Abstract
The main objective of this paper is to develop the relationship between microstructure and machinability of titanium alloy Ti-6Al-4V which is given heat treatment beyond β transus temperature, with the help of milling experiments using polycrystalline diamond (PCD) tools. Two of the specimens were solution treated at 1050 °C/1 h. After the treatment, one of the specimen was cooled in water while the other specimen was air-cooled, followed by aging treatment at 550 °C/4 h. The third specimen was used in as-received condition (casted). Cutting speed, feed rate, and depth of cut were varied, and their effects have been analyzed on cutting forces, vibration amplitude, temperature, and tool wear for all the three specimens. The results have shown improved and better machinability for the specimen which was cooled in air after the solution treatment with PCD tools. This behavior of the alloy is mainly attributed to formation of homogeneous lamellar α + β Ti-6Al-4V microstructure. Although, the air-cooled specimen has higher hardness than the as-received specimen. But, the former alloy’s fine homogeneous and lamellar α + β Ti-6Al-4V microstructure as compared to the microstructure of the latter specimen (irregular α + β Ti-6Al-4V structure) and absence of α’ secondary precipitate (found in water-cooled specimen) has helped in giving improved performance. Thus, from this study, it can be concluded that machinability of titanium alloy Ti-6Al-4V can be further improved with controlled heat treatment process using PCD tools.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Armendia M, Garay A, Iriarte L-M, Arrazola P-J (2010) Comparison of the machinabilities of Ti6Al4V and TIMETAL® 54M using uncoated WC–Co tools. J Mater Process Technol 210(2):197–203
Rahman M, Wong YS, Zareena AR (2003) Machinability of titanium alloys. JSME Int J Ser C 46:17–115
Ezugwu EO, Bonney J, Yamane Y (2003) An overview of the machinability of aero engine alloys. J Mater Process Technol 133:233–253
Li L, Chang H, Wang M, Zuo DW, He L (2004) Temperature measurement in high speed milling Ti6Al4V. Key Eng Mater. 259–260: 804–808
Jawaid A, Sharif S, Koksal S (2000) Evaluation of wear mechanisms of coated carbide tools when face milling. J Mater Process Technol 99:266–274
Wang ZG, Rahman M, Wang YS (2005) Tool wear characteristics of binderless CBN tools used in high speed milling of titanium alloys. Wear 258:752–758
Kuljanic E, Fioretti M, Beltrame L, Miani F (1998) Milling titanium compressor blades with PCD cutters. CIRP Ann Manuf Technol 47(1):61–64
Nabhani F (2001) Machining of aerospace titanium alloys. Robot Comput Integr Manuf 17(1–2):99–106
Amin AKMN, Ismail Ahmad F, Khairusshima MK (2007) Nor, effectiveness of un-coated WC-Co and PCD inserts in end milling of titanium alloy – Ti6Al4V. J Mater Process Technol. 192–193: 147–158
Pan W, Ding S, Mo J (2014) Thermal characteristics in milling Ti6Al4V with polycrystalline diamonds tools. Int J Adv Manuf Technol 75:1077–1087
Ezugwu EO, Bonney J, Rosemar B, Silva D, Cakir O (2007) Surface integrity of finished turned Ti-6Al-4V alloy with PCD tools using conventional and higher pressure coolant supplies. Int J Mach Tool Manuf 47:884–891
Konig W, Neises N (1993) Turning TiAl6V4 with PCD. Ind Diamond Rev 53(1):85–88
Honghua SU, Peng L, Yucan FU, Jiuhua XU (2012) Tool life and surface integrity in high-speed milling of titanium alloy TA15 with PCD/PCBN tools. Chin J Aeronaut 25:784–790
Kosaka Y, Fox SP (2004) Influence of alloy chemistry and microstructure on the machinability of titanium alloys. In Proceedings of Cost Affordable Titanium TMS Conference, 169–176
Kosaka Y, Fanning JC, Fox SP (2004) Development of low cost high strength alpha/beta alloys with superior machinability. In Proceedings of 10th world conference on titanium. 3028–3034
Khanna N, Garay A, Iriarte LM, Soler D, Sangwan KS, Pedro J (2012) Arrazola, effect of heat treatment conditions on machinability of Ti64 and Ti54M alloys. In Proceedings of 5th CIRP Conference on High Performance Cutting, Procedia CIRP 1: 477–482
Khanna N, Sangwan KS (2013) Machinability study of α/β and β titanium alloys in different heat treatment conditions. Proc IMechE Part B: J Eng Manuf 227(3):357–361
Rahim EA, Sharif S (2006) Investigation on tool life and surface integrity when drilling Ti-6Al-4V and Ti-5Al-4V-Mo/Fe. J Soc Mech Eng Int J 49:340–345
Venkatesh V, Kosaka Y, Fanning J, Nyakana S (2007) Processing and properties of Timetal 54M. In Proceedings of 11th world conference on Titanium, Kyoto, Japan, 713–716
Armendia M, Garay A, Iriarte LM, Belloso J, Turner SM, Osborne P, Arrazola PJ (2010) The influence of heat treatment in the machinability of titanium alloys: Ti6Al4V and Ti-5Al-4V-0.6Mo-0.4Fe (Ti54M). In Proceedings of 4th CIRP International Conference on High Performance Cutting, Japan, C02
Azam M, Jahanzaib M, Wasim A, Hussain S (2015) Surface roughness modeling using RSM for HSLA steel by coated carbide tools. Int J Adv Manuf Technol 78:1031–1041
Pinke P, Žitňanský, Čaplovič L’, Réger M (2004) The influence of heat treatment parameters on the microstructure of Ti6Al4V titanium alloy. In Proceedings of International Scientific Conference CO-MAT-TECH, Bratisalva: Vydavatel, STU. 1042–1046
Anayet UPM, Amin AKMN, Faris WF (2009) Prediction of tangential cutting force in end milling of medium carbon steel by coupling design of experiments and response surface methodology. J Mech Eng 40:2
Amin AKMN, Talantov NV (1986) Influence of the instability of chip formation and preheating of work on tool life in machining high temperature resistant steel and titanium alloys. Mech Eng Residuals Bull 9:52–62
Komanduri R, Hou ZB (2002) On the thermoplastic shear instability in the machining of a titanium alloy (Ti-6Al-4V). Metall Mater Trans A 33:2995–3010
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Abbasi, S.A., Feng, P., Ma, Y. et al. Influence of microstructure and hardness on machinability of heat-treated titanium alloy Ti-6Al-4V in end milling with polycrystalline diamond tools. Int J Adv Manuf Technol 86, 1393–1405 (2016). https://doi.org/10.1007/s00170-015-8245-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-8245-1