Abstract
The drag reduction of a pickup truck by a rear flap add-on was examined through CFD simulations and wind tunnel experiments. When installed at the rear edge of the roof, the flap increased the cabin back surface pressure coefficient, causing the downwash of the bed flow to be inclined on the tailgate. Thus, the attachment of the bed flow to the tailgate was eliminated; consequently, the drag coefficient was reduced with increasing flap length and downward angle despite the enlarged reverse flow in the wake. However, the drag coefficient did not decrease any further after a specific downward angle was reached because the bed flow increased the drag force at the tailgate and the flap lowered the pressure field above the flap. To maximize the drag reduction effect, the rear downward flap should be designed to have an optimum downward angle.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Abbreviations
- C D :
-
drag coefficient
- C P :
-
pressure coefficient
- H :
-
cabin back height
- L :
-
vehicle length
- Re :
-
Reynolds number
- U ∞ :
-
freestream velocity
- X, Y, Z :
-
wind tunnel coordinates
- l :
-
flap length
- θ :
-
downward angle
References
Al-Garni, A. M., Bernal, L. P. and Khalighi, B. (2003). Experimental investigation of the near wake of a pick-up truck. SAE Paper No. 2003-01-0651.
Cooper, K. R. (2004). Pickup truck aerodynamics - keep your tailgate up. SAE Paper No. 2004-01-1146.
Ha, J., Jeong, S. and Obayashi, S. (2010). Flow characteristics of a pickup truck with regard to the bed geometry variation. Proc. Inst. Mech. Eng. D, J. Automobile Engineering, 224, 881–891.
Holloway, S., Leylek, J. H., York, W. D. and Khalighi, B. (2009). Aerodynamics of a pickup truck: Combined CFD and experimental study. SAE Int. J. Commercial Vehicles, 2, 88–100.
Jeff, H. (2002). Aerodynamic drag of a compact SUV as measured on-road and in the wind tunnel. SAE Paper No. 2002-01-0529.
Khalighi, B., Zhang, S., Koromilas, C., Balkanyi, S. R., Bernal, L. P., Laccarino, G. and Moin, P. (2001). Experimental and computational study of unsteady wake flow behind a bluff body with a drag reduction device. SAE Paper No. 2001-01-1042.
Kim, M. (2005). Aerodynamic simulation on the drag reduction device of a large-sized bus model. Int. J. Heavy Vehicle Systems, 12, 207–224.
Kim, C. H. and Youn, C. B. (2005). Aerodynamic effect of roof-fairing system on a heavy-duty truck. Int. J. Automotive Technology 6,3, 221–227.
Lokhande, B., Sovani, S. and Khalighi, B. (2003). Transient simulation of the flow field around a generic pickup truck. SAE Paper No. 2003-01-1313.
Menter, F. R. (1994). Two-equation eddy-viscosity turbulence models for engineering applications. AIAA J., 32, 1588–1605.
Mokhtar, W. A., Britcher, C. P. and Camp, R. E. (2009). Further analysis of pickup trucks aerodynamics. SAE Paper No. 2009-01-1161.
Ortega, J. M. and Salari, K. (2004). An experimental study of drag reduction devices for a trailer underbody and base. Proc. 34th AIAA Fluid Dynamics Conf. and Exhibit, AIAA-2004-2252.
Yang, Z. and Khalighi, B. (2005). CFD simulations for flow over pickup trucks. SAE Paper No. 2005-01-0547.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Ha, J., Jeong, S. & Obayashi, S. Drag reduction of a pickup truck by a rear downward flap. Int.J Automot. Technol. 12, 369–374 (2011). https://doi.org/10.1007/s12239-011-0043-7
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12239-011-0043-7