Abstract
Underfill defect in welding affects not only the surface integrity but also the mechanical properties of workpiece. In this paper, the effects of the process parameters on underfill defects were investigated, and the deep penetration welding by a 10-kW fiber laser on 12-mm-thick stainless steel plates was used as the case study. The correlation of the processing parameters with the formation and elimination of underfill defects was analyzed and discussed. It was found that during the autogenous laser welding of thick plates, the direction of laser beam relative to gravity has a significant effect on the formation of underfill defects, and the preferable direction was an inclination angle of 60° with respect to the gravity. A negative defocus tended to obtain a full penetration weld with underfill and undercut defects. The higher the welding speed was, the lower the underfill depth was on the top surface. This phenomenon was observed on the full penetration welds at a defocus of − 10 mm. With a negative defocus, it became feasible to optimize the combination of the focal position and the welding speed to achieve a satisfactory appearance of welds. In addition, a bottom-shielding ambience helped the full penetration in the laser welding process positively.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Bachmann M, Avilov V, Gumenyuk A, Rethmeier M (2014) Experimental and numerical investigation of an electromagnetic weld pool support system for high power laser beam welding of austenitic stainless steel. J Mater Process Technol 214(3):578–591. https://doi.org/10.1016/j.jmatprotec.2013.11.013
Zhang M, Chen G, Zhou Y, Liao S (2014) Optimization of deep penetration laser welding of thick stainless steel with a 10 kW fiber laser. Mater Des 53:568–576. https://doi.org/10.1016/j.matdes.2013.06.066
Sokolov M, Salminen A, Katayama S, Kawahito Y (2015) Reduced pressure laser welding of thick section structural steel. J Mater Process Technol 219:278–285. https://doi.org/10.1016/j.jmatprotec.2014.12.026
Guo W, Liu Q, Francis JA, Crowther D, Thompson A, Liu Z (2015) Comparison of laser welds in thick section S700 high-strength steel manufactured in flat (1G) and horizontal (2G) positions. CIRP Ann Manuf Technol 64(1):197–200. https://doi.org/10.1016/j.cirp.2015.04.070
Shen XF, Li L, Guo W, Teng WH, He WP (2016) Comparison of processing window and porosity distribution in laser welding of 10 mm thick 30CrMnSiA ultrahigh strength between flat (1G) and horizontal (2G) positions. J Laser Appl 28:1–9
Sun J, Feng K, Zhang K, Guo B, Jiang E, Nie P, Huang J, Li Z (2017) Fiber laser welding of thick AISI 304 plate in a horizontal (2G) butt joint configuration. Mater Des 118:53–65. https://doi.org/10.1016/j.matdes.2017.01.015
Chen Z, Gao X, Katayama S, Xiao Z, Chen X (2017) Elucidation of high-power disk laser welding phenomena by simultaneously observing both top and bottom of weldment. Int J Adv Manuf Tech 88(1–4):1141–1150. https://doi.org/10.1007/s00170-016-8837-4
Feng J, Guo W, Irvine N, Li L (2016) Understanding and elimination of process defects in narrow gap multi-pass fiber laser welding of ferritic steel sheets of 30 mm thickness. Int J Adv Manuf Technol 88(5–8):1821–1830
Zhang LJ, Bai QL, Ning J, Wang A, Yang NJ, Yin XQ, Zhang JX (2016) A comparative study on the microstructure and properties of copper joint between MIG welding and laser–MIG hybrid welding. Mater Des 10:35–50
Guo W, Crowther D, Francis JA, Thompson A, Liu Z, Li L (2015) Microstructure and mechanical properties of laser welded s960 high strength steel. Mater Des 85:534–548. https://doi.org/10.1016/j.matdes.2015.07.037
Zhan X, Wang Y, Liu Y, Zhang Q, Li Y, Wei Y (2015) Investigation on parameter optimization for laser welded butt joint of TA15 alloy. Int J Adv Manuf Technol 84(9–12):1–10
Yang J, Gang S, Li X, Chen L, Xu F (2010) Typical joint defects in laser welding of aluminium–lithium alloy. In: Proc of the 36th International MATADOR, London, pp 595–598
Matsumoto N, Kawahito Y, Nishimoto K, Katayama S (2017) Effects of laser focusing properties on weldability in high-power fiber laser welding of thick high-strength steel plate. J Laser Appl 29(1):012003 (9p). https://doi.org/10.2351/1.4966258
Li S, Chen G, Zhou C (2015) Effects of welding parameters on weld geometry during high-power laser welding of thick plate. Int J Adv Manuf Technol 79(1–4):177–182
Kashaev N, Ventzke V, Fomichev V, Fomin F, Riekehr S (2016) Effect of Nd: YAG laser beam welding on weld morphology and mechanical properties of Ti–6Al–4V butt joints and T-joints. Opt Lasers Eng 86:172–180
Fang XY, Liu H, Zhang JX (2015) Reducing the underfill rate of pulsed laser welding of titanium alloy through the application of a transversal pre-extrusion load. J Mater Process Technol 220:124–134
Fang XY, Zhang JX (2016) Microstructural evolution and mechanical properties in laser beam welds of Ti–2Al–1.5mn titanium alloy with transversal pre-extrusion load. Int J Adv Manuf Technol 85(1):337–343. https://doi.org/10.1007/s00170-015-7930-4
Zhang LJ, Zhang GF, Ning J, Zhang XJ, Zhang JX (2015) Microstructure and properties of the laser butt welded achieved at high welding speed. Mater Des 88:720–736. https://doi.org/10.1016/j.matdes.2015.09.072
Pan Q, Mizutani M, Kawahito Y, Katayama S (2016) High power disk laser–metal active gas arc hybrid welding of thick high tensile strength steel plates. J Laser Appl 28(1):012004. https://doi.org/10.2351/1.4934939
Kawahito Y, Mizutani M, Katayama S (2009) High quality welding of stainless steel with 10 kW high power fibre laser. Sci Technol Weld Join 14(4):288–294
Vänskä M, Abt F, Weber R, Salminen A, Graf T (2013) Effects of welding parameters onto keyhole geometry for partial penetration laser welding. Phys Procedia 41:199–208
Berger P, Hügel H, Graf T (2011) Understanding pore formation in laser beam welding. Phys Procedia 12:241–247
Jin X, Berger P, Graf T (2006) Multiple reflections and Fresnel absorption in an actual 3D keyhole during deep penetration laser welding. J Phys D Appl Phys 39(21):4703–4712
Zhang Y, Chen G, Wei H, Zhang J (2008) A novel 'sandwich' method for observation of the keyhole in deep penetration laser welding. Opt Laser Eng 46(2):133–139. https://doi.org/10.1016/j.optlaseng.2007.08.010
Zhang M, Chen G, Zhou Y, Li S (2013) Direct observation of keyhole characteristics in deep penetration laser welding with a 10 kW fiber laser. Opt Express 21(17):19997–20004. https://doi.org/10.1364/OE.21.019997
Zou JL, Wu SK, He Y, Yang WX, Xu JJ, Xiao RS (2015) Distinct morphology of the keyhole wall during high-power fiber laser deep penetration welding. Sci Technol Weld Join 20(8):655–658. https://doi.org/10.1179/1362171815Y.0000000049
Zou JL, Wu SK, Yang WX, He Y, Xu JJ, Xiao RS (2016) A novel method for observing the micro-morphology of keyhole wall during high-power fiber laser welding. Mater Des 89:785–790. https://doi.org/10.1016/j.matdes.2015.10.039
Kaplan AF (2012) Local absorptivity modulation of a 1 μm-laser beam through surface waviness. Appl Surf Sci 258(24):9732–9736. https://doi.org/10.1016/j.apsusc.2012.06.020
Kuryntsev SV, Gilmutdinov AK (2015) Heat treatment of welded joints of steel 0.3С–1Cr–1 Si produced by high-power fiber lasers. Opt Laser Technol 74:125–131. https://doi.org/10.1016/j.optlastec.2015.06.004
Zhang MJ, Chen GY, Zhou Y, Li SC, Deng H (2013) Observation of spatter formation mechanisms in high-power fiber laser welding of thick plate. Appl Surf Sci 280:868–875. https://doi.org/10.1016/j.apsusc.2013.05.081
Ilar T, Eriksson I, Powell J, Kaplan AFH (2012) Root humping in laser welding—an investigation based on high speed imaging. In: Laser Assisted Net Shape Engineering 7 (LANE 2012), Furth, Physics Procedia, vol 39. Elsevier, pp 27–32
Mei LF, Yan DB, Yi JM, Chen GY, Ge XH (2013) Comparative analysis on overlap welding properties of fiber laser and CO2 laser for body-in-white sheets. Mater Des 49:905–912. https://doi.org/10.1016/j.matdes.2013.02.003
Vänskä M, Abt F, Weber R, Salmine A, Graf T (2013) Effects of welding parameters onto keyhole geometry for partial penetration laser welding. In: Lasers in Manufacturing (LiM 2013), Munich, Physics Procedia, vol 41. Elsevier, pp 199–208
Cheng Y, Jin X, Li S, Zeng L (2012) Fresnel absorption and inverse bremsstrahlung absorption in an actual 3D keyhole during deep penetration CO2 laser welding of aluminum 6016. Opt Laser Technol 44(5):1426–1436. https://doi.org/10.1016/j.optlastec.2011.12.024
Rai R, Palmer TA, Elmer JW, Debroy T (2009) Heat transfer and fluid flow during electron beam welding of 304l stainless steel alloy. Weld J 88(3):54s–61s
Fabbro R (2010) Melt pool and keyhole behaviour analysis for deep penetration laser welding. J Phys D Appl Phys 43(44):445501 (9pp)
Pang S, Chen X, Shao X, Gong S, Xiao J (2016) Dynamics of vapor plume in transient keyhole during laser welding of stainless steel: local evaporation, plume swing and gas entrapment into porosity. Opt Lasers Eng 82:28–40
Eriksson I, Powell J, Kaplan AFH (2011) Measurements of fluid flow on keyhole front during laser welding. Sci Technol Weld Join 16:636–641
Tan W, Shin Y (2014) Analysis of multi-phase interaction and its effects on keyhole dynamics with a multi-physics numerical model. J Phys D Appl Phys 47(34):345501 (17p). https://doi.org/10.1088/0022-3727/47/34/345501
Pang S, Chen X, Li W, Shao X, Gong S (2016) Efficient multiple time scale method for modeling compressible vapor plume dynamics inside transient keyhole during fiber laser welding. Opt Laser Technol 77:203–214
Acknowledgments
The authors thank Prof. Zhuming Bi from Purdue University Fort Wayne for polishing the English.
Funding
The authors are grateful to the financial support from the National Natural Science Foundation of China (No. 51605045, 51405034, 51641502), and the Natural Science Foundation of Hunan Province of China (No. 2015JJ3003).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zhang, M., Tang, K., Zhang, J. et al. Effects of processing parameters on underfill defects in deep penetration laser welding of thick plates. Int J Adv Manuf Technol 96, 491–501 (2018). https://doi.org/10.1007/s00170-018-1613-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-1613-x