Abstract
A Rayleigh number based criterion is developed for predicting the formation of freckles in Ni-base superalloy castings. This criterion relies on finding the maximum local Rayleigh number in the mush, where the ratio of the driving buoyancy force to the retarding frictional force is the largest. A critical Rayleigh number for freckle formation of approximately 0.25 is found from available experimental data on directional solidification of a Ni-base superalloy. If the Rayleigh number in a superalloy casting is below this critical value, freckles are not expected to form. Full numerical simulations of freckling in directional solidification of superalloys are conducted for a large variety of casting conditions, alloy compositions, and inclinations of the system with respect to gravity. For the vertical cases, the Rayleigh numbers at the starting points of the predicted freckles are in good agreement with the critical value established from the experiments. The simulations confirm that the same critical Rayleigh number applies to different superalloys. The simulations for inclined domains show that even a small amount of inclination (less than 10 deg) significantly lowers the critical Rayleigh number and moves the freckles to the side wall of the casting, where the mushy zone has advanced the most relative to gravity. In application of the Rayleigh number criterion to complex-shaped superalloy castings, the absence of freckles near upper and lower boundaries and in sections of insufficient cross-sectional area or height needs to be taken into account as well. The criterion can be used to study the tradeoffs between different superalloy compositions, applied temperature gradients, and casting speeds. Additional experiments, in particular for other superalloys and for a range of inclinations, are desirable to confirm the critical Rayleigh numbers found in the present study.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
R.J. McDonald and J.D. Hunt: TMS-AIME, 1969, vol. 245, pp. 1993–97.
A.F. Giamei and B.H. Kear: Metall. Trans., 1970, vol. 1, pp. 2185–92.
M.G. Worster: Ann. Rev. Fluid Mech., 1997, vol. 29, pp. 91–122.
A. Hellawell, J.R. Sarazin, and R.S. Steube: Phil. Trans. R. Soc. London A, 1993, vol. 345, pp. 507–44.
T.M. Pollock and W.H. Murphy: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 1081–94.
J.P. Gu, C. Beckermann, and A.F. Giamei: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 1533–42.
S.M. Copley, A.F. Giamei, S.M. Johnson, and M.F. Hornbecker: Metall. Trans., 1970, vol. 1, pp. 2193–2204.
A.K. Sample and A. Hellawell: Metall. Trans. A, 1984, vol. 15A, pp. 2163–73.
J.R. Sarazin and A. Hellawell: Metall. Trans. A, 1988, vol. 19A, pp. 1861–71.
S.N. Tewari and R. Shah: Metall. Trans. A, 1992, vol. 23A, pp. 3383–92.
S.N. Tewari, R. Shah, and M.A. Chopra: Metall. Trans. A, 1993, vol. 24A, pp. 1661–69.
S.N. Tewari and R. Shah: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 1353–62.
M.I. Bergman, D.R. Fearn, J. Bloxham, and M.C. Shannon: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 859–66.
P. Auburtin, S.L. Cockcroft, and A. Mitchell: in Solidification Processing 1997, J. Beech and H. Jones, eds., The University of Sheffield, Sheffield, United Kingdom, 1997, pp. 336–40.
W. Kurz and D.J. Fisher: Fundamentals of Solidification, Trans Tech Publications, Aedermannsdorf, Switzerland, 1998.
P.N. Quested and M. McLean: Mater. Sci. Eng., 1984, vol. 65, pp. 171–84.
G.K. Bouse and J.R. Mihalisin: in Superalloys, Supercomposites and Superceramics, J.K. Tien and T. Caulfield, eds., Academic Press, Boston, MA, 1988, pp. 99–148.
S. Tait and C. Jaupart: J. Geophys. Res., 1992, vol. 97, pp. 6735–56.
A.C. Fowler: IMA J. Appl. Math., 1985, vol. 35, pp. 159–74.
P. Nandapurkar, D.R. Poirier, J.C. Heinrich, and S. Felicelli: Metall. Trans. B, 1989, vol. 20B, pp. 711–21.
M.G. Worster: J. Fluid Mech., 1992, vol. 237, pp. 649–69.
G. Amberg and G.M. Homsy: J. Fluid Mech., 1993, vol. 252, pp. 79–98.
D.M. Anderson and M.G. Worster: J. Fluid Mech., 1995, vol. 302, pp. 307–31.
W.D. Bennon and F.P. Incropera: Int. J. Heat Mass Transfer, 1987, vol. 30, pp. 2161–70.
C. Beckermann and C.Y. Wang: in Annual Review of Heat Transfer VI, C.L. Tien, ed., Begell House, New York, NY, 1995, vol. 6, pp. 115–98.
P.J. Prescott and F.P. Incropera: in Advances in Heat Transfer, D. Poulikakos, ed., Academic Press, San Diego, CA, 1996, pp. 231–338.
M.C. Schneider, J.P. Gu, C. Beckermann, W.J. Boettinger, and U.R. Kattner: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 1517–31.
W.J. Boettinger, U.R. Kattner, S.R. Coriell, Y.A. Chang, and B.A. Mueller: in Modeling of Casting, Welding and Advanced Solidification Process VII, M. Cross and J. Campbell, eds., TMS, Warrendale, PA, 1995, pp. 649–56.
S.D. Felicelli, D.R. Poirier, and J.C. Heinrich: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 847–55.
B. Mueller: Howmet Corporation, Whitehall, MI, personal communication, 1995.
M.C. Bhat: Ph.D. Thesis, The University of Arizona, Tucson, AR, 1995.
J.P. Gu and C. Beckermann: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 1357–66.
T.G. Chart, J.F. Counsell, W. Slough, and P.J. Spencer: Int. Met. Rev., 1975, vol. 20, p. 57.
U.R. Kattner, W.J. Boettinger, and S.R. Coriell: Z. Metallkd., 1996, vol. 87, pp. 522–28.
T. Iida and R.I.L. Guthrie: in The Physical Properties of Liquid Metals, Clarendon Press, Oxford, United Kingdom, 1993, pp. 70–73.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Beckermann, C., Gu, J.P. & Boettinger, W.J. Development of a freckle predictor via rayleigh number method for single-crystal nickel-base superalloy castings. Metall Mater Trans A 31, 2545–2557 (2000). https://doi.org/10.1007/s11661-000-0199-7
Received:
Issue Date:
DOI: https://doi.org/10.1007/s11661-000-0199-7