Abstract
Real-time thermal error compensation of machine tool feed drive in general can be separated into three steps such as modeling, measurement and compensation. In the previous report, as the parts of the thermal error compensation system, component heat generation, compensation method, thermal model, mathematic model and calculation method were studied respectively. And a series of simulations was carried out in several kinds of working condition. And then, in order to discuss the correctness of the developed ball screw thermal error compensation system, a series of tests contains axial deformation, positioning accuracy, temperature variation and temperature distribution was carried out in the same working condition of prediction. As the results, the test data well confirmed the correctness of the developed ball screw thermal error compensation system.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Ramesh, R., Mannan, M., and Poo, A., “Thermal Error Measurement and Modelling in Machine Tools.: Part I. Influence of Varying Operating Conditions,” International Journal of Machine Tools and Manufacture, Vol. 43, No. 4, pp. 391–404, 2003.
Ramesh, R., Mannan, M., Poo, A., and Keerthi, S., “Thermal Error Measurement and Modelling in Machine Tools. Part II. Hybrid Bayesian Network-Support Vector Machine Model,” International Journal of Machine Tools and Manufacture, Vol. 43, No. 4, pp. 405–419, 2003.
Ramesh, R., Mannan, M., and Poo, A., “Error Compensation in Machine Tools-A Review: Part I: Geometric, Cutting-Force Induced and Fixture-Dependent Errors,” International Journal of Machine Tools and Manufacture, Vol. 40, No. 9, pp. 1235–1256, 2000.
Ramesh, R., Mannan, M., and Poo, A., “Error Compensation in Machine Tools-A Review: Part II: Thermal Errors,” International Journal of Machine Tools and Manufacture, Vol. 40, No. 9, pp. 1257–1284, 2000.
Xu, Z. Z., Liu, X. J., Kim, H. K., Shin, J. H., and Lyu, S. K., “Thermal Error Forecast and Performance Evaluation for an Air-Cooling Ball Screw System,” International Journal of Machine Tools and Manufacture, Vol. 51, No. 7, pp. 605–611, 2011.
Xu, Z.-Z., Liu, X.-J., and Lyu, S.-K., “Study on Positioning Accuracy of Nut/Shaft Air Cooling Ball Screw for High-Precision Feed Drive,” Int. J. Precis. Eng. Manuf., Vol. 15, No. 1, pp. 111–116, 2014.
Xu, Z.-Z., Liu, X.-J., and Lyu, S.-K., “Study on Thermal Behavior Analysis of Nut/Shaft Air Cooling Ball Screw for High-Precision Feed Drive,” Int. J. Precis. Eng. Manuf., Vol. 15, No. 1, pp. 123–128, 2014.
Wei, J., Lv, C., Sun, W., Li, X., and Wang, Y., “A Study on Optimum Design Method of Gear Transmission System for Wind Turbine,” Int. J. Precis. Eng. Manuf., Vol. 14, No. 5, pp. 767–778, 2013.
Wei, J., Sun, Q., Sun, X., and Sun, W., “A Study on Rotor Profiles Design for a Novel Twin-Screw Kneader,” Int. J. Precis. Eng. Manuf., Vol. 14, No. 3, pp. 451–459, 2013.
Wei, J., Liang, X. L., Chen, D. B., Yang, Y. L., and Zhou, D. M., “Evaluation of the Mixing Performance for One Novel Twin Screw Kneader with Particle Tracking,” Polymer Engineering & Science, Vol. 54, No. 10, pp. 2407–2419, 2014.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Xu, ZZ., Choi, C., Liang, Lj. et al. Study on a novel thermal error compensation system for high-precision ball screw feed drive (2nd report: Experimental verification). Int. J. Precis. Eng. Manuf. 16, 2139–2145 (2015). https://doi.org/10.1007/s12541-015-0276-x
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-015-0276-x