Abstract
The effect of electroslag remelting (ESR) on carbides in 8Cr13MoV martensitic stainless steel was experimentally studied. Phases precipitated from liquid steel during solidification were calculated using the Thermo-Calc software. The carbon segregation was analyzed by original position analysis (OPA), and the carbides were analyzed by optical microscopy (OM), scanning electron microscopy (SEM), energy- dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD). The results indicated that more uniform carbon distribution and less segregation were obtained in the case of samples subjected to the ESR process. After ESR, the amount of netty carbides decreased significantly, and the chromium and vanadium contents in the grain-boundary carbides was reduced. The total area and average size of carbides were obviously smaller after the ESR process. In the sample subjected to ESR, the morphology of carbides changed from lamellar and angular to globular or lump, whereas the types of carbides did not change; both M23C6 and M7C3 were present before and after the ESR process.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
M.Q. Chen, B.K. Li, and L. Zhao, The cellular automata model of electroslag remelting ingot structure, J. Mater. Metall., 10(2011), p. 130.
Z.B. Li, Electroslag Metallurgy Theory and Practice, Metallurgical Industry Press, Beijing, 2010, p. 66.
Z.F. Ni, Y.S. Sun, F. Xue, J. Zhou, and J. Bai, Evaluation of electroslag remelting in TiC particle reinforced 304 stainless steel, Mater. Sci. Eng. A, 528(2011), No. 11, p. 5664.
Q.L. Wu, Y.S. Sun, F. Xue, and J. Zhou, Microstructure, mechanical and wear properties of TiC particulate reinforced 2Cr13 steel by in situ reaction and electroslag remelting, Ironmaking Steelmaking, 35(2008), No. 5, p. 387.
Y.W. Dong, Z.H. Jiang, and Z.B. Li, Segregation of niobium during electroslag remelting process, J. Iron Steel Res. Int., 16(2009), No. 1, p. 7.
H. Halfa, Characterization of electroslag remelted super hard high speed tool steel containing niobium, Steel Res. Int., 84(2013), No. 5, p. 495.
J.Y. Park and Y.S. Park, The effects of heat-treatment parameters on corrosion resistance and phase transformations of 14Cr–3Mo martensitic stainless steel, Mater. Sci. Eng. A, 449–451(2007), p. 1131.
J.W. Lee and J.T. Kim, The effect of Co-N addition on mechanical properties, microstructure and erosion of 17Cr steels, ISI J Int., 48(2008), No. 1, p. 114.
A. Bhattacharya and P.M. Singh, Effect of heat treatment on corrosion and stress corrosion cracking of S32205 duplex stainless steel in caustic solution, Metall. Mater. Trans. A, 40(2009), No. 6, p. 1388.
K.H. Kim, S.D. Park, and C.M. Bae, New approach to the soaking condition of 100Cr6 high-carbon chromium bearing steel, Met. Mater. Int., 20(2014), No. 2, p. 207.
J.M. Xiao, Metallography Issue of Stainless Steel, Metallurgical Industry Press, Beijing, 2006, p. 41.
H.J. Wu, N. Wei, Y.P. Bao, G.X. Wang, C.P. Xiao, and J.J. Liu, Effect of M-EMS on the solidification structure of a steel billet, Int. J. Miner. Metall. Mater., 18(2011), No. 2, p. 159.
Q.Y. Zhang, L.T. Wang, and X.H. Wang, Influence of casting speed variation during unsteady continuous casting on non-metallic inclusions in if steel slabs, ISIJ Int., 46(2006), No. 10, p. 1421.
Y.R. Liu, D. Ye, Q.L. Yong, J. Su, K.Y. Zhao, and W. Jiang, Effect of heat treatment on microstructure and property of Cr13 super martensitic stainless steel, J. Iron Steel Res. Int., 18(2011), No. 11, p. 60.
Z.L. Song, X.D. Du, Y.Q. Chen, J.Q. Wang, C. Ye, and L.Y. Li, Microstructure and impact toughness of 7Cr17Mo martensitic stainless steel, Trans. Mater. Heat Treat., 32(2011), No. 5, p. 95.
J.Y. Li, P. Zhao, J. Yanagimoto, S. Sugiyama, and Y.L. Chen, Effects of heat treatment on the microstructures and mechanical properties of a new type of nitrogen-containing die steel, Int. J. Miner. Metall. Mater., 19(2012), No. 6, p. 511.
L.D. Barlow and M. Du. Toit, Effect of austenitizing heat treatment on the microstructure and hardness of martensitic stainless steel AISI 420, J. Mater. Eng. Perform., 21(2012), No. 7, p. 1327.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zhu, Qt., Li, J., Shi, Cb. et al. Effect of electroslag remelting on carbides in 8Cr13MoV martensitic stainless steel. Int J Miner Metall Mater 22, 1149–1156 (2015). https://doi.org/10.1007/s12613-015-1179-7
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12613-015-1179-7