Abstract
In this research, the exponential and quadratic polynomial empirical models for three-component cutting forces by employing five factors, such as the cutting speed, depth of cut, feed, workpiece hardness, and nose radius, were developed by utilizing the orthogonal regression methodology (ORM) and response surface methodology (RSM). On the other hand, an attempt has been made to experimentally investigate the effects of those factors on three-component cutting forces in finish dry hard turning (FDHT) of tool steel AISI D2 with the PCBN tool. In this investigation, based on five-factor three-level orthogonal experiments, three-component cutting forces were measured, and then, analysis of variance (ANOVA) was performed to estimate the significance of developed models and analyze the main and interaction effects of the factors. The experimental results indicated that the RSM quadratic polynomial empirical model (RSMQPEM) is much more accurate and credible than the ORM exponential empirical model (ORMEM) in predicting the three-component cutting forces. It was also found that the cutting speed and feed are the two dominant factors affecting the main cutting forces F Z; the feed is the one dominant factor affecting radial cutting force F Y and the feed cutting force F X. Additionally, the optimum cutting parameters for the hardened materials with 51, 55, 60, and 64 HRC was found.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Gaitonde VN, Karnik SR, Figueira L, Paulo Davim J (2009) Analysis of machinability during hard turning of cold work tool steel (type: AISI D2). Mater Manuf Process 24(12):1373–1382
Klocke F, Brinksmeier E, Weinert K (2005) Capability profile of hard cutting and grinding processes. Ann CIRP 54(2):552–580
Ranganathan S, Senthilvelan T (2009) Behavior of machining parameters in hard turning of 316 stainless steel. Int J Manuf Sci Prod 10(2):137–145
Tang L, Huang J, Xie L (2011) Finite element modeling and simulation in dry hard orthogonal cutting AISI D2 tool steel with CBN cutting tool. Int J Adv Manuf Technol 53(1/2):1167–1181
Tang L, Gao C, Huang J, Lin X, Zhang J (2014) Experimental investigation of the three-component forces in finish dry hard turning of hardened tool steel at different hardness levels. Int J Adv Manuf Technol 70(9–12):1721–1729
More WC, Jiang W, Brown WD, Malshe AP (2006) Tool wear and machining performance of cBN-TiN coated carbide inserts and PCBN compact inserts in turning AISI4340 hardened steel. J Mater Process Technol 180(1–3):253–262
Sharma VS, Dhiman S, Sehgal R, Sharme SK (2008) Estimation of cutting forces and surface roughness for hard turning using neural networks. J Intell Manuf 19(4):473–483
Sieben B, Wagner T, Biermann D (2010) Empirical modeling of hard turning of AISI 6150 steel using design and analysis of computer experiments. Prod Eng 4(2):115–125
Ding T, Zhang S, Wang Y, Zhu X (2010) Empirical models and optimal cutting parameters for cutting forces and surface roughness in hard milling of AISI H13 steel. Int J Adv Manuf Technol 51(1):45–55
Gopalsamy B, Mondal B, Ghosh S (2009) Optimisation of machining parameters for hard machining: grey relational theory approach and ANOVA. Int J Adv Manuf Technol 45(11–12):1068–1086
Fnides B, Yallese MA, Mabrouki T, Rigal JF (2011) Application of response surface methodology for determining cutting force model in turning hardened AISI H11 hot work tool steel. Sadhana 36(1):109–123
Aouici H, Yallese MA, Chaoui K, Mabrouki T, Rigal JF (2012) Analysis of surface roughness and cutting force components in hard turning with CBN tool: prediction model and cutting conditions optimization. Measurement 45(3):344–353
Zhou AQ, Deng FY (2001) Experimental study on the heat treatment process for Cr12MoV steel. Die Mould Ind 000:55–57
Wang LJ, Miao B, Meng XX (2005) Analysis on the hardness and metallographic structure of Cr12MoV Steel under different heat treatment. Die Mould Ind 000:2–56
Dogra M, Sharma VS, Sachdeva A, Suri NM, Dureja JS (2010) Tool wear, chip formation and workpiece surface issues in CBN hard turning: a review. Int J Precis Eng Manuf 11(2):341–358
Wen D (2002) The mechanism and technology of hard turning with PCBN tool. Dalian University of Technology, Dissertation
Liu Z, Wan Y, Zhou J (2006) Tool materials for high speed machining and their fabrication technologies. Mater Mech Eng 30(5):1–4
Kilickap E, Huseyinoglu M, Yardimeden A (2011) Optimization of drilling parameters on surface roughness in drilling of AISI 1045 using response surface methodology and genetic algorithm. Int J Adv Manuf Technol 52(1–4):79–88
Natarajan U, Periyanan P, Yang S (2011) Multiple-response optimization for micro-endmilling process using response surface methodology. Int J Adv Manuf Technol 56(1–4):177–185
Tang Z (1997) Fundamental of mechanical manufacture. 1st edn. Machinery Industry Press, Beijing, p 11–12
Yuan Z, Song S (2009) Multivariate statistical analysis, 1st edn. 102, Beijing, pp 102–116
Fang K, Quan H (1988) Applied regression analysis, 1st edn. Science Press, Beijing, pp 202–206
Ren L (2009) Regression design and optimization, 1st edn. Science Press, Beijing, pp 232–256
Chen C, Chiang K (2011) Analyzing the design of vibration reduction with the rubber-layered laminates in the precision turning with a diamond cutting tool. Int J Adv Manuf Technol 19(1–4):101–116
Li X, Yin X (2008) SPSS economic and statistical analysis, 1st edn. China Statistics Press, Beijing, pp 261–289
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Tang, L., Cheng, Z., Huang, J. et al. Empirical models for cutting forces in finish dry hard turning of hardened tool steel at different hardness levels. Int J Adv Manuf Technol 76, 691–703 (2015). https://doi.org/10.1007/s00170-014-6291-8
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-014-6291-8