Abstract
This paper focuses on tip shape and degradation of diamond indenters upon high temperature nanoindentation tests. Accurate indenter area functions (IAFs) are essential for the correct measurement of mechanical properties by instrumented indentation techniques (IIT), particularly during high temperature (HT) nanoindentation. However, being a relatively new technique, sufficient information is lacking. This paper examines the shape and degradation of a Berkovich indenter tip after HT nanoindentation testing of 1 mm-thick SiC and Al thin films at room temperature and at T=100°C, 200°C and 300°C. IAFs were determined by the reference method and by atomic force microscopy (AFM), with the latter giving higher contact areas, although tip defect values extracted from both methods were in good agreement. Examination of the tip by AFM after HT nanoindentation on SiC reveals a blunt tip and the need for a new IAF. The work emphasizes the importance of carrying out indenter tip shape calibrations on a regular basis, especially when indenting and scanning hard samples and metals that readily oxidise at T>200°C, where the tip gets easily contaminated.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Wood, A. J. and Clyne, T. W., “Measurement and Modelling of the Nanoindentation Response of Shape Memory Alloys,” Acta Materialia, Vol. 54, No. 20, pp. 5607–5615, 2006.
Chen, J., Beake, B. D., Dong, H., and Bell, G. A., “Environmental Nanomechanical Testing of Polymers and Nanocomposites,” Nanomechanical Analysis of High Performance Materials, pp.63–84, 2014.
Lucca, D. A., Hermann, K., and Klopfstein, M. J., “Nanoindentation: Measuring Methods and Applications,” CIRP Annals- Manufacturing Technology, Vol. 59, No. 2, pp. 803–819, 2010.
Oliver, W. C. and Pharr, G. M., “Measurement of Hardness and Elastic Modulus by Instrumented Indentation: Advances in Understanding and Refinements to Methodology,” Journal of Materials Research, Vol. 19, No. 1, pp. 3–20, 2004.
Lund, A. C., Hodge, A. M., and Schuh, C. A., “Incipient Plasticity during Nanoindentation at Elevated Temperatures,” Applied Physics Letters, Vol. 85, No. 8, pp. 1362–1364, 2004.
Rajulapati, K., Biener, M., Biener, J., and Hodge, A., “Temperature Dependence of the Plastic Flow Behavior of Tantalum,” Philosophical Magazine Letters, Vol. 90, No. 1, pp. 35–42, 2010.
Franke, O., Trenkle, J. C., and Schuh, C. A., “Temperature Dependence of the Indentation Size Effect,” Journal of Materials Research, Vol. 25, No. 7, pp. 1225–1229, 2010.
Soler, R., Molina-Aldareguia, J. M., Segurado, J., and LLorca, J., “Effect of Misorientation on the Compression of Highly Anisotropic Single-Crystal Micropillars,” Advanced Engineering Materials, Vol. 14, No. 11, pp. 1004–1008, 2012.
Monclus, M. A., Zheng, S. J., Mayeur, J. R., Beyerlein, I. J., Mara, N. A., et al., “Optimum High Temperature Strength of Two-Dimensional Nanocomposites,” APL Materials, Vol. 1, No. 5, Paper No. 052103, 2013.
Lotfian, S., Rodriguez, M., Yazzie, K., Chawla, N., Llorca, J., and Molina-Aldareguia, J., “High Temperature Micropillar Compression of Al/SiC Nanolaminates,” Acta Materialia, Vol. 61, No. 12, pp. 4439–4451, 2013.
Ruffell, S., Bradby, J. E., Williams, J. S., Munoz-Paniagua, D., Tadayyon, S., et al., “Nanoindentation-Induced Phase Transformations in Silicon at Elevated Temperatures,” Nanotechnology, Vol. 20, No. 13, Paper No. 135603, 2009.
Wheeler, J. M. and Michler, J., “Indenter Materials for High Temperature Nanoindentation,” Review of Scientific Instruments, Vol. 84, No. 10, Paper No. 101301, 2013.
Oliver, W. C. and Pharr, G. M., “An Improved Technique for Determining Hardness and Elastic Modulus using Load and Displacement Sensing Indentation Experiments,” Journal of Materials Research, Vol. 7, No. 6, pp. 1564–1583, 1992.
Schuh, C. A., Packard, C. E., and Lund, A. C., “Nanoindentation and Contact-Mode Imaging at High Temperatures,” Journal of Materials Research, Vol. 21, No. 3, pp. 725–736, 2006.
Choi, J. H. and Korach, C. S., “Tip Bluntness Transition Measured with Atomic Force Microscopy and the Effect on Hardness Variation with Depth In Silicon Dioxide Nanoindentation,” Int. J. Precis. Eng. Manuf., Vol. 12, No. 2, pp. 345–354, 2011.
Fischer-Cripps A. C., “Nanoindentation,” Springer, pp. 86–87, 2011.
Krier, J., Breuils, J., Jacomine, L., and Pelletier, H., “Introduction of the Real Tip Defect of Berkovich Indenter to Reproduce with FEM Nanoindentation Test at Shallow Penetration Depth,” Journal of Materials Research, Vol. 27, No. 1, pp. 28–38, 2012.
Bull, S., “Nanoindentation of Coatings,” Journal of Physics D: Applied Physics, Vol. 38, No. 24, pp. R393–R413, 2005.
Wheeler, J., Oliver, R., and Clyne, T., “AFM Observation of Diamond Indenters after Oxidation at Elevated Temperatures,” Diamond and Related Materials, Vol. 19, No. 11, pp. 1348–1353, 2010.
Snead, L. L., Nozawa, T., Katoh, Y., Byun, T. S., Kondo, S., and Petti, D. A., “Handbook of SiC Properties for Fuel Performance Modeling,” Journal of Nuclear Materials, Vol. 371, No. 1, pp. 329–377, 2007.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Monclús, M.A., Lotfian, S. & Molina-Aldareguía, J.M. Tip shape effect on hot nanoindentation hardness and modulus measurements. Int. J. Precis. Eng. Manuf. 15, 1513–1519 (2014). https://doi.org/10.1007/s12541-014-0499-2
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-014-0499-2