Abstract
Minimum quantity lubrication (MQL) has been proposed as a promising alternative to conventional flood cooling to substantially reduce the lubrication usage while maintaining high surface quality. Residual stress induced by grinding process directly affects the surface quality of the final product. An analytical relationship between residual stresses and process conditions such as process parameters, material properties, and lubrication conditions could support process planning and optimization of MQL grinding. This paper has presented a physics-based model to predict residual stresses in grinding with consideration of the lubrication and cooling effects of MQL. Grinding force and temperature distribution in the workpiece are used to calculate the loading stresses imparted by MQL grinding. The loading stresses are then coupled into a rolling/sliding contact algorithm to solve for residual stresses. Experimental measurements of residual stress profile under and flood cooling conditions have been pursued to calibrate and validate the predicted results.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Autret R, Liang S (2003) Minimum quantity lubrication in finish hard turning. Proceedings of International Conference on Humanoid, Nanotechnology, Information Technology, Communication and Control, Environment, and Management, Manila
Kruszynski B, Wojcik R (2001) Residual stress in grinding. J Mater Process Technol 109(3):254–257. doi:10.1016/S0924-0136(00)00807-4
Mahdi M, Zhang L (1999) Applied mechanics in grinding. Part 7: residual stresses induced by the full coupling of mechanical deformation, thermal deformation and phase transformation. Int J Mach Tools Manuf 39(8):1285–1298. doi:10.1016/S0890-6955(98)00094-7
Chen X, Rowe W, McCormack D (2000) Analysis of the transitional temperature for tensile residual stress in grinding. J Mater Process Technol 107(1–3):216–221. doi:10.1016/S0924-0136(00)00692-0
Fergani O, Shao Y, Lazoglu I, Liang S (2014) Temperature effects on grinding residual stress. Procedia CIRP 14:2–6. doi:10.1016/j.procir.2014.03.100
Ji X, Zhang X, Li B, Liang S (2014) Modeling of the effects of minimum quantity lubrication on machining force, temperature, and residual stress. Mach Sci Technol 18(4):547–564. doi:10.1080/10910344.2014.955367
Tai B, Stephenson D, Shih A (2013) Workpiece temperature during deep-hole drilling of cast iron using high air pressure minimum quantity lubrication. J Manuf Sci Eng 135(3):1–7. doi:10.1115/1.4024036
Silva L, Bianchi E, Fusse R, Catai R, Franca T, Aguiar P (2007) Analysis of surface integrity for minimum quantity lubricant—MQL grinding. Int J Mach Tools Manuf 47(2):412–418. doi:10.1016/j.ijmachtools.2006.03.015
Shen B, Shih A, Tung S (2008) Application of nanofluids in minimum quantity lubrication grinding. Tribol Trans 51(6):730–737. doi:10.1080/10402000802071277
Tawakoli T, Hadad M, Sadeghi M, Daneshi A, Stockert S, Rasifard A (2009) An experimental investigation of the effects of workpiece and grinding parameters on minimum quantity lubrication—MQL grinding. Int J Mach Tools Manuf 49(12–13):924–932. doi:10.1016/j.ijmachtools.2009.06.015
Shao Y, Fergani O, Ding Z, Li B, Liang S (2015) Experimental investigation of residual stress in minimum quantity lubrication grinding of AISI 1018 steel. J Manuf Sci Eng. doi:10.1115/1.4029956
Hadad M, Sadeghi B (2012) Thermal analysis of minimum quantity lubrication—MQL grinding process. Int J Mach Tools Manuf 63:1–15. doi:10.1016/j.ijmachtools.2012.07.003
Shao Y, Liang S (2014) Predictive force modeling in MQL (minimum quantity lubrication) grinding. Proceedings of the ASME 2014 International Manufacturing Science and Engineering Conference, Detroit. doi:10.1115/MSEC2014-3971
Shao Y, Li B, Chiang K, Liang S (2015) Physics-based analysis of minimum quantity lubrication grinding. Int J Adv Manuf Technol. doi:10.1007/s00170-015-6941-5
McDowell D (1997) Approximate algorithm for elastic–plastic two-dimensional rolling/sliding contact. Wear 211(2):237–246. doi:10.1016/S0043-1648(97)00117-8
Kato S, Marui E, Hashimoto M (1998) Fundamental study on normal load dependency of friction characteristics in boundary lubrication. Tribol Trans 41(3):341–349. doi:10.1080/10402009808983757
Ding Z, Li B, Zou P, Liang S (2014) Material phase transformation during grinding. Adv Mater Res 1052:503–508. doi:10.4028/www.scientific.net/AMR.1052.503
Timoshenko S, Goodier J (1970) Theory of elasticity, Internationalth edn. McGraw-Hill, Singapore
Saif M, Hui C, Zehnder A (1993) Interface shear stresses induced by non-uniform heating of a film on a substrate. Thin Solid Films 224(2):159–167. doi:10.1016/00406090(93)90427-Q
List G, Stter G, Bouthiche A (2012) Cutting temperature prediction in high speed machining by numerical modelling of chip formation and its dependence with crater wear. Int J Mach Tools Manuf 54–55:1–9. doi:10.1016/j.ijmachtools.2011.11.009
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Shao, Y., Fergani, O., Li, B. et al. Residual stress modeling in minimum quantity lubrication grinding. Int J Adv Manuf Technol 83, 743–751 (2016). https://doi.org/10.1007/s00170-015-7527-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-7527-y