Abstract
A 2D and a 3D discrete element model (DEM) simulation of cohesive spherical particles are applied to assess the benefit of point source vibration to induce flow in wedge-shaped hoppers. The model is closely compared with a continuum model based on arch stability. A significant aspect of this study is the scaling of the continuum system to a discrete system of 500 particles in 2D and 2500 particles in 3D. This illustrates how such models can complement each other. The continuum model can cope with a full-scale industrial system, but is complex with significant assumptions. The discrete approach is relatively simple at the particle level with minimal assumptions but computationally demanding. The DEM model supports the basic conclusions of the continuum model. The vibration source must be located at the appropriate height above the outlet on the hopper to optimise its flow enhancement. Too low and stable arches can form above. Too high and it might not break the stable arches in the material below. The passive/active nature of the material during vibration and flow is also illustrated. The DEM model also shows that low frequency high amplitude vibration can enable flow through small orifices.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
References
Jenike A.W.: Quantitative design of mass-flow bins. Powder Technol. 1(4), 237–244 (1967)
Enstad G.: On the theory of arching in mass flow hoppers. Chem. Eng. Sci. 30, 1273–1283 (1975)
Williams J.C.: The rate of discharge of coarse granular materials from conical mass flow hoppers. Chem. Eng. Sci. 32, 247–255 (1977)
Langston P.A., Nikitidis M.S., Tuzun U., Heyes D.M., Spyrou N.M.: Microstructural simulation and imaging of granular flows in two- and three-dimensional hoppers. Powder Technol. 94(1), 59–72 (1997)
Kozichi J., Tejchman J.: Application of a cellular automation to simulations of granular flow in silos. Granular Matter 7, 45–54 (2005)
Kamath S., Puri V.M., Manbeck H.B., Hogg R.: Flow properties of powders using four testers—measurement, comparison and assessment. Powder Technol. 76(3), 277–289 (1993)
Arnold P.C.: Flow properties for mass-flow hopper geometry determinations—what range of shear testing is required. Powder Handling Process 15(5), 315–317 (2003)
IMechE conference, Hopper & Silo Discharge: Successful Solutions, IMechE, London, 27 November (1998)
Bradley, M.: Strategy for Selecting Solutions, paper 13, Hopper & Silo Discharge: Successful Solutions, IMechE, London, 27 November (1998)
Roberts, A.W.: Chapter 5. In: Fayed, M.E., Otten, L. (eds.) Handbook of Powder Science and Technology, 2nd edn. Chapman & Hall, New York (1997)
Matsusaka S., Urakawa M., Masuda H.: Micro-feeding of a fine powder using a capillary tube with ultrasionic vibration. Adv. Powder Technol. 6(4), 283–293 (1995)
Matsusaka S., Yamamoto K., Hiraoki H.: Micro-feeding of a fine powder using a vibrating capillary tube. Adv. Powder Technol. 7(2), 141–151 (1996)
Matsusaka, S., Urakawa, M., Furutate, M., Masuda, H.: Micro-feeding of fine powders using a capillary with ultrasonic vibration. In: Third World Congress on Particle Technology, paper 343, Brighton, England, June (1998)
Matchett A.J.: A theoretical model of vibrationally induced flow in conical hopper systems. Chem. Eng. Res. Des. 82(A1), 85–98 (2004)
Walker D.M.: An approximate theory for pressure and arching in hoppers. Chem. Eng. Sci. 21, 975–997 (1966)
Walters K.: A theoretical analysis of stresses in silos with vertical walls. Chem. Eng. Sci. 28, 13–21 (1973)
Asmar B.N., Langston P.A., Matchett A.J., Walters J.K.: Validation tests on a distinct element model of vibrating cohesive particle systems. Comput. Chem. Eng. 26(6), 785–802 (2002)
Fraige F., Langston P.A.: Integration schemes and damping algorithms in distinct element models. Adv. Powder Technol. 15(2), 227–246 (2004)
Li J., Langston P.A., Webb C., Dyakowski T.: Flow of sphero-disc particles in rectangular hoppers—a DEM and experimental comparison in 3D. Chem. Eng. Sci. 59(24), 5917–5929 (2004)
Fraige, F.Y., Langston, P.A., Chen, G.Z.: Distinct element modelling of cubic particle packing and flow. Powder Technol. (in press)
Joseph Anthony, S., Hoyle, W., Ding, Y. (eds.) Review of Granular Materials—Fundamentals and Applications, The Royal Society of Chemistry, Cambridge (2004)
Langston, P.A., Heyes, D.M., Tüzün, U.: Discrete element simulation of granular flow in 2D and 3D hoppers: dependence of discharge rate and wall stress on particle interactions. Chem. Eng. Sci. 50, 967 (1995)
Yang R.Y., Jayasundara C.T., Yu A.B., Curry D.: DEM simulation of the flow of grinding media in IsaMill. Miner. Eng. 19, 984–994 (2006)
Nedderman R.M.: Statics and kinematics of granular materials. Cambridge University Press, Cambridge (1992)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Langston, P.A., Matchett, A.J., Fraige, F.Y. et al. Vibration induced flow in hoppers: continuum and DEM model approaches. Granular Matter 11, 99–113 (2009). https://doi.org/10.1007/s10035-009-0125-7
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10035-009-0125-7