Abstract
Applications of thin-walled parts are substantially affected by residual stress generated during the cutting process. However, in multi-process milling, the redistribution mechanisms of residual stress after roughing, semi-finishing, finishing, and heat treatment are highly complex and remain underexplored. As a result, the control of deformation of multi-process thin-walled parts remains challenging. In this study, to reduce the influence of residual stress on the deformation of complex thin-walled parts, simulation models of the machining process and heat treatment are carried out based on multi-process analysis. By comparing different process parameters, the redistribution mechanism of residual stress during multi-process milling is analyzed. The findings reveal that with a stress-relief treatment between every process, especially before finishing machining, compressive stress on the surface of thin-walled parts is greatly reduced; residual stress on the sub-surface enters a stable state quickly; and the internal metal structure and structural performance are more reliable. Experiments are conducted to verify these results by comparing residual stress. Stress-relief treatment after every cutting process is ultimately recommended for controlling residual stress and deformation of thin-walled parts in multi-process machining.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Gao H, Zhang Y, Wu Q, Li B (2018) Investigation on influences of initial residual stress on thin-walled part machining deformation based on a semi-analytical model. J. Mater. Process. Technol. 262:437–448
Wu C, Pang J, Li B, Liang SY (2019) High speed grinding of HIP-SiC ceramics on transformation of microscopic features. Int. J. Adv. Manuf. Technol. https://doi.org/10.1007/s00170-018-03226-4
Arrazola PJ, Özel T, Umbrello D, Davies M, Jawahir IS (2013) Recent advances in modelling of metal machining processes. CIRP Ann.: Manuf. Technol. 62:695–718
Coto B, Navas VG, Gonzalo O, Aranzabe A, Sanz C (2011) Influences of turning parameters in surface residual stresses in AISI 4340 steel. Int. J. Adv. Manuf. Technol. 53:911–919
Navas VG, Gonzalo O, Bengoetxea I (2012) Effect of cutting parameters in the surface residual stresses generated by turning in AISI4340 steel. Int. J. Mach. Tools Manuf. 61:48–57
Li J, Jing L, Chen M (2009) An FEM study on residual stresses induced by high-speed end-milling of hardened steel SKD11. J. Mater. Process. Technol. 209(9):4515–4520
Masoudi S, Amini S, Saeidi E, Eslami-Chalander H (2015) Effect of machining-induced residual stress on the deformation of thin-walled parts. Int. J. Adv. Manuf. Technol. 76(1-4):597–608
Huang K, Yang W, Ye X (2018) Adjustment of machining-induced residual stress based on parameter inversion. Int. J. Mech. Sci. 135:43–52
Jiang X, Zhu Y, Zhang Z, Guo M, Ding Z (2018) Investigation of residual impact stress and its effects on the precision during milling of the thin-walled part. Int. J. Adv. Manuf. Technol. 97(1-4):877–892
Zhang J, Lin B, Fei J, Huang T, Xiao J, Zhang X, Ji C (2018) Modeling and experimental validation for surface error caused by axial cutting force in end-milling process. Int. J. Adv. Manuf. Technol. 98(1-4):213–222
Kazban RV (2006) Effect of tool parameters on residual stress and temperature generation in high-speed machining of aluminum alloys. Dissertations & Theses – Gradworks 8(2):1120–1120
Mohamed NA, Ng E-G, Elbestawi MA (2007) Modelling the effects of tool-edge radius on residual stresses when orthogonal cutting AISI 316L. Int. J. Mach. Tools. Manuf. 47(2):401–411
Tang Z, Liu Z, Pan Y, Wan Y, Ai X (2009) The influence of tool flank wear on residual stresses induced by milling aluminum alloy. J. Mater. Process. Technol. 09(2):4502–4508
Muñoz-Sánchez A, Canteli JA, Cantero JL, Miguélez MH (2011) Numerical analysis of the tool wear effect in the machining induced residual stresses. Simul. Model Pract. Th. 19:872–886
Huang K, Yang W (2017) Analytical analysis of the mechanism of effects of machining parameter and tool parameter on residual stress based on multivariable decoupling method. Int. J. Mech. Sci. 128:659–679
Jiang X, Zhang Z, Ding ZO (2017) F., Liang, S.Y., Tool overlap effect on redistributed residual stress and shape distortion produced by the machining of thin-walled aluminum parts. Int. J. Adv. Manuf. Technol. 93(5-8):2227–2242
Treuting RG, Read WT (1951) A mechanical determination of biaxial residual stress in sheet materials. J. Appl. Phys. 22(2):130–134
Liu C, Guo Y (2000) Finite element analysis of the effect of sequential cuts and tool-chip friction on residual stresses in a machined layer. Int. J. Mech. Sci. 42:1069–1086
Lee HY, Nikbin KM (2007) Modelling the redistribution of residual stresses at elevated temperature in components. Fatigue Fract. Mech. 35:54–68
Robinson JS, Tanner DA, Truman CE, Wimpory RC (2011) Measurement and prediction of machining induced redistribution of residual stress in the aluminium alloy 7449. Exp. Mech. 51:981–993
Li B, Jiang X, Yang J, Liang SY (2015) Effects of depth of cut on the redistribution of residual stress and deformation during the milling of thin-walled part. J. Mater. Process. Technol. 216:223–233
Third Wave Systems, 2010 Inc., AdvantEdge V5.6-014 machining simulation software. Minneapolis, MN. .
Abaqus I, Systemes D (2013) Analysis user’s manual, version 6.13. Simulia, Paris
Ulutan D, Alaca BE, Lazoglu I (2007) Analytical modeling of residual stresses in machining. J Mater Process Technol. 183:77–87
Lazoglu I, Ulutan D, Alaca BE, Engin S, Kaftanoglu B (2008) An enhanced analytical model for residual stress prediction in machining. CIRP Annals - Manuf Technol. 57:81–84
Liang SY, Su JC (2007) Residual stress modeling in orthogonal machining. CIRP Annals - Manuf Technol 56(1):65–68
Funding
This study was financially supported by the Shanghai Sailing Program (no. 18YF1418400).
Author information
Authors and Affiliations
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Guo, M., Jiang, X., Ye, Y. et al. Investigation of redistribution mechanism of residual stress during multi-process milling of thin-walled parts. Int J Adv Manuf Technol 103, 1459–1466 (2019). https://doi.org/10.1007/s00170-019-03640-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-019-03640-2