Abstract
This study focuses on chip–tool interface temperature modeling of C-60, 17CrNiMo4, and 42CrMo4 steel alloys in dry-cut and high-pressure coolant (HPC)-assisted turning at various cutting speed-feed rates with SNMG and SNMM inserts. Improvement of tool life in turning C-60 steel under the application of jet at elevated pressure over dry machining is investigated. Scanning electron microscope (SEM) views of principal and auxiliary flank worn out tip (48-min) of cutting inserts divulge the effectiveness of high-pressure coolant emulsion over dry and conventional wet cooling. The experimental runs were conducted in full factorial orientation and response surface methodology (RSM) has been employed for subsequent modeling to formulate mathematical equations to devise accurate predictions of chip–tool interface temperature. Analysis of variance (ANOVA) is conducted to perceive the effects of each individual factors and their interactions terms and measure the significance of the proposed model. Later, optimization with desirability function concluded factor settings (cutting speed = 93 m/min, feed rate = 0.10 mm/rev, environment = HPC, material = C-60, and insert = SNMM) that minimize the response within the experimental domain satisfying desired goals. Further, artificial neural network (ANN) model has been developed and the prediction performance was compared with the cubic equations of RSM. It was observed that during testing phase MAPE and coefficient of determination (R 2) for RSM is 1.947 and 94.48 %, respectively; and the corresponding values for ANN (4-22-1) is 2.669 and 93.25 %. Results also reveal that cutting speed and environment have ∼38.82 and ∼37.82 % contribution on chip–tool interface temperature formation during machining. In addition, the results showed that HPC-assisted machining reduces chip–tool interface temperature significantly as well as prolong tool life.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Dhar N, Kamruzzaman M (2007) Cutting temperature, tool wear, surface roughness and dimensional deviation in turning AISI-4037 steel under cryogenic condition. Int J Mach Tools Manuf 47(5):754–759
Kamruzzaman M, Dhar N (2008) The effect of applying high-pressure coolant (HPC) jet in machining of 42CrMo4 steel by uncoated carbide inserts. J Mech Eng 39(2):71–77
Çakıroğlu R, Acır A (2013) Optimization of cutting parameters on drill bit temperature in drilling by Taguchi method. Measurement 46(9):3525–3531
Sun S, Brandt M, Palanisamy S, Dargusch MS (2015) Effect of cryogenic compressed air on the evolution of cutting force and tool wear during machining of Ti–6Al–4V alloy. J Mater Process Technol 221:243–254
Sales WF, Diniz AE, Machado ÁR (2001) Application of cutting fluids in machining processes. J Braz Soc Mech Sci 23(2):227–240
Wertheim R, Rotberg J, Ber A (1992) Influence of high-pressure flushing through the rake face of the cutting tool. CIRP Ann-Manuf Technol 41(1):101–106
Raynor PC, Cooper S, Leith D (1996) Evaporation of polydisperse multicomponent oil droplets. Am Ind Hyg Assoc J 57(12):1128–1136
Umbrello D, Micari F, Jawahir I (2012) The effects of cryogenic cooling on surface integrity in hard machining: a comparison with dry machining. CIRP Ann-Manuf Technol 61(1):103–106
Islam AK, Mia M, Dhar NR (2016) Effects of internal cooling by cryogenic on the machinability of hardened steel. Int J Adv Manuf Technol:1–10. doi:10.1007/s00170-016-9373-y
Dhar N, Islam M, Islam S, Mithu M (2006) The influence of minimum quantity of lubrication (MQL) on cutting temperature, chip and dimensional accuracy in turning AISI-1040 steel. J Mater Process Technol 171(1):93–99
Amini S, Paktinat H (2014) Ceramic tools with ordinary and wiper inserts in near dry machining with high speed on super alloy Monel K500. Mater Manuf Process 29(5):579–584
Mia M, Dhar NR (2016) Optimization of surface roughness and cutting temperature in high-pressure coolant-assisted hard turning using Taguchi method. Int J Adv Manuf Technol:1–15. doi:10.1007/s00170-016-8810-2
Sharman A, Hughes J, Ridgway K (2008) Surface integrity and tool life when turning Inconel 718 using ultra-high pressure and flood coolant systems. Proc Inst Mech Eng B J Eng Manuf 222(6):653–664
Bermingham M, Palanisamy S, Kent D, Dargusch M (2012) A comparison of cryogenic and high pressure emulsion cooling technologies on tool life and chip morphology in Ti–6Al–4V cutting. J Mater Process Technol 212(4):752–765
Ezugwu E (2005) Key improvements in the machining of difficult-to-cut aerospace superalloys. Int J Mach Tools Manuf 45(12):1353–1367
Wright P, Horne J, Tabor D (1979) Boundary conditions at the chip-tool interface in machining: comparisons between seizure and sliding friction. Wear 54(2):371–390
Ezugwu E, Da Silva R, Bonney J, Machado A (2005) Evaluation of the performance of CBN tools when turning Ti–6Al–4V alloy with high pressure coolant supplies. Int J Mach Tools Manuf 45(9):1009–1014
Braham-Bouchnak T, Germain G, Morel A, Furet B (2015) Influence of high-pressure coolant assistance on the machinability of the titanium alloy Ti555-3. Mach Sci Technol 19(1):134–151
Naves V, Da Silva M, Da Silva F (2013) Evaluation of the effect of application of cutting fluid at high pressure on tool wear during turning operation of AISI 316 austenitic stainless steel. Wear 302(1):1201–1208
Karkalos N, Galanis N, Markopoulos A (2016) Surface roughness prediction for the milling of Ti–6Al–4V ELI alloy with the use of statistical and soft computing techniques. Measurement 90:25–35
Bouzid L, Yallese MA, Chaoui K, Mabrouki T, Boulanouar L (2015) Mathematical modeling for turning on AISI 420 stainless steel using surface response methodology. Proc Inst Mech Eng B J Eng Manuf 229(1):45–61
Rajmohan T, Sathishkumar S, Palanikumar K, Ranganathan S (2015) Modeling and analysis of cutting force in turning of AISI 316L Stainless Steel (SS) under nano cutting environment. Appl Mech Mater
Berkani S, Bouzid L, Bensouilah H, Yallese MA, Girardin F, Mabrouki T (2015) Modeling and optimization of tool wear and surface roughness in turning of austenitic stainless steel using response surface methodology. S09d Procédés d’usinage
Nayak M, Sehgal R (2015) Effect of tool material properties and cutting conditions on machinability of AISI D6 steel during hard turning. Arab J Sci Eng 40(4):1151–1164
Gosai M, Bhavsar SN (2016) Experimental study on temperature measurement in turning operation of hardened steel (EN36. Procedia Technol 23:311–318
Abhang L, Hameedullah M (2010) Chip-tool interface temperature prediction model for turning process. Int J Eng Sci Technol 2(4):382–393
Sharma MD, Sehgal R (2015) Modelling of machining process while turning tool steel with CBN tool. Arab J Sci Eng:1–22
Çalışkan H, Kurbanoğlu C, Panjan P, Kramar D (2013) Investigation of the performance of carbide cutting tools with hard coatings in hard milling based on the response surface methodology. Int J Adv Manuf Technol 66(5–8):883–893
Amini S, Fatemi M, Atefi R (2014) High speed turning of Inconel 718 using ceramic and carbide cutting tools. Arab J Sci Eng 39(3):2323–2330
Özel T, Karpat Y (2005) Predictive modeling of surface roughness and tool wear in hard turning using regression and neural networks. Int J Mach Tools Manuf 45(4):467–479
Rao KV, Murthy B, Rao NM (2014) Prediction of cutting tool wear, surface roughness and vibration of work piece in boring of AISI 316 steel with artificial neural network. Measurement 51:63–70
Kumar R, Chauhan S (2015) Study on surface roughness measurement for turning of Al 7075/10/SiCp and Al 7075 hybrid composites by using response surface methodology (RSM) and artificial neural networking (ANN. Measurement 65:166–180
Jayakumar K, Mathew J, Joseph M (2013) An investigation of cutting force and tool–work interface temperature in milling of Al–SiCp metal matrix composite. Proc Inst Mech Eng B J Eng Manuf 227(3):362–374
Adesta EYT, Al Hazza MH, Suprianto M, Riza M (2012) Prediction of cutting temperatures by using back propagation neural network modeling when cutting hardened H-13 steel in CNC end milling. In: Advanced Materials Research. Trans Tech Publ:91–94
Tanikic D, Manic M, Devedzic G, Cojbasic Z (2010) Modelling of the temperature in the chip-forming zone using artificial intelligence techniques. Neural Network World 20(2):171
Kara F, Aslantaş K, Çiçek A (2016) Prediction of cutting temperature in orthogonal machining of AISI 316L using artificial neural network. Appl Soft Comput 38:64–74
Korkut I, Acır A, Boy M (2011) Application of regression and artificial neural network analysis in modelling of tool–chip interface temperature in machining. Expert Syst Appl 38(9):11651–11656
DeChiffre L (1981) Lubrication in cutting—critical review and experiments with restricted contact tools. Asle. Transactions 24(3):340–344
Debnath S, Reddy MM, Yi QS (2014) Environmental friendly cutting fluids and cooling techniques in machining: a review. J Clean Prod 83:33–47
Allen DM (1974) The relationship between variable selection and data agumentation and a method for prediction. Technometrics 16(1):125–127
Saglam H, Yaldiz S, Unsacar F (2007) The effect of tool geometry and cutting speed on main cutting force and tool tip temperature. Mater Des 28(1):101–111
Myers RH, Montgomery DC, Anderson-Cook CM (2016) Response surface methodology: process and product optimization using designed experiments. John Wiley & Sons, New York
Box GE, Draper NR (1987) Empirical model-building and response surfaces, vol 424. Wiley, New York
Kamruzzaman M, Dhar N (2009) The influence of high pressure coolant on temperature tool wear and surface finish in turning 17CrNiMo6 and 42CrMo4 steels. J Eng Appl Sci 4(6):93–103
Mia M, Khan MA, Rahman SS, Dhar NR (2016) Mono-objective and multi-objective optimization of performance parameters in high pressure coolant assisted turning of Ti-6Al-4V. Int J Adv Manuf Technol:1–10. doi:10.1007/s00170-016-9372-z
Hornik K, Stinchcombe M, White H (1989) Multilayer feedforward networks are universal approximators. Neural Netw 2(5):359–366
Beale MH, Hagan MT, Demuth HB (2010) Neural network toolbox 7. User’s Guide, MathWorks
Mia M, Dhar NR (2016) Prediction of surface roughness in hard turning under high pressure coolant using artificial neural network. Measurement 92:464–474
MacKay DJ (1992) A practical Bayesian framework for backpropagation networks. Neural Comput 4(3):448–472
Foresee FD, Hagan MT (1997) Gauss-Newton approximation to Bayesian learning. In: Neural Networks, 1997, International Conference on. IEEE:1930–1935
Haykin SS, Haykin SS, Haykin SS, Haykin SS (2009) Neural networks and learning machines, vol 3. Pearson Education Upper Saddle River
Mia M, Dhar NR (2016) Response surface and neural network based predictive models of cutting temperature in hard turning. J Adv Res
Groover MP (2012) Fundamentals of modern manufacturing: materials, processes, and systems, 5th edn. Wiley Global Education
Trent EM, Wright PK (2000) Metal cutting. Butterworth-Heinemann
Kamruzzaman M, Dhar N Performance evaluation of carbide inserts in turning C-60 steel and 42crmo4 steel under high-pressure coolant (Hpc) condition
da Silva RB, Machado ÁR, Ezugwu EO, Bonney J, Sales WF (2013) Tool life and wear mechanisms in high speed machining of Ti–6Al–4V alloy with PCD tools under various coolant pressures. J Mater Process Technol 213(8):1459–1464
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Kamruzzaman, M., Rahman, S.S., Ashraf, M.Z.I. et al. Modeling of chip–tool interface temperature using response surface methodology and artificial neural network in HPC-assisted turning and tool life investigation. Int J Adv Manuf Technol 90, 1547–1568 (2017). https://doi.org/10.1007/s00170-016-9467-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-9467-6