Abstract
Air is one of the most important processing parameters in electromagnetic sheet metal forming processes, especially when forming a large-scale sheet via single discharge or controlling dimensional accuracy with the die fitness of the deformed workpiece. Previous research on electromagnetic sheet forming mostly concentrated on the effects of magnetic pressure distribution, discharge energy, and material properties on workpiece deformation behavior. In this paper, the effect of air on electromagnetic sheet forming is investigated and the research contents are mainly divided into the following three parts: (1) investigating the influence of thickness, material strength, and die caliber on pre-deformation of the sheet when the die cavity is an approximate vacuum via simulation and experimentation; (2) studying the effect of workpiece pre-deformation on electromagnetic sheet forming with regard to the magnitude and distribution of the electromagnetic force, deformation velocity, workpiece profile, etc.; and (3) investigating the influence of the resistance generated by the residual die cavity air on workpiece deformation with experiments considering the die fitness of the deformed workpiece. The results show that atmospheric pressure results in workpiece pre-deformation when the die cavity is near vacuum and the pre-deformation is closely related to the workpiece thickness, material strength, and die caliber. The Lorentz force distribution moves toward the region near the chamfer of the die, and the peak value of the Lorentz force and the deformation velocity of the workpiece are reduced by 62% and 26.9%, respectively, when considering workpiece pre-deformation. The resistance caused by residual air will obviously affect workpiece deformation. The influence will weaken as air pressure decreases, and the maximum deviation of the workpiece formed by a single discharge is less than 1.5% when the air pressure is reduced to 30 Pa.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Psyk V, Risch D, Kinsey BL, Tekkaya AE, Kleiner M (2011) Electromagnetic forming-a review. J Mater Process Technol 211:787–829. https://doi.org/10.1016/j.jmatprotec.2010.12.012
Correia JPM, Siddiqui MA, Ahzi S, Belouettar S, Davies R (2008) A simple model to simulate electromagnetic sheet free bulging process. Int J Mech Sci 50(10):1466–1475. https://doi.org/10.1016/j.ijmecsci.2008.08.008
Yu HP, Li CF (2009) Effects of current frequency on electromagnetic tube compression. J Mater Process Technol 209(2):1053–1059. https://doi.org/10.1016/j.jmatprotec.2008.03.011
Yu HP, Fan ZS, Li CF (2014) Magnetic pulse cladding of aluminum alloy on mild steel tube. J Mater Process Technol 214(2):141–150. https://doi.org/10.1016/j.jmatprotec.2013.08.013
Yu HP, Tong YC (2017) Magnetic pulse welding of aluminum to steel using uniform pressure electromagnetic actuator. Int J Adv Manuf Technol 91:2257–2265. https://doi.org/10.1007/s00170-016-9928-y
Takatsu N, Kato M, Sato K, Tobe T (1988) High-speed forming of metal sheets by electromagnetic force. JSME Int J 31(1):142–148. https://doi.org/10.1299/jsmec1988.31.142
Oliveira DA, Worswick MJ, Finn M, Newman D (2005) Electromagnetic forming of aluminum alloy sheet: free-form and cavity fill experiments and model. J Mater Process Technol 170(1):350–362. https://doi.org/10.1016/j.jmatprotec.2005.04.118
Kamal M, Daehn GS (2007) A uniform pressure electromagnetic actuator for forming flat sheets. J Manuf Sci Eng 129(2):369–379. https://doi.org/10.1115/1.2515481
Ahmed M, Panthi SK, Ramakrishnan N, Jha AK, Yegneswaran AH, Dasgupta R, Ahmed S (2011) Alternative flat coil design for electromagnetic forming using FEM. Trans Nonferrous Metals Soc China 21(3):618–625. https://doi.org/10.1016/S1003-6326(11)60759-0
Kleiner M, Beerwald C, Homberg W (2005) Analysis of process parameters and forming mechanisms within the electromagnetic forming process. CIRP Ann Manuf Technol 54(1):225–228. https://doi.org/10.1016/S0007-8506(07)60089-4
Shang JH, Daehn GS (2011) Electromagnetically assisted sheet metal stamping. J Mater Process Technol 211(5):868–874. https://doi.org/10.1016/j.jmatprotec.2010.03.005
Cui XH, Mo JH, Li JJ, Xiao XT, Zhou B, Fang JX (2016) Large-scale sheet deformation process by electromagnetic incremental forming combined with stretch forming. J Mater Process Technol 237:139–154. https://doi.org/10.1016/j.jmatprotec.2016.06.004
Lai ZP, Cao QL, Zhang B, Han XT, Zhou ZY, Xiong Q, Zhang X, Chen Q, Li L (2015) Radial Lorentz force augmented deep drawing for large drawing ratio using a novel dual-coil electromagnetic forming system. J Mater Process Technol 222:13–20. https://doi.org/10.1016/j.jmatprotec.2015.02.029
Lai ZP, Cao QL, Han XT, Huang YJ, Deng FX, Chen Q, Li L (2017) Investigation on plastic deformation behavior of sheet workpiece during radial Lorentz force augmented deep drawing process. J Mater Process Technol 245:193–206. https://doi.org/10.1016/j.jmatprotec.2017.02.010
Cui XH, Li JJ, Mo JH, Fang JX, Zhou B, Xiao XT (2016) Effect of the sheet thickness and current damping exponent on the optimum current frequency in electromagnetic forming. Int J Adv Manuf Technol 85(1–4):843–851. https://doi.org/10.1007/s00170-015-7983-4
Ma HJ, Huang L, Li JJ, Duan XC, Ma F (2018) Effects of process parameters on electromagnetic sheet free forming of aluminum alloy. Int J Adv Manuf Technol 96(1–4):359–369. https://doi.org/10.1007/s00170-018-1589-6
Cui XH, Mo JH, Li JJ, Zhao J, Zhu Y, Huang L, Li ZW, Zhong K (2014) Electromagnetic incremental forming (EMIF): a novel aluminum alloy sheet and tube forming technology. J Mater Process Technol 214(2):409–427. https://doi.org/10.1016/j.jmatprotec.2013.05.024
Lai ZP, Cao QL, Han XT, Liu N, Chen M, Li XX, Huang YJ, Chen Q, Li L (2018) Application of electromagnetic forming as a light-weight manufacturing method for large-scale sheet metal parts. In: Proceedings of the 8th International Conference on High Speed Forming-ICHSF, Ohio, American. doi:https://doi.org/10.17877/DE290R-18984
Cao QL, Han XT, Lai ZP, Xiong Q, Zhang X, Chen Q, Xiao HX, Li L (2015) Analysis and reduction of coil temperature rise in electromagnetic forming. J Mater Process Technol 225:185–194. https://doi.org/10.1016/j.jmatprotec.2015.02.006
Yu HP, Li CF, Deng JH (2009) Sequential coupling simulation for electromagnetic-mechanical tube compression by finite element analysis. J Mater Process Technol 209(2):707–713. https://doi.org/10.1016/j.jmatprotec.2008.02.061
Pierre LE, Iñaki C (2015). Recent developments in the electromagnetic module: a new 2D axi-symmetric EM solver. https://www.dynalook.com/10th-european-ls-dyna-conference/11%20Developer%20III%20-%20Multiphysics/03-LEplattenier-LSTC-P.pdf
Funding
This work was supported by the National Basic Research Program of China (973 Program): Grant No. 2011CB012801, the National Key Research and Development Program of China (Grant No. 2016YFA0401701), and the China Postdoctoral Science Foundation: 2018M632856.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Liu, N., Lai, Z., Cao, Q. et al. Effects of air on metallic sheet deformation by electromagnetic forming. Int J Adv Manuf Technol 103, 311–324 (2019). https://doi.org/10.1007/s00170-019-03479-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-019-03479-7