Abstract
The effects of isothermal treatments on the microstructural evolution and coarsening rate of semi-solid 7075 aluminum alloy produced via the recrystallization and partial remelting (RAP) process were investigated. Samples of 7075 aluminum alloy were subjected to cold extrusion, and semi-solid treatment was carried out for 5–30 min at temperatures ranging from 580 to 605°C. A backward-extrusion experiment was conducted to investigate liquid segregation during the thixoforming process. The results revealed that obvious grain coarsening and spheroidization occurred during prolonged isothermal treatments. In addition, higher soaking temperatures promoted the spheroidization and coarsening process because of the increased liquid fraction and the melting of second phases. Segregation of the liquid phase caused by the difference in fluidity between the liquid and the solid phases was observed in different regions of the thixoformed specimens.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
X. Su, G.M. Xu, and J.W. Jiang, Structural and mechanical properties of 7075 alloy strips fabricated by roll-casting in a static magnetic field, Int. J. Miner. Metall. Mater., 21(2014), No. 7, p. 696.
Y.L. Lu, M.Q. Li, X.C. Li, and X.P. Li, Microscopic characterization of semi-solid aluminium alloys, Int. J. Miner. Metall. Mater., 17(2010), No. 3, p. 290.
K.K. Wang, Thixo-forging and simulation of complex parts of aluminum alloy AlSi7Mg, Int. J. Miner. Metall. Mater., 17(2010), No. 1, p. 53.
E.J. Zoqui, J.I. Gracciolli, and L.A. Lourençato, Thixo-formability of the AA6063 alloy: conventional production processes versus electromagnetic stirring, J. Mater. Process Technol., 198(2008), No. 1-3, p. 155.
Y. Birol, Evolution of globular microstructures during processing of aluminium slurries, Trans. Nonferrous Met. Soc. China, 23(2013), No. 1, p. 1.
K.S. Alhawari, M.Z. Omar, M.J. Ghazali, M.S. Salleh, and M.N. Mohammed, Evaluation of the microstructure and dry sliding wear behaviour of thixoformed A319 aluminium alloy, Mater. Des., 76(2015), p. 169.
H.M. Guo, X.J. Yang, and B. Hu, Low superheat pouring with a Shear Field in rheocasting of aluminum alloys, J. Wuhan Univ. Technol. Mater. Sci. Ed., 23(2008), No. 1, p. 54.
A. Bolouri, M. Shahmiri, and E.N.H. Cheshmeh, Microstructural evolution during semisolid state strain induced melt activation process of aluminum 7075 alloy, Trans. Nonferrous Met. Soc. China, 20(2010), No. 9, p. 1663.
A.F. Boostani and S. Tahamtan, Fracture behavior of thixoformed A356 alloy produced by SIMA process, J. Alloys Compd., 481(2009), No. 1-2, p. 220.
A. Haghparast, M. Nourimotlagh, and M. Alipour, Effect of the strain-induced melt activation (SIMA) process on the tensile properties of a new developed super high strength aluminum alloy modified by Al5Ti1B grain refiner, Mater. Charact., 71(2012), p. 6.
A. Bolouri, M. Shahmiri, and C.G. Kang, Study on the effects of the compression ratio and mushy zone heating on the thixotropic microstructure of AA 7075 aluminum alloy via SIMA process, J. Alloys Compd., 509(2011), No. 2, p. 402.
E. Parshizfard and S.G. Shabestari, An investigation on the microstructural evolution and mechanical properties of A380 aluminum alloy during SIMA process, J. Alloys Compd., 509(2011), No. 40, p. 9654.
A. Bolouri and C.G. Kang, Correlation between solid fraction and tensile properties of semisolid RAP processed aluminum alloys, J. Alloys Compd., 516(2012), p. 192.
E.A. Güven, An investigation on the effects of pre-deformation and temperature on thixotropic microstructure of AA2014 aluminum alloy, Trans. Indian Inst. Met., 69(2016), No. 4, p. 935.
C.P. Wang, Y.Y. Zhang, D.F. Li, H.S. Mei, W. Zhang, and J. Liu, Microstructure evolution and mechanical properties of ZK60 magnesium alloy produced by SSTT and RAP route in semi-solid state, Trans. Nonferrous Met. Soc. China, 23(2013), No. 12, p. 3621.
M. Srikanth and A. Sharma, The effect of predeformation and heat treatment on microstructure of Al-7.0% Si-0.45% Mg alloy cast through SIMA route, Trans. Indian Inst. Met., 63(2010), No. 1, p. 11.
M.J. Nayyeri and K. Dehghani, Microstructure evolution in as-cast and SIMA-processed AE42 magnesium alloy, J. Mater. Eng. Perform., 23(2014), No. 9, p. 3077.
C.P. Wang, Z.J. Tang, H.S. Mei, L. Wang, R.Q. Li, and D.F. Li, Formation of spheroidal microstructure in semi-solid state and thixoforming of 7075 high strength aluminum alloy, Rare Met., 34(2015), No. 10. p. 710.
T. Liu, C.N. He, G. Li, X. Meng, C.S. Shi, and N.Q. Zhao, Microstructural evolution in Al–Zn–Mg–Cu–Sc–Zr alloys during short-time homogenization, Int. J. Miner. Metall. Mater., 22(2015), No. 5, p. 516.
H.V. Atkinson and D. Liu, Microstructural coarsening of semi-solid aluminum alloys, Mater. Sci. Eng. A, 496(2008), No. 1-2, p. 439.
A. Bolouri, M. Shahmiri, and C.G. Kang, Coarsening of equiaxed microstructure in the semisolid state of aluminum 7075 alloy through SIMA processing, J. Mater. Sci., 47(2012), No. 8, p. 3544.
G.H. Yan, S.D. Zhao, S.Q. Ma, and H.T. Shou, Microstructural evolution of A356.2 alloy prepared by the SIMA process, Mater. Charact., 69(2012), p. 45.
H. Mohammadi, M. Ketabchi, and A. Kalaki, Microstructure evolution of semi-solid 7075 aluminum alloy during reheating process, J. Mater. Eng. Perform., 20(2011), No. 7, p. 1256.
J.F. Jiang, Y. Wang, and H.V. Atkinson, Microstructural coarsening of 7005 aluminum alloy semisolid billets with high solid fraction, Mater. Charact., 90(2014), p. 52.
H.V. Atkinson and D. Liu, Coarsening rate of microstructure in semi-solid aluminium alloys, Trans. Nonferrous Met. Soc. China, 20(2010), No. 9, p. 1672.
E.D. Manson-Whitton, I.C. Stone, J.R. Jones, P.S. Grant, and B. Cantor, Isothermal grain coarsening of spray formed alloys in the semi-solid state, Acta Mater., 50(2002), No. 10, p. 2517.
H.S. Kim, I.C. Stone, and B. Cantor, Microstructural evolution in semi-solid AA7034, J. Mater. Sci., 43(2008), No. 4, p. 1292.
S. Annavarapu and R.D. Doherty, Inhibited coarsening of solid-liquid microstructures in spray casing at high volume fractions of solid, Acta Metall. Mater., 43(1995), No. 8, p. 3207.
S.C. Hogg and H.V. Atkinson, Inhibited coarsening of a spray-formed and extruded hypereutectic aluminium-silicon alloy in the semi-solid state, Metall. Mater. Trans. A, 36(2005), No. 1, p. 149.
B. Binesh and M. Aghaie-Khafri, RUE-based semi-solid processing: Microstructure evolution and effective parameters, Mater. Des., 95(2016), p. 268.
A. Khosravani, H. Aashuri, P. Davami, A. Narimannezhad, and R. Hadian, Liquid segregation behavior of semi-solid AZ91 alloy during back extrusion test, J. Alloys Compd., 477(2009), No. 1-2, p. 822.
Z.M. Du, G. Chen, Y.S. Cheng, and S.S. Xie, Inhomogeneity of density and mechanical properties of A357 aluminum alloy backward extruded in semi-solid state, Trans. Nonferrous Met. Soc. China, 21(2011), No. 10, p. 2285.
C.G. Kang and K.D., Jung, Improvement of the liquid segregation phenomena of semisolid aluminum alloys by the multistage strain rate control in the compression test, J. Mater. Eng. Perform., 10(2001), No. 4, p. 419.
H.H. Kim, S.M. Lee, and C.G. Kang, Reduction in liquid segregation and microstructure improvement in a semisolid die casting process by varying injection velocity, Metall. Mater. Trans B, 42(2011), No. 1, p. 156.
C.G. Kang and H.K. Jung, A study on solutions for avoiding liquid segregation phenomena in thixoforming process: part II. Net shape manufacturing of automotive scroll component, Metall. Mater. Trans B, 32(2001), No. 1, p. 129.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Fu, Jl., Wang, Kk., Li, Xw. et al. Microstructure evolution and thixoforming behavior of 7075 aluminum alloy in the semi-solid state prepared by RAP method. Int J Miner Metall Mater 23, 1404–1415 (2016). https://doi.org/10.1007/s12613-016-1364-3
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12613-016-1364-3