Abstract
The flaring of a thin-walled tube is conventionally carried out by pressing the tube end using dedicated die sets. As an alternative process with the high flexibility and low complexity, in this research, the utilization of single point incremental forming (SPIF), which is the simplest variant of incremental sheet metal forming (ISMF) processes, was assessed and investigated experimentally and numerically for flaring of the tube end. Results predicted by the finite element (FE) model through the commercial code Abaqus/Explicit showed a reasonable agreement with the experimental results. In the present research, the formability in SPIF was compared with that in pressing process and it was concluded that using multistage SPIF, the maximum semi-cone angle achievable before fracture can be improved at least 100%. The results showed that the thickness distribution in the conical flaring of the tube end includes thinning and thickening regions affected by the deformation strategy of multistage SPIF. In this regard, the formability of the tube end and the material deformation were studied under various forming strategies. Finally, for non-axisymmetric flaring of the tube end in the form of a pyramid with the semi-angle of 20° using SPIF, different three-stage forming strategies were designed and successfully implemented. The thickness distribution and the geometric accuracy under designed three-stage strategies were investigated.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Huang Y-M (2004) Finite element analysis of tube flaring process with a conical tool. Int J Adv Manuf Technol 24(1):91–97. https://doi.org/10.1007/s00170-003-1704-0
Lu Y-H (2004) Study of tube flaring ratio and strain rate in the tube flaring process. Finite Elem Anal Des 40(3):305–318. https://doi.org/10.1016/S0168-874X(03)00049-0
Almeida BPP, Alves ML, Rosa PAR, Brito AG, Martins PAF (2006) Expansion and reduction of thin-walled tubes using a die: experimental and theoretical investigation. Int J Mach Tools Manuf 46(12–13):1643–1652. https://doi.org/10.1016/j.ijmachtools.2005.08.018
Huang YM (2009) Flaring and nosing process for composite annoy tube in circular cone tool application. Int J Adv Manuf Technol 43(11):1167–1176. https://doi.org/10.1007/s00170-008-1795-8
Nikhare CP, Korkolis YP, Kinsey BL (2015) Formability enhancement in titanium tube-flaring by manipulating the deformation path. J Manuf Sci Eng 137(5):051006–051006. https://doi.org/10.1115/1.4030512
Zhao X, Xu W, Chen Y, Ma H, Shan D, Lin H (2016) Fabrication of curved generatrix workpiece of TA15 titanium alloy by variable thickness tube spinning and flaring process. Int J Adv Manuf Technol 88:1–10. https://doi.org/10.1007/s00170-016-8917-5
Jackson KP, Allwood JM, Landert M (2008) Incremental forming of sandwich panels. J Mater Process Technol 204(1–3):290–303. https://doi.org/10.1016/j.jmatprotec.2007.11.117
Shim M-S, Park J-J (2001) The formability of aluminum sheet in incremental forming. J Mater Process Technol 113(1–3):654–658. https://doi.org/10.1016/S0924-0136(01)00679-3
Hussain G, Gao L (2007) A novel method to test the thinning limits of sheet metals in negative incremental forming. Int J Mach Tools Manuf 47(3–4):419–435. https://doi.org/10.1016/j.ijmachtools.2006.06.015
Jackson K, Allwood J (2009) The mechanics of incremental sheet forming. J Mater Process Technol 209(3):1158–1174. https://doi.org/10.1016/j.jmatprotec.2008.03.025
Manco GL, Ambrogio G (2010) Influence of thickness on formability in 6082-T6. Int J Mater Form 3(1):983–986. https://doi.org/10.1007/s12289-010-0934-6
Hamilton K, Jeswiet J (2010) Single point incremental forming at high feed rates and rotational speeds: surface and structural consequences. CIRP Ann Manuf Technol 59(1):311–314. https://doi.org/10.1016/j.cirp.2010.03.016
Mirnia MJ, Mollaei Dariani B, Vanhove H, Duflou JR (2014) An investigation into thickness distribution in single point incremental forming using sequential limit analysis. Int J Mater Form 7(4):469–477. https://doi.org/10.1007/s12289-013-1143-x
Mirnia MJ, Mollaei Dariani B, Vanhove H, Duflou JR (2014) Thickness improvement in single point incremental forming deduced by sequential limit analysis. Int J Adv Manuf Technol 70(9):2029–2041. https://doi.org/10.1007/s00170-013-5447-2
Kurra S, Hifzur Rahman N, Regalla SP, Gupta AK (2015) Modeling and optimization of surface roughness in single point incremental forming process. J Mater Res Technol 4(3):304–313. https://doi.org/10.1016/j.jmrt.2015.01.003
Teramae T, Manabe K, Ueno K, Nakamura K, Takeda H (2007) Effect of material properties on deformation behavior in incremental tube-burring process using a bar tool. J Mater Process Technol 191(1–3):24–29. https://doi.org/10.1016/j.jmatprotec.2007.03.039
Yang C, Wen T, Liu LT, Zhang S, Wang H (2014) Dieless incremental hole-flanging of thin-walled tube for producing branched tubing. J Mater Process Technol 214(11):2461–2467. https://doi.org/10.1016/j.jmatprotec.2014.05.027
Wen T, Yang C, Zhang S, Liu L (2015) Characterization of deformation behavior of thin-walled tubes during incremental forming: a study with selected examples. Int J Adv Manuf Technol 78(9):1769–1780. https://doi.org/10.1007/s00170-014-6777-4
Raujol-Veillé J, Toussaint F, Tabourot L, Vautrot M, Balland P (2015) Experimental and numerical investigation of a short, thin-walled steel tube incremental forming process. J Manuf Process 19:59–66. https://doi.org/10.1016/j.jmapro.2015.03.008
Zhang MH, Lu B, Chen J, Long H, Ou H (2015) Selective element fission approach for fast FEM simulation of incremental sheet forming based on dual-mesh system. Int J Adv Manuf Technol 78(5):1147–1160. https://doi.org/10.1007/s00170-014-6723-5
Emmens WC, van den Boogaard AH (2009) An overview of stabilizing deformation mechanisms in incremental sheet forming. J Mater Process Technol 209(8):3688–3695. doi:https://doi.org/10.1016/j.jmatprotec.2008.10.003
Mirnia MJ, Shamsari M (2017) Numerical prediction of failure in single point incremental forming using a phenomenological ductile fracture criterion. J Mater Process Technol 244:17–43. https://doi.org/10.1016/j.jmatprotec.2017.01.029
Benzerga AA, Surovik D, Keralavarma SM (2012) On the path-dependence of the fracture locus in ductile materials—analysis. Int J Plast 37:157–170. doi:https://doi.org/10.1016/j.ijplas.2012.05.003
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no conflict of interest.
Rights and permissions
About this article
Cite this article
Movahedinia, H., Mirnia, M.J., Elyasi, M. et al. An investigation on flaring process of thin-walled tubes using multistage single point incremental forming. Int J Adv Manuf Technol 94, 867–880 (2018). https://doi.org/10.1007/s00170-017-0971-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-0971-0