Abstract
Intensive mining and processing of Ag, Sn, Pb and Zn ores have occurred in various locations within and around the city of Potosí, Bolivia since 1545. Surface and subsurface waters, stream sediments and soils are contaminated with various ecotoxic metals in the headwaters of the economically vital, yet highly impacted, upper Rio Pilcomayo watershed. Previous studies have documented downstream trace metal contamination, however, not addressed specific sources. The AMD discharges identified in this study help link downstream pollution to primary origins. The majority of AMD would be considered high-strength due to metal concentrations and acidity orders of magnitude greater than typical AMD. Discharges from both operating and abandoned portals as well as tailings-related deposits displayed a high degree of heterogeneity with total metal concentrations ranging from 0.11 to 7480, <0.022 to 889, <0.0006 to 65.3, <0.001 to 310, 0.12 to 72,100, 0.3 to 402, <0.012 to 34.8, and 0.24 to 19,600 mg/L of Al, As, Cd, Cu, Fe, Mn, Pb and Zn, respectively. Net acidity and pH ranged from −10 to 246,000 mg/L as CaCO3 equivalent and 0.90–6.94 standard units, respectively. Data were gathered during two sampling events centered around the most extreme periods of the dry and wet seasons of one water-year. Loadings to local streams were marginally greater for most metals in the wet season. If observed loadings are historically representative, Cerro Rico AMD has contributed thousands of tonnes of ecotoxic metals to the upper Rio Pilcomayo over the last five centuries. Metal and hydrogen ion concentrations in the majority of AMD sampled were several orders of magnitude above discharge limits set by the Bolivian government, yet no action has historically or contemporarily been taken.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
Historical background
Twelve years after Pizarro dethroned Atahualpa and conquered the Inca, the largest Ag deposit in the world was discovered at Cerro Rico (Rich Hill) by the indigenous nobleman Diego Huallpa. The next year the Spanish founded the city of Potosí at Cerro Rico’s base with Huallpa’s confidant, the Spaniard Juan de Villarroel, registering the first claim in 1545 (Wilson and Petrov 1999). Within a hundred years Potosí became one of the world’s richest and most populous cities during a boom fueled by veins of up to 25% pure Ag (Wilson and Petrov 1999; Bartos 2000; Abbot and Wolfe 2003; Waltham 2005). Mining has proceeded nearly continuously over the last five centuries and it is estimated that between 20,000 and 40,000 tonnes of Ag were produced from 1545 to 1824 and over 10,000 tonnes from 1824 to present (Lindgren 1928; Zartman and Cunningham 1995; Pretes 2002; Abbot and Wolfe 2003). Abbot and Wolfe (2003) also postulate that thousands of tonnes of Ag were produced from Cerro Rico and nearby deposits in Pre-Colombian times before and after the Incan conquest from the 10th to the 15th centuries. Ores from Potosí subsidized Spanish military expansionism while millions of forced indigenous and enslaved African laborers died premature deaths mining the depths of Cerro Rico and processing the ores found within (Galeano 1971; Tandeter 1981; Bakewell 1984). Ag, Sn, Pb and Zn have been the primary metals mined and processed in and around the slopes of Cerro Rico, sustaining the city economically for centuries. However, the environmental cost of Potosí’s good fortune has been steep. Terrestrial zones have experienced extreme deforestation and associated soil loss (Godoy 1985). Local watercourses have been impacted by mineral processing effluent and unmitigated acid mine drainage (AMD).
Acid mine drainage
Economically valuable geologic deposits such as coal and metal ores are normally chemically stable under undisturbed in situ conditions. AMD forms when isolated sulfide minerals, such as pyrite (FeS2), sphalerite (ZnS) and galena (PbS), are exposed to oxygen and water (Younger et al. 2002). Microbes such as Acidithiobaccillus ferrooxidans increase the rate of AMD evolution by catalyzing mineral oxidation (Younger et al. 2002). This mineral oxidation creates and mobilizes free metal, SO4 2− and hydrogen ions into solution (Eqs. 1–5):
Pyrite oxidation (Eqs. 1–4) is the primary agent of AMD formation. The acidity generated by pyrite oxidation lowers the pH, increasing the solubility of many metals and allowing faster weathering of other metal sulfides. Weathering of other metal sulfides will not necessarily produce acidity, but will release metal ions to solution (Younger et al. 2002). Sphalerite oxidation (Eq. 5) is an example of these reactions which may release Zn, Pb, Ni, Cd, Cu, As and other ecotoxic metals to solution often to be transported to discharge points such as seeps, adits or boreholes which then impact downstream environments (Younger et al. 2002).
The environmental cost of AMD has been known for centuries. The man considered to be the founder of geology as a discipline, Georgius Agricola, stated in the 16th century that “…when the ores are washed, the water which has been used poisons the brooks and streams, and either destroys the fish or drives them away” (Agricola 1556). The ecotoxic metal ions, acidity and resultant precipitates (such as iron oxyhydroxide often referred to as ochre) associated with AMD are a significant threat to freshwater resources and can cause fish-kills and lasting degradation of aquatic habitats (Adams and Younger 2001; Younger et al. 2002). AMD also often renders receiving watercourses unfit for use as water resources (Adams and Younger 2001).
Geologic setting
Cerro Rico de Potosí was created by volcanic eruptions of the Tertiary Age. It lies within a Neogene-Quaternary volcanic-plutonic complex stretching for approximately 800 km along the Eastern Cordillera of the Andes (Zartman and Cunningham 1995; Kamenov et al. 2002). Ore occurs throughout systems of veins in a conical dacitic volcanic dome rising 700 m above the city of Potosí (Zartman and Cunningham 1995). Argentiferous magma crystallized into cassiterite-rich veins formed in Ordovician slate, dacitic tuff and tuff breccia, and other dacitic stock (Griess 1951; Brading and Cross 1972; Rice and Steele 2005). The veins are enclosed in zones of metal sulfides, oxides and gangue minerals such as quartz, tourmaline, siderite and kaolinite. Silver oxides predominated in the upper altitudes of Cerro Rico while Ag sulfide ores dominate in the lower reaches (Bartos 2000). Host rock is pyritized near the veins and pyrite is the predominant associated mineral with the sulfide ores and country rock (Lindgren 1928; Lindgren and Creveling 1928; Petersen 1945; Wilson and Petrov 1999). Pyrite is the prime driver of AMD formation and its pervasiveness indicates that AMD will be released to the surrounding areas for decades or centuries unless remedial actions are undertaken. The polymetallic nature of the orebody indicates that this AMD would likely contain elevated concentrations of multiple metals of concern.
Legacy
The history of Potosí, like many historic mining centers, is one of cyclical boom and bust that has likely maximized AMD evolution. Many local mines have been abandoned, flooded, dewatered and mined again multiple times (Hillman 1984), following the rise and fall of ore prices. There is evidence from Pb-contaminated lake sediments that mining and smelting for Ag production may have begun at Cerro Rico around 1000 A.D (Abbot and Wolfe 2003). However, intensive mining did not begin until Spanish conquest. Cerro Rico is considered the world’s largest Ag deposit and Potosí led the world in production during the 16th and 17th centuries (Lofstrom 1970; Zartman and Cunningham 1995; Bartos 2000; Rice and Steele 2005). After an initial boom fueled by Ag oxide ores of up to 25% purity, mining lulled from approximately 1555 to 1575 until the introduction of the Hg amalgamation process (Serrano et al. 1996; Wilson and Petrov 1999). Ag production peaked in the late 16th century when there were over 600 mines on the mountain working a vertical interval of approximately 250 m (Serrano et al. 1996; Waltham 2005). Production lulled yet again from approximately 1700 to 1745 (Serrano et al. 1996). After a resurgence from approximately 1745 to 1805, production fell precipitously so that by 1825 Cerro Rico was home to more than 5,000 open mine shafts and adits, most of which were abandoned, flooded or collapsed (Lofstrom 1970). Of those shafts, only 50–60 were in use and the lower majority of the mountain was flooded (Lofstrom 1970). In the 1800s Potosí’s population had fallen from a maximum of approximately 160,000 during the Ag boom of the 1600s to about 10,000 (Pretes 2002).
Resurgence of the Ag industry from 1850 to 1873 enabled by lower Hg prices (Hg was used in the amalgamation technique for processing Ag sulfides) caused the short-lived dewatering and re-start of many mines (Hillman 1984). In the latter quarter of the 1800s, Potosí’s fortunes rebounded yet again with the emergence of the Sn industry as the Ag industry declined (Hillman 1984). An indication of the rich polymetallic nature of the Cerro Rico ore body, another metal, Cu, was mined and processed in the early 1900s (Miller and Singewald 1919; Cunningham et al. 1996). As of 1928, many veins in Potosí had been worked over a vertical interval of approximately 600 m (Lindgren 1928). The pinnacle of the Sn industry was in the first half of the 20th century when Bolivia was one of the top three worldwide producers during World War II (Griess 1951). Although the Sn industry was first established by the Incas, Sn only surpassed Ag in economic importance around the turn of the 20th century (Hillman 1984; Godoy 1985). At this time Sn miners dewatered and worked former Ag mines as well as alluvial deposits (pallacos) at the base of Cerro Rico (Bartos 2000; Waltham 2005). However, the 1985 Sn price collapse caused the closure and flooding of many Potosí mines (Waltham 2005; Younger 2007). Mineral prices have risen in recent years, leading to yet another boom cycle of dewatering and ore exploitation. In 1996, Serrano et al. (1996) reported that over 500 shafts and adits were in operation, worked by about 5,000 miners. As of 2000, mine workings had extended to a vertical interval of 1,150 m (Bartos 2000). Currently, it is estimated that approximately 20,000 miners are either reworking old tailings and mine workings or opening new workings in deeper zones of Cerro Rico mining primarily Pb and Zn ores, and to a lesser extent, Ag and Sn ores. The repeated flooding, dewatering and mining of Cerro Rico has likely led to near-continuous production of high-strength AMD for centuries as freshly exposed sulfide minerals contact water during non-operational periods. The subsequent dewatering allows for oxygen ingress and fresh mineral exposure as the cycle is repeated.
Broad and progressive Bolivian environmental regulations became law in 1992 (BMSDP 2000). The law (Number 1333) regulates pollutant discharges of nearly all industries, sets water quality standards for receiving bodies and establishes limits for liquid discharges. However, it appears to have been largely ignored by the mining industry (Garcia-Guinea and Harffy 1998). Article 45 of the Bolivian Mining Code states that mining operations should use systems and technology compatible with environmental protection (Bocangel 2001). The Bolivian government issued and widely publicized Supreme Decree 25419, requiring all mining operations to obtain an environmental license (Bocangel 2001). Supreme Decree 25877 extended the deadline for compliance and has also met very limited success (Bocangel 2001). It is likely that, in addition to discharging AMD and mineral processing effluent out of compliance with Bolivian law, many mining facilities have not acquired an environmental license.
Previous environmental studies
Intensive mining over several centuries has devastated the aquatic environment around Potosí. Hudson-Edwards et al. (2001), Smolders et al. (2002, 2003, 2004), Miller et al. (2002, 2004) and Archer et al. (2005) documented dissolved and total ecotoxic metal concentrations orders of magnitude greater than natural background levels in Rio Tarapaya from the western edge of Potosí’s city limits to ~500 km downstream in Rio Pilcomayo. Miller et al. (2002, 2007) linked this contamination to mining activity via isotopic analysis of Pb in river sediment, however, the specific contaminant sources (i.e., AMD, mineral processing effluent, tailings dam erosion, etc.) could not be identified.
Although downstream heavy metal contamination has been fairly well documented, contamination sources have not. No peer-reviewed studies of Cerro Rico AMD or the other probable ecotoxic metal sources have been encountered in the literature. The objectives of the study were to catalog the AMD discharges of Cerro Rico, determine the extent to which these discharges may be out of compliance with Bolivian law, and estimate metal loading rates to streams in the local watershed.
Methods
Study area
The study centered around Cerro Rico, approximately 1 km south of the city of Potosí, Bolivia. Potosí (19.585°S 65.754°W) lies in the Eastern Cordillera range of the Central Andes in the upper reaches of the Rio Pilcomayo watershed. As the entirety of Cerro Rico and immediate environs can essentially be considered a mine, all groundwater discharges noted were classified as AMD. AMD identified and characterized were from active and abandoned mine portals of Cerro Rico and seeps influenced by tailings deposits and/or the mineral-rich pallacos at the northwest base of Cerro Rico (Figs. 1, 2). The AMD documented in this study are those which were flowing during Potosí’s dry season of July/August 2006 and wet season of March 2007 and those not intercepted for mineral processing use. Innumerable working and abandoned mine portals dot Cerro Rico, however, the majority were observed to not produce effluent. Active mine portal, abandoned portal, and tailings-related discharges were assigned the prefixes “C”, “A” and “T”, respectively. Of the thirteen AMD sources identified and characterized on Cerro Rico proper, seven were from active mine portals, five were from abandoned portals and one was from a tailings deposit. Three tailings-related AMD sources were located at the northwest base of Cerro Rico.
Discharges 1A, 3A, 4T and 1–4C (Fig. 1) drain to Rio Huayna Mayu which empties into the highly polluted Ribera de la Vera Cruz, which also contains residual tailings from past mineral processing plant discharges and raw sewage from the city. Discharges 2A, 4–5A and 6C drain to Quebrada Chimborazo which shortly thereafter confluences with Rio Villacollu Mayu. Discharge 5C drains to the highly impacted Rio Jayac Mayu (“spicy river” in Quechua, the language of the Inca) which also may receive diffuse acid rock drainage (ARD) from numerous waste rock piles near its source. Discharge 7C drains to Rio Sucu/Kori Mayu which also receives AMD from the pallacos zones (discharges 1–3T). The pallacos discharges are associated with natural and anthropogenic erosion of mineral-rich material from Cerro Rico and the tailings from Sn mining of that material that ceased decades ago (Bartos 2000; Waltham 2005). These sources are also likely influenced by groundwater seepage from the San Miguel tailings deposit, which lies between Rio Sucu/Kori Mayu and the Ribera de la Vera Cruz. The Pailaviri tailings deposit (discharge 4T) on the slope of Cerro Rico drains to Huayna Mayu (Fig. 2). A few AMD sources (7C, 4A, 5A and 4T) were only sampled in the wet season because they were not flowing during the dry season.
Data collection
Water quality parameters and grab samples were obtained at the points indicated on Fig. 1 during the dry (July 27 to August 14, 2006) and wet (March 11–23, 2007) seasons of one water-year (Fig. 3). These intervals were chosen in an attempt to capture the groundwater level/efflux and surface water flow extremes of both seasons, when are near their minima (dry) and maxima (wet). Sampling periods were offset from the minima and maxima of the monthly average precipitation because of the common response lag of groundwater level/efflux and surface water flows to precipitation events (Eltahir and Yeh 1999).
The location of each AMD discharge was recorded with a Garmin® GPS unit. Alkalinity titrations were conducted in the field following standard methods (APHA 1998). Temperature, pH, dissolved oxygen (DO) and specific conductance (SC) were determined in the field using a properly calibrated Orion 1230 multimeter. The Orion pH probe consisted of a gel-filled epoxy body with an Ag–AgCl internal reference, wick junction and standard glass bulb. The pH was calibrated with Thermo Scientific pH 4.00, 7.00 and 10.00 standards for a three-point calibration, which is suitable for pH 2–10 (Cheng and Zhu 2005). All grab samples were taken using 125-mL HDPE containers for subsequent analysis at the University of Oklahoma Center for Restoration of Ecosystems and Watersheds (CREW) laboratories. Samples for anion analyses were stored at 4°C until filtered through 0.2 μm nylon filters and Dionex OnGuard® II H cartridges. A MetrOhm® 761 ion chromatograph unit was used to quantify SO4 2− concentrations following United States Environmental Protection Agency (USEPA) method 300. Total metal samples were immediately preserved with concentrated nitric acid and stored at 4°C until microwave acid digestion. Upon collection, dissolved metal samples were immediately filtered through 0.45 μm nylon filters then preserved with concentrated nitric acid and stored at 4°C until microwave acid digestion. All microwave acid digestions followed USEPA method 3015. Digested metal samples were filtered through 0.45 μm nylon filters then analyzed via a Varian Vista-Pro® simultaneous inductively coupled plasma-optical emission spectrometer following EPA method 6010. Following USEPA methods, duplicate and/or triplicate digestions of metal samples and measurements for metals and sulfate concentrations were randomly obtained for quality assurance and control. Net acidity was calculated following a modified version of that presented by Younger et al. (2002), which accounted for the acidity from the substantial Cd2+, Cu2+ and Zn2+ concentrations present in these unique waters. Hedin (2006) demonstrated an excellent relationship between calculated and measured net acidity for a diverse data set of 1,484 AMD sources.
Flow rates (Q) were obtained via two methods. When possible, flow rates were obtained by building temporary weirs and determining time to gather a known volume in a bucket or graduated cylinder. When flow rates were greater than this method would allow, discharge was estimated by determining channel cross-section, depth and velocity as approximated by floating a partially submersible object a given distance. Wet and dry season loadings were determined by multiplying total metal concentrations by their respective flow rates. Where flow rates were too low or diffuse to determine using the aforementioned methods, a conservative flow rate of 0.01 L/s based on comparative observation was assigned to enable the prudent estimation of metal loadings.
Results and discussion
Physiochemical parameters, total and dissolved metal concentrations, and SO4 2− concentrations for sampled AMD are presented in Tables 1 and 2. These results are compared to various water quality criteria set by the Bolivian government in Table 3. Generally, dissolved metal concentrations were similar to total metal concentrations, indicating that the bulk of metals discharged to receiving streams from mine water discharges are in the more mobile, dissolved form. Metals and SO4 2− concentrations and acidity in AMD varied by several orders of magnitude, indicating a high degree of heterogeneity within the groundwaters of Cerro Rico. Metals are not uniformly disseminated throughout Cerro Rico which is reflected by these data. The majority of AMD would be considered high-strength due to metal concentrations and acidity orders of magnitude greater than typical AMD (e.g., Younger et al. 2002; Watzlaf et al. 2004). Concentrations of contaminants in most sampled AMD were orders of magnitude out of compliance with Bolivian discharge limits and likely contributed to the aforementioned pollution downstream.
The active mine portals generally had higher metal concentrations than the abandoned and tailings-related sources (Table 2). The tailings-impacted pallacos discharges (1-3T) generally exhibited lower metal concentrations than the other abandoned and active mine sources. This is likely due to the increased weathering that the alluvial deposits have experienced. These deposits were created over millennia as surface rock of Cerro Rico weathered and eroded downhill. Much of the sulfides on the exposed surfaces of the alluvial deposits have likely been weathered, leaving more inert material that produces AMD or ARD of lower metal concentrations and acidity. The freshly exposed sulfides within Cerro Rico are likely leading to the higher metal concentrations observed in the AMD of the active mines. Cerro Rico has been mined for centuries at irregular unsystematic intervals and many workings are interconnected due to the degree of exploration and common collapse features (Petersen 1945; Cunningham et al. 1996). The active mine portals shared the same general pH and metal concentrations as three of the abandoned portals (1–3A). The abandoned mine portals sampled in this study are likely connected to and receive waters from active workings, thus sharing in the effect of the ongoing fresh sulfide mineral exposure and oxidation.
The seep from the Pailaviri tailings deposit (4T) produced the most acidic and metal-laden AMD identified. The pH and metal concentrations of this seep place it among other extreme examples of AMD. Dissolved As, Fe and SO4 2− concentrations rival those documented at Iron Mountain, which as of 1999 was reported to have the greatest concentrations of these constituents ever recorded in groundwater (Nordstrom and Alpers 1999; Nordstrom et al. 2000). Other sites with acute AMD, the Iron Duke mine in Zimbabwe and Peña de Hierro in Spain, demonstrated similar extreme elevated concentrations of Al, Cd and/or Mn as the Pailaviri seep (Williams and Smith 2000; Romero et al. 2011). Iron Mountain, Iron Duke, and Peña de Hierro are examples of the most ideal geologic settings for AMD production in the world. The Pailaviri tailings deposit must present a similar geologic setting, and thus a major environmental liability.
The AMD documented in this study are contributing to the downstream violations of Bolivian receiving body water quality limits noted in the following chapter. Class “D” is the lowest designation of Bolivian receiving water bodies in which industrial applications and navigation are the only suitable uses except in extreme circumstances (BMSDP 2000). Bolivian law states that class “D” waters must be “coagulated, flocculated, filtered and disinfected” prior to domestic use (BMSDP 2000). It is not known how or if the water bodies downstream of Potosí are designated. However, they are used for agriculture and therefore should be rated at a minimum above class D. The introduction of AMD with concentrations of Al, As, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, Zn and SO4 2− orders of magnitude greater than class “D” limits is contributing to non-compliance downstream.
All but one of the AMD discharges (4A) exceeded Bolivian monthly discharge limits to some degree and most by orders of magnitude for multiple metals. Half of the sixteen AMD discharges had higher than permissible concentrations of As, Cd, Cu, Fe, Pb and Zn. Fourteen AMD discharges had higher than permissible Zn concentrations, often by three or four orders of magnitude. Thirteen had lower than permissible pH. The data support the assertion of Garcia-Guinea and Harffy (1998) that Bolivian environmental law “has been sadly ignored where mining is concerned.”
Local streams were considerably loaded with ecotoxic metals from Cerro Rico (Table 4). Active mine portals contributed the majority of metal loadings in both seasons. All metal loadings except Cd, Cu and Zn were at least marginally greater during the wet season. Combined Al, As, Fe, Mn, Ni and Pb loadings were 26, 12, 88, 76, 45 and 57% greater, respectively, in the wet season. Tailings-related discharge loadings were much greater in the wet season when 4T was flowing. The majority of AMD discharges had concentrations of As, Cd, Cu, Pb and Zn orders of magnitude higher than those found downstream in Rio Tarapaya and Rio Pilcomayo by earlier studies (e.g., Hudson-Edwards et al. 2001; Smolders et al. 2003). Overall, the data indicate that these AMD discharges are contributing to some degree to downstream heavy metal pollution in the upper Rio Pilcomayo basin, which is further demonstrated in Strosnider et al. (2011a). If observed loadings are historically representative, AMD has contributed thousands of tonnes of ecotoxic metals to the upper Rio Pilcomayo over the last five centuries. Nonpoint source ephemeral ARD sources also exist, due to the prevalence of innumerable ancient and recent ore and tailings dumps upon and around Cerro Rico (Miller and Singewald 1919; Lindgren and Creveling 1928; Francis et al. 1981), exposure of ores near the peak with recent and ongoing surface mining, as well as the highly mineralized nature of Cerro Rico’s slopes. Despite efforts to locate all AMD sources around Cerro Rico, other point sources likely exist because of the size of Cerro Rico and dynamic nature of ongoing mining. The likelihood of other AMD sources renders downstream loadings documented in this study a probable underestimate.
The relative importance of different pollution sources to the Rio Pilcomayo is unknown. Hudson-Edwards et al. (2001), Smolders et al. (2002, 2003) and Miller et al. (2002, 2004, 2007) stressed the significance of mineral processing effluent to downstream contamination. However, these studies were undertaken when the tailings load to the upper Rio Pilcomayo was much greater, before the construction of the Laguna Pampa and San Antonio tailings dams which are now the destination of most mineral processing effluent. In addition, no published peer-reviewed studies have documented the mineral processing effluent characteristics and loading rates. This study is the first to characterize AMD sources. However, the data presented in this study were the minimum required to extrapolate annual loading to downstream watercourses, and are likely an underestimate of the total loading from point AMD sources because of the probable existence of other sources. Further research, including mineral processing effluent discharge and nonpoint ARD characterization will help solidify the relative importance of the upper Rio Pilcomayo’s pollution sources. This information would help establish priorities for future remediation efforts.
The extraction and export of mineral wealth has dominated the economy of Bolivia for centuries. Potosí’s economy and roughly 150,000 residents remain heavily dependent upon mineral extraction and processing. Therefore, environmental law enforcement should be carefully applied and fitting solutions presented to lessen the impact of mining operations. Measured by multiple metrics, Bolivia is one of the poorest nations in the Western Hemisphere (World Bank 2009). Hence, solutions attempted to address to the mine water pollution problems in Potosí cannot be capital-intensive. A labor-intensive solution may be desirable because of high unemployment and underemployment in Potosí, as well as the low cost of local labor.
Passive systems may be more suitable than active systems for AMD treatment in Potosí. Passive treatment uses unrefined natural materials to promote natural chemical and biological processes to improve water quality (Younger et al. 2002). Active treatment, the improvement of water quality by methods that require ongoing inputs of energy and chemical reagents, generally has higher operational costs than passive systems (Younger et al. 2002). Highly mechanized construction or operational activities are not desirable in Potosí because of logistical and supply issues. In developed nations, passive treatment systems have higher up-front costs because of greater land and construction expenses (Younger et al. 2002). However, in Bolivia depressed land and low construction costs may make passive treatment a logical solution from both long- and short-term perspectives. The chemicals, electricity and equipment needed for active treatment may make passive treatment by default the most applicable solution. In addition, passive treatment system construction and metal reclamation could provide needed employment.
The two major raw materials often required for passive treatment systems are organic substrate and limestone. Locally available limestone is suitable for passive treatment (Strosnider and Nairn 2010). Results from Santamaria et al. (2009) indicate that locally available llama dung, cattle manure, and brewery waste are suitable for use in passive treatment. Conventional hybrid active–passive treatment systems are also a more sustainable option. The passive co-treatment of Potosi’s AMD with municipal wastewater is also a less conventional option that has been recently proved feasible (Strosnider and Nairn 2010; Strosnider et al. 2011b, c).
Conclusions
The AMD of Cerro Rico de Potosí can generally be categorized as high-strength, with concentrations of various ecotoxic metals often orders of magnitude greater than discharge limits. If the loadings observed are historically representative, AMD has been a prime contributor of ecotoxic metals to the upper Rio Pilcomayo over the last five centuries. Yet, no action has been taken to address these discharges, neither historically nor contemporarily. Further studies, concerning the relative contributions of ecotoxic metal sources to the upper Rio Pilcomayo and treatability of these sources are recommended to refine remediation priorities and approaches.
References
Abbot MB, Wolfe AP (2003) Intensive Pre-Incan metallurgy recorded by lake sediments from the Bolivian Andes. Science 301:1893–1895
Adams R, Younger PL (2001) A strategy for modeling ground water rebound in abandoned deep mine systems. Ground Water 39(2):249–261
Agricola G (1556) De Re Metallica
American Public Health Association (APHA) (1998) Standard methods for the examination of water and wastewater, 20th edn. American Public Health Association, USA
Archer J, Hudson-Edwards KA, Preston DA, Howarth RJ, Linge K (2005) Aqueous exposure and uptake of arsenic by riverside communities affected by mining contamination in the Río Pilcomayo basin, Bolivia. Mineral Mag 69(5):719–736
Bakewell P (1984) Miners of the Red Mountain: Indian Labor in Potosí. The University of New Mexico Press, Albuquerque, pp 1545–1650
Bartos PJ (2000) The pallacos of Cerro Rico de Potosí, Bolivia: a new deposit type. Econ Geol Bull Soc Econ Geol 95:645–654
Bocangel D (2001) Small-scale mining in Bolivia: national study mining minerals and sustainable development. Mining, Minerals and Sustainable Development 71
Bolivian Ministry of Sustainable Development and Planning (BMSDP) (2000) Ley del Medio Ambiente—No. 1333.3
Bolivian National Meteorology and Hydrology Service (BSNMH) (2003) Meteorological bulletin of the department of Potosí
Brading DA, Cross HE (1972) Colonial silver mining: Mexico and Peru. Hispanic Am Hist Rev 52:545–579
Cheng KL, Zhu D (2005) On calibration of pH meters. Sensors 5:209–219
Cunningham CG, Zartman RE, McKee EH, Rye RO, Naeser CW, Sanjines VO, Ericksen GE, Tavera VF (1996) The age and thermal history of Cerro Rico de Potosi, Bolivia. Mineralium Deposita 31:374–385
Eltahir EAB, Yeh PJF (1999) On the asymmetric response of aquifer water level to floods and droughts in Illinois. Water Resour Res 35(4):1199–1217
Francis PW, Baker MCW, Halls C (1981) The Kari Kari caldera, Bolivia, and the Cerro Rico stock. J Volcanol Geotherm Res 10:113–124
Galeano E (1971) The open veins of Latin America. Monthly Review Press, New York
Garcia-Guinea J, Harffy M (1998) Bolivian mining pollution; past present and future. Ambio 27(3):251–253
Godoy RA (1985) Technical and economic efficiency of peasant miners in Bolivia. Econ Dev Cult Change 34:103–120
Griess PR (1951) The Bolivian tin industry. Econ Geogr 27:238–250
Hedin RS (2006) The use of measured and calculated acidity values to improve the quality of mine drainage datasets. Mine Water Environ 25:146–152
Hillman J (1984) The emergence of the tin industry in Bolivia. J Lat Am Stud 16:403–437
Hudson-Edwards KA, Macklin MG, Miller JR, Lechler PJ (2001) Sources, distribution and storage of heavy metals in the Rio Pilcomayo, Bolivia. J Geochem Explor 72:229–250
Kamenov G, Macfarlane AW, Riciputi L (2002) Sources of lead in the San Cristobal, Pulacayo, and Potosí mining districts, Bolivia, and a reevaluation of regional ore lead isotope provinces. Econ Geol 97:573–592
Lindgren W (1928) Mineral deposits. McGraw-Hill, New York
Lindgren W, Creveling JG (1928) The ores of Potosi, Bolivia. Econ Geol 23(3):233–262
Lofstrom W (1970) Attempted economic reform and innovation in Bolivia under Antonio Jose de Sucre, 1825–1828. Hispanic Am Hist Rev 50:279–299
Miller BL, Singewald JT (1919) The mineral deposits of South America. McGraw-Hill, New York
Miller JR, Lechler PJ, Hudson-Edwards KA, Macklin MG (2002) Lead isotopic fingerprinting of heavy metal contamination, Rio Pilcomayo basin, Bolivia. Geochem Explor Environ Anal 2:225–233
Miller JR, Hudson-Edwards KA, Lechler PJ, Preston D, Macklin MG (2004) Heavy metal contamination of water, soil and produce within riverine communities of the Rio Pilcomayo basin, Bolivia. Sci Total Environ 320:189–209
Miller JR, Lechler PJ, Macklin G, Germanoski D, Villarroel LF (2007) Evaluation of particle dispersal from mining and milling operations using lead isotopic fingerprinting techniques, Rio Pilcomayo Basin, Bolivia. Sci Total Environ 384:355–373
Nordstrom DK, Alpers CN (1999) Negative pH, efflorescent mineralogy, and consequences for environmental restoration at the Iron Mountain Superfund site, California. Proc Natl Acad Sci 96:3455–3462
Nordstrom DK, Alpers CN, Ptacek CJ, Blowes DW (2000) Negative pH and extremely acidic mine waters from Iron Mountain, California. Environ Sci Technol 34:254–258
Petersen EF (1945) Mining and development, Potosí, Bolivia. Mines Mag 35:19–20
Pretes M (2002) Touring mines and mining tourists. Ann Tour Res 29:439–456
Rice CM, Steele GB (2005) Duration of magmatic hydrothermal and supergene activity at Cerro Rico de Potosi, Bolivia. Econ Geol 100:1647–1656
Romero A, González I, Galán E (2011) Stream water geochemistry from mine wastes in Peña de Hierro, Riotinto area, SW Spain: a case of extreme acid mine drainage. Environ Earth Sci 62(3):645–656
Santamaria B, Apoza Q MR, Strosnider WH, Nairn RW (2009) Preliminary evaluation of locally available organic substrates for vertical flow passive treatment cells in Potosí, Bolivia. Proceedings of the 2009 American Society of Mining and Reclamation. Billings, Montana
Serrano C, Pelaez J, Bouso JL (1996) La Ribera de la Vera Cruz de Potosí. Rocas y Minerales 293:49–67
Smolders AJP, Guerrero Hiza MA, Van der Velde G, Roelofs JGM (2002) Dynamics of discharge, sediment transport, heavy metal pollution and sábalo (prochilodus lineatus) catches in the lower Pilcomayo river (Bolivia). River Res Appl 18:415–427
Smolders AJP, Lock RAC, Van der Velde G, Medina Hoyos RI, Roelofs JGM (2003) Effects of mining activities on heavy metal concentrations in water, sediment, and macroinvertebrates in different reaches of the Pilcomayo river, South America. Arch Environ Contam Toxicol 44:314–323
Smolders AJP, Hudson-Edwards KA, Van der Velde G, Roelofs JGM (2004) Controls on water chemistry of the Pilcomayo river (Bolivia, South-America). Appl Geochem 19:1745–1758
Strosnider WH, Nairn RW (2010) Effective passive treatment of high-strength acid mine drainage and raw municipal wastewater in Potosí, Bolivia using simple mutual incubations and limestone. J Geochem Explor 105:34–42
Strosnider WHJ, Llanos López FS, Nairn RW (2011a) Acid mine drainage at Cerro Rico de Potosí II: severe degradation of the upper Rio Pilcomayo watershed. Environ Earth Sci. doi:10.1007/s12665-010-0899-2
Strosnider WH, Winfrey BK, Nairn RW (2011b) Novel passive co-treatment of acid mine drainage and municipal wastewater. J Environ Qual 40:206–213
Strosnider WH, Winfrey BK, Nairn RW (2011c) Alkalinity generation in a novel multi-stage high-strength acid mine drainage and municipal wastewater passive co-treatment system. Mine Water Environ 30:47–53
Stumm W, Morgan JJ (1996) Aquatic chemistry–chemical equilibria and rates in natural waters, 3rd edn. Wiley-Interscience, New York
Tandeter E (1981) Forced and free labour in Late Colonial Potosí. Past Present 93:98–136
Waltham T (2005) The rich hill of Potosí. Geol Today 21(5):187–190
Watzlaf GR, Schroeder KT, Kleinmann RL, Kairies CL, Nairn RW (2004) The Passive Treatment of Coal Mine Drainage. United States Department of Energy National Energy Technology Laboratory Internal Publication, Pittsburgh
Williams TM, Smith B (2000) Hydrochemical characterization of acute acid mine drainage at Iron Duke mine, Mazowe, Zimbabwe. Environ Geol 39(3–4):272–278
Wilson WE, Petrov A (1999) Famous mineral localities: Cerro Rico de Potosí, Bolivia. Mineral Record 30:9–36
World Bank (2009) World Development Report: Reshaping Economic Geography
Younger P (2007) Pro-poor water technologies working both ways: lessons from a two-way, south-north interchange. Geoforum 38:828–840
Younger PL, Banwart SA, Hedin RS (2002) Mine Water: Hydrology, Pollution, Remediation. Kluwer Academic Publishers, Boston
Zartman RE, Cunningham CG (1995) U-Th-Pb zircon dating of the 13.8-Ma dacite volcanic dome at Cerro Rico de Potosí, Bolivia. Earth Planet Sci Lett 133:227–237
Acknowledgments
Elias Puch of the Universidad Autónoma de “Tomás Frías”, Yoichi Matsuda of the Japan International Cooperation Agency, Hugo Arando of the Centro de Investigación Minero Ambiental, and Patrick M. Stack aided greatly in field work and gathering local information key to this manuscript. Engineers Lionel Villarroel Gonzales, Mirko Kirigin, Huascar Beltrán, Franz Mamani, and Primo Choque provided important data, logistical support, materials and contacts, without which this study would have been impossible. Kristina Johnson Strosnider is due thanks for cartographic assistance. A University of Oklahoma Presidential International Travel Fellowship and United States Department of Education Graduate Assistance in Areas of National Need (GAANN) Fellowship partially funded this study.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Strosnider, W.H.J., Llanos López, F.S. & Nairn, R.W. Acid mine drainage at Cerro Rico de Potosí I: unabated high-strength discharges reflect a five century legacy of mining. Environ Earth Sci 64, 899–910 (2011). https://doi.org/10.1007/s12665-011-0996-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12665-011-0996-x