Abstract
Wire electro-discharges machining (WEDM) is a variant of electro-discharge machining (EDM) based method for non-contact machining that uses wire as the machining tool. Micro-EDMing/micro-WEDMing (where discharge energy is very low and tool size in micrometer range) operation of silicon (Si) can achieve features with very complex shapes, which have many useful applications in microelectro-mechanical system (MEMS). However, Si is a semiconductor material with high resistivity, and it is difficult to create electrical sparks during μ-WEDM/μ-EDM process. Thus, the machining of Si can be enhanced if it is possible to increase the conductivity of this semiconductor. This study aims to develop and characterize the process of improved μ-WEDM and μ-EDM of Si by temporarily coating Si with a high conductive metal (gold in this study). Micro-WEDM process stability was found to be improved (~100× for different machining condition) if coated Si wafer is used as compared to uncoated Si workpiece. Material removal rate (MRR) was also found to be increased by a good margin (~30 % average) for coated Si wafer. Machined slots were found to be more uniform though kerf width was slightly larger for coated Si wafer. In case of μ-EDM operation, gold-coated Si also enhanced the machining as compared to uncoated Si. In this case, MRR was increased by up to seven times for coated samples. Overall, this new method of μ-WEDM and μ-EDM technique of polished Si wafer has been found to be more efficient and useful. Removal of the conductive coating without damaging the substrate is a challenge for this process, which was carried out successfully by selective etching method.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Ho KH, Newman ST (2003) State of the art electrical discharge machining (EDM). Int J Mach Tools Manuf 43(13): 1287–1300. http://dx.doi.org/10.1016/S0890-6955(03)00162-7
Ho KH, Newman ST, Rahimifard S, Allen RD (2004) State of the art in wire electrical discharge machining (WEDM), International Journal of Machine Tools and Manufacture, Volume 44, Issues 12–13, Pages 1247–1259, ISSN 0890–6955, http://dx.doi.org/10.1016/j.ijmachtools.2004.04.017
Masuzawa T (2000) State of the art of micromachining. CIRP Ann Manuf Technol 49(2):473–488
Yu ZY, Masuzawa T, Fujino M (1998) Micro-EDM for three-dimensional cavities—development of uniform wear method. CIRP Ann Manuf Technol 47(1):169–172
Rajurkar KP, Yu ZY (2000) 3D micro-EDM using CAD/CAM. CIRP Ann Manuf Technol 49(1):127–130
Anwar MM, Saleh T, Madden JDW, Takahata K (2014) Micropatterning polypyrrole conducting polymer by pulsed electrical discharge. Macromol Mater Eng 299(2):198–207
Saleh T, Dahmardeh M, Bsoul A, Nojeh A, Takahata K (2011) Field-emission-assisted approach to dry micro-electro-discharge machining of carbon-nanotube forests. J Appl Phys 110(10):7
Saleh T, Dahmardeh M, Bsoul A, Nojeh A, Takahata K (2012) High-precision dry micro electro-discharge machining of carbon-nanotube forests with ultralow discharge energy. 2012 I.E. 25th International Conference on Micro Electro Mechanical Systems (MEMS)
Saleh T, Dahmardeh M, Nojeh A, Takahata K (2013) Dry micro-electro-discharge machining of carbon-nanotube forests using sulphur-hexafluoride. Carbon 52:288–295
Reynaerts D, Heeren PH, Brussel HV (1997) Microstructuring of silicon by electro-discharge machining (EDM).1. Theory. Sensors and Actuators a-Physical 60(1–3):212–218
Luo YF, Chen CG, Tong ZF (1992) Investigation of silicon wafering by wire EDM. J Mater Sci 27(21):5805–5810
Peng WY, Liao YS (2003) Study of electrical discharge machining technology for slicing silicon ingots. J Mater Process Technol 140:274–279
Wang W, and Liu ZD (2009) High efficiency slicing of low resistance silicon ingot by wire electrolytic-spark hybrid machining. J Mater Process Technol 209(7):3149–3155. http://dx.doi.org/10.1016/j.jmatprotec.2008.07.029
Okamoto Y, Uno Y, Okada A, Ohshita S, Hirano, T. and Takata S (2008) Development of multi-wire EDM slicing method for silicon ingot. Proceedings of ASPE Annual Meeting and the 12th ICPE
Crawford GA (2012) Process characterization of electrical discharge machining of highly doped silicon. Master of Science Thesis in Mechanical Engineering, Massachusetts Institute of Technology, USA
Staufert GA, Dommann V, Lauger D (1993) Behaviour of a silicon spring fabricated by wire electro-discharge machining. J Micromech Microeng 3(4):4
Rakwal D, Heamawatanachai S, Tathireddy P, Solzbacher F, Bamberg E (2009) Fabrication of compliant high aspect ratio silicon microelectrode arrays using micro-wire electrical discharge machining. Microsyst Technol Micro Nanosyst -Inf Storage Process Syst 15(5):789–797
Yu PH, Lin YX, Lee HK, Mai CC, Yan BH (2011) Improvement of wire electrical discharge machining efficiency in machining polycrystalline silicon with auxiliary-pulse voltage supply. Int J Adv Manuf Technol 57(9–12):991–1001
Zhidong L, Haoran C, Huijun P, Mingbo Q and Zongjun T (2014) Automatic control of WEDM servo for silicon processing using current pulse probability detection. Int J Adv Manuf Technol. Published Online 30 Aug 2014. doi:10.1007/s00170-014-6252-2
Jahan MP, Lieh TW, Wong YS, Rahman M (2011) An experimental investigation into the micro-electrodischarge machining behavior of p-type silicon. Int J Adv Manuf Technol 57(5–8):617–637
Song X, Meeusen W, Reynaerts D, Brussel HV (2000) Experimental study of micro-EDM machining performances on silicon wafer. Proc SPIE 4174, Micromachining and Microfabrication Process Technology VI:331. doi:10.1117/12.396450
Takino H, Ichinohe T, Tanimoto K, Yamaguchi S, Nomura K, Kunieda M (2004) Cutting of polished single-crystal silicon by wire electrical discharge machining. Precis Eng-J Int Soc Precis Eng Nanotechnol 28(3):314–319
Takino H, Ichinohe T, Tanimoto K, Yamaguchi S, Nomura K, Kunieda M (2005) High-quality cutting of polished single-crystal silicon by wire electrical discharge machining. Precis Eng-J Int Soc Precis Eng Nanotechnol 29(4):423–430
Rasheed AN, Asan GA, Saleh T (2013) Enhancing μ-wedming (wire electro-discharge machining) of polished silicon wafer by conductive coating. J Manufact Tech Res 5(1–2):1–17
Mahardika MT, Tsujimoto, Mitsui K (2008) A new approach on the determination of ease of machining by EDM processes. Int J Mach Tools Manufact 48(7–8):746–760
Masanori K, Satoyuki O (2000) Improvement of EDM efficiency of silicon single crystal through ohmic contact. Precis Eng 24:185–190
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Saleh, T., Rasheed, A.N. & Muthalif, A.G.A. Experimental study on improving μ-WEDM and μ-EDM of doped silicon by temporary metallic coating. Int J Adv Manuf Technol 78, 1651–1663 (2015). https://doi.org/10.1007/s00170-014-6732-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-014-6732-4