentration ratio C
Absorbed pump power distribution of the Nd:YAG laser rod is presented by Fig. 3.24.
Since only 10 cm length of the laser rod is exposed to concentrated solar radiation within the 2D CPC pump cavity, the surface area of this exposed section of the rod is considered as a receiver, consequently.
By considering \(S_{a} = 6.75\;{\text{m}}^{2}\) ACTA primary solar collector area, the solar concentration ratio can be calculated
Effective absorption length L
To calculate the absorption path length L of solar pump light within the 10 mm diameter, 130 mm length Nd:YAG rod in Figs. 3.23 and 3.24, eight rectangular detectors are equally spaced around the internal surface of the rod, as indicated by Fig. 3.25. As shown in Fig. 3.19, the deviation angles of \(\alpha\) and \(\beta\) of the solar ray in each detector position can be detected, so that deviation angle \(\upbeta ^{\prime }\) and, consequently, effective pump absorption path L at each of the eight detector positions can be calculated by (3.105), (3.106), respectively.
Figures 3.26, 3.27, 3.28, 3.29 and 3.30 below show the Zemax® non-sequential ray tracing results of angle space distribution obtained from each detector rectangle. Deviation angles \(\alpha\) and \(\beta\) are determined by cross section row FWHM X-coordinate value and cross section column FWHM Y-coordinate value of detectors 1–5, respectively.
Since the 2D-CPC secondary concentrator ensures a symmetric pump profile for the rod, Detector 2′, Detector 3′ and Detector 4′ in Fig. 3.25 present the same amount of detected power, the same deviation angles of \(\alpha\) and \(\beta\), and consequently, the same absorption lengths as that of Detector 2, Detector 3 and Detector 4, respectively.
Table 3.1 summarize the detected pump power for each detector. Relative weight for each detector can also be calculated. Effective absorption length in different detector positions, ranging from L1 to L5, are finally listed.
Finally, weighted effective absorption length L can be finally calculated
Calculation of absorbed solar power and absorbed photon number density in the five bands
Once the weighted effective absorption length is calculated \((L = 1.27\,{\text{cm}})\), the amounts of absorbed pump power density and absorbed photon density within each of the five simplified absorption band in Fig. 3.21 can be finally calculated by using (3.143) and (3.145).
It is also important to note that simplified absorption coefficient of each band corresponds to 40% of the peak absorption coefficient value of that band \(\sigma_{a} \left( {\frac{{\lambda_{a} + \lambda_{b} }}{2}} \right)\) = 40% \(\sigma_{a-peak}\), as indicated in Fig. 3.21 by blue color text.
By adopting Eq. (3.143):
Absorbed solar pump power density in 530 nm band can be calculated
By adopting Eq. (3.145):
Absorbed solar photon number density in 530 nm band can also be calculated
In the same way, absorbed solar pump power density in 580 nm band
Absorbed solar photon number density in 580 nm band
Absorbed solar pump power density in 750 nm band
Absorbed solar photon number density in 750 nm band
Absorbed solar pump power density in 810 nm band
Absorbed solar photon number density in 810 nm band
Absorbed solar pump power density in 860 nm band
Absorbed solar photon number density in 860 nm band
Finally, we obtain the total absorbed solar power density of the five absorption bands
And the total absorbed photon number density from the five bands:
Calculation of one sun pump rate \({\varvec{W}}_{{\varvec{p}}}^{\prime }\)
The astigmatic corrected target aligned (ACTA) parabolic mirror with 6.75 m2 collection area was used to both collect and concentrate incoming solar power. For \(950\frac{{\text{W}}}{{{\text{m}}^{2} }}\,{\text{solar}}\,{\text{irradiance}}\), 6412.5 W incoming solar power was calculated. By assuming infinite absorption coefficient \(\upalpha _{{\text{a}}} \left(\uplambda \right) = \infty\), 4225.8 W absorbed power at rod surface was detected by Zemax® software.
Consequently, \({\varvec{\eta}}_{{\varvec{T}}} \ = \user2{ }\frac{{4225.8{\varvec{W}}}}{{6412.5{\varvec{W}}}} = 0.659\) transfer efficiency was calculated.
As discussed in Sect. 3.20, \({\varvec{\eta}}_{{\varvec{U}}} \left( {\varvec{\lambda}} \right) = 0.59\) upper state efficiency was assumed in our analysis [11].
Since both which \(\eta_{T} \left( \lambda \right)\,{\text{and}}\,\eta_{U} \left( \lambda \right)\) remain nearly constant within each of the five absorption bands, we then reach simplified equation for one sun pump rate
Calculation of threshold pump rate \({\varvec{W}}_{{{\varvec{pth}}}}\)
For 1.1 at.% Nd:YAG rod, \(\sigma = 6.5 \times 10^{ - 19}\; {\text{cm}}^{2}\), \(l = 13\;{\text{cm}}\), D = 1 cm, A = \(0.785\;{\text{cm}}^{2}\) \(R_{1} = 0.998,\) \(R_{2} = 0.95,\) \(N_{t} = 1.518 \times 10^{20}\; {\text{cm}}^{ - 3}\).
The single-trip loss of the laser resonant cavity is firstly calculated
Then we can calculate the threshold solar pump rate
Calculation of solar laser output power
Calculation of \(\frac{{{\varvec{P}}_{{{\varvec{in}}}} }}{{{\varvec{P}}_{{{\varvec{pth}}}} }}\) ratio
Calculation of threshold pump power \({\user2{P}}_{{{\mathbf{pth}}}}\)
Calculation of solar to laser power conversion efficiency \({\varvec{\eta}}\)
With 6.75 m2 collection area, at 950 W/m2 solar irradiance, 6412.5 W incoming solar power is calculated.
Calculation of solar laser slope efficiency \({\varvec{\eta}}_{{\mathbf{slope}}}\)
3.27.2 Classical Analytical Method of Side-Pumped Solar Laser
The following equations are commonly used classical analytical method for calculating laser output power \(P_{out }\), slope efficiency \(\eta_{{\text{s}}}\) and threshold pump power \(P_{th }\) of solid-state lasers [2].
where:
For the side-pumped solar laser in Fig. 3.23, all other important parameters and laser output power are calculated by (3.158), (3.159) and (3.160) and listed by Table 3.2.
3.27.3 LASCAD™ Analysis of the Side-Pumped Solar Laser
Similar to the Zemax® and LASCAD™ solar laser analysis examples in Chap. 2, the absorbed pump flux data from the Zemax® analysis of the side-pumped solar laser in Figs. 3.23 and 3.24 can be processed by LASCAD™ software to evaluate laser output performances.
The stimulated emission cross-section of 6.5 × 10–19 cm2, the fluorescence life time of 230 μs and an absorption and scattering loss of 0.003 cm−1 for the 1.1 at.% Nd:YAG medium were adopted in LASCAD™ analysis. The mean absorbed and intensity-weighted solar pump wavelength of 660 nm [14] was also used in the analysis. For the 10.0 mm diameter, 1.1 at.% Nd:YAG rod with length LR = 130 mm, the amount of absorption and scattering losses was 2 α LR = 5.2%. Assuming 0.4% of imperfect HR and AR coating losses, the round-trip loss was increased to 5.6%. The diffraction losses depend heavily on rod diameter, resonator length and RoC of the resonator mirrors. LASCAD™ beam propagation method (BPM) resulted in a negligible diffraction loss when HR1064 nm end mirror and PR1064 nm output mirror, all with RoC = ∞, were placed very close to the laser rod. Final round-trip loss of 5.6% was calculated. Consequently, 72.5 W multimode solar laser power was numerically calculated.
By considering the incoming solar power of 6412.5 W and for the maximum solar laser output power of 72.5 W, solar-to-laser conversion efficiency of 1.13% is calculated. Effective threshold solar pump power and maximum effective solar power of 104.4 W, 417.0 W was indicated in Fig. 3.31, respectively, corresponding to 1587.3 W threshold solar power and the maximum incoming solar power of 6412.5 W, respectively. Solar laser slope efficiency of 1.5% was hence be calculated. Maximum pump power/threshold pump power ratio of 4.04 was calculated. All the above mentioned parameters are indicated in Table 3.3.
Under the same pumping conditions for the laser resonator with L = 430 mm length, 45.9 W laser output power, 1687.5 W threshold pump power, 0.716% solar-to-laser conversion efficiency, 0.97% laser slope efficiency and 3.8 maximum pump power/threshold pump power ratio were calculated by LASCAD™ software, as shown in Fig. 3.32.
3.27.4 Comparison of Different Analysis Methods of the Side-Pumped Solar Laser
Discussions
As shown by Table 3.3, both the modified and the LASCAD™ analyses predicted nearly the same maximum extractable multimode laser power and solar-to-laser conversion efficiency when the HR1064 nm end mirror and PR1064 nm output mirrors were closely placed near the Nd:YAG laser rod. This happened when unity overlap efficiency \(({\eta }_{B}=1)\) was assumed in the modified method. Classical analytical method offered a considerably reduced prediction accuracy for laser power and efficiency, as indicated by Table 3.3.
However, it is important to note that both the modified and the classical analyses were not effective in predicting the output power from a laser resonant cavity with a certain cavity length L (\({\eta }_{B}<1\)), since it was very difficult to calculate analytically the beam overlap efficiency of solar-pumped lasers, as mentioned in Sect. 3.22.
Zemax® and LASCAD™ analyses were effective in the laser output power prediction of a solar laser with certain cavity length, as explained in Sect. 2.26 of Chap. 2. Detailed analysis method will be provided in Sect. 6.2.1 of Chap. 6.
When the HR1064 nm end mirror and the PR1064 nm output mirror were positioned 430 mm away from each other, there was a noticeable reduction in beam overlap efficiency (\({\eta }_{B}<1\)), consequently, 45.9 W solar laser output power was calculated by Zemax® and LASCADL430mm analyses, as shown by Fig. 3.32 and confirmed by experimental result [16].
As for the prediction of threshold solar pump power, all the analyses including LASCAD™ failed to a considerable extent, leading normally to a much smaller threshold power prediction accuracy, as compared to the experimental result in Table 3.3.
3.28 Output Power Analysis of an End-Side-Pumped Nd:YAG Solar Laser
3.28.1 Modified Analytical Method for the End-Side-Pumped Nd:YAG Solar Laser
Solar concentration factor C
The Fresnel lens collector has the collection area of \(S_{A} = \pi R^{2} = 6358.5\;{\text{cm}}^{2}\) (Fig. 3.33).
The \(D = 0.4\;{\text{cm}},\,l = 2.1\;{\text{cm}}\) rod has an exposed surface area of \(S_{R} = \frac{{\pi \,D^{2} }}{4} + \pi \,D\,l = 2.763\,{\text{cm}}^{2}\).
The solar concentration ratio C is hence calculated:
Effective absorption length L
By Zemax® analysis, 24.8% of all the solar pump ray were found to enter the D = 4 mm diameter and l = 25 mm length Nd:YAG rod through its HR1064 nm end face, ensuring the most efficient pump light absorption through end-pumping configuration. Similar to the divergence angle analysis of the solar pump rays within a laser rod in in Sect. 3.27, a square detector (Detector 1) was placed beneath the HR1064 nm end face of the D = 4 mm diameter and l = 25 mm length Nd:YAG rod, as indicated by Figs. 3.34 and 3.35. \(\gamma_{x}\) = \(\gamma_{y}\) = 20̊ divergence angles were detected. Effective absorption length \(L_{\text{End-pumping}} = 2.81\,{\text{cm}}\) was consequently calculated.
By Zemax® analysis, 69.6% of all the solar pump ray were found to enter the D = 4 mm diameter and l = 25 mm length Nd:YAG rod through its side barrel face, ensuring also an efficient pump light absorption through three-pass side-pumping configuration, a detector rectangle (Detector 2) was placed beneath the side face of the D = 4 mm = 0.4 cm diameter and l = 25 mm length Nd:YAG rod, as indicated by Fig. 3.36. α=32∘, β=21∘ divergence angles were detected. Effective absorption length LThree-pass=1.39 cm was calculated. End-pumping solar pump rays in Fig. 3.35 were also detected by Detector 2.
By Zemax® analysis, only 5.6% of all the solar pump ray were found to enter the D = 4 mm diameter and l = 25 mm length rod through its side face in one-pass pumping approach, leading to an inefficient pump light absorption. A short detector rectangle (Detector 3) was placed beneath the side face of the Nd:YAG rod, as indicated by Fig. 3.37. α = 25∘, β = 28∘ divergence angles were detected. Effective absorption length LOne-pass = 0.49 cm was calculated. To detect the one-pass rays more effectively, Detector 3 was positioned near the output end of the rod. Besides, since Detector 3 also had a much shorter length than that of Detector 2, contribution of the solar rays through the HR 1064 nm end face was much less pronounced in Fig. 3.37, as compared to that in Fig. 3.36.
Zemax® analysis of different effective absorption lengths and their relative weights for different passes (Table 3.4)
Calculation of absorbed solar power and absorbed photon number density in the five bands
Once the weighted effective absorption length \(\left( {L = 1.69\,{\text{cm}}} \right)\) is found, the amounts of absorbed pump power density and absorbed photon density within each of the five simplified absorption band in Fig. 3.21 can be finally calculated by using (3.143) and (3.145).
By adopting Eq. (3.143): \(I\left( {\frac{{\lambda_{a} + \lambda_{b} }}{2}} \right)\left\{ {1 - \text{exp}\left[ { - \sigma_{a} \left( {\frac{{\lambda_{a} + \lambda_{b} }}{2}} \right)L} \right]} \right\}{\Delta }\lambda\).
Absorbed solar pump power density in 530 nm band
By adopting Eq. (3.145): \(\frac{1}{{h \upsilon \left( {\frac{{\lambda_{a} + \lambda_{b} }}{2}} \right)}}I\left( {\frac{{\lambda_{a} + \lambda_{b} }}{2}} \right)\left\{ {1 - \text{exp}\left[ { - \sigma_{a} \left( {\frac{{\lambda_{a} + \lambda_{b} }}{2}} \right)L} \right]} \right\}{\Delta }\lambda\)
Absorbed solar photon density in 530 nm band
Similarly, absorbed solar pump power density in 580 nm band
Absorbed solar photon number density in 580 nm band
Absorbed solar pump power density in 750 nm band
Absorbed solar photon number density in 750 nm band
Absorbed solar pump power density in 810 nm band
Absorbed solar photon number density in 810 nm band
Absorbed solar pump power density in 860 nm band
Absorbed solar photon number density in 860 nm band
Finally, total absorbed solar power density from the five bands
Total absorbed photon number density from the five bands
Calculation of one Sun pump rate \({\varvec{W}}_{p}^{\prime }\)
For the Fresnel lens with 0.63585 m2 collection area and \(890\frac{{\text{W}}}{{{\text{m}}^{2} }}\,{\text{solar}}\,{\text{irradiance}}\), 565.9 W incoming solar power was calculated. By assuming infinite absorption coefficient \({\varvec{\alpha}}_{{\varvec{a}}} \left( {\varvec{\lambda}} \right) = \infty\), 372.9 W absorbed solar power at rod surface was detected by Zemax® software.
Consequently, \({\varvec{\eta}}_{{\varvec{T}}} = \frac{372.9W}{{565.9W}} = 0.659\) transfer efficiency was calculated.
As mentioned in Sect. 3.20, \({\varvec{\eta}}_{{\varvec{U}}} \left( {\varvec{\lambda}} \right) = 0.59\) upper state efficiency was also assumed [11].
Since both which \(\eta_{T} \left( \lambda \right){\text{ and }}\eta_{U} \left( \lambda \right)\) remain nearly constant within each of the five absorption bands, we then reach simplified equation for one Sun pump rate.
Calculation of threshold pump rate \({\varvec{W}}_{{{\varvec{pth}}}}\)
For the 2.5 cm length Nd:YAG laser rod
Calculation of solar laser output power
Calculation of \(\frac{{{\varvec{P}}_{{{\varvec{in}}}} }}{{{\varvec{P}}_{{{\varvec{pth}}}} }}\) ratio
Calculation of threshold pump power \({\varvec{P}}_{{{\varvec{pth}}}}\)
Calculation of solar to laser power conversion efficiency \({\varvec{\eta}}\)
With 0.636 m2 collection area, at 890 W/m2 solar irradiance, 565.9 W incoming solar power was calculated.
Calculation of solar laser slope efficiency \({\varvec{\eta}}_{{{\varvec{slope}}}}\)
3.28.2 Classical Analytical Method of the End-Side-Pumped Laser
The following equations are commonly used classical analytical method for calculating laser output power \(P_{out }\), slope efficiency \(\eta_{s }\) and threshold pump power \(P_{th }\) of solid-state lasers [2].
where \(I_{s} = \frac{h\upsilon }{{\tau \sigma }} = \frac{{6.63 \times 10^{ - 34}\; {\text{JS}} \times 2.82 \times 10^{14} \;{\text{s}}^{ - 1} }}{{230 \times 10^{ - 6}\; {\text{S}} \times 2.8 \times 10^{ - 19}\; {\text{cm}}^{2} }} = 2.90\,\frac{{{\text{kW}}}}{{{\text{m}}^{2} }}\).
For the side-pumped solar laser in Fig. 3.23, all other important parameters and laser output power are calculated by (3.158), (3.159) and (3.160) and listed by Table 3.5.
3.28.3 LASCAD™ Numerical Analysis of the End-Side-Pumped Solar Laser
The absorbed pump flux data from the Zemax® analysis of the end-side-pumped solar laser in Fig. 3.34 was processed by LASCAD™ software to evaluate its solar laser output performances. The stimulated emission cross-section of 2.8 × 10–19 cm2, the fluorescence life time of 230 μs and an absorption and scattering loss of 0.002 cm−1 for the Nd:YAG medium were adopted in LASCAD™ analysis. The mean absorbed and intensity-weighted solar pump wavelength of 660 nm [14] was also used in the analysis. For the 25 mm diameter, 1.0 at.% Nd:YAG rod with length LR = 25 mm, the amount of absorption and scattering losses was 2 α LR = 1.0%. Assuming 0.4% of imperfect HR and AR coating losses, the round-trip loss was increased to 1.4%. The diffraction losses depend heavily on rod diameter, resonator length and RoC of the resonator mirrors. LASCAD™ beam propagation method (BPM) resulted in a negligible diffraction loss when HR1064 nm end mirror and PR1064 nm output mirror, all with RoC = ∞, were placed very close to the laser rod. Final round-trip loss of 1.4% was calculated. Consequently, 13.96 W multimode solar laser power was numerically obtained, as shown by Fig. 3.38.
By considering the incoming solar power of 565.9 W and for the maximum solar laser output power of 13.96 W, solar-to-laser conversion efficiency of 2.47% was calculated for the closely coupled resonant cavity. Effective threshold solar pump power of 9.7 W and maximum effective solar power of 48.3 W was calculated, corresponding to 113.7 W threshold solar power and 565.9 W maximum incoming solar power, respectively. Solar laser slope efficiency of 3.09% was hence calculated. Maximum pump power/ threshold pump power ratio of 4.98 was calculated. All the above mentioned parameters are indicated in Table 3.6.
Similarly, for the laser resonator with L = 120 mm length, as shown in Fig. 3.39 and under the same pumping condition, 12.26 W laser output power, 106.8 W threshold pump power, 2.17% solar-to-laser conversion efficiency, 2.67% laser slope efficiency and 5.30 maximum pump power/threshold pump power ratio were calculated by LASCAD© software, as shown in Table 3.6. (See Chaps. 2 and 5 for Zemax® and LASCAD™ laser power calculation methods for the solar laser with definite resonant cavity).
3.28.4 Comparison of Different Analyses for the End-Side-Pumped Solar Laser
Discussions
As shown by Table 3.6, both the modified and the LASCADMax analyses predicted nearly the same amount of maximum extractable multimode laser power and solar-to-laser conversion efficiency when a PR1064 nm output mirror was closely placed near the Nd:YAG laser rod. This happened when \(\eta_{B} = 1\) overlap efficiency was assumed in the modified analysis. Classical analysis offered a slightly reduced accuracy in laser output power and efficiency predictions, as shown by Table 3.6.
It is important to point out that both the modified and the classical analyses were not effective in predicting the output power from a laser resonant cavity with a certain cavity length L \((\eta_{B} < 1)\), since it was very difficult to calculate analytically the beam overlap efficiency of solar pumped solid-state lasers, as mentioned in Sect. 3.22.
Zemax® and LASCAD™ analyses, however, were effective in the laser output power prediction of a solar laser with certain cavity length. Detailed analysis method will be provided in Sect. 6.2.1 of Chap. 6.
When the PR1064 nm output mirror was positioned 120 mm away from the rod, there was a noticeable reduction in beam overlap efficiency \((\eta_{B} < 1)\), consequently, 12.26 W solar laser power was numerically calculated by Zemax® and LASCAD120 mm analyses, as shown by Fig. 3.39 and confirmed by experimental result [14]. As for the prediction of threshold solar pump power, all the analyses failed to a considerable extent, leading normally to a much smaller threshold power prediction, as compared to the experimental value in Table 3.6.
References
Svelto, O.: Principles of Lasers, 5th edn. Springer, New York, NY (2016). https://books.google.pt/books/about/Principles_of_Lasers.html?id=ioywRI5W2HEC&redir_esc=y
Koechner, W.: Solid-State Laser Engineering, 6th edn. Springer, Berlin Heidelberg (2006). https://springerlink.bibliotecabuap.elogim.com/book/10.1007/978-3-662-14219-6
Yariv, A., Gordon, J. P.: The Laser*. Proceedings of the IEEE (1963). https://www.mindat.org/reference.php?id=12781943
Renk, K. F.: Basics of Laser Physics, 2nd edn. Springer Science & Business Media (2012). https://books.google.pt/books/about/Basics_of_Laser_Physics.html?id=dpVDTLPySTQC&redir_esc=y
Haken, H.: Laser Theory. Springer, Berlin Heidelberg (1984). https://books.google.pt/books/about/Laser_Theory.html?id=wzLtCAAAQBAJ&redir_esc=y
Siegman, A.E.: Lasers. University Science Books, Mill Valley, CA (1986). https://books.google.pt/books/about/Lasers.html?id=1BZVwUZLTkAC&redir_esc=y
Dickson, L.: Characteristics of a propagating gaussian beam. Appl. Opt. 9, 1854–1861 (1970). https://opg.optica.org/ao/abstract.cfm?uri=ao-9-8-1854
Stoehr, H., Mensing, F., Helmcke, J., Sterr, U.: Diode laser with 1 Hz linewidth. Opt. Lett. 31, 736–738 (2006). https://opg.optica.org/ol/abstract.cfm?uri=ol-31-6-736
Mandel, L.: Photon degeneracy in light from optical maser and other sources*. J. Opt. Soc. Am. 51, 797–798 (1961). https://opg.optica.org/josa/abstract.cfm?uri=josa-51-7-797
Hwang, I. H., Lee, J. H.: Efficiency and threshold pump intensity of CW solar-pumped solid-state lasers. IEEE J. Quantum Electron. 27(9), 2129–2134 (1991). https://ieeexplore.ieee.org/document/135171
Laporta, P., Magni, V., Svelto, O.: Comparative study of the optical pumping efficiency in solid-state lasers. IEEE J. Quantum Electron. 21(8), 1211–1218 (1985). https://ieeexplore.ieee.org/document/1072800
Barnes, N. P. Solid state laser from an efficiency perspective. IEEE J. Sel. Top. Quantum Electron. (June 2007). https://ieeexplore.ieee.org/document/4244407
Liang, D., Vistas, C. R., Garcia, D., Tibúrcio, B. D., Catela, M., Costa, H., Guillot, E., Almeida, J.: Most efficient simultaneous solar laser emissions from three Ce:Nd:YAG rods within a single pump cavity. Sol. Energy Mater. Sol. Cells. 246, 111921 (2022). https://www.sciencedirect.com/science/article/abs/pii/S0927024822003403#!
Liang, D., Almeida, J.: Highly efficient solar-pumped Nd:YAG laser. Opt. Express 19, 26399–26405 (2011). https://opg.optica.org/oe/fulltext.cfm?uri=oe-19-27-26399&id=225792
Weksler, M., Shwartz, J.: Solar-pumped solid-state lasers. IEEE J. Quantum Electron. 24(6), 1222–1228 (1988). https://ieeexplore.ieee.org/document/247
Lando, M., Kagan, J., Linyekin, B., Dobrusin, V.: A solar-pumped Nd:YAG laser in the high collection efficiency regime. Opt. Commun. 222, 1 (2003). https://www.sciencedirect.com/science/article/abs/pii/S0030401803016018
Author information
Authors and Affiliations
Corresponding author
Appendices
Homework with Solution 1
3.1.1 Calculation of Resonant Modes Numbers within a Cavity
Solution
For a single plane wave: \(\mathop{E}\limits^{\rightharpoonup} \left( {\mathop{r}\limits^{\rightharpoonup} ,t} \right) = \overset{\lower0.5em\hbox{$\smash{\scriptscriptstyle\rightharpoonup}$}}{{E_{0} }} e^{{i2\pi \nu t - i\overset{\lower0.5em\hbox{$\smash{\scriptscriptstyle\rightharpoonup}$}}{k \cdot } \mathop{r}\limits^{\rightharpoonup} }}\).
Where \(\overset{\lower0.5em\hbox{$\smash{\scriptscriptstyle\rightharpoonup}$}}{{E_{0} }}\) is field amplitude, \(\nu\) is light wave frequency, \(\mathop{r}\limits^{\rightharpoonup}\) is space coordinate vector and \(\mathop{k}\limits^{\rightharpoonup}\) is light wave vector. In free space, \(\mathop{k}\limits^{\rightharpoonup}\) can be any value. However, in hollow cavity, “ν” are with bounding limitations, only discrete values can exist. We consider stationary waves within a cubic hollow cavity (Fig. 3.40).
We therefore obtain
where: m, n, q can be any integers
For \(k = \frac{2\pi }{\lambda }\) the three components of k should meet the following conditions (Fig. 3.41)
The interval between modes can hence be calculated
Each mode occupies a unit volume element in “k” space (Fig. 3.42)
In \(\mathop{k}\limits^{\rightharpoonup}\) space, the volume between \(\left\lfloor {\overset{\lower0.5em\hbox{$\smash{\scriptscriptstyle\rightharpoonup}$}} {k} } \right\rfloor\) and \(\left\lfloor {\overset{\lower0.5em\hbox{$\smash{\scriptscriptstyle\rightharpoonup}$}} {k} } \right\rfloor + d\left| {\mathop{k}\limits^{\rightharpoonup} } \right|\) is:
Therefore, the number of modes within \(\left\lfloor {\overset{\lower0.5em\hbox{$\smash{\scriptscriptstyle\rightharpoonup}$}} {k} } \right\rfloor\) and \(\left\lfloor {\overset{\lower0.5em\hbox{$\smash{\scriptscriptstyle\rightharpoonup}$}} {k} } \right\rfloor + d\left| {\mathop{k}\limits^{\rightharpoonup} } \right|\)
Since
Also since there are two modes (spin angular momentum of \(\left( { \pm \hbar } \right)\)) possible for each value of k, the total number of modes within \(\upsilon \leftrightarrow \upsilon + d\upsilon\)
where V is the volume of the cavity. \(\rho \left( \nu \right)\) is defined as the number of modes per unit volume and per unit frequency range, the number of mode per unit volume per unit frequency is therefore calculated.
Homework with Solution 2
3.2.1 Deriving Solar Spectral Irradiance from Planck’s Law
In experimental work, solar irradiance distribution as a function of wavelength is preferred and the radiation law take the form
Please deduce solar spectral irradiance (3.22) from Planck’s law (3.21)
Solution
By considering energy inavariance in wavelength and frequency domains
then
Since
then
Since full solid angle equals 4π,
Planck’s formula per Steradian is therefore obtained by dividing (3.21) by \(4\pi\).
Consequently, \(\rho \left( {\lambda ,T} \right)\) can be deduced from \(\rho \left( {\upsilon ,T} \right)\)
Solar spectral irradiance \(I\left( \lambda \right)\) can be obtained by multiplying (3.183) by c
Consequently, we obtain solar spectral irradiance as a function of wavelength \(\lambda\) (as well as temperature \(T\))
Homework with Solution 3
3.3.1 Deriving Stefan-Boltzmann’s Law from Planck’s Law
Please deduce Stefan-Boltzmann’s law (3.25)
from Plank’s formula (3.21)
Solution
Plank’s formula in terms of photon irradiance
Total photon irradiance \(I\) over the whole frequency spectrum
If we assume
For 4π solid angle
Since
Radiation constant \(\sigma=\ \frac{1}{4}\sigma'\) of Stefan-Boltzmann’s law can be calculated
according to 2019 redifinition of SI base units
Homework with Solution 4
3.4.1 Deriving Wien’s Displacement Law from Planck’s Law
Please deduce Wien’s displacement law (3.27)
from Planck’s law (3.22)
Solution
By taking derivative of \(\rho \left( \lambda \right)\) with respect to \(\lambda\):
Peak \(\rho \left( \lambda \right)\) can be found by applying
Then
Finally
If we assume
Then:
where \(x = 4.965\) equalize both side of the above equation.
Consequently
Which happens when \(\lambda = \lambda_{{{\text{max}}}}\)
Wien’s displacement law is finally deduced
Rights and permissions
Copyright information
© 2023 The Author(s), under exclusive license to Springer Nature Switzerland AG
About this chapter
Cite this chapter
Liang, D. (2023). Solar-Pumped Solid-State Laser Theory. In: Solar-Pumped Lasers. Green Energy and Technology. Springer, Cham. https://doi.org/10.1007/978-3-031-24785-9_3
Download citation
DOI: https://doi.org/10.1007/978-3-031-24785-9_3
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-031-24784-2
Online ISBN: 978-3-031-24785-9
eBook Packages: EnergyEnergy (R0)