Abstract
The Preston's equation which was known as the governing equation of the polishing results in CMP process is caused by the wafer pressure and velocity. It is very important for the pressure and velocity to examine the fundamental characteristics which have effects on the polishing results. In this study, the intelligent pad which can measure the pressure distribution delivered to the wafer by the independent change of the pressure and velocity in real-time was used. The intelligent pad has sheet shape of embedded pressure sensor and functions of pressure signal processing, saving and transmitting in real-time. The average and the deviation of pressure signals were calculated by extracting the signal value from the measured pressure distribution, and the quantitative analysis was conducted by using the full width at half maximum (FWHM) value of the probability density function. The suitability of pressure signal was confirmed by polishing the oxide wafer in the same experiment conditions. So, the average and deviation of the pressure signal value correspond with the material removal rate (MRR) and non-uniformity of the polishing result. In conclusion, the intelligent pad system will be a good monitoring tool to understand various phenomena in CMP process.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Lee, H., “Empirical Modeling of Wafer-Scale Removal Profile using Spatial Parameter in Copper CMP,” Ph.D. Thesis, Graduate School of Mechanical Engineering, Pusan National University, 2010.
Kim, H., “A Study on the Interfacial Characteristics and Its Effect on Material Removal in CMP,” Ph.D. Thesis, Graduate School of Mechanical Engineering, Pusan National University, 2003.
Preston, F. W., “The Theory and Design of Plate Glass Polishing Machines,” Journal of the Society of Glass Technology, Vol. 11, No. 44, pp. 214–256, 1927.
Jeong, H., Park, B., Lee, H., Kim, H., Seo, H., et al., “Monitoring System in CMP Process,” Proc. of the 1st Pac-Rim International Conference on Planarization CMP and Its Application Technology, pp. 54–65, 2004.
Li, Y., “Microelectronic Applications of Chemical Mechanical Planarization,” John Wiley & Sons, pp. 94–95, 2008.
Kim, H. J., Kim, H. Y., Jeong, H. D., Lee, E. S., and Shin, Y. J., “Friction and Thermal Phenomena in Chemical Mechanical Polishing,” Journal of Materials Processing Technology, Vols. 130–131, pp. 334–338, 2002.
Sorooshian, J., Hetherington, D., and Philipossian, A., “Effect of Process Temperature on Coefficient of Friction during CMP,” Electrochemical and Solid-State Letters, Vol. 7, No. 10, pp. G222–G224, 2004.
Hocheng, H., Huang, Y. L., and Chen, L. J., “Kinematic Analysis and Measurement of Temperature Rise on a Pad in Chemical Mechanical Planarization,” Journal of the Electrochemical Society, Vol. 146, No. 11, pp. 4236–4239, 1999.
Wikipedia, “Full Width at Half Maximum,” http://en.wikipedia.org/wiki/Full_width_at_half_maximum (Accessed 15 APR 2015)
Yu, T. K., Yu, C., and Orlowski, M., “Combined Asperity Contact and Fluid Flow Model for Chemical-Mechanical Polishing,” Proc. of IEEE International Workshop on Numerical Modeling of Processes and Devices for Integrated Circuits, pp. 29–32, 1994.
Lu, J., Rogers, C., Manno, V., Philipossian, A., Anjur, S., and Moinpour, M., “Measurements of Slurry Film Thickness and Wafer Drag during CMP,” Journal of the Electrochemical Society, Vol. 151, No. 4, pp. G241–G247, 2004.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Lee, C., Park, J., Kinoshita, M. et al. Analysis of pressure distribution and verification of pressure signal by changes load and velocity in chemical mechanical polishing. Int. J. Precis. Eng. Manuf. 16, 1061–1066 (2015). https://doi.org/10.1007/s12541-015-0137-7
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-015-0137-7