Abstract
This work presents the optimization of weld factors for ultrasonic welding of similar thermoplastics acrylo-nitrile butadiene styrene (ABS) to ABS (ABS/ABS) and polypropylene (PP) to PP (PP/PP) using Taguchi experimental design (L-8). Energy director (ED) fabricated using injection molding is the protruding part for getting ultrasonic vibrations concentrated at the joint interface. Dimensions of ED were increased, as compared to literature, to investigate its effect on joint quality. In addition to enhanced ED dimensions, it was essential to consider the other weld factors properly leading to parametric optimization of these factors for selected thermoplastics. For both ABS and PP, highest lap shear strength (LSS) was achieved while using triangular (TRI) ED instead of SEMI (semi-circular) ED. In the case of ABS, applied pressure, amplitude, and hold time are found to be the significant factors for maximizing LSS; however, amplitude and weld time are found to be more contributing parameters for weld strength in the case of PP. Significant improvement in the weld strength (LSS) has been achieved after conducting the validation experiments for both ABS and PP, i.e., 31.21 MPa (104% of original ABS shear strength) and 22.36 MPa (319% of original PP shear strength) respectively. Substantial enhancement in LSS has been acquired as compared to previous studies. This improvement was only possible with introducing the new joint design for ultrasonic welding that is an innovative design idea. Furthermore, these huge improvements in LSS were never reported for any other welding process utilizing thermoplastics in literature. Although ABS and PP are ductile, various causes of fracture brittleness are also microscopically studied for both materials.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Fernandez Villegas I, Vizcaino RP (2015) On avoiding thermal degradation during welding of high-performance thermoplastic composites to thermoset composites. Compos Part A Appl Sci Manuf 77:172–180. https://doi.org/10.1016/j.compositesa.2015.07.002
Sackmann J, Burlage K, Gerhardy C, Memering B, Liao S, Schomburg WK (2015) Review on ultrasonic fabrication of polymer micro devices. Ultrasonics 56:189–200. https://doi.org/10.1016/j.ultras.2014.08.007
Krabbe S, Achatz DE, Nieradzik T, Gerhardy C, Schomburg WK (2015) Ultrasonic welding of chemical optical sensors supporting O2, pH and CO2 imaging in microfluidic systems. Procedia Eng 120:598–601. https://doi.org/10.1016/j.proeng.2015.08.736
Ultrasonic FAQ’s - Ultrasonic Technology 2015. http://www.sonobondultrasonics.com/more-info/ultrasonic-faqs
Oehm L, Bach S, Majschak JP (2016) Investigations on the heating effect of PE-LD induced by high-intensity focused ultrasound. Ultrasonics 70:204–210. https://doi.org/10.1016/j.ultras.2016.05.002
Singh R, Kumar R, Feo L, Fraternali F (2016) Friction welding of dissimilar plastic/polymer materials with metal powder reinforcement for engineering applications. Compos Part B Eng 101:77–86. https://doi.org/10.1016/j.compositesb.2016.06.082
Lambiase F, Paoletti A, Grossi V, Genna S (2017) Improving energy efficiency in friction assisted joining of metals and polymers. J Mater Process Technol 250:379–389. https://doi.org/10.1016/j.jmatprotec.2017.08.005
Paoletti A, Lambiase F, Di Ilio A (2016) Analysis of forces and temperatures in friction spot stir welding of thermoplastic polymers. Int J Adv Manuf Technol 83:1395–1407. https://doi.org/10.1007/s00170-015-7669-y
Lambiase F, Paoletti A, Di Ilio A (2017) Friction spot stir welding of polymers: control of plunging force. Int J Adv Manuf Technol 90:2827–2837. https://doi.org/10.1007/s00170-016-9586-0
Yan Y, Shen Y, Zhang W, Guan W (2017) Effects of friction stir spot welding parameters on morphology and mechanical property of modified cast nylon 6 joints produced by double-pin tool. Int J Adv Manuf Technol 92:2511–2523. https://doi.org/10.1007/s00170-017-0306-1
Farshbaf ZR (2015) Experimental evaluation of ultrasonic-assisted friction stir process effect on in situ dispersion of multi-walled carbon nanotubes throughout polyamide 6. Int J Adv Manuf Technol 81:2087–2098. https://doi.org/10.1007/s00170-015-7357-y
Lambiase F, Paoletti A, Di Ilio A (2015) Mechanical behaviour of friction stir spot welds of polycarbonate sheets. Int J Adv Manuf Technol 80:301–314. https://doi.org/10.1007/s00170-015-7007-4
Hoseinlaghab S, Mirjavadi SS, Givi MKB, Azarbarmas M (2014) Influences of welding parameters on the quality and creep properties of friction stir welded. J Mater 67:369–378. https://doi.org/10.1016/j.matdes.2014.11.039
Gao J, Li C, Shilpakar U, Shen Y (2016) Microstructure and tensile properties of dissimilar submerged friction stir welds between HDPE and ABS sheets. Int J Adv Manuf Technol 87:919–927. https://doi.org/10.1007/s00170-016-8539-y
Eslami S, Ramos T, Tavares PJ, Moreira PMGP (2015) Shoulder design developments for FSW lap joints of dissimilar polymers. J Manuf Process 20:15–23. https://doi.org/10.1016/j.jmapro.2015.09.013
Pappadà S, Salomi A, Montanaro J, Passaro A, Caruso A, Maffezzoli A (2015) Fabrication of a thermoplastic matrix composite stiffened panel by induction welding. Aerosp Sci Technol 43:314–320. https://doi.org/10.1016/j.ast.2015.03.013
Shi H, Villegas IF, Bersee HEN (2015) A displacement-detection based approach for process monitoring and processing window definition of resistance welding of thermoplastic composites. Compos Part A Appl Sci Manuf 74:1–9. https://doi.org/10.1016/j.compositesa.2015.03.002
Herrmann Ultrasonics I. Ultrasonic welding machine utilizes rotary technology 2016. http://news.thomasnet.com/fullstory/ultrasonic-welding-machine-utilizes-rotary-technology-543973
Parmar U, Pandya DH (2016) Experimental investigation of ultrasonic welding on non-metallic material. Procedia Technol 23:551–557. https://doi.org/10.1016/j.protcy.2016.03.062
Arungalai Vendan S, Chinnadurai T, Senthil Kumar K, Prakash N (2017) Investigations on mechanical and structural aspects of ultrasonic hybrid polymer mixture welding for industrial applications. Int J Adv Manuf Technol 93:89–102. https://doi.org/10.1007/s00170-015-7773-z
Roopa Rani M, Prakasan K, Rudramoorthy R (2015) Studies on thermo-elastic heating of horns used in ultrasonic plastic welding. Ultrasonics 55:123–132. https://doi.org/10.1016/j.ultras.2014.07.005
Cyzewski E. Overview of ultrasonic welding 2016. http://www.bakersgas.com/weldmyworld/overview-of-ultrasonic-welding/
Yousefpour A, Hojjati M, Immarigeon J-P (2004) Fusion bonding/welding of thermoplastic composites. J Thermoplast Compos Mater 17:303–341. https://doi.org/10.1177/0892705704045187
Nonhof CJ, Luiten GA (1996) Estimates for process conditions during the ultrasonic welding of thermoplastics. Polym Eng Sci 36:1177–1183
Suresh KS, Rani MR, Prakasan K, Rudramoorthy R (2007) Modeling of temperature distribution in ultrasonic welding of thermoplastics for various joint designs. J Mater Process Technol 186:138–146. https://doi.org/10.1016/j.jmatprotec.2006.12.028
Villegas IF, Bersee HEN (2010) Ultrasonic welding of advanced thermoplastic composites: an investigation on energy-directing surfaces. Adv Polym Technol 29:112–121. https://doi.org/10.1002/adv.20178
Tsujino J, Hongoh M, Yoshikuni M, Hashii H, Ueoka T (2004) Welding characteristics of 27, 40 and 67 kHz ultrasonic plastic welding systems using fundamental- and higher-resonance frequencies. Ultrasonics 42:131–137. https://doi.org/10.1016/j.ultras.2004.02.009
Tsujino J (1995) Recent developments of ultrasonic welding. 1995 IEEE Ultrason. Symp. Proceedings. An Int Symp 2, IEEE:1051–1060. https://doi.org/10.1109/ULTSYM.1995.495743
Wu YB, Sato T, Qiu JH, Lin WM (2009) Proposal of a new ultrasonic welding technique for thermoplastic polymer. Adv Mater Res 83–86:1129–1134. https://doi.org/10.4028/www.scientific.net/AMR.83-86.1129
Shu KM, Chang CS, Chuang WJ, Wang SI, Jang YY (2010) Study on application of Taguchi method to ultrasonic-aided spin welding of heterogeneous plastic materials. Adv Mater Res 126–128:381–387. https://doi.org/10.4028/www.scientific.net/AMR.126-128.381
Wu C-Y, Benatar A, Mokhtarzadeh A (2012) Comparison of ultrasonic welding and vibration welding of thermoplastic polyolefin. Weld World 56:69–75. https://doi.org/10.1007/BF03321148
Hopmann C, van Aaken A (2014) Ultrasonic welding of polyamide — influence of moisture on the process relevant. Material Properties 58:787–793. https://doi.org/10.1007/s40194-014-0158-3
Liu S-J, Chang I-T (2002) Optimizing the weld strength of ultrasonically welded nylon composites. J Compos Mater 36:611–624. https://doi.org/10.1177/0021998302036005476
Liu S-J, Chang I-T, Hung S-W (2001) Factors affecting the joint strength of ultrasonically welded polypropylene composites. Polym Compos 22:132–141. https://doi.org/10.1002/pc.10525
Liu S-J, Lin W-F, Chang B-C, Wu G-M, Hung S-W (1999) Optimizing the joint strength of ultrasonically welded thermoplastics. Adv Polym Technol 18:125–135. https://doi.org/10.1002/(SICI)1098-2329(199922)18:2<125::AID-ADV3>3.0.CO;2-A
Rani RM, Suresh KS, Prakasan K, Rudramoorthy R (2007) A statistical study of parameters in ultrasonic welding of plastics. Exp Tech 31:53–58. https://doi.org/10.1111/j.1747-1567.2007.00182.x
Chuah YK, Chien LH, Chang BC, Liu SJ (2000) Effects of the shape of the energy director on far-field ultrasonic welding of thermoplastics. Polym Eng Sci 40:157–167. https://doi.org/10.1002/pen.11149
Raza SF, Majewski C, Pinna C (2015) Ultrasonic welding of thermoplastics. The University of Sheffield, UK
Liu S, Lin W, Chang B, College H.1998 Optimizing the joint strength of ultrasonically welded thermoplastics ;18:125–35
Benatar A, Eswaran RV, Nayar SK (1989) Ultrasonic welding of thermoplastics in the near-field. Polym Eng Sci 29:1689–1698. https://doi.org/10.1002/pen.760292311
Ferry JD.1980 Viscoelastic properties of polymers. Third. USA: John Wiley & Sons, Inc.
Ge T, Pierce F, Perahia D, Grest GS, Robbins MO.2012 Polymer welding: strength through entanglements. ArXiv Prepr ArXiv12116796 ;2:1–5
Cantrell J, Rohde S, Damiani D, Gurnani R, DiSandro L, Anton J, et al. 2017 Experimental characterization of the mechanical properties of 3D printed ABS and polycarbonate parts :89–105. doi:https://doi.org/10.1007/978-3-319-41600-7_11
Bagheri A, Azdast T, Doniavi A (2013) An experimental study on mechanical properties of friction stir welded ABS sheets. Mater Des 43:402–409. https://doi.org/10.1016/j.matdes.2012.06.059
Sadeghian N, Besharati Givi MK (2015) Experimental optimization of the mechanical properties of friction stir welded acrylonitrile butadiene styrene sheets. Mater Des 67:145–153. https://doi.org/10.1016/j.matdes.2014.11.032
Pirizadeh M, Azdast T, Rash Ahmadi S, Mamaghani Shishavan S, Bagheri A (2014) Friction stir welding of thermoplastics using a newly designed tool. Mater Des 54:342–347. https://doi.org/10.1016/j.matdes.2013.08.053
Mendes N, Loureiro A, Martins C, Neto P, Pires JN (2014) Effect of friction stir welding parameters on morphology and strength of acrylonitrile butadiene styrene plate welds. Mater Des 58:457–464. https://doi.org/10.1016/j.matdes.2014.02.036
DiBenedetto AT (1985) Evaluation of fiber surface treatments in composite materials. Pure Appl Chem 57:1659–1665. https://doi.org/10.1351/pac198557111659
J. Tsujino, M. Hongoh and T Ueoka. Welding characteristics of 40 kHz ultrasonic plastic welding system using fundamental and higher resonance frequency vibrations. 2002 Ieee Ultrason. Symp. Proceedings, Vols 1 2, 2002, p. 699–72
Kiss Z, Czigány T (2007) Applicability of friction stir welding in polymeric materials. Period Polytech Mech Eng 51:15–18. https://doi.org/10.3311/pp.me.2007-1.02
Procedures E.2003 Characterization and failure analysis of PLASTICS. vol. 307.
Acknowledgments
It is hereby admitted that experimentation in this work has been completed using Lea Lab of The University of Sheffield UK.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Raza, S.F., Khan, S.A. & Mughal, M.P. Optimizing the weld factors affecting ultrasonic welding of thermoplastics. Int J Adv Manuf Technol 103, 2053–2067 (2019). https://doi.org/10.1007/s00170-019-03681-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-019-03681-7