Abstract
In this script, authors affirm a novel structure of tunnel FET in which a lightly doped channel region completely bounds the ultra-thin finger-like source region to enhance the tunneling probability with an increased tunneling interface area. TFETs have become common in power-constrained applications due to the minimal subthreshold swing (SS) and low OFF current (\(I_\mathrm{{off}}\)) with low ON-state driving current (\(I_\mathrm{{on}}\)) and ambipolar conduction concerns. Decreasing device dimensions is becoming more crucial for protecting device linearity and reliability under varying manufacturing and environmental conditions. However, changes in ambient temperature (T) imply its efficiencies, such as linearity distortion, analogue, and high-frequency performance, which must be thoroughly investigated. The impactful analysis was carried out for manuscript for assuring analog/RF performance, linearity distortion, and reliability of F-shaped TFET. Extensive investigations have been performed to check device susceptibility towards temperature ranging from 250 to 400 K by using the 2D-TCAD tool. For this, various critical parameters like \(I_\mathrm{{on}}\), \(I_\mathrm{{ambi}}\), SS, parasitic capacitances, threshold voltage (\(V_\mathrm{{th}}\)), \(I_\mathrm{{on}}/I_\mathrm{{off}}\) ratio, transconductance (\(g_{m}\)), output transconductance (\(g_\mathrm{{ds}}\)), higher-order \(g_{m}\) (\(g_{m2}\) and \(g_{m3}\)), intrinsic gain (IG), cut-off frequency (\(f_{t}\)), gain bandwidth product (GBP), transconductance generation factor (TGF), transit time (TT), transconductance frequency product (TFP), VIP2, VIP3, IIP3, IMD3 and 1-dB compression point have been investigated for temperature sensitivity analysis for the proposed device. Furthermore, reliability analysis is also performed, which shows that with a significant change in second harmonics, rising temperature is seen to be unfavorable for the SS, \(I_\mathrm{{ambi}}\) and \(I_\mathrm{{on}}/I_\mathrm{{off}}\) ratio.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
Downscaling of metal oxide semiconductor field-effect transistors (MOSFETs) has been performed over the years and years to improve device efficiency in terms of \(I_\mathrm{{on}}\), high-frequency parameters, and reliability of the device, to satisfy semiconductor industries demands and continue to realize Moore’s vision [1]. On the other hand, continuous downscaling leads to several critical problems like hot carrier effect, high leakage current, short channel effects, and drain-induced barrier lowering (DIBL), and those are causative for high power consumption [2]. These limitations are labeled as a significant barrier to device reliability. Apart from this, the SS value of MOSFET (switching speed) is limited by thermal factor kT/q. In an ideal case, the minimum SS value of MOSFET is 60 mV/decade, but it may be worst in practical case [3]. To overcome the limitation of MOSFET, an extensive study is carried out on the forthcoming device named tunnel FET (TFET) for its substitute. TFET devices offer very low SS without any limitation with very low leakage current in the range of femto (\(10^{-15}\)) ampere [4, 5]. Along with these substantial advantages, high \(I_\mathrm{{ambi}}\), lower \(I_\mathrm{{on}}\), and poor high-frequency performance are considerable problems of TFET devices. To improve the TFET performance for real-world application (like biosensor, memories, logic gates), many researchers have been working to enhance the \(I_\mathrm{{on}}\) with suppress ambipolar conduction by using different concepts, and engineering techniques [6,7,8]. We need better electrically characteristics for analog/RF applications along with better linearity and reliability performance under the various environmental conditions like impact of temperature variation, power supply fluctuation, etc. Theses variations are responsible for intermodulation, and harmonic distortions [9]. Thus, these effects must be carefully investigated for the device reliability and linearity performance check. Therefore, this proposed work is devoted to a detailed analysis of temperature effect on analog/RF, linearity, and reliability performance, which can be benchmark/solution for real-time application.
To overcome the limitation of conventional TFET like low \(I_\mathrm{{on}}\), high \(I_\mathrm{{ambi}}\), high \(V_\mathrm{{th}}\) etc., we proposed a new structure with an ultra-thin finger-like source with increased S–C-I for better B2BT probability at source/channel junction. The proposed device is named as single gate F-TFET (SG-F-TFET) because of ultra-thin finger-like source which is wholly inserted in the channel region [10]. As we know, the basic working principle of TFET mainly depended on the B2BT at S–C-I (for \(I_\mathrm{{on}}\)) and D–C-I (for ambipolar conduction). So, in this proposed device, the S–C-I junction area is increased to enhance \(I_\mathrm{{on}}\) by increasing the B2BT rate of the carrier at S–C-I, and D–C-I boundary is reduced to limit the ambipolar behavior by widening the width of potential barrier present at D–C-I junction. As we know, the performance of nano-devices is empathetic towards temperature variation [11], and an extensive study is carried to analyze the impact of temperature variation on SG-F-TFET for future replacement in the high-frequency application. The linearity and reliability analysis also performed because adjacent channel signals interface with the original signal and crumble data quality in the high-frequency application. Maintaining linearity metrics within a healthy range is essential.
This script is drafted as follows. First, the DC performance of SG-L-TFET has been investigated with OFF-state sensitivity analysis with variation in temperature and different device models. The impact of temperature variation on analog and high-frequency performance parameters is explained in the “Impact on Analog/RF Parameters” section. In Sect. 5, the device linearity’s sensitivity towards various temperature ranges was investigated. In the end, in the “Reliability Analysis” section, the effects of temperature variations on system reliability are discussed with various pie charts.
2 Device Schematic and Parameters
The 2D cross-sectional view of the proposed SG-F-TFET device schematic is illustrated in Fig. 1, and Table 1 showcases the complete device dimension parameters used during the simulation process. In these, silicon (Si) thin film is considered for device. The Si-based doped source region is highly doped (p+), and Si-based drain region (n+) is lightly doped. Molybdenum with \(4\times 10^{15}\) atom/cm2 nitrogen implant dose is used to achieve gate electrode work function (\(WF_\mathrm{{G}}\)) 4.5 eV with SiO2 as gate oxide. The proposed device consists of a single gate with an ultra-thin, highly doped source region that is entirely bounded by the intrinsic channel region. On the other hand, drain region of device is attached to the outside of the channel, due to this D–C-I is reduced and device looks like an L-shaped. For an extensive study of temperature impact on the various performance parameters of the proposed device, some crucial models are also used during the simulation process. Some used important models are standard band-to-band tunneling model (BTBT), band gap narrowing model (BGN), Auger recombination model (Auger), field-dependent mobility model (FLDMOB), concentration-dependent mobility model (CONMOB), Shockley–Read–Hall model (SRH), trap-assisted tunneling model (TAT), etc. Along with these models, Newton’s numerical method was used to provide strong coupling between the resultant equations for better convergence of current. Excluding this, to analyze RF functioning, the frequency is set to 1 MHz. The physic parameters of device used in models equation are listed in Table2 with corresponding values used during simulation process.
In the table, MUN and MUP are the mobility of electron and hole carriers, respectively. BGN.E, BGN.N and BGN.C parameters are material dependent, and it can be defined with the material properties. \(\epsilon _\mathrm{{si}}\) is permittivity of silicon, and \(\epsilon _{sio_2}\) stands for permittivity of gate oxide. \(m^*_\mathrm{e}\) and \(m^*_h\) are effective mass of electron and holes, \(m^*_0\) stands for rest mass (9.11 \(\times 10^{-31}\) kg).
From a fabrication point of view, the possible fabrication process flow to fabricate the device is depicted in Fig. 2 step by step. For this, self-align process would be used to fabricate the proposed device. In brief, the key steps for self-align process flow are as follows: (1) epitaxial layer grown for P+ type silicon layer, active region patterning, and SiO2 hard-mask deposition; (2) Mesa patterning is followed by SiO2 buffer layer deposition; (3) dummy gate deposition and etch-back process with drain region formation with the help of ion implantation and annealing process; (4) for exposure of dummy gate, chemical mechanical polishing can be used; (5) after that for lateral tunneling region epitaxial layer is grown, and at the last (6) oxide/metal gate formed by atomic layer deposition [10, 12,13,14,15].
3 DC performance analysis
This section is edifying the impact of T variation (from 250 to 400 K, with a 50 K gap) on DC performance of SG-F-TFET. At the initial stage of sensitivity analysis of device w.r.t. any external fluctuations under different working conditions, variation in energy band diagram (EBD), transfer characteristics (\(I_\mathrm{{ds}}-V_\mathrm{{gs}}\) curve), \(V_\mathrm{{th}}\) and SS is the best medium to observe.
When T increases above the room temperature, the covalent bond inside the lattice of body material starts to break, and many electron and hole pairs (EHPs) are generated. The generation rate of EHPs is directly propositional to intrinsic carrier concentration of semiconductor (\(n_i\)) [16, 17]. The \(n_i\) is exponentially increased with T as per Eq. 1. Along with this, the variation in T also affects the band profile of device at both interfaces (S–C-I and D–C-I). The relation between energy band (\(E_g\)) and T is given in Eq. 2.
where \(N_a\) is the impurity (donor/acceptor) concentration, kT is the energy term (product of T and Boltzmann constant), \(E_g (300)\) (1.08 eV for Si material) is the band gap at room temperature, \(\alpha \) (\(4.73\times 10^{-4}\) for Si) and \(\beta \) (636 K for Si) are the fitting parameters of body material.
The effect of T fluctuation on EBD at S–C-I and D–C-I is depicted in Fig. 3. The change in EBD at D–C-I is high (Fig. 3b) as compared to EBD at S–C-I for ON-state condition (Fig. 3a). The overall impact of T on band bending of energy bands in ON-state condition is not considerable, and we can say that band bending of energy bands is less sensitive towards T variations. On the other hand, the percentage change in majority charge carriers (charge carriers of source region) is very less for changes in T because the generated EHPs are significantly less as compared to the carrier present in the highly doped source region. Consequently, we have not seen any significant impact of T on \(I_\mathrm{{on}}\) of SG-F-TFET, as depicted in Fig. 4a. The minority charge carrier is inversely proportional to the doping concentration, and it will increase with a rise in T because more numbers of EHPs are generated. Thus, the percentage deviation in minority charge carrier concentration (charge carrier of drain region) is very high [16, 19]. Due to this, the ambipolar conduction increases as well as T increases from 250 to 400 K with interval of 50 K, as shown in Fig. 4b.
To ensure the model accuracy used during simulation, the proposed device is calibrated with experimental results of doped L-shaped tunnel FET (L-TFET) (Ref. [18]). The calibration is done with the same material and physical dimensions as of doped L-TFET. The simulation results authenticate with experimental data as depicted in Fig. 4c. From Fig. 4c, we can see that the simulated results are well matched with the experimental results, which proves the accuracy of the models used in during simulation work.
When ramp \(V_\mathrm{{gs}}\) is applied, the \(I_\mathrm{{ds}}-V_\mathrm{{gs}}\) curve on semi-log scale is divided into three region. The first region is known as OFF-state region (\(V_\mathrm{{gs}} < V_\mathrm{{off}}\) ), the second region known as subthreshold region (0 \(V_\mathrm{{gs}} < V_\mathrm{{th}}\)), and the third region is super-threshold region (\(V_\mathrm{{gs}} > V_\mathrm{{th}}\)). The device switching speed is examined with the help of the \(2_{nd}\) region of \(I_\mathrm{{ds}}-V_\mathrm{{gs}}\) curve because this region describes how fast device conditions change OFF-state to ON-state. In other words, the steepness of the \(I_\mathrm{{ds}}-V_\mathrm{{gs}}\) curve decides the switching speed of device [20, 21]. The steepness of the curve defines the SS, and its mathematical expression is illustrated in Eq. 3.
The SS value is inversely proportional to the steepness of \(I_\mathrm{{ds}}-V_\mathrm{{gs}}\) curve in the subthreshold region. Figure 5a demonstrates that as T increases, the SS value increases (red lines), which is not a good sign for the switching speed of proposed device. On the other hand, \(V_\mathrm{{th}}\) of the proposed device reduces (black lines, Fig. 5a) with a rise in T, and it is beneficial for ultra-low-power application. In addition, an intensive analysis is performed for \(I_\mathrm{{on}}/I_\mathrm{{off}}\) ratio and \(I_\mathrm{{ambi}}\). As we earlier see that \(I_\mathrm{{on}}\) is not significantly affected by T variation, but \(I_\mathrm{{off}}\) shows the opposite behavior (Fig. 4b). The \(I_\mathrm{{on}}/I_\mathrm{{off}}\) ratio of proposed device decreases as T increases (Fig. 5b) because \(I_\mathrm{{on}}\) slightly decreases but \(I_\mathrm{{off}}\) significantly increases with an increment in T. Similarly, the impact of T on \(I_\mathrm{{ambi}}\) is portrayed in Fig. 5c.
3.1 OFF-current analysis
The OFF-state conditions of proposed device are much affected by T variation. T plays a critical role in the reliability of SG-F-TFET for circuit-level applications because the \(I_\mathrm{{on}}/I_\mathrm{{off}}\) ratio is highly affected. The higher \(I_\mathrm{{on}}/I_\mathrm{{off}}\) ratio leads to better switching speed [22,23,24]. Therefore, an extensive study is performed on SG-F-TFET for OFF-state conditions. For this, the impact of models and T both are carefully investigated to extract the optimum T range and models for improved performance of the proposed device. During the simulation process, we opted for BTBT, TAT (trap-assisted tunneling), and SRH (Shockley–Read–Hall) to analyze the effect of T on \(I_\mathrm{{off}}\).
The consequence of BTBT model on \(I_\mathrm{{off}}\) is examined with the help of Eq. 4. From Eq. 4, the BTBT mainly depends on electric field (E = \(E_{g}^*+ \varDelta \varphi \)), body thickness (\(t_{si}\)), dielectric constant of material and oxide (\(\epsilon _{si}\) and \(\epsilon _{ox}\)) and band gap of material (\(E_{g}^*\)). The BTBT models control the \(I_\mathrm{{on}}\) under the high E-field and show less sensitivity towards the T variations [25].
By using Eq. 5, we investigate the impact of the SRH model on proposed devices at various T values. Constant carrier lifetimes (TAUP0 (for hole) and TAUN0 (for electron)) are used in SRH recombination model with dependency on temperature (\(T_L\) term in Eq. 5) and trap energy level (\(E_{TRAP}\)). So, we can easily conclude that T variation significantly affects the OFF-state conduction with the SRH model. Similarly, from Eq. 6, we can say that the TAT model also shows considerable impact on \(I_\mathrm{{off}}\) because it depends on field-dependent functions (\(\varGamma _{n}^{DIRAC}\) and \(\varGamma _{p}^{DIRAC}\)) and all that factor influences SRH model [26].
As we know, due to high T, more number of covalent bond breaks inside the semiconductor lattice and EHPs generated with high thermal energy. Hence, the mobility of carrier gets reduced, and the movement of charge carriers turns in the vibration at a particular coordinate within the lattice. The amount of energy that charge carriers have between two point gets reduced. Consequently, the potential at D–C-I starts decreasing as T increases from 250 to 400 K, shown in Fig. 6a. The E-field is measure of electrostatic force between two charge carriers (either repulsive or attractive). The E-field at D–C-I junction increases with T (Fig. 6b) because generated EHPs significantly increase the minority charge carrier at D–C-I and due to this the electrostatic force between charge carriers increases. But we can see the opposite impact of T at S–C-I junction because carrier concentration is not much affected by generated EHPs and E-field starts decreasing with a rise in T. At thermal equilibrium, the generation and recombination rates balance the net charge carrier density, i.e., total carrier density is constant. As T increases, the generation of carriers is increasing because more covalent bonds are broken at high T [27]. On the other hand, due to mobility saturation, the recombination rate is decreased, as shown in Fig. 6c.
The variation in potential, E-field and recombination rate at D–C-I affects the OFF-state behavior of the proposed device for different models and variations in T. As \(V_\mathrm{{gs}}\) reduces, TAT and SRH models start showing their existence. For very low \(V_\mathrm{{gs}}\), the potential barrier is getting reduced and enables the BTBT mechanism, which helps the carrier to start tunneling across the present barrier. The BTBT, BTBT+SRH, and BTBT+SRH+TAT current components have their region of confinement depending upon E-field at both interfaces (S–C-I and D–C-I) [25]. The BTBT model component is domineering the \(I_\mathrm{{ds}}\) value under high E-field and shows less sensitivity towards T variation, as mentioned in Eq. 4. On the other hand, SRH and TAT models show their presence at low E-field and dominate the \(I_\mathrm{{ds}}\) range, showing high sensitivity towards changes in T. From Fig. 7, we can examine that due to BTBT model consideration, the change in \(I_\mathrm{{ambi}}\) is from \(10^{-20}\) to \(10^{-16}\) A/μm (\(10^4\) time) and at T= 300K, \(I_\mathrm{{ambi}}\) is in the range of \(10^{-18}\) A/μm, which is acceptable for digital circuit application. But, for the SRH and TAT models, \(I_\mathrm{{ambi}}\) \(\approx \) \(10^{-17}\) and \(10^{-13}\) A/μm, respectively, increase when T increases above the T = 250 K, as depicted in Fig. 7. So, we can easily conclude that for lower T, SRH and TAT consequences are weak, and the BTBT again becomes a major and effective tunneling mechanism with less sensitivity towards T variation.
4 Impact on analog/RF parameter
In this section, the consequence of T variations is analyzed w.r.t. different FOMs (figure of merits) associated with high-frequency performance of the proposed device. For RF performance analysis, the first important parameter to be analyzed is parasitic capacitances (gate-to-drain (\(C_\mathrm{{gd}}\)) and gate-to-source (\(C_\mathrm{{gs}}\)) capacitance) associated with the device. The \(C_\mathrm{{gd}}\) and \(C_\mathrm{{gs}}\) play a crucial role in examining the device performance at high frequency because both are responsible for parasitic oscillation at various frequency ranges [28]. From Fig. 8a, the significant increment can be seen in \(C_\mathrm{{gd}}\) data plot because the thermally generated charge carriers in channel region help to increase the inversion layer across the channel. Thus, the potential barrier present between the D–C-I gets reduced when T increases from 250 to 400 K. Due to this, a considerable increment is visualized in \(C_\mathrm{{gd}}\) plot. On the other hand, \(C_\mathrm{{gs}}\) is reduced as T increases (Fig. 8b) because the potential barrier at S–C-I decreases with an increment in T.
To analyze amplification or current driving capability of SG-F-TFET, the \(g_m\) and \(g_\mathrm{{ds}}\) graph is depicted in Fig. 9 for different T values. The reciprocal of output resistance is known as \(g_\mathrm{{ds}}\). For the high amplification ability of a device, \(g_\mathrm{{ds}}\) should be low. The mathematical expression of \(g_m\) and \(g_\mathrm{{ds}}\) is given in Eqs. 7 and 8.
From Eq. 7, \(g_m\) depends on the slope of \(I_\mathrm{{ds}}-V_\mathrm{{gs}}\) curve, i.e., it can be used to determine the switching speed of the device. Higher \(g_m\) is required for high switching speed. From Fig. 9a we can see that \(g_m\) is reduced as T increases because the \(I_\mathrm{{on}}\) decreases at elevated temperature. On the other hand, \(g_\mathrm{{ds}}\) shows opposite behavior towards T, i.e., it is increased when T rises from 250 to 400 K with 50 K interval (Fig. 9b), which is not a good sign for amplification ability of the device. Along with this, to analyze the impact of T variation on DC and analog parameters, a comparison of parametric deviations is listed in Table 3.
From Eq. 9, the ratio of \(g_m\) and \(g_\mathrm{{ds}}\) is known as intrinsic gain (IG), which is the maximum voltage gain [29, 30]. In this relation, \(g_m\) is dominating factor because \(g_\mathrm{{ds}}\) is very low as compared to the \(g_m\). Therefore, the impact of T on IG plot is similar to \(g_m\) and curve of IG started decreasing as T increases. Similarly, we need to analyze the variation in \(f_t\) at which voltage gain and current gain are equal to unity. The \(f_t\) is directly proportional to \(g_m\) and inversely proportional to total gate capacitance (\(C_{gg}\) = \(C_\mathrm{{gd}}+C_\mathrm{{gs}}\)), as mentioned in Eq. 10. For the lower \(V_\mathrm{{gs}}\), \(g_m\) is dominating but as well as \(V_\mathrm{{gs}}\) increases, \(C_{gg}\) become dominating parameter. Thus, \(f_t\) curve starts decreasing after attaining peak because of high \(C_{gg}\) at higher \(V_\mathrm{{gs}}\). From Fig. 10b, the \(f_t\) curve shifted downward as T increases above the room temperature because variation in \(g_m\) is very high as compared to \(C_\mathrm{{gd}}\) and \(C_\mathrm{{gs}}\) when T increases.
Another crucial parameter for RF analysis is TT depicted in Eq. 11. It is inversely proportional to \(f_t\). The TT increases for reducing \(f_t\) values, and the speed of SG-F-TFET increases because of reduced delay [17, 31]. But for higher T values, TT has reduced because \(f_t\) decreases when T increases from 250 to 400 K, as illustrated in Fig. 11b. Furthermore, the mathematical equation for GBP is given in Eq. 12, which shows the dependency of GBP on \(g_m\) and \(C_\mathrm{{gd}}\). The GBP data plot of SG-F-TFET is illustrated in Fig. 11a for various T values. From this, we examine that the GBP decreases with T and attains its extreme point earlier, and after that, it starts decreasing because \(g_m\) decreases and \(C_\mathrm{{gd}}\) increases.
The mathematical expression of TFP and TGF is given in Eqs. 13 and 14. TFP and TGF are key parameters to consider when calculating device efficiency and the trade-off between operating bandwidth and power dissipation [32, 33]. The TFP and TGF data plot with T variation is depicted in Fig. 12a, b, respectively. From Fig. 12b, the TFP deteriorates at high T, and the maximum peak of TFP is shifted towards lower \(V_\mathrm{{gs}}\) because the mobility of charge carrier at high T decreases. Similarly, the impact of T variation on TGF plot is portrayed in Fig. 12a. From Eq. 14, it inversely depends on \(I_\mathrm{{ds}}\) and directly proportional to \(g_m\). Therefore, TGF is reduced with a rise in T because of decrement in \(g_m\) and \(I_\mathrm{{ds}}\) values.
5 Impact on linearity performance
In the recent trend of device and circuit applications, high \(I_\mathrm{{on}}\), high \(I_\mathrm{{on}}/I_\mathrm{{off}}\) ratio, low \(V_\mathrm{{th}}\) and lower values of SS with suppressed \(I_\mathrm{{ambi}}\) (\(10^{-18}\) \(A/\mu m\)) are not only essential parameters to analyze the device behavior. Linearity analysis of the device is an additional quality checking stage, at which the device is used in the circuit and checks the linear relation between input and output. Any nonlinear power series can be written in the following form by using the Volterra series:
In Table 4, different frequency components of desirable inter-modulated (IMS) and harmonics signal are listed. The desired frequency is \(f_1\) and \(f_2\) with the second- and third-order components. As integral multiples of fundamental frequency give harmonic distortion that can be filtered, they are very far from the desirable range. The IMS of \(f_1{\pm }f_2\) is very close to original frequencies and is hard to remove [34]. The small-signal model (SSM) of output current in terms of nonlinear \(g_m\) for \(V_\mathrm{{gs}}\) can be expressed similar to Eq. 15 and given by
The relation between \(I_\mathrm{{ds}}\) and \(V_\mathrm{{gs}}\) should be linear, but when the \(V_\mathrm{{gs}}\) increases, the \(I_\mathrm{{ds}}\) is saturated because of the mobility saturation of charge carriers and due to this \(g_m\) decreases. As a conclusion of Eq. 16, it is clear that higher-order \(g_m\) derivatives (\(g_{m2}\) and \(g_{m3}\)) should be as minimum as possible for the device to be linear [35]. A detailed investigation of linearity FOMs of SG-F-TFET device under the T variation from 250 to 400 K is performed in this section.
5.1 Harmonic distortions
The mathematical expression of second- and third-order derivatives of \(g_m\) is given in Eqs. 17 and 18, respectively, which are responsible for harmonic distortion and affects the device performance when used in circuit application [36]. The \(g_{m2}\) and \(g_{m3}\) should be low to maintain the linear behavior of SG-F-TFET device. The variation of \(g_{m2}\) and \(g_{m3}\) with respect to \(V_\mathrm{{gs}}\) for different T values is depicted in Fig. 13a, b. The zero cross over point is the value of \(V_\mathrm{{gs}}\) at which \(g_{m2}\) and \(g_{m3}\) become equal to zero, which are defining the optimal bias point for device linear operation and both increase with \(V_\mathrm{{gs}}\). \(g_{m2}\) and \(g_{m3}\) values low for lower T, as shown in Fig. 13. Hence, lower T provides improved linearity performance with suppressed second- and third-order harmonics of \(g_m\).
5.2 Second- and third-order intercept point
In this section, we examine the effect of T variation on the second-order voltage intercept point (\(\text{VIP}_2\)), third-order voltage intercept point (\(\text{VIP}_3\)) and third-order input intercept point (\(IIP_3\)). From Eq. 19, \(\text{VIP}_2\) is the four times of the ratio of \(g_m\) and \(g_{m2}\). As we discussed earlier, for better device performance we need high \(g_m\) and low \(g_{m2}\), so larger value of \(\text{VIP}_2\) is intended to insure better linearity of SG-F-TFET. The value of \(\text{VIP}_2\) decreases, while T increases from 250 to 400 K, shown in Fig. 14a. Therefore, \(\text{VIP}_2\) can be obtained for lower T.
From Eq. 20, \(\text{VIP}_{3}\) directly depends on \(g_m\) and inversely on \(g_{m3}\), so higher value of \(\text{VIP}_{3}\) is desired to ensure suppression of the third-order harmonics with lower value of \(g_{m3}\). \(\text{VIP}_{3}\) improves as T increases above the room temperature, as illustrated in Fig. 14b. The peak of \(\text{VIP}_{3}\) is shifted towards lower \(V_\mathrm{{gs}}\) as T increases, which helps to improve linearity of proposed device and it can be achieved at a lower bias point. This indicates that the proposed device has low power consumption.
The mathematical expression of \(IIP_{3}\) is shown in Eq. 21, where \(R_s\) = 50 \(\varOmega \) for analog and RF application. For better linearity performance, \(IIP_{3}\) should be high because for this we need low \(g_{m3}\) and high \(g_m\) with fixed value of \(R_s\). For lower \(V_\mathrm{{gs}}\) (0 to 0.25 V), \(IIP_{3}\) is improved when T increases, but for higher values of \(V_\mathrm{{gs}}\), it shows asymmetric behavior towards T variation. The \(1^{st}\) and \(2^{nd}\) peaks of \(IIP_{3}\) occur for T = 350 K and T = 250 K, respectively. So, better \(IIP_{3}\) can be achieved at high T.
5.3 Intermodulation distortion and 1-dBm point
Equations 22 and 23 show the mathematical expressions of third-order intermodulation distortion (IMD3) and 1-dB compression point (1-CP), respectively. The IMD3 is directly proportional to the product of \((\text{VIP}_3)^4\) and \((g_{m3})^2\), so reduced value of \(g_{m3}\) helps to achieve the lower range of IMD3. Minimum value of IMD3 indicates better immunity towards the third-order intermodulation harmonics and helps to prevent wastage of usable power. From Fig. 15a, IMD3 increases with T, leading to degradation of device performance.
Another vital parameter to consider when determining the device’s linearity efficacy is the 1-CP. A high value of 1-CP is desired because it specifies the input power level at which the output power reduces to 1 dB from the linear gain region. It is used to calculate the highest input power, after which the device’s gain reduces. 1-CP enhanced as T increases above 250 K, which is a good sign.
6 Reliability analysis
This section highlights the reliability concerns of proposed device over a wide T range of 250 to 400 K. In Sect. 3, we have seen that the impact of T variation on \(I_\mathrm{{on}}\) is very low and \(I_\mathrm{{on}}\) and \(V_\mathrm{{th}}\) reduces as T increases. On the other hand, \(I_\mathrm{{ambi}}\) and SS value of the proposed device increase with temperature. The \(I_\mathrm{{on}}/I_\mathrm{{off}}\) ratio decreases dramatically with increasing T. Similarly, in Sect. 3.1, study on OFF-state elaborates that ambipolar behavior of the proposed device is increased with T because of strong dependency of SRH and TAT model on temperature. The variation in T also affects the high-frequency performance parameters. The percentage deviation in analog and RF parameters is analyzed and depicted in Fig. 16a with the help of a pie chart. The same way, impact on linearity parameters is illustrated in Fig. 16b. Therefore, after a detailed study of ON- and OFF-state, high frequency, and linearity performance of the proposed device, it can be concluded that SG-F-TFET shows better reliability in the range of 250 to 350 K temperature.
7 Conclusion
In this extensive study, TFET with ultra-thin finger-like source region is introduced and investigated under various T ranges from 250 to 400 K with 50 K interval. This proposed device overcomes the limitation of conventional TFET in terms of high \(I_\mathrm{{on}}\) (\(5.45\times 10^{-4}\) \(A/\mu m\)), lower \(V_\mathrm{{th}}\) (0.60 V) and optimum SS (10.08 mV/decade) at T = 300 K. Further, impact of T is examined in ON-state conditions, OFF-state conditions, RF performance, and linearity performance parameters. It has been analyzed that \(I_\mathrm{{on}}\) and \(C_{gg}\) show less sensitivity towards T variations. Hence, SG-F-TFET can be a promising device for ultra-low power and RF applications. On the other side, the impact of T on off-state current is very high, which deteriorates the device performance for digital circuit application. The increase in T reduces the impact of BTBT current component, and TAT and SRH current components get more superiority in the proposed device’s OFF-state condition. Due to this effect, the \(I_\mathrm{{on}}/I_\mathrm{{off}}\) ratio drastically reduces because \(I_\mathrm{{off}}\) increases with the rise in T. Besides, the influence of T variation on RF parameters is also examined, to check the device performance for high-frequency applications, and we find that the sensitivity of RF parameters towards T variation is less. Linearity and reliability analysis is carried out to examine robustness of SG-F-TFET under various environmental conditions. We found that SG-F-TFET shows superior response in the T range of 250 to 350 K.
References
S. Chih-Tang, Evolution of the MOS transistor-from conception to VLSI. Proc. IEEE 76(10), 1280–1326 (1988)
H. Iwai, CMOS technology-year 2010 and beyond. IEEE J. Solid-State Circuits 34(3), 357–366 (1999)
S.-W. Sun, P.G. Tsui, Limitation of CMOS supply-voltage scaling by MOSFET threshold-voltage variation. IEEE J. Solid-state Circuits 30(8), 947–949 (1995)
S.M. Turkane, A. Kureshi, Review of tunnel field effect transistor (tfet). Int. J. Appl. Eng. Res. 11(7), 4922–4929 (2016)
Y. Zhu, M.K. Hudait, Low-power tunnel field effect transistors using mixed As and Sb based heterostructures. Nanotechnol. Rev. 2(6), 637–678 (2013)
D.B. Abdi, M.J. Kumar, Controlling ambipolar current in tunneling FETs using overlapping gate-on-drain. IEEE J. Electron Dev. Soc. 2(6), 187–190 (2014)
A. Vladimirescu, A. Amara, C. Anghel et al., An analysis on the ambipolar current in Si double-gate tunnel FETs. Solid-State Electron. 70, 67–72 (2012)
W.Y. Choi, W. Lee, Hetero-gate-dielectric tunneling field-effect transistors. IEEE Trans. Electron Dev. 57(9), 2317–2319 (2010)
T. Nirschl, P.-F. Wang, W. Hansch, D. Schmitt-Landsiedel, The tunnelling field effect transistors (tfet): the temperature dependence, the simulation model, and its application, in 2004 IEEE International Symposium on Circuits and Systems (IEEE Cat. No. 04CH37512), vol. 3. IEEE, 2004, pp. III–713
S. Yun, J. Oh, S. Kang, Y. Kim, J.H. Kim, G. Kim, S. Kim, F-shaped tunnel field-effect transistor (tfet) for the low-power application. Micromachines 10(11), 760 (2019)
R. Narang, M. Saxena, R. Gupta, M. Gupta, Linearity and analog performance analysis of double gate tunnel FET: effect of temperature and gate stack. Int. J. VLSI Des. Commun. Syst. 2(3), 185 (2011)
W. Ahmed, E. Ahmed, Ion implantation and in situ doping of silicon. Mater. Chem. Phys. 37(3), 289–294 (1994)
A. Gedam, B. Acharya, G.P. Mishra, An analysis of interface trap charges to improve the reliability of a charge-plasma-based nanotube tunnel fet, J. Comput. Electron. 1–12 (2021)
M. Zhang, Y. Guo, J. Zhang, J. Yao, J. Chen, Simulation study of the double-gate tunnel field-effect transistor with step channel thickness. Nanoscale Res. Lett. 15(1), 1–9 (2020)
J.H. Kim, S.W. Kim, H.W. Kim, B.-G. Park, Vertical type double gate tunnelling FETs with thin tunnel barrier. Electron. Lett. 51(9), 718–720 (2015)
N. Liu, Z. Lu, J. Zhao, M.T. McDowell, H.-W. Lee, W. Zhao, Y. Cui, A pomegranate-inspired nanoscale design for large-volume-change lithium battery anodes. Nat. Nanotechnol. 9(3), 187–192 (2014)
R. Narang, M. Saxena, R. Gupta, M. Gupta, Impact of temperature variations on the device and circuit performance of tunnel FET: a simulation study. IEEE Trans. Nanotechnol. 12(6), 951–957 (2013)
S.W. Kim, J.H. Kim, T.-J.K. Liu, W.Y. Choi, B.-G. Park, Demonstration of l-shaped tunnel field-effect transistors. IEEE Trans. Electron Dev. 63(4), 1774–1778 (2015)
N. Parmar, P. Singh, D.P. Samajdar, D.S. Yadav, Temperature impact on linearity and analog/RF performance metrics of a novel charge plasma tunnel FET. Appl. Phys. A 127(4), 1–9 (2021)
K. Boucart, A.M. Ionescu, Double-gate tunnel FET with high-k gate dielectric. IEEE Trans. Electron Dev. 54(7), 1725–1733 (2007)
U.E. Avci, I.A. Young, Heterojunction tfet scaling and resonant-tfet for steep subthreshold slope at sub-9nm gate-length. IEEE International Electron Devices Meeting 2013, 3–4 (2013)
W.Y. Choi, B.-G. Park, J.D. Lee, T.-J.K. Liu, Tunneling field-effect transistors (tfets) with subthreshold swing (ss) less than 60 mv/dec. IEEE Electron Device Lett. 28(8), 743–745 (2007)
P.G. Der Agopian, M.D.V. Martino, S.G. dos Santos Filho, J.A. Martino, R. Rooyackers, D. Leonelli, C. Claeys, Temperature impact on the tunnel fet off-state current components, Solid-State Electron. 78, 141–146 (2012)
G. Hurkx, D. Klaassen, M. Knuvers, F. O’hara, A new recombination model describing heavy-doping effects and low-temperature behaviour. in International Technical Digest on Electron Devices Meeting. IEEE, 1989, pp. 307–310
D.S. Yadav, D. Sharma, R. Agrawal, G. Prajapati, S. Tirkey, B. R. Raad, V. Bajaj, Temperature based performance analysis of doping-less tunnel field effect transistor, in 2017 International Conference on Information, Communication, Instrumentation and Control (ICICIC). IEEE, 2017, pp. 1–6
Q. Smets, A.S. Verhulst, E. Simoen, D. Gundlach, C. Richter, N. Collaert, M.M. Heyns, Calibration of bulk trap-assisted tunneling and Shockley–Read–Hall currents and impact on InGaAs tunnel-FETs. IEEE Trans. Electron Devices 64(9), 3622–3626 (2017)
A. Sproul, M. Green, Improved value for the silicon intrinsic carrier concentration from 275 to 375 k. J. Appl. Phys. 70(2), 846–854 (1991)
J. Madan, R. Chaujar, Gate drain underlapped-PNIN-GAA-TFET for comprehensively upgraded analog/RF performance. Superlattices Microstruct. 102, 17–26 (2017)
S. Saurabh, M.J. Kumar, Novel attributes of a dual material gate nanoscale tunnel field-effect transistor. IEEE Trans. Electron Devices 58(2), 404–410 (2010)
S. Kumar, D. S. Yadav, S. Saraswat, N. Parmar, R. Sharma, A. Kumar, A novel step-channel tfet for better subthreshold swing and improved analog/rf characteristics, in 2020 IEEE International Students’ Conference on Electrical, Electronics and Computer Science (SCEECS). IEEE, 2020, pp. 1–6
D.S. Yadav, B.R. Raad, D. Sharma, A novel gate and drain engineered charge plasma tunnel field-effect transistor for low sub-threshold swing and ambipolar nature. Superlattices and Microstructures 100, 266–273 (2016)
D.S. Yadav, D. Sharma, S. Tirkey, D. Soni, D.G. Sharma, S. Bajpai, N. Sharma, A comparative study of gap, sige hetero junction double gate tunnel field effect transistor, in IEEE International Symposium on Nanoelectronic and Information Systems (iNIS). IEEE , vol. 2017, pp. 195–199 (2017)
P. Singh, D.S. Yadav, Design and investigation of f-shaped tunnel FET with enhanced analog/RF parameters (2021)
P.K. Verma, S.K. Gupta, “Proposal of charge plasma based recessed source/drain dopingless junctionless transistor and its linearity distortion analysis for circuit applications,” Silicon, pp. 1–28, (2020)
M.R. Tripathy, A.K. Singh, K. Baral, P.K. Singh, A.K. Mishra, D.K. Jarwal, S. Jit, Study of temperature sensitivity on linearity figures of merit of Ge/Si hetero-junction gate-drain underlapped vertical tunnel FET with heterogeneous gate dielectric structure for improving device reliability, in 2020 URSI Regional Conference on Radio Science (URSI-RCRS). IEEE, 2020, pp. 1–4
E. Datta, A. Chattopadhyay, A. Mallik, Y. Omura, Temperature dependence of analog performance, linearity, and harmonic distortion for a GE-source tunnel FET. IEEE Trans. Electron Devices 67(3), 810–815 (2020)
Acknowledgements
The authors would like to thank Dr. Dip Prakash Samajdar from the Department of Electronics and Communication Engineering, PDPM Indian Institute of Information Technology, Design and Manufacturing, Jabalpur, Madhya Pradesh, India, for providing valuable suggestions and support to carry out this research work.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Singh, P., Yadav, D.S. Impact of temperature on analog/RF, linearity and reliability performance metrics of tunnel FET with ultra-thin source region. Appl. Phys. A 127, 671 (2021). https://doi.org/10.1007/s00339-021-04813-1
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s00339-021-04813-1