Abstract
This paper explains the effect of turning parameters such as cutting speed, feed rate, depth of cut and cutting tool nose radius on surface roughness of hybrid metal matrix (Al-SiCp-Fly ash) composite. Experiments have been conducted based on the orthogonal array L16(4)5 and surface roughness was tested on the composites turned by an high speed CNC centre lathe. Analysis of variance (ANOVA) was performed to predict the significant parameters and their contribution towards surface finish of the composite. A mathematical model was developed using non-linear regression analysis. Taguchi method and Genetic algorithm have been employed to optimize the turning parameters for optimum surface roughness of the composite. The optimum turning parametric conditions have been checked with the confirmation experiments. It has been noted that the optimum condition of genetic algorithm exhibited better results than the experimental results based on the orthogonal array and the optimum condition of Taguchi method.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
M. P. K. Suragimath and G. K. Purohit, A study on mechanical properties of aluminium alloy (LM6) reinforced with SiC and fly ash, IOSR J.Mechanical and Civil Engg., 8 (2013) 13–18.
A. Pramanik, L. C. Zhang and J. A. Arsecularatne, Machining of metal matrix composites: effect of ceramic particles on residual stress, surface roughness and chip formation, Int. J. Machine Tools and Manufacture, 48 (2008)1613–1625.
A. Srinivasan, R. M. Arunachalam, S. Ramesh and J. S. Senthilkumaar, Machining performance study on metal matrix composites-a response surface methodology approach, American Journal of Applied Sciences, 9 (2012) 478–483.
P. Sahoo, Optimization of turning parameters for surface roughness using RSM and GA, APEN Journal (2011) 197–208.
P. V. S. Suresh, P. V. Rao and S. G. Deshmukh, A genetic algorithmic approach for optimization of surface roughness prediction model, Int. J. Machine Tools and Manufacture, 42 (2002) 675–680.
B. Admile, S. G. Kulkarni and S. A. Sonawane, Review on mechanical and wear behavior of aluminum-fly ash metal matrix composite, Int. J. Emerging Technology and advanced Engineering, 4 (2014) 863–866.
M. Sureshkumar, M. M. Priya, C. SathishKumar and V. Baskaran, Surface roughness optimization of metal matrix composite using Taguchi technique, Int. J. Engineering Research and Technology, 2 (2013) 1–6.
P. Senthil and K. S. Amirthagadeswaran, Enhancing wear resistance of squeeze cast AC2A aluminum alloy, Int. Journal of Engineering-Transactions A, 26 (2012) 365.
P. Senthil and K. S. Amirthagadeswaran, Optimization of squeeze casting parameters for non symmetrical AC2A aluminium alloy castings through Taguchi method, J. Mechanical Science and Technology, 26 (2012) 1141–1147.
P. Senthil and K. S. Amirthagadeswaran, Experimental study and squeeze casting process optimization for high quality AC2A aluminium alloy castings, Arabian Journal for Science and Engineering, 39 (2014) 2215–2225.
K. K. Alaneme, B. O. Ademilua and M. O. Bodunrin, Mechanical properties and corrosion behaviour of aluminium hybrid composites reinforced with silicon carbide and bamboo leaf ash, Tribology in Industry, 35 (2013) 25–35.
T. Ozel and Y. Karpat, Predictive modeling of surface roughness and tool wear in hard turning using regression and neural networks, Int. J. Machine Tools and Manufacture, 45 (2005) 467–479.
B. S. Reddy, G. Padmanabhan and K. V. K. Reddy, Surface roughness prediction techniques for CNC turning, Asian Journal of Scientific Research, 1 (2008) 256–264.
J. Singh and A. Chauhan, Overview of aluminium matrix composites for automotive applications, Int. J. Applied Engineering Research, 9 (2014) 959–966.
S. Charles and V. P. Arunachalam, Property analysis and mathematical modeling of machining properties of aluminium alloy hybrid (Al-alloy/SiC/flyash) composites produced by liquid metallurgy and powder metallurgy techniques, Indian J. Engineering and Material Science, 11 (2004) 473–480.
P. K. Jayashree, G. Shankar, A. U. Kini, S. S. Sharma and R. Shetty, Review on effect of silicon carbide (SiC) on stir cast aluminium metal matrix composites, Int. J. Current Engineering and Technology, 3 (2013) 1061–1071.
L. B. Abhang and M. Hameedullah, Modeling and analysis for surface roughness in machining EN-31 steel using response surface methodology, Int. J. Applied Research in Mechanical Engineering, 1 (2011) 33–38.
C. R. Barik and N. K. Mandel, Parametric effect and optimization of surface roughness of EN 31 in CNC dry turning, Int. J. Lean Thinking, 3 (2010) 1–13.
S. G. Ahmed, Development of a prediction model for surface roughness in finish turning of aluminium, Sudan Engineering Society Journal, 52 (2006) 1–5.
C. X. Feng and X. Wang, Development of empirical models for surface roughness prediction in finish turning, Int. J. Advanced Manufacturing Technology, 20 (2002) 348–356.
R. Pai, V. Kamath and S. S. Rao, Study on surface roughness minimization in turning of DRACs using surface roughness methodology and Taguchi under pressured steam jet approach, ARPN J. Engineering and Applied Sciences, 3 (2008) 59–67.
A. R. Ravikumar, K. S. Amirthagadeswaran and P. Senthil, Parametric optimization of squeeze cast AC2A-Ni coated composite using Taguchi technique, Advances in Materials Science and Engineering, 14 (2014) 1–10.
J. J. Rino, D. Chandramohan, K. S. Sucitharan and V. D. Jebin, An overview on development of aluminium metal matrix composites with hybrid reinforcement, Int. J. Science and Research, 1 (2012) 196–203.
R. Behera, S. Das, D. Chatterjee and G. Sutradhar, Forgeability and machinability of stir cast aluminum alloy metal matrix composites, J. Minerals and Materials Characterization and Engineering, 10 (2011) 923–939.
R. Behera and G. Sutradhar, Machinability of LM6/SiCp metal matrix composites with tungsten carbide cutting tool inserts, ARPN J. Engineering and Applied Sciences, 7 (2012) 216–221.
H. C. Anilkumar, H. S. Hebbar and K. S. Ravishankar, Mechanical properties of fly ash reinforced aluminium alloy (Al6061) composites, Int. J. Mechanical and Materials Engineering, 6 (2011) 41–45.
K. Shunmugesh, K. Panneerselvam and M. Pramod, Optimization of CNC turning parameters with carbide tool for surface roughness analysis using Taguchi analysis, Research Journal of Engineering Science, 3 (2014) 1–7.
D. P. Selvaraj and P. Chandramohan, Optimization of surface roughness of AISI 304 austenitic stainless steel in dry turning operation using Taguchi design method, J. Engg. Science and Technology, 5 (2010) 293–301.
R. A. Mahdavinejad and H. S. Bidgoli, Optimization of surface roughness parameters in dry turning, J. Achievements in Materials and Manufacturing Engineering, 37 (2009) 571–577.
H. M. Somashekara and N. L. Swamy, Optimizing surface roughness in turning operation using Taguchi technique and ANOVA, Int. J. Engineering Science and Technology, 4 (2012) 1967–1973.
M. A. Baghchesara and H. Abdizadeh, Microstructural and mechanical properties of nanometric magnesium oxide particulate-reinforced aluminum matrix composites produced by powder metallurgy method, J. Mechanical Science and Technology, 26 (2012) 367–372.
B. C. Goo and M. H. Kim, Characteristics of A356/SiCp and A390/SiCp composites, J. Mechanical Science and Technology, 26 (2012) 2097–2100.
W. Lee, H. Hwang, H. Kim, C. Park, S. Huh and W. Park, The characteristics of intermetallic compounds and hardness of Ni-Cr/AC8A composites under different infiltration temperatures, J. Mechanical Science and Technology, 26 (2012) 2627–2630.
Author information
Authors and Affiliations
Corresponding author
Additional information
E. Baburaj is currently a Professor at the Department of Mechanical Engineering, Karpagam College of Engineering, Coimbatore, India. He has several publications in different journals and conferences. His current research interests include Stir Casting, Non-ferrous Composites, Optimization Techniques and Composites Machining.
K. M. Mohana Sundaram is a Principal, Jansons Institute of Technology, Coimbatore, India. His publications are over 50 in different journals and conferences. His current research interests include Simulation of Manufacturing systems, Scheduling, Cellular Manufacturing Systems, Non-traditional Optimization Algorithms, Robotics, Squeeze Casting and Electro Discharge Machining.
P. Senthil is currently a Professor at the Department of Mechanical Engineering, Karpagam University, Coimbatore, India. His publications are over 20 in different journals and conferences. His current research interests include Squeeze Casting, Non-ferrous their Composites, Non-traditional Optimization Algorithms, Robotics and Composites Machining.
Rights and permissions
About this article
Cite this article
Baburaj, E., Mohana Sundaram, K.M. & Senthil, P. Effect of high speed turning operation on surface roughness of hybrid metal matrix (Al-SiCp-fly ash) composite. J Mech Sci Technol 30, 89–95 (2016). https://doi.org/10.1007/s12206-015-1210-y
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12206-015-1210-y