Abstract
Soil stabilisation is one type of ground improvement technique regarded as effective in minimising foundation problems associated with marine clay (MC). In this paper, in-depth micro-level analysis was conducted on MC stabilised with 8% Polyurethane (PU). The effectiveness of PU as a stabiliser was evaluated using unconfined compressive strength (UCS) tests and one-dimensional consolidation tests. Mineralogy of MC was studied using X-ray diffraction analysis (XRD). Furthermore, field emission scanning electron microscopy (FESEM) and energy dispersive spectroscopy (EDX) were used to discern the roots of improvement in the strength of MC. The result of XRD analysis identified the presence of Quartz, Montmorillonite, Calcite and Clinochlore. FESEM results discovered that MC showed crumpled, curled and flaked soil particles that have a fuzzy arrangement and cusp-like crystals in a joined fashion. The contact among the particles is surface-to-surface and surface-to-edge. The PU foam was composed of intramolecular closed cells that are non-homogeneous, non-identical, and of inconsistent average diameters of about 2.3 µm. Finally, EDX results revealed that O, C, Si, Al, Fe and N are the elements that contributed more than 96% of the composition of MC and PU.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Abbreviations
- ASTM:
-
American Society for Testing and Materials
- Cc :
-
Compression index
- Cr :
-
Swelling index
- EDX:
-
Energy Dispersive Spectroscopy
- FESEM:
-
Field Emission Scanning Electron Microscopy
- JCPDS:
-
Joint Committee on Powder Diffraction Standards
- MC:
-
Marine Clay
- MDD:
-
Maximum Dry Density
- OMC:
-
Optimum Moisture Content
- PU:
-
Polyurethane
- UCS:
-
Unconfined Compressive Strength
- XRD:
-
X-Ray Diffraction analysis
References
Ahmari S, Zhang L (2013) Utilization of cement kiln dust (CKD) to enhance mine tailings-based geopolymer bricks. Construction and Building Materials 40:1002–1011, DOI: https://doi.org/10.1016/j.conbuildmat.2012.11.069
ASTM (2017) Standard practice for making and curing soil-cement compression and flexure test specimens in the laboratory. D1632-17, American Society for Testing and Materials, West Conshohocken, PA, USA
Babcock BN (2018) Cement grout vs chemical grout: Which one to use, when, and why. A white paper providing guidance to the geotechnical community, Avanti International, Houston, TX, USA
Bayati M, Khademi Hamidi J (2017) A case study on TBM tunnelling in fault zones and lessons learned from ground improvement. Tunnelling and Underground Space Technology 63:162–170, DOI: https://doi.org/10.1016/j.tust.2016.12.006
Bensaifi E, Bouteldja F, Nouaouria MS, Breul P (2019) Influence of crushed granulated blast furnace slag and calcined eggshell waste on mechanical properties of a compacted marl. Transportation Geotechnics 20:100244, DOI: https://doi.org/10.1016/j.trgeo.2019.100244
BS1377-5 (1990) Compressibility, permeability and durability tests. BS1377–5, British Standard Institution, London, UK
Cai G, Liu S (2017) Compaction and mechanical characteristics and stabilization mechanism of carbonated reactive MgO-stabilized silt. KSCE Journal of Civil Engineering 21(11):2641–2654, DOI: https://doi.org/10.1007/s12205-017-1145-1
Chun B, Ryu DS, Shin C, Im G, Choi J, Lim H (1997) The performance of polyurethane injection method with soil nailing system for ground reinforcement. Ground Improvement Geosystems, 445–451
Estabragh AR, Afsari E, Javadi AA, Babalar M (2020) Effect of Two organic chemical fluids on the mechanical properties of an expansive clay soil. Journal of Testing and Evaluation 48(5):20170623, DOI: https://doi.org/10.1520/JTE20170623
Guo L, Wu DQ (2017) Study of recycling Singapore solid waste as land reclamation filling material. Sustainable Environment Research 27(1):1–6, DOI: https://doi.org/10.1016/j.serj.2016.10.003
Guo L, Wu DQ (2018) Study of leaching scenarios for the application of incineration bottom ash and marine clay for land reclamation. Sustainable Environment Research 28(6):396–402, DOI: https://doi.org/10.1016/j.serj.2018.06.004
Gunturi M, Ravichandran PT, K DK, Annadurai R, Rajkumar PRK (2015) Micro level analysis of RBI 81 stabilized expansive soil. International Journal of ChemTech Research 7(2):666–672
He Z, Li Q, Wang J, Yin N, Jiang S, Kang M (2016) Effect of silane treatment on the mechanical properties of polyurethane/water glass grouting materials. Construction and Building Materials 116:110–120, DOI: https://doi.org/10.1016/j.conbuildmat.2016.04.112
Hemalatha MS, Santhanam M (2018) Characterizing supplementary cementing materials in blended mortars. Construction and Building Materials 191:440–459, DOI: https://doi.org/10.1016/j.conbuildmat.2018.09.208
Ivanov V, Chu J, Stabnikov V, Li B (2015) Strengthening of soft marine clay using bioencapsulation. Marine Georesources & Geotechnology 33(4):320–324, DOI: https://doi.org/10.1080/1064119X.2013.877107
Jamaludin N, Mohd Yunus NZ, Jusoh SN, Pakir F, Ayub A, Zainuddin NE, Hezmi MA, Mashros N (2019) Potential and future: Utilization of waste material on strength characteristics of marine clay. IOP Conference Series: Materials Science and Engineering 527:012003, DOI: https://doi.org/10.1088/1757-899X/527/1/012003
JCPDS (1995) Standard X-ray diffraction powder patterns. International centre for diffraction data, US Department of Commerce, Washington, DC, USA
Kazemian S, Huat BBK, Prasad A, Barghchi M (2010) A review of stabilization of soft soils by injection of chemical grouting. Australian Journal of Basic and Applied Sciences 6(12):5862–5868
Kundu SP, Chakraborty S, Chakraborty S (2018) Effectiveness of the surface modified jute fibre as fibre reinforcement in controlling the physical and mechanical properties of concrete paver blocks. Construction and Building Materials 191:554–563, DOI: https://doi.org/10.1016/j.conbuildmat.2018.10.045
Lei H, Feng S, Jiang Y (2018) Geotechnical characteristics and consolidation properties of Tianjin marine clay. Geomechanics and Engineering 16(2):125–140, DOI: https://doi.org/10.12989/gae.2018.16.2.125
Li S, Liu R, Zhang Q, Zhang X (2016) Protection against water or mud inrush in tunnels by grouting: A review. Journal of Rock Mechanics and Geotechnical Engineering 8(5):753–766, DOI: https://doi.org/10.1016/j.jrmge.2016.05.002
Ling FNL, Kassim KA, Karim ATA, Ho SC (2014) Evaluation of contributing factors on strength development of lime stabilized artificial organic soils using statistical design of experiment approach. Advanced Materials Research 905:362–368, DOI: https://doi.org/10.4028/www.scientific.net/AMR.905.362
MEEI (2014) Energy dispersive x-ray spectroscopy — handbook of analytical methods for materials. Materials Evaluation and Engineering, Inc., Plymouth, MN, USA, 17–18
Mohd Yunus NZ, Marto A, Pakir F, Kasran K, Jamal MAA, Jusoh SN, Abdullah N (2015) Performance of lime-treated marine clay on strength and compressibility chracteristics. International Journal of Geomate 8(2):1232–1238, DOI: https://doi.org/10.21660/2015.16.4132
Mohamed Jais IB (2017) Rapid remediation using polyurethane foam/resin grout in Malaysia. Geotechnical Research 4(2):107–117, DOI: https://doi.org/10.1680/jgere.17.00003
Mohammed Al-Bared MA, Marto A (2017) A review on the geotechnical and engineering characteristics of marine clay and the modern methods of improvements. Malaysian Journal of Fundamental and Applied Sciences 13(4):825–831, DOI: https://doi.org/10.11113/mjfas.v13n4.921
Murmu AL, Jain A, Patel A (2019) Mechanical properties of alkali activated fly ash geopolymer stabilized expansive clay. KSCE Journal of Civil Engineering 23(9):3875–3888, DOI: https://doi.org/10.1007/s12205-019-2251-z
Nian T, Jiao H, Fan N, Guo X (2019) Microstructure analysis on the dynamic behavior of marine clay in the South China Sea. Marine Georesources & Geotechnology, 1–14, DOI: https://doi.org/10.1080/1064119X.2019.1573864
Olgun M, Yıldız M (2010) Effect of organic fluids on the geotechnical behavior of a highly plastic clayey soil. Applied Clay Science 48(4): 615–621, DOI: https://doi.org/10.1016/j.clay.2010.03.015
Pakir F, Marto A, Mohd Yunus NZ, Tajudin SAA, Tan CS (2015) Effect of sodium silicate as liquid based stabilizer on shear strength of marine clay. Jurnal Teknologi 76(2):45–50
Phetchuay C, Horpibulsuk S, Arulrajah A, Suksiripattanapong C, Udomchai A (2016) Strength development in soft marine clay stabilized by fly ash and calcium carbide residue based geopolymer. Applied Clay 127(128):134–142, DOI: https://doi.org/10.1016/j.clay.2016.04.005
Priddy LP, Jersey SR, Reese CM (2010) Full-scale field testing for injected foam stabilization of portland cement concrete repairs. Transportation Research Record: Journal of the Transportation Research Board 2155(1):24–33, DOI: https://doi.org/10.3141/2155-03
Ramesh S, Punithamurthy K (2017) The effect of organoclay on thermal and mechanical behaviours of thermoplastic polyurethane nanocomposites. Digest Journal of Nanomaterials and Biostructures 12(2):331–338
Rahman ZA, Yaacob WZW, Rahim SA, Lihan T, Idris WMR, Mohd Sani WNF (2013) Geotechnical characterisation of marine clay as potential liner material. Sains Malaysiana 42(8):1081–1089
Saleh S, Asmawisham Alel MN, Mohd Yunus NZ, Ahmad K, Ali N, Abang Hasbollah DZ, Asnida Abdullah R (2019a) Geochemistry characterisation of marine clay. IOP Conference Series: Materials Science and Engineering 527:012023, DOI: https://doi.org/10.1088/1757-899X/527/1/012023
Saleh S, Mohd Yunus NZ, Ahmad K, Ali N (2018) Stabilization of marine clay soil using polyurethane. MATEC Web of Conferences 250:01004, DOI: https://doi.org/10.1051/matecconf/201825001004
Saleh S, Mohd Yunus NZ, Ahmad K, Ali N (2019b) Improving the strength of weak soil using polyurethane grouts: A review. Construction and Building Materials 202:738–752, DOI: https://doi.org/10.1016/j.conbuildmat.2019.01.048
Shaikh FUA, Supit SWM, Sarker PK (2014) A study on the effect of nano silica on compressive strength of high volume fly ash mortars and concretes. Materials & Design 60:433–442, DOI: https://doi.org/10.1016/j.matdes.2014.04.025
Valentino R Stevanoni D (2016) Behaviour of reinforced polyurethane resin micropiles. Proceedings of the Institution of Civil Engineers — Geotechnical Engineering 169(2):187–200, DOI: https://doi.org/10.1680/jgeen.14.00185
Vennapusa PKR, Zhang Y, White DJ (2016) Comparison of pavement slab stabilization using cementitious grout and injected polyurethane foam. Journal of Performance of Constructed Facilities 30(6): 04016056, DOI: https://doi.org/10.1061/(ASCE)CF.1943-5509.0000916
Vipulanandan C, Kazez MB, Henning S (2012) Pressure-temperature-volume change relationship for a hydrophilic polyurethane grout. Proceedings of the 4th international conference on grouting and deep mixing, February 15–18, Reston, VA, USA, 1808–1818
Vlad S, Ciobanu C, Butnaru M, Macocinschi D, Filip D, Gradinaru LM, Mandru M (2011) Preparation of polyurethane microspheres by electrospray technique. Digest Journal of Nanomaterials and Biostructures 6(2):643–652
Wei Y, Wang F, Gao X, Zhong Y (2017) Microstructure and fatigue performance of polyurethane grout materials under compression. Journal of Materials in Civil Engineering 29(9):04017101, DOI: https://doi.org/10.1061/(ASCE)MT.1943-5533.0001954
Wu D, Xu W, Tjuar R (2015a) Improvements of marine clay slurries using chemical-physical combined method (CPCM). Journal of Rock Mechanics and Geotechnical Engineering 7(2):220–225, DOI: https://doi.org/10.1016/j.jrmge.2015.02.001
Wu H, Zhu M, Liu Z, Yin J (2015b) Developing a polymer-based crack repairing material using interpenetrate polymer network (IPN) technology. Construction and Building Materials 84:192–200, DOI: https://doi.org/10.1016/j.conbuildmat.2015.03.067
Yang Z, Zhang X, Liu X, Guan X, Zhang C, Niu Y (2017) Flexible and stretchable polyurethane/waterglass grouting material. Construction and Building Materials 138:240–246, DOI: https://doi.org/10.1016/j.conbuildmat.2017.01.113
Yi Y, Gu L, Liu S (2015) Microstructural and mechanical properties of marine soft clay stabilized by lime-activated ground granulated blastfurnace slag. Applied Clay Science 103:71–76, DOI: https://doi.org/10.1016/j.clay.2014.11.005
Zhang M, Zhao M, Zhang G, Sietins JM, Granados-Focil S, Pepi MS, Xu Y, Tao M (2018) Reaction kinetics of red mud-fly ash based geopolymers: Effects of curing temperature on chemical bonding, porosity, and mechanical strength. Cement and Concrete Composites 93:175–185, DOI: https://doi.org/10.1016/j.cemconcomp.2018.07.008
Zhou N, Ouyang S, Cheng Q, Ju F (2019) Experimental study on mechanical behavior of a new backfilling material: Cement-treated marine clay. Advances in Materials Science and Engineering 2019:1–8, DOI: https://doi.org/10.1155/2019/1261694
Acknowledgements
The authors are grateful to the funding of Fundamental Research Grant Universiti Teknologi Malaysia Malaysia, Vot no RJ130000.7851.5F197. The first author is also grateful to the support of Tertiary education trust fund (TFUND) Nigeria.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Saleh, S., Yunus, N.Z.M., Ahmad, K. et al. Micro-Level Analysis of Marine Clay Stabilised with Polyurethane. KSCE J Civ Eng 24, 807–815 (2020). https://doi.org/10.1007/s12205-020-1797-0
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12205-020-1797-0